Sony ECM-3711 инструкция обслуживания

Part No. 2047371100R ECM-3711 Series VIA Eden V4 Micro Modul e User’s Manual 1 st Ed – 23 August 2006[...]

ECM-3711 Series 2 ECM-3711 Series User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULE S. OPERATION IS SUBJECT TO THE FOLLOWI NG TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CA USE UNDESIRED OPERATION. THIS EQUIPMENT HAS [...]

User’s Manual ECM-3711 Series User’s Manual 3 Disclaimer Evalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Evalue Technology a ssumes no responsibility or liability for the use of the d[...]

ECM-3711 Series 4 ECM-3711 Series User’s Manual Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your pr oduct documentation. These answers are normally a lot more detailed than th[...]

User’s Manual ECM-3711 Series User’s Manual 5 Product Warranty Evalue warrants to you, the orig inal purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any product s which have been repaired or altered by persons other than repair p[...]

ECM-3711 Series 6 ECM-3711 Series User’s Manual Contents 1. Getting St arted ............................................................................................................ 9 1.1 Safety Prec autions .................................................................................................... 9 1.2 Packing Li st ...............[...]

User’s Manual ECM-3711 Series User’s Manual 7 2.4.17 ATX Power Switch Co nnector (JPS1) ....................................................................................... 42 2.4.18 Power Connector (JPWR1)........................................................................................................ 42 2.4.19 Single Power Sele ct ([...]

ECM-3711 Series 8 ECM-3711 Series User’s Manual 1. CMOS BATTERY HAS FAILED ........................................................................................................ .9 1 2. CMOS CHECKSU M ERROR ............................................................................................................ .9 1 3. DISK BOOT FAILURE, INS[...]

User’s Manual ECM-3711 Series User’s Manual 9 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced el ectronics pe[...]

ECM-3711 Series 10 ECM-3711 Series User’s Manual 1.3 Document Amendment History Revision Date By Comment 1st Aug. 2006 Jason Liu Initial Release[...]

User’s Manual ECM-3711 Series User’s Manual 11 1.4 Manual Objectives This manual describes in detail the Ev alue Technology ECM- 3711 Single Board. We have tried to include as much informati on as possible but we have not duplicated information that is provided in the standard IB M Technical References, unless it proved to be necessary to aid i[...]

ECM-3711 Series 12 ECM-3711 Series User’s Manual 1.5 System Specifications System CPU Onboard VIA Eden V4 1 GHz BIOS Award 512 KB Flash BIOS System Chipset VIA CN700/VT8251 I/O Chip VIA VT1211 System Memory One 200-pin SODIMM supports up to 1 GB DDR2 400/533 SDRAM SSD One CompactFlash Type I/II socket Watchdog Timer Reset: 1~255 min. and 1 sec./s[...]

User’s Manual ECM-3711 Series User’s Manual 13 Mechanical & Environmental Power Requ irement +5 V @ 4.63 A, +12 V @ 0.53 A, 5 Vsb @ 0.32 A ( with VIA Eden V4 1 GHz & 1 GB DDR2 SDRA M) Power Type ATX Operation Temperature 0~60°C (32~140°F) Operating Humidity 0%~90% relative humidity, non-condensing Size ( L x W ) 45.7" x 4" ([...]

ECM-3711 Series 14 ECM-3711 Series User’s Manual 1.6 Architecture Overview 1.6.1 Block Diagram The following block diagram shows the arch itecture and main components of ECM-3721 Series. The following sections provide detail info rmation about the functions provided onboard.[...]

User’s Manual ECM-3711 Series User’s Manual 15 1.6.2 VIA CN700 & VT8251 The CN700 implements a deep In-Order Que ue to improve system performance for multi-threaded software applications. DBI and V4 bus protocol are supported which effectively reduce overall system power cons umption. The AGP controller is AGP v3.5 compliant with up to 2.1G[...]

ECM-3711 Series 16 ECM-3711 Series User’s Manual • 2D Graphics Engine The CN700 North Bridge's advanced 128-bit 2D graphics engine deliv ers high-speed 2D acceleration for productivity applications. T he enhanced 2D architecture with direct access frame buffer capability optimizes UMA performance and provides acceleration of all color dept[...]

User’s Manual ECM-3711 Series User’s Manual 17 The VT8251 interfaces to t he companion North Bridge ch ip through the Ultra V-Link interface with up to 1 GB/sec data transferra te. Two 1-Lane PCI Express ports are provided for high-speed peripheral devices. The VT8251 allows combining the two 1-Lane PCI-E ports into a 2-Lane port for peripheral[...]

ECM-3711 Series 18 ECM-3711 Series User’s Manual • Plug and Play functions wit h steerable PCI interrupts The PnP function allows complete steerability of PCI interrupts and integrated peripheral interrupts to system interrupt channel. One additional st eerable interrupt channel is provided to allow plug and play and re-configur ability of on-b[...]

User’s Manual ECM-3711 Series User’s Manual 19 1.6.4 VIA VT1636 LVDS Transmitter • Support Single / Dual LV DS Transmitter Function • Compatible with TI A/EIA-644 LVDS Standard • Supports LVDS 18-bit and 24-bit Output • Supports Dual Channel UXGA Panel Display • Supports 2D Dither for 18-bit Panel • Supports Option for 24-bit Color [...]

ECM-3711 Series 20 ECM-3711 Series User’s Manual A hardware monitor engine is built in to m onitor system health. An enhanced 8 bit ADC is built inside. This is exploited to simultaneou sly monitor 8 analog voltages or thermal inputs. The thermal inputs can be defined independently as thermistor or PentiumTM II thermal diode. Besides the ADC, the[...]

User’s Manual ECM-3711 Series User’s Manual 21 The device features next-generation PCI Express interconnect technology. PCI Express is a high-bandwidth, low pin count, serial, inte rconnect technology that offers significant improvements in performance over conventional PCI and also maintains software compatibility with existi ng PCI infrastruc[...]

ECM-3711 Series 22 ECM-3711 Series User’s Manual 2. Hardware Configuration[...]

User’s Manual ECM-3711 Series User’s Manual 23 2.1 Product Overview[...]

ECM-3711 Series 24 ECM-3711 Series User’s Manual 2.2 Installation Procedure This chapter explains you the instru ctions of how to setup your system. 1. Turn off the power supply. 2. Insert the DIMM module (be careful with t he orientation). 3. Insert all external cables for hard disk, flop py, keyboard, mouse, USB etc. except for flat panel. A CR[...]

User’s Manual ECM-3711 Series User’s Manual 25 2.2.1 Main Memory ECM-3711 series provides one 2 00-pin DIMM sockets to support DDR2 SDRAM. The total maximum memory size is 1GB. (Rear Side) Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the board a[...]

ECM-3711 Series 26 ECM-3711 Series User’s Manual • Locate the DIMM socket on the board. • Hold two edges of the DIMM module carefu lly. Keep away of touching its connectors. • Align the notch key on the m odule with the rib on the slot. • Firmly press the modules into the socket aut omatically snaps into the mounting notch. Do not force t[...]

User’s Manual ECM-3711 Series User’s Manual 27 2.3 Jumper and Connector List You can configure your board to match the needs of your applic ation by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect the[...]

ECM-3711 Series 28 ECM-3711 Series User’s Manual Connectors Label Function Note JAUDIO1 Audio connector 5 x 2 header, pitch 2.0mm JCD1 CD-ROM audio input connector 4 x 1 wafer, pitch 2.0mm JCF1 Compact Flash connector JCOM1 Serial port 1 connector D-sub 9-pin, male JCOM2 Serial port 2 connector 5 x 2 header, pitch 2.0mm JDIMM1 200-pin DDR2 SODIMM[...]

User’s Manual ECM-3711 Series User’s Manual 29 2.4 Setting Jumpers & Connectors 2.4.1 AT/ATX Power Select (JAT1) * Default AT* ATX 2.4.2 Clear CMOS (JCMOS1) * Default Protect* Clear CMOS[...]

ECM-3711 Series 30 ECM-3711 Series User’s Manual 2.4.3 Audio connector (JAUDIO1) Signal PIN PIN Signal GND 12 11 SPDIF OUT NC 10 9 NC Mic Bias 8 7 Mic-in LIN_R 6 5 LIN_L GND 4 3 GND LINEOUT _R 2 1 LINEOUT_L 2.4.3.1 Signal Description – Audio Connecter (JAUDIO1) Signal Signal Description LINEOUT L/R Left and right speaker out put. These are the [...]

User’s Manual ECM-3711 Series User’s Manual 31 2.4.4 CD-ROM Audio I nput Connector (JCD1) Signal PIN CD_L 4 GND 3 CD_R 2 GND 1 2.4.4.1 Signal Descript ion – CD-ROM Audio I nput Connecter (JCD1) Signal Signal Description CD_R Right CD-IN signal CD_L Left CD-IN signal. 2.4.5 Serial Port 1 Connector (JCOM1) Signal PIN PIN Signal GND 5 9 RI DTR 4[...]

ECM-3711 Series 32 ECM-3711 Series User’s Manual 2.4.5.1 Signal Description – Seri al Port 1 Connecter (JCOM1) Signal Signal Description TxD Serial output. This signal sends serial data to the communication link. The sign al is set to a marking state on hardwa re reset when the transmitter i s empty or when loop mode operation is initiated. RxD[...]

User’s Manual ECM-3711 Series User’s Manual 33 2.4.7 Serial Port Connector in RS-422 Mode (JCOM2) Signal PIN PIN Signal GND 10 9 GND RxD- 8 7 NC TxD+ 6 5 GND NC 4 3 NC RxD+ 2 1 TxD- 2.4.8 Serial Port Connector in RS-485 Mode (JCOM2) Signal PIN PIN Signal GND 10 9 GND NC 8 7 NC DATA+ 6 5 GND NC 4 3 NC NC 2 1 DATA-[...]

ECM-3711 Series 34 ECM-3711 Series User’s Manual 2.4.8.1 Signal Description – Seri al Port 2 Connecter (JCOM2) Signal Signal Description TxD Serial output. This signal sends serial data to the communication link. The sign al is set to a marking state on hardwa re reset when the transmitter i s empty or when loop mode operation is initiated. RxD[...]

User’s Manual ECM-3711 Series User’s Manual 35 2.4.9 General Purpose I/O Connector (JDIO1) Signal PIN PIN Signal GND 10 9 +5V GP17 8 7 GP13 GP16 6 5 GP12 GP15 4 3 GP11 GP14 2 1 GP10 2.4.9.1 Signal Description – Genera l Purpose I/O Connecter (JDIO1) Signal Signal Description GP [10:17] Digital Input/Output Data Bit 0 to Bit 8 2.4.10 System Fa[...]

ECM-3711 Series 36 ECM-3711 Series User’s Manual 2.4.11 Primary IDE Connector (JIDE1) Signal PIN PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 PDD9 PDD5 7 8 PDD10 PDD4 9 10 PDD11 PDD3 11 12 PDD12 PDD2 13 14 PDD13 PDD1 15 16 PDD14 PDD0 17 18 PDD15 GND 19 20 NC PDREQ 21 22 GND PDIOW# 23 24 GND PDIOR# 25 26 GND PIORDY 27 28 GND PDDACK# 29 30 GND [...]

User’s Manual ECM-3711 Series User’s Manual 37 2.4.11.1 Signal Description – Pr imary IDE Connector (JIDE1) Signal Signal Description PDA [2:0] IDE Address Bits. These address bits are used to access a regi ster or data port in a device on the IDE bus. DCS1#, DCS3# IDE Chip Selects. The chi p select signals are use d to select the command blo[...]

ECM-3711 Series 38 ECM-3711 Series User’s Manual 2.4.12 LCD Inverter Connector (JINV1) Signal PIN +12V 1 GND 2 ENBKL 3 VR 4 +5V 5 Note: For inverters with adjustable Backlight f unction, it is possible to control the LCD brightness through the VR signal controlled by JVR1 . Please see the JVR1 section for detailed circuitry information. 2.4.12.1 [...]

User’s Manual ECM-3711 Series User’s Manual 39 2.4.13 IrDA Connector (JIR1) Signal PIN IRTX 5 GND 4 IRRX 3 NC 2 +5V 1 2.4.13.1 Signal Description – IrDA Connector (JIR1) Signal Signal Description IRRX Infrared Receiver input IRTX Infrared Transmitter o utput[...]

ECM-3711 Series 40 ECM-3711 Series User’s Manual 2.4.14 PS/2 Keyboard & Mouse Connector (JKB1) Signal PIN PIN Signal MDAT 6 5 KDAT GND 4 3 +5V KCLK 2 1 MCLK 2.4.14.1 Signal Descript ion – PS/2 Keyboard & Mouse Connector (JKB1) Signal Signal Description KCLK Bi-directional clock signal used to strobe data/commands fro m/to the PC-AT keyb[...]

User’s Manual ECM-3711 Series User’s Manual 41 2.4.16 LVDS Connector (JLVDS1) Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.3V I 2 C_DAT 6 5 I 2 C_CLK GND 8 7 GND Txout0 10 9 Txout1 Txout0# 12 11 Txout1# GND 14 13 GND Txout2 16 15 Txout3 Txout2# 18 17 Txout3# GND 20 19 GND E_Txout0 22 21 E_Txout1 E_Txout0# 24 23 E_Txout1# GND 26 25 GND E_Txout[...]

ECM-3711 Series 42 ECM-3711 Series User’s Manual 2.4.17 ATX Pow er Switch Connector (JPS1) Signal PIN GND 2 PW_BN 1 2.4.18 Pow er Connector (JPWR1) PIN Signal 1 +12V 2 GND 3 GND 4 +5V[...]

User’s Manual ECM-3711 Series User’s Manual 43 2.4.19 Single Power Select (JSUS1) Signal PIN PWR_ON 1 +5V 2 VCCSB 3 Note: The default sets 2-3 closed for single power use d. 2.4.20 USB Connector 0, 1, 2 & 3 (JUSB1, JUSB2 ) Signal PIN PIN Signal +5V 1 2 GND D1-/D3- 3 4 GND D1+/D3+ 5 6 D0+/D2 + GND 7 8 D0-/D2- GND 9 10 +5V 2.4.20.1 Signal Des[...]

ECM-3711 Series 44 ECM-3711 Series User’s Manual 2.4.21 VGA Connector (JVGA1) Signal PIN Signal 6 GND RED 1 11 NC 7 GND GREEN 2 12 DAT 8 GND BLUE 3 13 HSYNC 9 VCC NC 4 14 VSYNC 10 GND GND 5 15 DCK 2.4.21.1 Signal Description – VGA Connecter (JVGA1) Signal Signal Description HSYNC CRT horizontal sync hro nisation output. VSYNC CRT vertical synch[...]

User’s Manual ECM-3711 Series User’s Manual 45 2.4.22 LCD Backlight Brightness Adjustment Connector (JVR1) Signal PIN +5V 3 VR 2 GND 1 VCC JINV1 pin 4 JVR1 1 2 3 Variation Resistor (Recommended: 4.7K  , >1/16W)[...]

ECM-3711 Series 46 ECM-3711 Series User’s Manual 2.5 Audio / USB Daughter Board User’s Guide 2.5.1 Jumper and Connector Layout 2.5.2 Jumper and Connector List Jumpers Label Function Note JP6 Line out / Speaker out select (The speaker out function is only available in combine used of main board) 1-3, 2-4 Speaker out 3-5, 4-6 Line out (Default) C[...]

User’s Manual ECM-3711 Series User’s Manual 47 2.5.3 Setting Jumper and Connector Line out / Speaker out Select (JP6) 2.54mm USB 1.1/2.0 Connector 1 (JP1) Line Out* Speaker Out Signal PIN PIN Signal +5V 1 2 GND D1- 3 4 GND D1+ 5 6 D2+ GND 7 8 D2- GND 9 10 +5V Note: Wrong USB cable configuration with your USB devices might cause your USB devices[...]

ECM-3711 Series 48 ECM-3711 Series User’s Manual 3. BIOS Setup[...]

User’s Manual ECM-3711 Series User’s Manual 49 3.1 Starting Setup The AwardBIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contai ned in the CMOS and begins the process of checking out the system and configuring it. W hen it finishes, the BIOS will seek an operating system on one of t[...]

ECM-3711 Series 50 ECM-3711 Series User’s Manual 3.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the PageUp and PageDown keys to change entries, pr ess <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program usi[...]

User’s Manual ECM-3711 Series User’s Manual 51 • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “ ¾ ” pointer marks all sub menus. 3.3 Getting Help Press F1 to pop up a small help window that de scribes the appropriate keys to use and the possible selections for the highl[...]

ECM-3711 Series 52 ECM-3711 Series User’s Manual 3.5 Main Menu Once you enter the AwardBIOS™ CMOS Set up Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Ent er> to accept and enter the sub-menu. N[...]

User’s Manual ECM-3711 Series User’s Manual 53 3.5.1 Standard CMOS Features The items in Standard CMOS Se tup Menu are divided into few categories. Each category includes no, one or more than one setup items. Use the arrow ke ys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. 3[...]

ECM-3711 Series 54 ECM-3711 Series User’s Manual 3.5.1.2 IDE Adapter Setup The IDE adapters control the ha rd disk drive. Use a s eparate sub menu to configure each hard disk drive. The below Figure will s hows the IDE primary master sub menu. Item Options Description IDE HDD Auto-detection Press Enter Press Enter to auto-detect the HDD on t his [...]

User’s Manual ECM-3711 Series User’s Manual 55 3.5.2 Advanced BIOS Features This section allows you to configure your system for basic oper ation. You have the opportunity to select the syst em’s default speed, boot-up seq uence, keyboard operation, shadowing and security. 3.5.2.1 CPU Feature This item allows you to select the CPU feature. It[...]

ECM-3711 Series 56 ECM-3711 Series User’s Manual 3.5.2.2 Hard Disk Boot Priority This item allows you to select the Hard Disk device boot up priority. Item Description Pri.Master Boot up from IDE Primary Master Hard Disk Pri.Slave Boot up from IDE Primary Slave Hard Disk Sec.Master Boot up from IDE Secondary Master Hard Disk Sec.Slave Boot up fro[...]

User’s Manual ECM-3711 Series User’s Manual 57 3.5.2.4 CPU L1 & L2 Cache This item allows you to enable the CPU L1 & L2 cache to speed up memory access. However, it depends on CPU design. Item Description Enabled Enable cache Disabled Disable cache 3.5.2.5 CPU L3 Cache This item allows you to enable the CPU L3 cache to speed up memory a[...]

ECM-3711 Series 58 ECM-3711 Series User’s Manual 3.5.2.11 Typematic Rate Setting Key strokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. Item Description Enabled Enable typematic rate/delay setting Disabled Disable typematic rate/delay setting 3.5.2.12 Typematic Rat[...]

User’s Manual ECM-3711 Series User’s Manual 59 3.5.2.18 Full Screen LOGO Show If the BIOS had the full screen logo in it, this item could allow enable/ disable the full screen logo show on display. Item Description Enable Enable full screen logo show Disable Disable full screen logo show 3.5.2.19 Small Logo (EPA) Show This item allows you enabl[...]

ECM-3711 Series 60 ECM-3711 Series User’s Manual 3.5.3 Advanced Chipset Features This section allows you to configure the system based on the specif ic features of the installed chipset. This chipset manages bus speeds and access to system memory resources, such as DRAM and the external ca che. It also coordinates communications between the conve[...]

User’s Manual ECM-3711 Series User’s Manual 61 3.5.3.1 DRAM Clock/Drive Control This section can set the DRAM clock/driver timing. Item Options Description DRAM Clock By SPD 100NHz 133 MHz 166 MHz 200 MHz 266 MHz Set the memory bus frequency to o perate at various values for the proper memory clo ck setting DRAM Timing Manual Auto By SPD Turbo [...]

ECM-3711 Series 62 ECM-3711 Series User’s Manual 3.5.3.2 AGP & P2P Bridge Control This item stores the onboard AGP and P2P functi on information. The reference table is as below. Item Options Description AGP Aperture Size 32M, 64M, 128M, 256M, 512M, 1G Select the size of Accele rated Graphics Port (AGP) aperture. The aperture is a porti on of[...]

User’s Manual ECM-3711 Series User’s Manual 63 3.5.3.3 CPU & PCI Bus Control Item Options Description PCI Master 0 WS Write Enabled Disabled To write PCI bus while zero wait state is executed. PCI Delay Transaction Enabled Disabled This feature is used to meet the latency of PCI cycles to and from the ISA bus. The ISA bus is much, much slow[...]

ECM-3711 Series 64 ECM-3711 Series User’s Manual 3.5.3.4 Memory Hole This feature allows you to create a memory hole. Item Description Disabled 512K-640K 15M-16M 14M-16M When this item is enabled, ISA ROM will be mapped to 15-16M area and also support legacy ISA devices. While this it em is disabled and legacy ISA devices are not utilized, the gr[...]

User’s Manual ECM-3711 Series User’s Manual 65 3.5.4 Integrated Peripherals Use this menu to specify your se ttings for integrated peripherals. 3.5.4.1 VIA OnChip IDE Device[...]

ECM-3711 Series 66 ECM-3711 Series User’s Manual Item Options Description SATA Controller Enabled Disabled The chipset contains a SATA IDE interface with support for two IDE channe ls. Select Enabled to activate the primary IDE interface (Channel0). Select Disabled to deactivate this interf ace. SATA Mode IDE RAID Setup the onboard SATA Mode. IDE[...]

User’s Manual ECM-3711 Series User’s Manual 67 3.5.4.2 VIA OnChip PCI Device Item Options Description AC97 Audio Controller Auto Disabled This item allows you to decide to enable/disable the VIA chi pset family to support AC97 Audio.[...]

ECM-3711 Series 68 ECM-3711 Series User’s Manual 3.5.4.3 Super IO Device Item Options Description Onboard Serial Port 1 Onboard Serial Port 2 Disable 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 AUTO Select an address and corre sponding interrupt for the first and second serial ports. COM Port 232/422/485 RS232 RS422 RS485 Select COM port type. Watch Dog [...]

User’s Manual ECM-3711 Series User’s Manual 69 3.5.4.4 USB Device Setting Item Options Description USB 1.0 Controller Enabled Disabled This item is to enable or disable the USB 1.0 Controller. USB 2.0 Controller Enabled Disabled This item is to enable or disable the USB 2.0 Controller. USB Operation Mode Full/Low Speed High Speed This item is t[...]

ECM-3711 Series 70 ECM-3711 Series User’s Manual 3.5.5 Power Management Setup The Power Management Setup allows you to conf igure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. 3.5.5.1 ACPI Function This item allows you to enable/disable the ACPI function. The choices: Enable[...]

User’s Manual ECM-3711 Series User’s Manual 71 3.5.5.5 Suspend Mode This setting defines the number of minutes before the system enters "suspend mode", the deepest level of system inactivity shutdown. The exact definition depends on the system, but in general this mode means that all system devices are shutdown (except for any that th[...]

ECM-3711 Series 72 ECM-3711 Series User’s Manual 3.5.5.12 Wakeup Event Detect Item Option Description PS2KB Wakeup Select Hot Key Password Allows you to select the method of PS2KB wake up PS2KB Wakeup Key Select Ctrl + F1~F1 2 Power Wake Any Key Allows you to set the key of PS2 keyboard wake up PS2KB Wakeup Key Select Any Button Left Button Right[...]

User’s Manual ECM-3711 Series User’s Manual 73 3.5.6 PnP / PCI Configuration This section describes configur ing the PCI bus system. PCI, or P ersonal C omputer I nterconnect, is a system which allows I/O dev ices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers s[...]

ECM-3711 Series 74 ECM-3711 Series User’s Manual 3.5.6.4 IRQ Resource When resources are controlled manually, a ssign each system interrupt a type, depending on the type of device using the interrupt. This item allows you to determine the IR Q assigned to the PCI bus or reserved. The Choices: PCI, Reserved. 3.5.6.5 PCI / VGA Palette Snoop Leave t[...]

User’s Manual ECM-3711 Series User’s Manual 75 3.5.7 PC Health Status This section shows the status of your CPU.[...]

ECM-3711 Series 76 ECM-3711 Series User’s Manual 3.5.8 Frequency / Voltage Control This menu specifies your setti ng for frequency/voltage control. 3.5.8.1 CPU Clock Ratio: This item allows you to select the CPU clock ratio. The choices: 6X 3.5.8.2 Auto Detect PCI Clk This item allows you to enable or disable detecting PCI clock automatically. Th[...]

User’s Manual ECM-3711 Series User’s Manual 77 3.5.9 Load Fail-Safe Defaults Use this menu to load the B IOS default values for the mini mal/stable performance for your system to operate. Press <Y> to load the BIOS default values for the most stable, minimal-performance system operations. 3.5.10 Load Optimized Defaults Use this menu to lo[...]

ECM-3711 Series 78 ECM-3711 Series User’s Manual 3.5.11 Set Supervisor / User Passw ord You can set either supervisor or user password, or both of them. Supervisor Password: able to enter/c hange the options of setup menus. User Password: able to enter but no right to change the options of setup menus. Type the password, up to eight characters in[...]

User’s Manual ECM-3711 Series User’s Manual 79 When a password has been enabled, you will be prom pted to enter it every time you try to enter Setup. This prevents an unauthorized per son from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time [...]

ECM-3711 Series 80 ECM-3711 Series User’s Manual 3.5.12 Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Enter <Y> to store the selection made in the menus in CMOS, a special section in memory that stays on after turning the system off. The BIOS configures the system according to the Setup selection stored in CMOS when [...]

User’s Manual ECM-3711 Series User’s Manual 81 4. Drivers Installation Note : Installation procedures and scr een shots in this section are for your reference and may not be exactly the same as shown on your screen.[...]

ECM-3711 Series 82 ECM-3711 Series User’s Manual 4.1 Install Chipset Driver (For VIA CN700) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_ChipsetVIACN700. Note: The installation procedure[...]

User’s Manual ECM-3711 Series User’s Manual 83 Step 6. Click Next . Step 7. Click Finish to restart the PC.[...]

ECM-3711 Series 84 ECM-3711 Series User’s Manual 4.2 Install Display Dri ver (For VIA CN700) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_DisplayVIACN700 . Note: The installation proced[...]

User’s Manual ECM-3711 Series User’s Manual 85 4.3 Install Audio Driver (For VIA VT1616) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_AudioVIAVT1616. Note: The installation procedures [...]

ECM-3711 Series 86 ECM-3711 Series User’s Manual 4.4 Install Ethernet Driver (For Realtek RTL8111B) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to D:Driver_GigabitRealtek RTL8111B . Note: The ins[...]

User’s Manual ECM-3711 Series User’s Manual 87 5. Measurement Drawing[...]

ECM-3711 Series 88 ECM-3711 Series User’s Manual (Unit: mm)[...]

User’s Manual ECM-3711 Series User’s Manual 89 Appendix A: BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Known Problems[...]

ECM-3711 Series 90 ECM-3711 Series User’s Manual Appendix B: AWARD BIOS POST Messages[...]

User’s Manual ECM-3711 Series User’s Manual 91 Overview During the Power On Self-Test (POST), if t he BIOS detects an error requiring you to do something to fix, it will either sound a beep code or display a message. If a message is displayed, it will be accompanied by: PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP Post Beep Currentl[...]

ECM-3711 Series 92 ECM-3711 Series User’s Manual 5. DISPLAY SWITCH IS SET INCORRECTLY Display switch on the motherboard can be set to either monochrome or co lor. This indicates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, and then either turn off the system and change the ju mper, or enter[...]

User’s Manual ECM-3711 Series User’s Manual 93 12. Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY The non-volatile memory containing EISA configuration information was programmed incorrectly or has become corrupt. Re-run EISA configuration utility to correctly program the memory. Note: When either of these errors appears, the [...]

ECM-3711 Series 94 ECM-3711 Series User’s Manual 20. PRESS A KEY TO REBOOT This will be displayed at the bottom screen when an error occurs that requires you to reboot. Press any key and the system will reboot. 21. PRESS F1 TO DISABL E NMI, F2 TO REBOOT When BIOS detects a Non-maskable Interrupt condition during boot, this will allow you to disab[...]

User’s Manual ECM-3711 Series User’s Manual 95 27. Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY The board ID does not match the ID stor ed in the EISA non-volatile memory. Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run t he EISA Configur ation Utility. 28. FLOPPY DISK(S) fail (8[...]

ECM-3711 Series 96 ECM-3711 Series User’s Manual 40. POST Codes POST (hex) Description CFh Test CMOS R/W functionality. C0h Early chipset initialization: -Disable shadow RAM -Disable L2 cache (socket 7 or below) -Program basic chipset registers C1h Detect memory -Auto-detection of DRAM size, type and ECC. -Auto-detection of L2 cache (socket 7 or [...]

User’s Manual ECM-3711 Series User’s Manual 97 POST (hex) Description 15h Reserved 16h Initial Early_Init _Onboard_Generator switch. 17h Reserved 18h Detect CPU information includ ing brand, SMI type (Cyrix or Intel) and CPU level (586 or 686). 19h Reserved 1Ah Reserved 1Bh Initial interrupts vector table. If no special specified, all H/W inter[...]

ECM-3711 Series 98 ECM-3711 Series User’s Manual POST (hex) Description 2Dh 1. Initialize multi-language 1. Put information on screen display, including Award title, CPU type, CPU speed …. 2Eh Reserved 2Fh Reserved 30h Reserved 31h Reserved 32h Reserved 33h Reset keyboard except Winbond 977 series Super I/O chips. 34h Reserved 35h Reserved 36h [...]

User’s Manual ECM-3711 Series User’s Manual 99 POST (hex) Description 51h Reserved 52h Test all memory (clear all extended memory to 0) 53h Reserved 54h Reserved 55h Display number of proce ssors (multi-processor platform) 56h Reserved 57h 1. Display PnP logo 2. Early ISA P nP initialization - A s s i g n C S N t o e v e r y I S A P n P d e v i[...]

ECM-3711 Series 100 ECM-3711 Series User’s Manual POST (hex) Description 73h (Optional Feature) Enter AWDFLASH.EXE if : -AWDFLASH is found in floppy drive. -ALT+F2 is pressed 74h Reserved 75h Detect & install all IDE dev ices: HDD, LS12 0, ZIP, CDROM….. 76h Reserved 77h Detect serial ports & parallel ports. 78h Reserved 79h Reserved 7Ah[...]

User’s Manual ECM-3711 Series User’s Manual 101 POST (hex) Description 94h 1. Enable L2 cache 1. Program boot up speed 2. Chips et final initialization. 3. Power management final initializ ation 4. Clear screen & display summary table 5. Program K6 write allocation 6. Program P6 class write combining 95h 1. Program daylight saving 1. Update[...]