Smeg GKC755 инструкция обслуживания

Contents 21 1 INSTRUCTIONS FOR SAFE A ND PROPER USE ____________________ 22 2 POSITIONING OF THE HOB ____________________________________ 24 3 ELECTRICAL CONNECTION ____________________________________ 26 4 GAS CONNE CTION ___________________________________________ 27 5 ADAPTATION TO DIFFER ENT TYPES OF GAS _____________________ 29 6 FINAL OPER AT[...]

Introduction 22 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE AP PLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WH OLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SU[...]

Introduction 23 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB. DO NOT PUT PANS WITHOUT PERFECTLY SMOOT[...]

Instructions for the installer 24 2 POSITIONING OF THE HOB The following operation requ ires bui lding and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials suc h as masonry, metal, solid wood or plastic laminated woo d as long as they are heat resistant (T 90°C). Never use sili[...]

Instructions for the installer 25 In case of installation on a hollow compartment with doors, a separating panel has to b e placed under the hob. Keep a minimum distance of 10 mm between the bottom of the unit and the pane l surface. The panel has to be easily removable to allow access in the event of technical service.[...]

Instructions for the installer 26 3 ELECTRICAL CONNECTION Make sure that the voltage and capa city of the pow er line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syste[...]

Instructions for the installer 27 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe o r with a flexible pipe and conforming to the provisions defined b y standard regulations in force. To facilitate connection, fitting A on the rear of the appliance ma y be adjusted laterally. For this p urpose, loosen hexagon nut B [...]

Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisio ns of st andards r egulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph “5.2 Regulation for LPG”. 4.2 Ventilation of rooms The hob may be installed onl[...]

Instructions for the installer 29 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any clea ning or maintenance work, dis connect the appliance from the electrical socket. The hob has been ins pected for G25 (2L 3B/P) at a pressure of 25 mbar. For functioning with other types of gas the nozzles must be replaced and the primary a ir adjusted[...]

Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push support B all the way. Use a double hea d wrench to remove nozzle C and assemble the suitable on e, following the instructions indicated in the refere nce charts, with respect to the type of gas to use. The screwing torque of the nozzle should nev er exceed 3 Nm . Repo[...]

Instructions for the installer 31 5.3 Regulation for natural gas The hob has been ins pected for G25 (2L 3B/P) at a pressure of 25 mbar. To allow the unit to work with this type of gas, perform the same operations described in para graph “5.2 Regulation for LPG”, but choose the nozzles and regulate the primary ai r for natura l gas, as shown in[...]

Instructions for the installer 32 5.4 Regulation of primary air Referred to distance “ X ” in mm. G25 G30/G31 Burner 25 mbar 28/37 mbar Auxiliary (1) 1.0 1.0 Semirapid (2) 1.0 1.5 Rapid (3) 0.5 1.5 Rapid large (4) 1.5 10.0 Fish pan (7) 1.5 2.5 Ultra rapid (5) 1.5 2.5 Ultra rapid (8) 1.5 2.5 Internal 1.0 6.0 Double crown (6) External 1.5 10.0 In[...]

Instructions for the installer 33 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble the ap pliance following, backwards, the instructions i n paragraph “ 5.1 Removing the hob”. 6.1 Regulation of minimum for natural gas Replace the components on the burner a nd slide the knobs on the gas tap pins. Light the burner and set i[...]

Instructions for the installer 34 6.3 Arrangement of burners on hob Burners 1. Auxiliary 2. Semirapid 3. Rapid 4. Rapid large 5. Ultra rapid 6. Double crown 7. Fish pan 8. Ultra rapid 9. Double crown 6.4 Lubrication of gas taps After a while, the gas tap may become ha rd to turn or lock. If this happens, it has to be cleaned inside and re-greased. [...]

Instructions for the user 35 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted cor rectly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C (where available) is int ended for use with woks (Chinese p ans). Adapter D co mes only with open grids models and is intend ed[...]

Instructions for the user 36 7.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottom ed, even pans must be used, with covers and proportional in size to the burners (see paragraph “ 7.3 Diameter of the pans”). To avoid overcooking or damage to the surface top or to the glass (where avail[...]

Instructions for the user 37 8 CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the appliance. 8.1 Cleaning Clean the cooking top regularl y every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and pres erve the s[...]

Instructions for the user 38 8.2 Cleaning of cooking hob components CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the st ainless st eel burner caps and pan - stands tend to be burnished by the high temperature. Clean thes e parts using very fine abrasive sponges or similar commercial prod ucts. Then use a specific[...]