Snapper SGV13320KW инструкция обслуживания

GVTP SM32-R0303.1 ASSEMBLY INSTRUCTIONS OPERATOR’S MANUAL PARTS LIST Walk-Behind Mower 32” cut model Actual product may differ slightl y from product pictured above Models covered: SGV13320KW[...]

GVTP SM32-R0303.1 This pa ge inten tionally bl ank[...]

GVTP SM32-R0303.1 1 preliminaries Congratulations! You have just purchased one of the finest pieces of out door power equipment on the market today. If properly cared for, your new mower will provide years of dependabl e service. Please read and follow this instruction manual carefully in order to get the most out of your new equipment. As you care[...]

GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment PLEASE READ THE FOLLOWING BEFORE ASSEMBLING OR OPERATING UNIT TRAINING • Read, understand, and follow all instructions in the manual and on the unit before starting. If the operator(s) or mechanic(s) can not read English it is the owner’s responsibility to explain this material [...]

GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope, or if you feel uneasy on it, do not drive on it. Do • Mow across the [...]

GVTP SM32-R0303.1 2 safety rules regarding outdoor power equipment (cont.) • Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recommended parts, when necessary. • Check brake operation frequently. [...]

GVTP SM32-R0303.1 3 unit assembly (cont.) DISCHARGE DEFLECTOR ASSEMBLY • Attach discharge deflector (1:5) using two 5/16" x ¾ " bolts and lock nuts (1:6-7). CAUTION: Do not over tighten lock nuts. TRANSMISSION SHIFT LEVER ASSEMBLY • Install Shift indicator panel (2:45) onto rear of engine deck (2:1) with two 5/16 x 3/4” hex bolts ([...]

GVTP SM32-R0303.1 3 unit assembly (cont.) TRANSMISSION SHIFT LEVER ASSEMBLY (cont.) • Position ‘double-D’ hole in bottom leg of shift lever onto transmission stud, then slowly move handle of shifter back and forth until hole drops onto matching base of stud. • Replace washer and nut onto transmission stud. Tighten securely. Replace lock nut[...]

GVTP SM32-R0303.1 3 unit assembly (cont.) HANDLE ASSEMBLY INSTALLATION • Install handle assembly (4:1) to upper portion of engine deck using four 1/2" x 1-1/4" hex bolts and serrated flange nuts (4:3-4). Adjust for comfortable operation, then tighten securely. • Locate wiring harness and route harness down the right side of handle ass[...]

GVTP SM32-R0303.1 4 unit operation STARTING THE ENGINE IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer’ s oper ating instructions. In order to obtain optimum performance from your engine, refer to your engine manual. BEFORE STARTING ENGINE: •[...]

GVTP SM32-R0303.1 4 unit operation (cont.) STARTING THE ENGINE (cont.) • Grasp recoil handle and pull briskly. You may have to pull several times before engine starts. (If engine fails to start within a reasonable amount of time, discontinue and check engine manual for further instructions.) Note: Do not allow recoil rope to snap back into recoil[...]

GVTP SM32-R0303.1 4 unit operation (cont.) • Learn to listen to your machine – being aware of w hat a well-running unit sounds like can alert you to a potential problem. A straining engine or clanging blades or a slapping belt mean that trouble is almost sure to follow. ENGAGING THE CUTTING BLADES: Note: Never engage the mow er blades until you[...]

GVTP SM32-R0303.1 4 unit operation (cont.) • Move the shift lever to first gear (‘1’), unlock brakes, and slowly release the brake handles. • Your mower has five forward speeds (‘1’ – ‘5’); simply slide the shifter lever to the appropriate indicator position to select that gear. The machine can be shifted on the run. NOTE : If cli[...]

GVTP SM32-R0303.1 5 maintenance GENERAL: • Follow implicitly the engine manufacturer’s recommendations for maintenance. • Always keep your machine clean - especially the engi ne deck. Check all adjustments periodically. Also, periodically check that all fasteners are secure. Reme mber, sharp blades cut better. Always have an extra set on hand[...]

GVTP SM32-R0303.1 5 maintenance (cont.) TROUBLESHOOTING: • UNIT WILL NOT START: Check to make sure cutting blades are disengaged. Check to make sure transmission is in neutral. Check fuel and oil levels. Check to make sure throttle control engages engine choke when set to ‘start’ position; adjust if needed. Check all electrical connec tions f[...]

GVTP SM32-R0303.1 5 maintenance (cont.) • THROTTLE/CHOKE CABLE ADJUSTMENT: Correct throttle cable adjustment allows for full range of motion on engine throttle body in conjunction with throttle control on handle dash. Correct choke cable adjustment engages choke when choke knob is pulled fully out. To adjust either cable, loosen cable clip screw [...]

GVTP SM32-R0303.1 5 maintenance (cont.) • BRAKE ADJUSTMENT: LOWER ROD - The brake assembly has been set at the factory. However, they may periodically need adjustment. As a rule of thumb, the bottom bend of the lower brake rod (3:14) should be 3/8” lower than the center of the pivot boss hole in the brake arm (3:5). If adjustment is needed, sim[...]

GVTP SM32-R0303.1 5 maintenance (cont.) • SIDE IDLER TENSION SPRING ADJUSTMENT: To increase tension, remove nut and lock washer securing rear spring hanger bolt (3:34) in middle tension hole, and replace bolt in uppermost hole. To decrease tension, replace in lowest hole. Replace lock washer and nut, tightening securely. If tension is still slack[...]

GVTP SM32-R0303.1 19 18 23 24 32" Cut Mower BLADE DECK GROUP SHEET 1 OF 4 R0303.1 15 12 12 13 15 14 16 41 5 10 9 8 11 17 21 26 6 7 25 20 A 29 A thru 44 22 32 27 31 30 25 28 34 33 31 40 36 35 43 37 38 45 To Blade Pu lley - See Engine & Trans Group 47 46 1 2 42 39 3 4 See Engine & Trans Group[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP REF # PART # QTY DESCRIPTION 1 3010260 1 Blade deck --- 3079166 1 Decal – ‘Operating Rules 1-8’ --- 3079090 2 Decal – ‘Danger – Keep Hands & Feet Away’ --- 3079088 1 Decal – ‘Danger – Flying Material’ --- 3079091 1 Decal – ‘Caution-Rotating Pa[...]

GVTP SM32-R0303.1 34 3031987 1 3/8-16 small serrated flange nut Snapper 32” Cut Mower R0303.1 SHEET 1 - BLADE DECK GROUP (cont.) REF # PART # QTY DESCRIPTION 35 3031410 1 3/8-16 x 2" carriage bolt 36 3031686 1 3/4" spacer bushing 37 3036120 1 Deck idler pulley 38 3032132 1 3/8-16 large serrated flange nut 39 3031402 1 3/8" ball joi[...]

GVTP SM32-R0303.1 14 29 To Driv e Wheel - See Side Idler & Axle Gro up 32" Cut Mower ENGINE & TRANS GROUP SHEE T 2 OF 4 R0303.1 To Blade Pulleys - See Blade Deck Gr oup 13 12 11 10 To Re f #8 th is sheet 3 4 5 24 9 8 1 7 19 22 20 25 26 23 17 18 37 16 28 6 27 34 21 56 59 42 35 36 32 31 48 33 31 2 N 5 4 29 30 27 A 15 28 2 3 1 41 64 58 60[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower SHEET 2 - ENGINE & TRANS GROUP REF # PART # QTY DESCRIPTION (no model designation denotes common) 1 3010261 1 Engine base --- 3027503 1 Blade cam cover plate --- 3031573 2 #10 x 1/2” sheet metal screw 2 3039121 1 Engine - 13hp Kawasaki w/5 amp coil 3 3031006 4 5/16-18 x 1-1/2” hex bolt 4 3031027 1 5[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower SHEET 2 - ENGINE & TRANS GROUP (cont.) REF # PART # QTY DESCRIPTION 41 3023182 3 1/2" oillite washer 42 3031637 1 1/2-13 nylon lock nut 43 3031915 1 3/8-24 nylon lock nut 44 3031034 1 3/8" flat washer 45 3027412 1 Shift panel 46 3079096 1 Shift decal 47 3031031 2 5/16-18 x 3/4" hex bolt 4[...]

GVTP SM32-R0303.1 1 32" Cut Mower SIDE IDLER & AXLE GROUP SHEET 3 OF 4 R0303.1 13 32 23 10 4 3 2 24 11 thru 20 18 17 15 14 9 8 A 28 26 25 27 19 16 12 7 6 5 See Engine & Trans Group 33 31 43 42 30 A 21 22 See Handle Group 34 41 36 37 35 29 37 35 38 40 39[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 3 - SIDE IDLER & AXLE GROUP REF # PART # QTY DESCRIPTION 1 3033231 1 Axle assembly 2 3027407 1 Brake pivot plate - left --- 3027408 1 Brake pivot plate - right 3 3031008 4 3/8" lock washer 4 3031033 4 3/8-16 x 1 hex bolt 5 3023152 1 Brake arm - left --- 3023151 1 Brake arm - right ---[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 3 - SIDE IDLER & AXLE GROUP (cont.) REF # PART # QTY DESCRIPTION 38 3027511 1 Wheel drive pulley cover – left --- 3027512 1 Wheel drive pulley cover – right 39 3031031 2 5/16-18 x 3/4” hex bolt 40 3031986 2 5/16-18 small serrated flange nut 44 3031383 2 Rod fitting end (trunion) 45 3[...]

GVTP SM32-R0303.1 32 14 See Engine & Tra ns Group See Side Id ler & Axle Group 25 35 34 36 4 Cable goes thru #3 4 this page 1 16 30 32" Cut Mower HANDLE GR OUP SHEET 4 OF 4 R0303.1 3 9 33 22 19 22a 5 7 6 20 21 8 23 24 2 17 11 18 31 15 13 28 I N D A K 26 27 29 I N D A K 10 12[...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION 1 3023511 1 Handle assembly --- 3032136 1 Mower dash overlay decal 2 3031283 2 Handle grip - 1"dia x 4-1/2" 3 3031122 4 1/2-13 x 1-1/4" hex bolt 4 3032130 4 1/2-13 serrated flange nut 5 3023259 2 Brake handle 6 3031379 2 Handle grip [...]

GVTP SM32-R0303.1 Snapper 32” Cut Mower R0303.1 SHEET 4 - HANDLE GROUP REF # PART # QTY DESCRIPTION --- 3031916 1 5” jumper wire – 1/4” female spade to bullet terminal – engine kill --- 3031864 2 8" wire tie (secures harness to handlebar) --- 3032149 1 Multi-lead ground wire – to PTO switch, safety switch & off switch --- 30316[...]

GVTP SM32-R0303.1 32" Cut Mower HARNESS W IRING SCHEME 2-terminal male h ousing - Blade Clutch A - Not use d B - To 1/4" Female on Har ne ss C - To Ground le ad D-F - Not U se d G-H - To 2-terminal housing on Harn ess 1/4" female - PTO sw itch - locati on 'B' 1/4" m ale Bullet ter minal - engine kill 1/4" female 1[...]

GVTP SM32-R0303.1 McDonough, GA 30253 U.S.A.[...]