Strong PrimaSat II инструкция обслуживания

D i g i t a l S a t e l l i t e R e c e i v e r P r i m a S a t I I User manual[...]

[...]

[...]

PART 1 • English 1 English STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23EC; RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All product n[...]

PART 1 • English 2 1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INST ALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:   T o direct sunlight or near any other equipment that g[...]

PART 1 • English 3 English 1.3 Equipment Set-up W e recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below:   Refer to the user manual of your TV and your antenna.   Make sure that the SCART cable and outdoor components are in a good condition and the SCART connection i[...]

PART 1 • English 4 2. TV SCART T o connect to your TV set using a SCART cable. 3. S/PDIF COAX T o connect to the input of your digital audio amplifier . 4. Power Cord Y our receiver requires a mains voltage of 100~240 V AC (Auto- selectable), 50/60 Hz ±5%. Make sure to check the power specification before connecting your receiver to the wall o[...]

PART 1 • English 5 English 2.6 Using the Remote Control Fig. 4 T o use the remote control, point it towards the front of the digital receiver . The remote control has a range of up to 7 metres from the receiver at an angle of up to 60 degrees. The remote control will not operate if its path is blocked. NOTE: Sunlight or very bright light will dec[...]

PART 1 • English 6 4.1.4 Auto Standby This option allows you to enable Auto Standby or to disable Auto Standby . Auto Standby will switch the receiver to standby automatically when it doesn’t receive commands from the remote control for a period of 3 hours. T o avoid the automatic switch off, use tu to set Auto Standby to OFF . 4.1.5 Auto Time [...]

PART 1 • English 7 English Select the RED button to Set W est Limit position you have reached. Select the GREEN button to Set East Limit position you have reached. d) Satellite positions Press pq to select the Position you like to use and press OK . Press the RED button to Add SA T you like to install. Select a transponder receivable at your loca[...]

PART 1 • English 8 5.1 TV Press tu to move to Main Menu . In Main Menu press tu to move to TV and press OK to enter the TV menu. 5.1.1 TV Channels Use tu to reach the following sub-menus F av , Lock , Edit , Move , Sort , Skip , Delete and Search . With the BLUE button you can change the available group you would like to use. ( All Satellite, Sat[...]

PART 1 • English 9 English 5.1.1.7 Delete Press tu to select , then press pq to select the desired channel and OK to delete this channel. Press the YELLOW button to save and confirm or exit the pop up screen. With the GREEN button you can select the whole list to delete. 5.1.1.8 Search Press tu to select , then press OK and use the On Screen Dis[...]

PART 1 • English 10 5.3.1 Gomoku Press pq to select Gomoku and press OK . Play the game Gomoku on your receiver . Use the on screen help tips to set and play the game. 5.3.2 Calendar Press pq to select Calendar and press OK . Use the on screen help tips to search in your Calendar . 5.3.3 Calculator Press pq to select Calculator and press OK . Use[...]

PART 1 • English 11 English 5.4.2.3 OSD T ransparency Press tu to change settings for OSD T ransparency (1~ 8 ). 5.4.2.4 Banner Display Time Press tu to change settings for Banner Display Time ( 1sec , 3sec , 5sec , 10sec , 30sec , Always ). 5.4.2.5 Video Output Press tu to change settings for Video Output (RGB or CVBS). RGB will give you the bes[...]

PART 1 • English 12 5.4.5 Set Default Press pq to select Set Default and press OK . A pop-up screen will ask you: “ Set factory default? ”. Press OK or EXIT . Please be careful when using this function, as it will erase all the data and parameters you may have set earlier . Once you have set to Default you will have to re-install your prefere[...]

PART 1 • English 13 English W arning! NEVER disconnect the USB device from the receiver , the receiver from the main or switch the power OFF during the update/backup procedure. It can damage your receiver and warranty will void! As soon as the update has been finished, the receiver restarts automatically! NOTE: Y ou can also load a backup file [...]

PART 1 • English 14 10.0 TROUBLE SHOOTING There may be various reasons for occurring abnormal operation of the receiver . Check the receiver according to the procedures shown below . If the receiver does not work properly after checking it, please contact the dealer . Don‘t open the receiver cover . This may cause a dangerous situation and will[...]

PART 1 • English 15 English 11.0 SPECIFICA TIONS Demodulator Modulation: QPSK Input Symbol Rate: 2~45 Ms/s SCPC & MCPC signals from C & KU band satellites Video Decoder Profile level: MPEG-2 MP@ML Input Rate: Max. 60 Mbits/s Video Resolution: 720 x 576 pixels (PAL), 720 x 480 pixels (NTSC) Aspect Ratio: 4:3, 16:9 Audio Decoder ISO/IEC 11[...]

PART 1 • English 16 General Data Input V oltage Range: 100-240 V AC 50/60 Hz Power consumption: max 18 W , typ. 4.6 W Stand-by Power consumption: 0.50 W Operating T emperature: +0 ~ 40 °C Storage T emperature: -30 ~ 80 °C Operating Humidity Range: 10 ~ 85%, RH, Non-condensing Size (WxDxH): 180 x 130 x 45 mm W eight: ca. 0.457 kg[...]