Smeg CIR597X5 инструкция обслуживания

Contents 1. INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4 2. POSITIONING OF HOB ____________________________________ 6 3. GAS CONNECTION ______________________________________ 11 4. ELECTRICAL CONNECTION ______________________________ 12 5. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 13 6. FINAL OPERATIONS _______________________[...]

Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C O OKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SER IES OF NOZZLES S[...]

Introduction THE IDENTIFICATION PLATE, W ITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE R EMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY S [...]

Instructions for the installer 6 2. POSITIONING OF HOB The following operation r equires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silicone or[...]

Instructions for the installer 7 Overall dimensions: location of gas and electrical connection points (all measures in mm). A 100 B 350 C 60 D 60[...]

Instructions for the installer 8 2.2 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measureme nt A ) Range hoods and exha ust fans shall be installed in accor dance with the manufacturer’s instructions. Howev er, in no case shall the clearance between the highest part of the hob of the c[...]

Instructions for the installer 9 2 Side clearances – (Measurements B & C) Where B , measured from the periphery of the n earest burner to any vertical com bustible surface , is less than 200 mm , the surface shall be protected in accorda nce with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for th e full dimension (widt[...]

Instructions for the installer 10 2.3 Room ventilation Caution – This hob may o nly be installed and operated in rooms permanently ventilated in accordance with current regulations. For proper operation of a gas a ppliance it is essential for the air nec essary for combustion of the gas to be able to flow naturally into t he room. Air must flow d[...]

Instructions for the installer 11 3. GAS CONNECTION This appliance is su itable for installation with Natural Gas or ULPG (propane). R efer to page 12 for the relevant burner press ure and appropriate injector sizes. When the ap pliance is to be connected to Natural Gas then the pressure regulator supp lied must be fitted to the gas inlet. A te st [...]

Instructions for the installer 12 4. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syste[...]

Instructions for the installer 13 5. AD APT A TION T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been adjusted for natural gas at a pressure of 1.0kPa. For functioning with other types of gas the nozzles must be replaced and the primary air adjusted. To re[...]

Instructions for the installer 14 5.2 Regulation for LPG Loosen screw A and push support B all the way. Use a d ouble head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque of the nozzle should never exceed 3 Nm. Repositi[...]

Instructions for the installer 15 5.3 Regulation for natural gas The hob has been adjusted for natura l gas at a pressure of 1.0kPa. To allow the unit to work back with this type of g as, after it has been adjusted for LPG, perform the same operations described i n paragraph “5.2 Adjustment for LPG”, but refer to the following table for the pro[...]

Instructions for the installer 16 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the instructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the compon ents on the burner and slide the knobs on the gas tap pins. Light the burner and se[...]

Instructions for the user 17 7. USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intende d for use with woks (Chinese pans). Adapter D comes only with open grids models and is int ended for use wi[...]

Instructions for the user 18 7.2 Practical advice for usin g the burners For better burner performance an d minimum gas consumption, flat bottomed, even recipie nts must be used, with covers and proportiona l in size to the burners (see paragraph “ 7.3 Diameter of containers ”). To avoid overcooking or damage to the surface top w hile cooking, [...]

Instructions for the user 19 8. LEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su rface, always use specific products only , which [...]

Instructions for the user 20 8.2.1 Ignition plugs and safety devices For good functioning of the l ighting ignition plugs and the s afety devices, keep them very clean. Check frequently and clean with a damp clot h when necessary. 8.2.2 The electric element After use, to make sure that the s urfaces are clean and long lasting, the electric element [...]

[...]

914773030/ B[...]