Smeg PTS723-3 инструкция обслуживания

Table of Contents 3 1. Precautions for safety and use _________________________ 4 2. Fitting the appliance in the top _________________________ 5 2.1 Fixing to the supporting structure ________________________________________5 3. Electrical connection ________________________________ 7 4. Gas connection ____________________________________ 8 4.1 Bo[...]

Precautions for Safety and Use 4 1. Precautions f or safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CY CLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT C ONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE.[...]

Instructions for the Installer 5 2. Fitting the appliance in the top The procedures required below must be carried o ut by a skilled builder and/or joiner. The hob can be installed on vari ous materials, including masonry, metal, solid wood and wood finished with plastic laminates, pr ovided the material is heat-resistant (T 90° C). 2.1 Fixing to [...]

Instructions for the Installer 6 Fit the insulating gasket provided carefu lly around the outside edge of the hole made in the top as shown below, pressi ng it down with your hands so that its entire surface fits snugly. Follow the dimensions shown, dependi ng on the model of hob to be installed, bearing in mind that on both models the long fr ont [...]

Instructions for the Installer 7 3. Electrical connection Check that the power su pply line voltage and size are as speci fied on the nameplate underneath the applian ce's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant re gulat[...]

Instructions for the Installer 8 4. Gas connection If the appliance is installed above an ov er, t he gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains ma y be made using a copper pipe or a continuou s-wall steel hose in accordance with the relev ant regul ations. To simplify connection, the[...]

Instructions for the Installer 9 4.1 Bottled gas connection Use a pressure regulator and ma ke the connection to the gas cylin der in accordance with the relevant regulations. Make sure that the gas supply pressure is as st ated in the table in point "5.2 Adjusting for bottled gas". 4.2 Room ventilation The appliance may only b e installe[...]

Instructions for the Installer 10 5. Adapting to diff erent types of gas Before carrying out the operations described below, disconnect th e appliance from the electricity supply. The hob is tested with G20 (2H) natural gas at the pressure of 20 mbar. If it is to be used with other types of ga s, the burn er nozzles have to be changed and the prima[...]

Instructions for the Installer 11 5.2 Adjusting fo r bottled gas Undo the scr ew A and push the support B fully do wn. Remove the nozzle C with a spanner and fit the suitabl e one following the instructions in the tables referring to the type of gas to be used. The nozzl e must not be tightened with a torque of more than 3 Nm . Return the support B[...]

Instructions for the Installer 12 5.5 Adjusting the primary air flow Refers to the gap “ X ” in mm. BURNER G30/G31 30/37 mbar G110 8 mbar G20 20 mbar Semi rapid (1) 10.0 1.5 2.0 Rapid (2) 8.0 1.5 2.5 Ultra-Rapid (3) 12.0 5.0 2.5 To identify the burners on you r hob, refer to the drawings in point “5.8 Hob burne r layout” 5.6 Reassembling th[...]

Instructions for the Installer 13 5.9 Hob b urner lay out Burner type 1 Semi rapid 2 Rapid 3 Ultra-Rapid 5.10 Greasing the gas taps Over time, the gas taps may beco me stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician.[...]

Instructions for the User 14 6. Description of contr ols 6.1 The fr ont panel All the hob's control and monitori ng devices are placed together on the front panel. KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone betwe[...]

Instructions for the User 15 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. 7.1 Lighting b urners [...]

Instructions for the User 16 8. Cleaning and maintenance Before carrying out any operations, disconnect the ap pliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regula rly, after each u se, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning an d caring for [...]

[...]

914773119/ B[...]