StarTech.com ARMDUAL инструкция обслуживания

Manual Revision: 06/16/2014 For the most up-to-date information, please visit: www.startech.com ARMDU AL Desk Mount Ar ticulating Dual Monitor Arm with Cable Management & Height A djust *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr .startech.com ES: Guía del usuario - es.sta[...]

Instruction Manual FCC C ompliance Statemen t This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules . These limits ar e designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates , uses and can radiate[...]

Instruction Manual i T able of C ontents Introduction ............................................................................................ 1 Packaging Conten ts ................................................................................................................................. 1 Product Diagram .................................[...]

Instruction Manual 1 Introduction Packaging C ontents[...]

Instruction Manual 1 P roduct Diagram[...]

Instruction Manual 2 Installation W ARNING! It is the installer ’ s responsibility to ensure that the combined w eight of all components does not exc eed the maximum weight capacity 13.6 kg (30 lbs) of the mounting arm. Con verting the Desk Clamp to a Grommet Clamp The Dual Monitor Arm can be clamped to a desk / table, or mounted thr ough a gromm[...]

Instruction Manual 3 3. Using the 4 hex screw s removed in Step 2, install the Grommet Pla te (7) to the base of the pole. 4. Remove the screw and 2 w ashers shown using a Phillips screwdriver to disconnect the threaded shaft from the base of the clamp, then slide the plat e back onto the shaft. Finished Gr ommet Clamp:[...]

Instruction Manual 4 Desk / Grommet Mounting 1. Adjust the height of the Desk Clamp (3) to t y our desk sur face (if applicable). 2. Place the 4 Plastic Gasket Cushions (13) as sho wn.[...]

Instruction Manual 5 3. Desk Clamp: Place the Desk Clamp (3) opening around the edge of y our desktop in your desired location and tigh ten by hand to secure. Ensure tha t the Desk Clamp is making full contact with the desk sur face. 4. Loosen the collar on the support post and adjust to the desired height. Grommet Clamp: Place the base of the unit[...]

Instruction Manual 6 5. Slide the DEK (12) onto the support post so that it rests on the collar . Once adjusted to the desired height, tight en into place using the 2.5mm Allen Wrench (10). Attaching the Display s 1. Car efully place your display face down on a protective surface to access the mounting points. 2. Depending on the depth of the mount[...]

Instruction Manual 7 3. Using a Phillips screw driver , tighten the screws until the bracket is rmly attached to the back of the display . W ARNING! Do not over-tighten the scr ews and stop immediately if you encounter resistance to av oid damage to your display . Ensure that all spacers and screws being used are the same length and thread type.[...]

Instruction Manual 8 Attaching the L CD Arm Assembly 2. Tighten the set scr ew using the 2.5mm Allen W rench ( 10 ). 1. Slide the L CD Arm Assembly ( 1 or 2 ) down onto the DEK ( 12 ).[...]

Instruction Manual 9 3. Place the Co ver (11) over the mounting post and insert 1 x M6x12mm Phillips Screw (16) with 1 x Plastic Washer (15) . Tighten using a Phillips screwdriver . 4. Repeat for the other side .[...]

Instruction Manual 10 Cable Management Note: When attaching cables and routing thr ough the cable management channels, ensure that you leav e enough slack to avoid stretching / pulling out the cables when moving the arm. 1. Connect your cables to y our displays and position the mounting arm in its fully extended position to ensure that the cables y[...]

Instruction Manual 11 Adjusting L CD Arm Resistance W ARNING! For ced movement of the L CD Arms or Mount Brackets without loosening the screws may damage the pr oduc t or the mounted displays . Always support your display from underneath when making any adjustments to the L CD Arms or Mount Brackets to avoid damage to the display . Note: F or all a[...]

Instruction Manual 12 T o increase / decrease the pan / swing resistance, adjust the set scr ew located on the top of the Mount Bracket joint, using the 4mm Allen Wrench (9). T o increase / decrease the swivel resistance on either of the elbow join ts of the articulating LCD Arms, adjust the set scr ews indicated below , using the 2.5mm Allen Wrenc[...]

Instruction Manual 13 Specications W eight Capacity 30 lbs (13.6 kg) Max Display Size 24” VESA Compatibility 75x75 mm and 100x100 mm Maximum Extension 18.66 in (474 mm) Maximum Mounting Surface Thickness 3 in (75 mm)[...]

Instruction Manual 14 T echnical Suppor t StarT ech.com ’ s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your pr oduct, visit ww w .startech.com/suppor t and access our comprehensive selection of online tools , documentation, and downloads. For the la test drive[...]

Hard-to-nd made easy . At StarT ech.com, that isn’t a slogan. It’ s a promise. StarT ech.com is your one-stop source for every connectivity par t you need. Fr om the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions. We make it easy t o locat[...]