Smeg P705VT инструкция обслуживания

Contents 18 1. Instructions for safe and proper use ____________________ 19 2. Positioning of hob __________________________________ 20 2.1 Attachment to s upport structure ________________________________________20 3. Electrical co nnection _______________________________ 22 4. Gas connect ion ___________________________________ 23 4.1 Connection [...]

Instructions for safe and proper use 19 1. Instructions f or safe and pr oper use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN IT S ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOL E WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USI NG THE COOKING HOB. ALSO K[...]

Instructions for the installer 20 2. P ositioning of hob The following op eration requires building and/or carpentry work so must be carri ed out by a competent tradesman. Installation can be carried out on various materials such as ma sonry, metal, solid wood or plastic laminated wood as lon g as they are heat resistant (T 90°C). 2.1 Attachment t[...]

Instructions for the installer 21 Before mounting the device to the unit, lay the provided adhe sive sponge onto the glass surf ace to separate it from the unit. After fixing the provided adhesive spon ge (B) to the glass, mount the device to the unit with the mounting brackets (A) provided with the device itself, as shown in the figure. When fixin[...]

Instructions for the installer 22 3. Electrical connection Make sure that the voltag e and capacity of the power line co nform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electri cal syst[...]

Instructions for the installer 23 4. Gas connection If the appliance is installed on an oven, the gas pi pe must not be passed along the back of the oven, as this may cause overheating. Connection to the gas mains may be m ade with a rigid copper pipe or with a flexible pipe and conforming to the provisions d efined by standard regulations in force[...]

Instructions for the installer 24 4.1 Connection to LPG Use a pressure regulator and m ake the connection to the tank according to the provisions of standard s regulations in force. Make sure that feed pressure conforms to the levels shown in the table in Section “5.2 Regulation for LPG ”. 4.2 V entilation of rooms The hob may be installed only[...]

Instructions for the installer 25 5. Adapting to different types of gas Before performing any cleaning or mainte nance work, detach the hob from the electrical socket. The hob has been inspect ed for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other t ypes of gas t he nozzles m ust be replaced and the primary air adjusted. T[...]

Instructions for the installer 26 5.2 Regulation fo r LPG Loosen screw C and push air re gulator D to the bottom. With a 7 mm wrench, remove nozzle E and replace it with the proper one (follow the instructions on the referen ce tables for the type of gas to be used). The torque wren ch setting of the nozzle must not exceed 3 Nm . Regulate the air b[...]

Instructions for the installer 27 5.4 Regulation of primary air Referred to distance “ X ” in mm. BURNER G20 20 mbar G30/G31 28/37 mbar Auxiliary 4 open Semi rapid 3 2 Medium rapid 2 2.5 Large rapid 2 2.5 A 2 14 UR B 2 14 To identify the burners on your ho b, refer to the drawi ngs in point “5 .8 Arrangement of burners on ho b “ If after ai[...]

Instructions for the installer 28 5.7 Regulation of minim um for LPG To regulate the minimum for LPG, completely tighten (clockwi se) the screw inside or next to the gas tap pin (depending on the model). The diameters of the by-passes for ea ch burner are given in table “5.2 Regulati on for LPG ”. After regulation for a gas other than that insp[...]

Instructions for the user 29 6. Description of contr ols 6.1 Fr ont control panel All of the commands and controls for the hob are fou nd on the front panel. MODEL 60 CONTROL PANEL MODEL 70 CONTROL PANEL MODEL 100 CONTROL P ANEL DESCRIPTION OF THE KNOB The flame is lit by pressing the knob and simultaneo usly turning it anticlockwise to the minimum[...]

Instructions for the user 30 7. Using the hob Check that the flame cap c rowns, the burner caps and grids are correctly assembled. Pins A of the flame cap crowns must be inserted in housings B of the burner rings, and pins C on the grids must be blocked in their respective housings on the hob. 7.1 Burner lighting with safety de vice Each knob shows[...]

Instructions for the user 31 8. Cleaning and maintenance Never use a steam jet to clean the appliance. Before any inter vention, disconnect the power supply of the d evice. 8.1 Cleaning stainless steel To keep the hob in good condition, you should clean it after every use (after it has cooled). 8.1.1 Regular daily cleaning of the hob To clean and p[...]