Sony SLV-SE35EG инструкция обслуживания

Video Cassette Recor der ©1999 by Son y Cor poration SL V -SE35EG Operating Instructions 3-865-151- 12 (1) P AL NTSC 4.43[...]

Introduction 2 WARNING T o pr event fire or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to qualified a personnel only . Mains lead must only be changed at a qualified service shop. Precautions Safety • This unit operates on 220 – 240 V AC, 50 Hz. Check that the u[...]

3 Introduction T able of contents Getting Started * ShowV iew is a trademark applied for by Gemstar Development Corp. ShowV iew system is manufactured under license fr om Gemstar Development Corporation. Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the r emote commander 8 Step 3: Connecting the VCR 12 Step 4: T uning your TV to the VCR [...]

Getting Started 4 Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • R6 (size AA) batteries • Aerial cable[...]

5 Getting Started Getting Started Step 2 Setting up the r emote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Using the remote com[...]

Getting Started 6 Step 2 : Setting up the remote commander (continued) WIDE … TV/VIDEO I/ u DISPLA Y Á +/– Programme number buttons TV control buttons To T urn the TV into standby mode Select an input source of the TV either fr om aerial in or from line in Select the programme position of the TV Press I / u … TV/VIDEO Programme number button[...]

7 Getting Started Getting Started Notes • W ith normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, r emove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one together . • Do not use dif ferent types of [...]

Getting Started 8 Step 3 Connecting the VCR If your TV has a EURO-A V connector , see page 9. If your TV does not have a EURO-A V (Scart) connector : Signal flow AERIAL IN Aerial cable (supplied) AERIAL IN AERIAL OUT to mains 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. 2 Connect AERIAL OUT of[...]

9 Getting Started Getting Started If your TV has a EURO-A V (Scart) connector 1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. 2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable. : Signal flow AERIAL IN Aerial cable (supplied) AERIAL IN AERIAL OUT to ma[...]

Getting Started 10 3 Connect LINE-1 (TV) on the VCR and the EURO-A V (Scart) connector on the TV with the optional EURO-A V cable. This connection improves pictur e and sound quality . Whenever you want to watch the VCR picture, pr ess … TV/ VIDEO to display the VIDEO indicator in the display window . 4 Connect the mains lead to the mains. Note ?[...]

11 Getting Started Getting Started • TV Direct Rec Y ou can easily recor d what you are watching on the TV (other than tapes being played on this VCR). For details, see “Recording what you ar e watching on the TV (TV Direct Rec)” on page 39. • One T ouch Play W ith One T ouch Play , you can start playback automatically without turning on th[...]

Getting Started 12 Step 4 T uning your TV to the VCR If you have connected the VCR to your TV using the EURO-A V cable, skip this step. I/ u ON/ST ANDBY PROGRAM +/– RF CHANNEL 1 Press I / u ON/ST ANDBY to turn on the VCR. 2 Press RF CHANNEL on the VCR lightly . The factory-preset RF channel appears in the display window . The VCR signal is output[...]

13 Getting Started Getting Started 5 Press PROGRAM +/– (r epeatedly) to select the appropriate TV system for your ar ea. Select “G” for the B/G TV system, or “K” for the D/K TV system. 6 T une the TV to the same channel as that shown in the display window so that the picture on the right appears clearly on the TV screen. Refer to your TV [...]

Getting Started 14 Step 5 Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. W ith this function, you can set the language for the on-screen display , TV channels, guide channels for the ShowV iew system. AUTO SET UP 1 Hold down AUTO SET UP on the VCR for mor e th[...]

15 Getting Started Getting Started 3 Press AUTO SET UP lightly . The VCR starts searching for all of the r eceivable channels and presets them accor ding to the TV system you selected in “T uning your TV to the VCR.” If you use the SMAR TLINK connection, the Preset Download function starts and the SMAR TLINK indicator flashes in the display win[...]

Getting Started 16 Setting the clock Y ou must set the time and date on the VCR to use the timer recor ding features properly . The Auto Clock Set function works only if a station in your area is br oadcasting a time signal. If the Auto Set Up function did not set the clock correctly for your local area, try another station for the Auto Clock Set f[...]

17 Getting Started Getting Started 3 Press > / . to highlight MANUAL ADJUST , then press OK. 4 Press > / . to set the date. 5 Press / to highlight the month and set the month pr essing > / . . 6 Set the year , hour , and minutes in sequence, pressing / to highlight the item to be set, and press > / . to select the digits. The day of the[...]

Getting Started 18 Step 6 : Setting the clock (continued) 7 Press OK to start the clock. 8 Press MENU to exit the menu. Tips • T o change the digits during setting, press ? to return to the item to be changed, and select the digits pressing > / . . • If you want to r eturn to the previous menu, highlight RETURN and press OK. Note • The men[...]

19 Getting Started Getting Started 1 Press MENU, then pr ess > / . to highlight SETTINGS and press OK. 2 Press > / . to highlight CLOCK, then press OK. AUTO ADJUST is highlighted. 3 Press OK. Changing the station for the Auto Clock Set function Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel. continue[...]

Getting Started 20 4 Press > / . to highlight ON, then pr ess OK. 5 Press . to highlight CLOCK PROG, then press OK. 6 Press > / . r epeatedly until the programme position of the station that carries the time signal appears. If the VCR does not receive the time signal from any station, AUTO ADJUST returns to OFF automatically . 7 Press MENU to[...]

21 Getting Started Getting Started Selecting a language Y ou can change the on-screen display language from the one you selected with the Auto Set Up function. Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel. 1 Press MENU, then pr ess > / . to highlight SETTINGS and press OK. 2 Press > / . to highligh[...]

Getting Started 22 Pr esetting channels If some channels could not be preset using the Auto Set Up function, you can preset them manually . Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel. PROG +/– > / . / ? / / OK MENU 1 Press MENU, then pr ess > / . to highlight SETTINGS and press OK. 2 Press >[...]

23 Getting Started Getting Started Selected programme position 3 Press > / . to highlight NORMAL/ CA TV , then press OK. 4 Press > / . to highlight NORMAL, then press OK. T o preset CA TV (Cable T elevision) channels, select CA TV . 5 Press PROG +/– to select the pr ogramme position. 6 Press > / . to highlight CHANNEL SET , then pr ess O[...]

Getting Started 24 Presetting channels (continued) MENU 7 Press > / . r epeatedly until the channel you want is displayed. The channels appear in the following order: B/G TV system Channel number in the CHANNEL SET field C02 E2 C02 R1 C03 E3 C05 R6 C04 E4 C06 R7 C05 E5 C12 R12 C06 E6 C13 R2 C07 E7 C14 R3 C08 E8 C15 R4 C09 E9 C16 R5 C10 E10 C17 R[...]

25 Getting Started Getting Started Disabling unwanted programme positions After presetting channels, you can disable unused pr ogramme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. 1 In step 7 above, press pr ogramme number button “0” twice to display the number “00” beside CHANNEL SET . 2 Pr[...]

Getting Started 26 1 Press MENU, then pr ess > / . to highlight LISTS and press OK. 2 Press > / . to highlight CHANNEL LIST , then press OK. Changing/ disabling pr ogramme positions After setting the channels, you can change the programme positions and station names as you like. If any programme positions ar e unused or contain unwanted chann[...]

27 Getting Started Getting Started 3 Press > / . to highlight the row on which you want to change the programme position, then pr ess / . T o display other pages for programme positions 6 to 60, press > / . repeatedly . 4 Press > / . until the selected channel row moves to the desired pr ogramme position. The selected channel is inserted a[...]

Getting Started 28 Changing/disabling programme positions (continued) 1 Press MENU, then pr ess > / . to highlight LISTS and press OK. 2 Press > / . to highlight CHANNEL LIST , then press OK. Changing the station names Y ou can change the station names (up to 5 characters). Before you start… • T urn on the VCR and the TV . • Set the TV [...]

29 Getting Started Getting Started 3 Press > / . to highlight the r ow on which you want to change the station name, then press / . T o display other pages for programme positions 6 to 60, press > / . repeatedly . 4 Press / . 5 Enter the station name. 1 Press > / . to select a character . Each time you pr ess > , the character changes a[...]

Getting Started 30 Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. Before you start… • T urn on the VCR and the TV . • Set the TV to the video channel. CLEAR 1 Press MENU, then pr ess > / . to hi[...]

31 Getting Started Getting Started 2 Press > / . to highlight CHANNEL LIST , then pr ess OK. 3 Press > / . to highlight the row on which you want to disable. 4 Press CLEAR. The selected row will be clear ed as shown on the right. 5 Repeat steps 3 and 4 for any other programme positions you want to disable. 6 Press MENU to exit the menu. Tip ?[...]

Basic Operations 32 Basic Operations Playing a tape 6 EJECT 1 T urn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. DISPLA Y · PLA Y P P AUSE )# FF p STOP 03 REW NTSC PB CLEAR 123 456 789 0[...]

Basic Operations Basic Operations 33 Set NTSC PB to ON P AL TV NTSC 4.43 Additional tasks To Stop play Pause play Resume play after pause Fast-forward the tape Rewind the tape Eject the tape Press p STOP P P AUSE P P AUSE or · PLA Y )# FF during stop 03 REW during stop 6 EJECT T o set the colour system If the playback picture has no colour , or st[...]

Basic Operations 34 Notes • The counter r esets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no r ecording. • The time counter does not appear on the TV scr een when using an NTSC-recorded tape. • Depending on your TV , the following may occur while playing an NTSC-recor ded ta[...]

Basic Operations Basic Operations 35 Recor ding TV pr ogrammes r REC PROG +/– SP/LP 1 T urn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place. INPUT SELECT COUNTER/REMAIN DISPLA Y … TV/VIDEO p STOP continued 123 456 789 0[...]

Basic Operations 36 Recording TV pr ogrammes (continued) 3 Press INPUT SELECT until a pr ogramme position number appears in the display window . 4 Press PROG +/– to select the pr ogramme position you want to recor d. 5 Press SP/LP to select the tape speed, SP or LP . LP (Long Play) provides r ecording time twice as long as SP , however , SP (Stan[...]

Basic Operations Basic Operations 37 Safety tab T o check the remaining time Press DISPLA Y . W ith the display on, press COUNTER/REMAIN to check the remaining time. Each time you pr ess COUNTER/REMAIN, the time counter and the remaining time appear alternately . The remaining time with the indicator also appears in the display window . T o correct[...]

Basic Operations 38 Recording TV pr ogrammes (continued) Tips • T o select a programme position, you can use the programme number buttons on the remote commander . For two-digit numbers, press the ? (ten’s digit) button followed by the programme number buttons. • Y ou can select a video source fr om the LINE-1 (TV) connector also using the IN[...]

Basic Operations Basic Operations 39 Recording what you ar e watching on the TV (TV Direct Rec) If you use the SMAR TLINK connection, you can easily record what you ar e watching on the TV (other than tapes being played on the VCR). 1 Insert a tape with its safety tab in place. 2 Press r REC while you are watching a TV pr ogramme or external source[...]

Basic Operations 40 1 Press TIMER. • When you set TIMER OPTIONS to V ARIABLE The TIMER METHOD menu appears on the TV screen. Pr ess > / . to select SHOWVIEW , then press OK. • When you set TIMER OPTIONS to SHOWVIEW The SHOWVIEW menu appears on the TV screen. Recor ding TV pr ogrammes using the ShowV iew system The ShowV iew system is the fea[...]

Basic Operations Basic Operations 41 2 Press the pr ogramme number buttons to enter the ShowV iew number . If you make a mistake, press CLEAR and re-enter the corr ect number . 3 Press OK. The date, start and stop times, programme position, tape speed, and VPS/PDC setting appear on the TV screen. • If “--” appears in the “PROG.” (programm[...]

Basic Operations 42 Recording TV pr ogrammes using the ShowV iew system (continued) T o stop recording T o stop the VCR while recor ding, press p ST OP . Daily/weekly recor ding In step 4 above, press . to select the r ecording pattern. Each time you pr ess . , the indication changes as shown below . Press > to change the indication in reverse o[...]

Basic Operations Basic Operations 43 Timer recor ding with VPS/PDC signals Some broadcast systems transmit VPS (V ideo Programme System) or PDC (Programme Delivery Contr ol) signals with their TV programmes. These signals ensure that your timer r ecordings are made r egardless of broadcast delays, early starts, or broadcast interruptions (with the [...]

Basic Operations 44 1 Press TIMER. • When you set TIMER OPTIONS to V ARIABLE The TIMER METHOD menu appears on the TV screen. Pr ess > / . to select ST ANDARD, then pr ess OK. • When you set TIMER OPTIONS to ST ANDARD The TIMER menu appears on the TV screen. MENU Setting the timer manually If the ShowV iew system is not available in your area[...]

Basic Operations Basic Operations 45 2 Set the date, start and stop times, programme position, tape speed, and VPS/PDC function: 1 Press / to highlight each item in turn. 2 Press > / . to set each item. T o correct a setting, pr ess ? to return to that setting and reset. • T o recor d the same programme every day or the same day every week, se[...]

Basic Operations 46 Daily/weekly recor ding In step 2 above, press . to select the r ecording pattern. Each time you pr ess . , the indication changes as shown below . Press > to change the indication in reverse or der . Tips • T o set the programme position, you can also use the PROG +/– or programme number buttons. • T o set the tape spe[...]

47 Additional Operations Additional Operations Playing/sear ching at various speeds Playback options V iew the picture during fast-forward or r ewind Play at high speed × 2 & SLOW )# FF · PLA Y Operation During fast-forward, hold down )# FF . During rewind, hold down 03 REW . • During playback, pr ess )# FF or 03 REW on the remote commander[...]

Additional Operations 48 T o resume normal playback Press · PLA Y . Tip • Adjust the pictur e using the TRACKING +/– buttons if: – Streaks appear while playing in slow motion. – Bands appear at the top or bottom while pausing. – The picture shakes while pausing. T o set tracking to the centre position, press both buttons (+/–) at the s[...]

49 Additional Operations Setting the recor ding duration time After starting recor ding in the normal way , you can have the VCR stop recor ding automatically after a specified duration. 1 While recor ding, press r REC. The indicator appears in the display window . 2 Press r REC repeatedly to set the duration. Each press advances the time in incr e[...]

Additional Operations 50 1 Press I / u to turn on the VCR. 2 Press MENU, then pr ess > / . to highlight LISTS and pr ess OK. 3 Press > / . to highlight TIMER LIST , then press OK: • If you want to change or cancel a setting, go on to the next step. • If you do not need to change or cancel the settings, press MENU, then turn of f the VCR t[...]

51 Additional Operations Programme 1 Programme 2 Programme 1 Programme 2 about 20 seconds will be cut off will be cut off 4 Press > / . to select the setting you want to change or cancel, then press OK. The selected setting appears in the TIMER menu. 5 • T o change the setting, press ? / / to highlight the item you want to change, and press &g[...]

Additional Operations 52 Sear ching using the Smart Sear ch function If you recor d multiple programmes on a tape, use the Smart Sear ch function to see what has been recor ded on your tape. Y ou can see information such as date, time, and channel of programmes recor ded on a tape. Y ou can also start playback directly fr om the selected programme [...]

53 Additional Operations T o stop searching Press p ST OP . T o exit the SMART SEARCH screen Press SMAR T SEARCH. T o record in a blank space Blank space on the tape will appear as a blank row in the SMAR T SEARCH screen. Select the blank r ow in step 3, then press OK. The VCR r ewinds/ fast-forwards the tape to the beginning of the blank space, th[...]

Additional Operations 54 Searching using the Smart Sear ch function (continued) AB C AD C Notes • If you begin r ecording a programme “D” from the middle of a pr eviously recorded programme “A” and into another pr eviously recorded programme “B,” the Smart Search information for the second pr ogramme “B” which is recorded over is [...]

55 Additional Operations Adjusting the pictur e Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window , then goes off), distortion may occur if the tape was recor ded in poor condition. In this case, manually adjust the tracking. During playback, press TRACKING +/[...]

Additional Operations 56 Tip • T o set tracking to the centre position, press the TRACKING + and – buttons at the same time. Notes • Y ou can adjust the tracking for the NTSC-recor ded tape but the tracking meter won’t be displayed. • W ith the Auto Long Play function on, the OPC function will work only in SP mode. If the tape speed autom[...]

57 Additional Operations Changing menu options 1 Press MENU, then select OPTIONS and press OK. 2 Press > / . to highlight OPTIONS-1 or OPTIONS-2, then pr ess OK. 3 Press > / . to select the option, then pr ess OK. 4 Press > / . to change the setting, then press OK. 5 Press MENU to r eturn to the original screen. continued SET : SELECT : OK[...]

Additional Operations 58 Menu option OPC AUTO LONG PLA Y T APE LENGTH COLOUR SYSTEM Set this option to • ON to switch on the OPC (Optimum Picture Contr ol) function and improve pictur e quality . • OFF to switch of f OPC. • ON to change the timer r ecording tape speed automatically to the LP mode when the r emaining tape becomes shorter than [...]

59 Additional Operations Menu option TIMER OPTIONS POWER SA VE RF MODULA TOR TV DIRECT REC Note • When you set a timer r ecording, the indicators in the display window remain on, even though POWER SA VE is set to ON. Set this option to • V ARIABLE to display the TIMER METHOD menu for selecting ST ANDARD or SHOWVIEW when pressing TIMER button. ?[...]

Additional Operations 60 Editing with another VCR How to connect to recor d on this VCR This VCR (Recorder) TV : Signal flow EURO-AV (Scart) : LINE-1 (TV) Other VCR (Player) EURO-AV cable (not supplied)[...]

61 Additional Operations Operation (when recor ding on this VCR) Before you start editing • T urn on your TV and set it to the video channel. • Press INPUT SELECT to display “L1” in the display window . • Press SP/LP to select the tape speed, SP or LP . 1 Insert a sour ce tape with its safety tab removed into the other (playback) VCR. Sea[...]

62 Additional Information Clock T roubleshooting If you have any questions or problems not cover ed below , please consult your nearest Sony service facility . Additional Information Symptom The I / u ON/ST ANDBY switch does not function. The power is turned on but the VCR does not operate. The clock has stopped and “–:– –” lights in the [...]

63 Additional Information Recording Symptom The picture is no colour . The picture r olls vertically during picture sear ch. The picture has no sound. No TV programme appears on the TV screen. TV reception is poor . The tape starts playing as soon as it is inserted. The tape is ejected when you press r REC. Nothing happens when you press r REC. The[...]

64 Additional Information Symptom A tape cannot be inserted. The remote commander does not function. The SMAR TLINK function does not work. The tracking meter does not appear on the TV screen. The VCR needs to be cleaned. Others Remedy • Check that a tape isn’t alr eady in the tape compartment. • Make sur e you are pointing the remote command[...]

65 Additional Information Specifications System Channel coverage P AL (B/G, D/K) VHF E2-E12, R1-R12 UHF E21-E69, R21-R69 CA TV S1-S41, S01-S05 RF output signal UHF channels 21 to 69 Aerial out 75-ohm asymmetrical aerial socket Inputs and outputs : LINE-1 (TV) 21-pin V ideo input: pin 20 Audio input: pins 2 and 6 V ideo output: pin 19 Audio output: [...]

66 Additional Information Index to parts and contr ols Refer to the pages indicated in parentheses ( ) for details. Front panel 8 p STOP button (33, 61) 9 P P AUSE button (33, 61) !º PROGRAM/TRACKING +/– buttons (14, 48, 55) !¡ AUTO SET UP/ RF (Radio Frequency) CHANNEL button (12, 14) !™ Remote sensor (5) 1 I / u ON/ST ANDBY switch/ indicator[...]

67 Additional Information Display window 1 T imer indicator (42, 45) 2 T ape speed indicators (36) 3 VIDEO indicator (10, 37) 4 VPS (V ideo Programme System)/ PDC (Programme Delivery Contr ol) indicator (43) 5 OPC (Optimum Picture Contr ol) indicator (55) 6 SMAR TLINK indicator (10) 7 TV indicator (39) 8 Tracking indicator (55) 9 T ime counter/cloc[...]

68 Additional Information Index to parts and controls (continued) Rear panel 1 Mains lead (8, 9) 2 AERIAL IN ANTENNE ENTREE connector (8, 9) 3 AERIAL OUT ANTENNE SOR TIE connector (8, 9) 4 NTSC PB (Play Back) switch (33) 5 : LINE-1 (TV) : LIGNE-1 (TV) connector (10, 60)[...]

69 Additional Information Remote commander 1 6 EJECT button (33) 2 COUNTER/REMAIN button (37) 3 CLEAR button (41, 51) 4 SP (Standar d Play)/LP (Long Play) button (36) 5 Programme number buttons (6, 38) 6 ? (ten’s digit) button (6, 38) 7 . (volume) +/– buttons (for TV) (7) 8 r REC (recor d) button (36, 49) 9 TIMER button (40, 44) 0 MENU button ([...]

70 Additional Information !™ TV / VIDEO remote contr ol switch (5) !£ I / u (on/standby) switch (6, 42) !¢ INPUT SELECT button (36, 45, 61) !∞ … TV/VIDEO button (6, 37) !§ DISPLA Y button (37) !¶ PROG (programme) +/– buttons (6, 23, 36) !• WIDE button ( for TV ) (7) !ª & SLOW button (48) @º × 2 button (48) @¡ SMAR T SEARCH but[...]

[...]

A, B Adjusting picture 25, 55 tracking 55 Aerial hookup 8 AFT (Auto Fine T uning) 25 Auto Clock Set 19 Auto Set Up 14 Auto Long Play 58 C Changing the programme position 26 Changing the station name 28 Cleaning the video heads 62 Clock setting 16 Colour system compatible colour systems 2 setting 33 Connecting the VCR and your TV 8 to a TV with a EU[...]