TANDBERG IP GW 3500 инструкция обслуживания

Codian IP Gateway IP GW 3500 Series Getting started[...]

Codian IP Gateway IP GW 3500 Series Getting started[...]

Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited. Codian Limited reser ves the r ight to revise this documenta tion and to make cha[...]

T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the IP Gatew ay (IP GW) ........... .......... ............ ........... .......... ........... ............ ... 1 Package conte nts .... .......... .......... ............. ...[...]

General information 1 General informa tion About the IP G atewa y (IP GW ) The IP GW is a voice and video gate wa y that allows call s to be made betw een pair s of IP endpoints that canno t nor mall y connect dire ctl y to each other . A second Ether net por t allows fo r connections betw een tw o completely independent netw orks of endpoints . A [...]

2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: IP GW LED behavior LED Co lor Indicates Compact Flash Activity Flashing gr een One of:  the IP GW is booting  a configuration change has been made  the configuration is being transferred by F T P Console Link Green A PC is connected to the console port Status Green The[...]

General information 3 Ethernet P or t Status, for each Ether net por t: FDX Green The link has been negotiated as a full- duplex link Act Green Pa c kets ar e being transmitted on this por t Link Green The speed of the link from this port, which is either 10, 100, or 1000 Mbps P ow er Blue The IP GW is receiving po w er T able 1: IP GW LED behavior[...]

4 Co nnecting the IP GW Before you star t Step one: Connect power Connect the po w er connector on the rear of the unit to the pow er supply using the supplied po wer ca ble . (There is no On/Off switch.) Connecting po w er causes the Po w er LED to light blue and when the IP GW has booted (which can take up to tw o minutes), the Status LED will li[...]

Initial configuration 5 Initial configur ation Step one: Connect to the console port 1 Ensure po wer is connected to the IP GW and the Status LED is green. 2 Connect the console por t of the IP GW to the ser ial por t of your PC using the blue RJ45 to DB9 cab le supplied. 3 Use a ser ial ter minal program, suc h as SecureCR T or HyperT erminal, to [...]

6 Step three: Assign an IP address to P or t A The default setting for the IP GW is to use DHCP to obtain an IP address for P or t A. Y ou can assign a static IP address if you pr efer or if a DHCP ser ver is not a vailab le. If you want the IP addr ess of the IP GW to be ass igned by y our DHCP ser ver , omit this step .  T o assign a static IP[...]

Configuring the IP GW 7 Co nfiguring the IP GW Step one: Log in to the IP GW All administration of the IP GW is perfor med through the web interface. T o log in to the w eb interface of the IP GW: 1 Use your bro wser to naviga te to the IP address of the IP GW (to disco ver the IP address, r efer to the pre vious section). 2C l i c k Click here to [...]

8 Step three: C onfigure the default gatew ay and routes (optional) If the netw orks to whic h you connect contai n mor e than one subnet, yo u might need to c hange the default gatewa y preference on the IP GW (default se tting is P o r t A). Y ou might also need to add routes to the configuration of the IP GW to indicate which interface will be u[...]

Configuring the IP GW 9 Step five: C on figure the auto attendant menus (optional) Depending on the proposed configura tion of yo ur dial plan, and the settings fo r failed calls, caller s can be connected to an auto at tendant menu. The IP GW pro vides a highly flexib le menu-creation featur e . This enables y ou to crea te a menu (or a multi- la [...]

10 Step sev en: Add endpoints and call groups (optio nal) Y ou can pre-configure a list of endpoints on the IP GW. F or these endpoints, an operator or caller can simpl y c hoose the e ndpoint's name from an onscreen address book, rather than ha ving to type in the endpoint's address when a caller wants to be connected to that endpoint. Y[...]

Checking for updates 11 Checking for updates It is a good idea to regularl y c hec k for updates to the main IP GW software image . This section describes how to upgrade the IP GW using the w eb interface . Note that you can also upgrade the IP GW using FTP; this can be more reliab le if you are upgrading the device remotely . Upg rading your de vi[...]

12 T r oubleshooting and technical suppor t information Using the ev ent log to help solve a problem Unless you are ex periencing a prob lem, all e v ent logging sources should be set to the default, which is Errors, warnings and information . F or more infor mation about configur ing the ev ent log, refer to the online help accessible from the w e[...]

Technical specifications 13 T echnical specifications P ow er requiremen ts Over- current protection Ensure the suppl y to this unit is protected b y a branch circuit protector rated b y a maximum of 20A. Operating environment The IP GW must only be used within the follo wing envir onmental conditions: Anti-sta tic precautions When ser vicing or re[...]

61-0014-03[...]