Smeg PGF95BE-1 инструкция обслуживания

Summary 1 INSTRUCTIONS FOR SAFE AND PROPER USE ______________ 20 2 POSITIONING OF THE HOB ______________________________ 22 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS ______________ 29 4 FINAL OPERATIONS ____________________________________ 31 5 USING THE HOB _______________________________________ 32 6 CLEANING AND MAINTENANCE ________________________[...]

Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS EN TIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION[...]

Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE REMOVED . DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB PANSTAND GRIDS. DO NOT USE COOKING RECEPTACLES THAT EXT[...]

Instructions for the installer 2 POSITIONING OF THE HOB The following operation requires buildi ng and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminat ed wood, as long as they are heat- resistant (T 90°C). 2.1 Attachment to[...]

Instructions for the installer 2) 3) 4) 23[...]

Instructions for the installer 2.2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. The lower part of the protective cover must be fully accessible when the appliance is installed. This appliance can be insta[...]

Instructions for the installer Overall dimensions: location of gas and electrical connection points (all measures in mm). Caution: surface temperature underneath may exceed 125 degrees C. To avoid a hazard, under-bench access must be restricted. Refer to installation instruction IMPORTANT: when installing the app liance above a cupboard, a dividing[...]

Instructions for the installer 2.3 Electrical connection Make sure that the voltage and capacit y of the power supply cable conform to the data shown on the plate loca ted under the protective cover. Do not remove this plat e for any reason . The power supply cable plug and the wa ll socket must be of the same type and conform to the current electr[...]

Instructions for the installer 2.4 Ventilation requirements The appliance may be installed only in rooms with permanent ventilation, as required by UNI-CIG 7129 / 7131 st andards. The room in which the appliance is installed must have sufficient air flow to satisfy the requirements of normal gas combus tion and of necessary air exchange in the room[...]

Instructions for the installer 2.6 Gas connection Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe conforming to the prov isions defined by UNI-CIG 7129. After connection operations, check for leaks using a soapy solution. The hob has been inspected for G20 natural gas (2H) at a pressure of 20 mbar. For use w[...]

Instructions for the installer 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug th e appliance from the mains. The hob is set for natural gas G20 (2H) at a pressure of 20 mbar. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjust ed on the[...]

Instructions for the installer 3.2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) LPG – G30/G31 30/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Reduced flow rate (W) Flow rate g/h G30 Flow rate g/h G31 Auxiliary (1) 1.05 50 27 (*) 28 (**) 350 76 75 Semi rapid (2) 1.8 65 33 (*) 32 (**) 450 130 128 Rapid (3) 2.3 75 [...]

Instructions for the installer 4 FINAL OPERA TIONS After carrying out the above adjustments, remount in reverse order to the instructions given in paragraph “3.1 Replacement of nozzles on the hob”. After adjustment to a different kind of gas from the one for which the appliance has been tested, replace the plate inside the storage compartment w[...]

Instructions for the user 5 USING THE HOB 5.1 Ignition of the burners Before turning on the burners, make sure that the flame-spreader crowns and respective caps are proper ly fitted in their housings. Ensure the flame-spreader holes A are aligned with the ignition plugs and the thermocouples. Panstand grid B , available upon request, is intended f[...]

Instructions for the user 5.2 Practical advice for using the burners For better use of the burners and lowe r gas consumption, use covered cooking receptacles that have a flat, smooth bottom and are proportional in size to the burner to prevent the flame from licking the sides (see paragraph “5.3 Diameter of receptac les”). When water reaches b[...]

Instructions for the user 6 CLEANING AND MAINTENANCE Before any intervention, disconnect the appliance from the mains. 6.1 Cleaning the stainless steel To keep stainless steel in good c ondition it should be cleaned regularly after use. Let it cool first. 6.1.1 Routine daily cleaning To clean and preserve the stainl ess steel surfaces, always use o[...]