Spirit IN839 инструкция обслуживания

PLEASE CARE FULL Y READ THIS ENTIRE MANUAL BEFORE OPERATING Y OUR NEW TREADMILL! Z100 / Z300 Z500 Z700 B Y OW NER’S MANUA L[...]

IN839 1 Product Registratio n………………………………… …………………………… …………. 2 Important S afety Instructions………… ………………………………………… …………… 3 Important E lectrical Information……… ………………………………………… ……………4 Important Op[...]

IN839 2 Thank you for your purchase of this q ualit y treadmill fr om Spirit Manufa cturing, Inc. Your ne w tread mill was ma nufacture d by one of the lea ding fitne ss manufacturers in th e world an d is ba cked by one of the most compreh ensive warranties a vailable. T hrough your dealer, Spirit will do all we can to m ake your ownership e xperi[...]

IN839 3 WARNING - Read a ll instructions be fore using this appliance . DANGER - To reduc e the risk of electri c shock, disconnec t y ou r Spirit tre admill from the electric al outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns , fire, electric s hock, or injury to persons, install the treadmill on a flat level su[...]

IN839 4 fatigue. Remove tether cord a fter use to p revent unauthorized trea dmill operation. SAVE THESE I NSTRUCTIONS - THINK S AFETY! WARNING! NEVER use a ground fault circuit interrupt (GFCI) wall outlet with th is treadmill. Route the po wer cord away from any mo ving part of the treadmill includin g the elevation mechanism and transport wheels[...]

IN839 5 NEVER opera te this treadmill without reading and completely understa nding the results of an y operational change you request from the com puter. Understand that changes in spee d and incline do not occur imm ediately. Set your desired spe ed on the compute r console and release the adjus tment key. The compute r will obey the command grad[...]

IN839 6 Stop / Pause switch in normal opera tion. ASSEMB L Y P ACK CHE CK LIS T (IN83 9) 5/16"x 1/2" B utton Head Socket Screw (x2) 5/16"x 3/4" B utton Head Socket Screw (x2) 5/16"x 1-1/2" But ton Head Socket Scre w (x2) 5/16"x 19 x1.5T Curve Washer (x 2) M5 x 10 mm Button Head Socke t Screws (x4) Safety Ke y (x1)[...]

IN839 7 Install the console into the Console Support with 4 pcs of M5 x 10 mm Button Head Socket Screws by using th e Combinatio n M5 Allen Wrench & Screwdriver . (As shown in f igure 5.) ■ PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIE S HAVE BEEN ASSEMBLED. Assem bly Ins truction s (IN83 9)[...]

IN839 8 Do not attemp t to move the unit unless it is in the folded an d locked position. Be sure the power cord is se cured to avoid possib le damage. Use both ha ndrails to maneu ver the unit to the desired position. ■ To Fold The Treadmill: Pull the locking knob with l eft hand, right hand lift t he running deck up to 30cm t hen two hands lift[...]

IN839 9 Getting familiar with the control pan el ■ IN839 Console WINDOW DISPLA Y : SPEED: Displays the cu rrent running speed f rom 0.8Mph- 6Mph. TIME: Accumulates t otal workout time from 00:00 to 99 :59. DIST ANCE : Accumulates t otal workout distance from 0.00 to 99.99 miles. CALORIES : Accu mulates the u ser ’s calorie consumpt ion during e[...]

IN839 10 999.9 ca lories. PULSE: Displays your current hea rt rate in beats per minute during workout f rom 40 to 220. INCLINE: Displa ys your current workout elevation from 0 to 15 . FUNCTION BUTT ONS: ST ART : Press “ST ART” button to start training. STOP: Pre ss “STOP” button to stop trainin g. F A ST : Press “F A ST’ button to incre[...]

IN839 1 1 ERROR MESSA GE: ERR: T readmill doesn’t re ceive the speed signal for 6 seconds o r controller fault then treadmill will stop. Re start the treadmill after fix ing the problem. Belt and Bed - Your treadmill uses a very high-eff icient low-friction bed. Performan ce is maximized when t he bed is kept as cle an as possible. Use a sof t, d[...]

IN839 12 Tighten the re ar roller only enou gh to prevent slippage at the f ront roller. Turn the treadbelt ten sion adjusting bolt in incremen ts of 1/4 turn and inspec t for proper tension. When an adjustment is made to the belt tension, y ou must a lso mak e a tracking adjustment to compe nsate for the change in belt tens ion. This is accomplish[...]

IN839 13 middle po rtion (away from edges) of the deck (und er treadbelt) along its w idth . When walked on, the belt will make certain an e ven coat is applied. Lub ricant is not harmful t o the skin. Lub e will be distributed properly by walking at 2 to 3 mph for 3 to 5 m inutes on all areas of the belt. Use handra ils for support. The first few [...]

IN839 14 touched ( on a cold da y)while w alking/run ning T readmill is not grounde d. Static e lectricit y is “crashing” the com puter. Refer to Groundin g Instructions on page 4. Effective October 15, 20 04 TREAD MILL W ARRANTY Spirit Manufacturing Inc. w arrants all its treadmills’ parts for a period of 2 years from the date of reta il sal[...]

IN839 15 freight damage claims with the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER . All units arriving without a return autho rization number will be refused. 5. For any further infor mati on, or t o contact our service department by mail, send your corresponden ce to: Spirit Manufacturin[...]