Toshiba FC-210 инструкция обслуживания

GENERAL PRECA UTIONS REGARDING THE INST ALLA TION AND SER VICE FOR THE COPIER FC-210/310 The installation and service should be done by a qualified service technician. 1. T ransportation/Installation • When transpor ting/installing the copier , move it b y the casters while lifting the stoppers. The copier is quite heavy and weighs approximately [...]

3. Main Service Parts for Safety • The breaker , door s witch, fuse, ther mostat, ther mofuse, thermistor , etc. are par ticularly impor tant f or safety . Be sure to handle/install them properly . If these par ts are shor ted circuit and/or made their functions out, the y may b ur n down, f or instance, and may result in fatal accidents. Do not [...]

1 . ERR OR CODE AND SELF- DIA GNOSIS 2 . ADJUSTMENT 3 . PREVENTIVE MAINTENANCE (PM) 4 . TROUBLESHOO TING 5 . UPD A TING THE FIRMW ARE 7. WIRE HARNESS CONNECTION DIA GRAMS 6. PO WER SUPPL Y UNIT[...]

I Februar y 2002 © TOSHIBA TEC FC-210/310 CONTENTS CONTENTS 1. ERR OR CODE AND SELF-DIA GNOSIS ................................................................................... 1-1 1.1 Error Code List ............................................................................................................. ......... 1-1 1.2 Self-Diagnosis Mod[...]

II F ebr uar y 2002 © TOSHIBA TEC FC-210/310 CONTENTS 3. PREVENTIVE MAINTENANCE (PM) ........................................................................................ 3-1 3.1 T ypes of Pre ventiv e Maintenance ......................................................................................... 3-1 3.2 Outline of the Maintenance Order .[...]

III Februar y 2002 © TOSHIBA TEC FC-210/310 CONTENTS 5. UPD A TING THE FIRMW ARE ...................................................................................................... 5 - 1 5. 1 Installing Software for Firmware Update ................................................................................. 5 - 2 5.1.1 Outline ............[...]

Februar y 2002 © TOSHIBA TEC 1 - 1 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS P aper transpor t jam E0 1 P aper leading edge not reaching the exit sensor inside the copier E0 2 P aper trailing edge not passing the e xit sensor E0 3 P aper remaining inside the copier at pow er ON EB 7 Restar t time-out error P aper feeding jam E1 1 P aper misfeed f[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 2 F ebr uar y 2002 © TOSHIBA TEC Classification Error code Contents Original jam in the ADF E7 1 Or iginal not reaching the aligning sensor E7 2 Or iginal not reaching the exit sensor E7 3 Or iginal not passing the exit sensor P aper jam in the finisher E9F Punching jam EA 1 P aper transpor t delay ja[...]

Februar y 2002 © TOSHIBA TEC 1 - 3 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS Copy process related service call C 3 1 Used toner transport motor rotation abnor mal C 3 3 Dev eloper remov al shutter abnor mal C 3 5 T ransf er belt unit contact/release operation abnormal C 3 8 Auto-toner error (K) C 3 9 Auto-toner error (C) C3 A Auto-toner error (M)[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 4 F ebr uar y 2002 © TOSHIBA TEC Laser optical unit related service call CA 1 P olygonal motor rotation abnor mal CA 2 H-SYNC abnor mal C D 1 Laser calibration error (K) C D 2 Laser calibration error (C) C D 3 Laser calibration error (M) C D 4 Laser calibration error (Y) Finisher related service call [...]

Februar y 2002 © TOSHIBA TEC 1 - 5 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS <<Error histor y>> In the setting mode (08-253), the latest twenty groups of error data will be displa y ed. Displa y e xample EA1 01 08 26 17 57 32 64 64 236210000000 Error code YY MM DD HH MM SS MMM N N N ABCDEFHIJLOP 3 digits 12 digits (Y ear is indicated [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 6 F ebr uar y 2002 © TOSHIBA TEC 1. 2 Self-Diagnosis Mode Mode St ar ting Contents Exit Control panel check [0]+[1]+[PO WER] All control panel LEDs are lit, [CLEAR] or mode and all LCD pix els are tur ned [P O WER]OFF/ON ON/OFF repeatedly . T est mode [0]+[3]+[POWER] Input/output signals are checked. [...]

Februar y 2002 © TOSHIBA TEC 1 - 7 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS T ransition dia gram of self-diagnosis mode conditions *1 : During the activ ation of the “ Control panel chec k mode ” , cop ying is not possible. But after pressing [CLEAR] to make the copier ready , you can mak e copies. *2 : After ha ving used the self-diagnosis [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 8 F ebr uar y 2002 © TOSHIBA TEC 1. 2. 1 Input chec k (T est mode 03) The status of each item can be check ed by setting ON/OFF of each [FULL COLOR], [A UT O COLOR], [ENERGY SA VER], and then pressing each of the corresponding digital k ey in this test mode 03. Note: When icon is display ed with b lac[...]

Februar y 2002 © TOSHIBA TEC 1 - 9 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS Digital ke y Icon Item Condition A Bypass paper-width sensor 0 Refer to T ab le 1. B Bypass paper-width sensor 1 Refer to T ab le 1. C Bypass paper-width sensor 2 Ref er to T ab le 1. [5] D — E Bypass paper sensor 1: No paper F Bypass unit open/close switch 1: Unit is [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 10 F ebr uar y 2002 © TOSHIBA TEC Digital ke y Icon Item Condition A External pr inter controller power ON/OFF 0: Controller pow er ON B — C — [9] D F ront cover s witch 1: F ront cov er is opened. E OHP sensor 0: Opaque paper is installed. F — G Registration sensor 1 : P aper present H IPC boar[...]

Februar y 2002 © TOSHIBA TEC 1 - 11 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS Digital ke y Icon Item Condition A — B — C — [1] D — E — F — G — H — A De veloper car tridge Y is installed or not 0: Car tirdge is installed. B De veloper car tridge M is installed or not 0: Car tirdge is installed. C De veloper cartr idge C is installe[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 12 F ebr uar y 2002 © TOSHIBA TEC [FULL COLOR]ke y: OFF , [A UT O COLOR]ke y: ON, [ENERGY SA VER]ke y: OFF A — B — C — [5] D — E — F — G — H — A — B — C — [6] D — E — F — G F ront cov er , paper-exit unit open/close chec k 1: Co ver/unit is opened. H P olygonal motor rotati[...]

Februar y 2002 © TOSHIBA TEC 1 - 13 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS [1] —— [2] — Color registration sensor (front) "0" is display ed with reflection at (Sensor LED is turned ON by output check 03.) transfer belt. [3] — Color registration sensor (rear) "0" is display ed with reflection at (Sensor LED is turned[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 14 F ebr uar y 2002 © TOSHIBA TEC Digital ke y Icon Item Condition [1] — A uto-toner sensor Y Sensor output v alue is displa yed with 8 bits. [2] — A uto-toner sensor M Sensor output v alue is displa yed with 8 bits. [3] — A uto-toner sensor C Sensor output v alue is displa yed with 8 bits. [4] [...]

Februar y 2002 © TOSHIBA TEC 1 - 15 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS 1 5 0 All output OFF 1 1 0 1 Drum motor and transfer belt motor rotation 1 5 1 Code No . 101 function OFF 1 with nor mal printing speed ON 1 0 2 Drum motor and transfer belt motor rotation 1 5 2 Code No . 102 function OFF 1 with OHP printing speed (low) ON 1 0 3 P aper [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 16 F ebr uar y 2002 © TOSHIBA TEC Co d e Function Procedure 2 1 4 Fuser e xhaust fan motor Lo w/High speed 3 2 1 5 PC board cooling f an motor ON/OFF 3 2 1 6 Wire cleaner drive motor Y CW/CCW (continuous reciprocating) 2 2 1 7 Wire cleaner drive motor M CW/CCW (contin uous reciprocating) 2 2 1 8 Wire [...]

Februar y 2002 © TOSHIBA TEC 1 - 17 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS 2 6 3 Discharge lamp K ON/OFF 3 2 8 0 Laser (Y) ON/OFF 3 2 8 1 Laser (M) ON/OFF 3 2 8 2 Laser (C) ON/OFF 3 2 8 3 Laser (K) ON/OFF 3 3 0 0 Carriage fan motor rotation at standb y speed (high speed) ON/OFF 3 3 0 1 Carriage fan motor rotation at normal speed (low speed) ON[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 18 F ebr uar y 2002 © TOSHIBA TEC <Operation procedure> Procedure 1 Procedure 2 Procedure 3 Procedure 4 0 3 POWER OFF/ON POWER (Code) (Code) (Operation ON) START START (Operation OFF) (Exit) 0 3 POWER OFF/ON CLEAR POWER (Code) (Exit) (One-direction operation) START 0 3 POWER OFF/ON CLEAR POWER ([...]

Februar y 2002 © TOSHIBA TEC 1 - 19 FC-210/310 ERR OR CODES AND SELF-DIAGNOSIS 1. 2. 3 T est print mode (04) In the test print mode (04), you can print each test patter n by entering its corresponding code as f ollows. Note: Full color (YMCK) mode is not av ailable in 230, 231 and 234. <Operation procedure> Notes: 1. When an error has occurr[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 20 Februar y 2002 © T OSHIBA TEC 1 0 4 Reproduction ratio adjustment of 1 2 8 1~255 When the value increases by 1, the re- 1 secondary-scanning direction production ratio in the secondary-scan- (scanner section) ning direction (vertical paper feeding di- rection) increases by approx. 0.1522%. 1 0 5 Im[...]

Februar y 2002 © TOSHIBA TEC 1 - 21 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 2 2 1 Automatic filling of Color (Y, M, C) – 0~255 Fills the developer from the developer 5 developer material cartridge (about 3 min.) and then adjusts and automatic ad- the auto-toner sensor output to set in the justment of the auto- range of 3.50~4.50V (about 2 min[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 22 Februar y 2002 © T OSHIBA TEC 3 1 8 Transfer bias Normal paper Y 59 0~255 The bias value of the transfer roller is 1 3 1 9 output adjust- mode / Thin M 5 9 0~255 set. The higher the value, the larger the 1 3 20 ment paper mode C 5 9 0~255 transformer output becomes. The adjust- 1 3 2 1 (Full color)[...]

Februar y 2002 © TOSHIBA TEC 1 - 23 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 3 6 1 Transfer bias Normal paper K 4 9 0~255 The bias value of the transfer roller is 1 output adjust- mode / Thin set. The higher the value, the larger the ment (Black) paper mode transformer output becomes. This ad- 3 6 3 Thick paper 1 K 4 9 0~255 justment value becom[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 24 Februar y 2002 © T OSHIBA TEC 4 0 2 Fine adjustment of 3767 0~ When the value increases by 1, the rota- 1 fuser motor rotation speed 65535 tion speed of fuser motor decreases by 0.026%. 4 0 4 Fine adjustment of 9832 0~ When the value increases by 1, the rota- 1 feed motor rotation speed 65535 t io [...]

Februar y 2002 © TOSHIBA TEC 1 - 25 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 4 6 1 Color registration status display 0 0~255 The value of Y(0) shows the error status 1 0 of the color registration sensor. 0 / 16 or above: Normal 1~14: Data abnormal (sensor normal) 15: Color registration pattern reading error 4 7 0 Adjustment of primary-scan- K 1 [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 26 Februar y 2002 © T OSHIBA TEC 55 0 Density Full color Text/Photo 128 0~255 When the value increases, images 1 55 1 adjustment Text 1 2 8 0~255 m ade at center density become darker. 1 5 5 2 "Manual density" Printed image 128 0~255 1 5 5 3 fine adjustment Photo 1 2 8 0~255 1 5 5 4 (center [...]

Februar y 2002 © TOSHIBA TEC 1 - 27 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 6 1 2 Adjustment of Normal paper 2 5 5 0~255 When the value decreases, images 1 6 1 3 maximum toner Thick paper 1 2 4 9 0~255 become lighter. 1 61 4 amount Thick paper 2 2 3 7 0~255 Note: When the value increases, image 1 6 1 5 Thick paper 3 23 7 0~255 offset may occur.[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 28 Februar y 2002 © T OSHIBA TEC Adjustment mode (05) Accep- Co de Description/Mode Default table Contents Proce- Value dure 7 0 8 Offset adjust- Full color Text/Photo 128 0~255 When the value increases, the text be- 1 7 09 ment Text 1 2 8 0~255 co me s darker. 1 7 1 0 for background Printed image 128[...]

Februar y 2002 © TOSHIBA TEC 1 - 29 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Adjustment mode (05) Accep- Co de Description/Mode Default table Contents Proce- Value dure 784-0 Color balance T ext/ L 1 2 8 0~255 When the value increases, the target 4 784-1 adjustment Photo M 1 2 8 0~255 color, the original mode and the density 4 784-2 (M ) H 128 0[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 30 Februar y 2002 © T OSHIBA TEC 794-0 Color balance Te xt / L 1 2 8 0~255 When the value increases, the target 4 794-1 adjustment Photo M 1 2 8 0~255 color, the original mode and the density 4 794-2 ( K) H 12 8 0~255 area become darker. 4 795-0 Text L 1 2 8 0~255 4 795-1 M 12 8 0~255 Notes: 4 795-2 H[...]

Februar y 2002 © TOSHIBA TEC 1 - 31 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS <Operation procedure> Procedure 1 Procedure 2 Procedure 5 0 5 POWER (Code) (Sub-code) (Set a value) START START START SET INTERRUPT or (Stored in memory) CLEAR CANCEL or (For correction) (Test copy) (Exit) POWER OFF/ON ( ENERGY SAVER START ) 0 5 POWER (Code) (Auto[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 32 Februar y 2002 © T OSHIBA TEC Procedure 6 Procedure 10 Procedure 13 STOP (Code) (Image processing calculation) (Automatic adjustment) START START 0 5 POWER (Test copy) (Exit) POWER OFF/ON ( ENERGY SAVER START ) *Not acceptable when error occurs. 0 5 POWER (Code) (Automatic adjustment) START (Test c[...]

Februar y 2002 © TOSHIBA TEC 1 - 33 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 1. 2. 5 Setting mode (08) The follo wing items can be set or changed in this mode (08). 2 00 Date and time setting – 13 digits Y ear/month/date/day/hour/minute/second 1 Example: 99:08:07:5:11[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 34 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 2 1 7 Information of cassettes 1 5 0 ~ 15 0: 4 cassettes 1: 2 cassettes 2: 3 cassettes 1 installation 3: 4 cassettes 4: 1 cassette(Forcib ly installing OFF) 15: A utomatic 220 Selection of lan[...]

Februar y 2002 © TOSHIBA TEC 1 - 35 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 3 0 2 Resettable/original counter EUR: 3 0 ~ 3 Sets if the resettable and original counters 1 displa y UC: 0 are displa yed. JPN:0 0: Off 1: Resettab le counter 2: Original counter 3: Resettabl[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 36 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 4 0 6 Image quality control 1 0 ~ 1 After pr inting is finished and the time set in 1 auto-star t (standby time) 08-452 has passed, image quality control will star t when printing is star ted [...]

Februar y 2002 © TOSHIBA TEC 1 - 37 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 4 1 6 Image quality control 0 0 ~ 16 Accum ulated total of CE1, CE2, CE4 1 abnormal detection (Max.16 times) counter (M) * Enab led when ‘Image quality control 3 displa y/0 clearing (08-401)?[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 38 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name De f ault table Contents Proce- value dure 5 0 3 Density mode prior ity 1 0 ~ 1 0: A utomatic 1: Man ual (Center) 1 5 0 4 Color mode prior ity 2 0 ~ 2 0: A uto color 1: Black 2: Full color 1 6 0 0 Access code mode 0 0 ~ 2 0: Disabled [...]

Februar y 2002 © TOSHIBA TEC 1 - 39 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accept- Code Name Def ault table Contents Proce- value dure 6 2 2 Reading resolution initial 2 0 ~ 2 The initial value of the read resolution in the 1 v alue setting scan function is set. (scanning) 0 : 600dpi 1: 300dpi 2: 150dpi 6 2 3 P er manent file[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 40 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 6 4 5 Correction of reproduction 1 0 0 ~ 10 Sets the reproduction ratio f or X in 1 copy 1 ratio in the editing cop y mode (including magazine sor t) to "Reproduction ratio x Correction r[...]

Februar y 2002 © TOSHIBA TEC 1 - 41 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 7 1 2 Fuser roller temperature for 3 0 ~ 17 0: OFF 1: 60°C 2: 65°C 3: 70°C 1 energy sav er mode with 4: 75°C 5: 80°C 6: 85°C 7: 90°C prior ity aim of energy saving 8: 95°C 9: 100°C 10:[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 42 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 8 1 8 Registration jam counter 0 0 ~ Jam on paper tr ailing edge at the 1 displa y 9999999 registration roller (Accum ulated total of E01) 8 2 0 P aper exit jam counter displa y 0 0 ~ F requen[...]

Februar y 2002 © TOSHIBA TEC 1 - 43 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 8 4 1 Drum M life counter 0 0 ~ Counts the number of sheets printed at 1 (displa y/0 clear ing) 999999 d ru m M . ( C o d e 08-858 and 875 are reflected.) 8 4 2 Drum C life counter 0 0 ~ Counts[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 44 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 8 7 3 De veloper C time counter 0 0 ~ Rotation time (sec.) of de veloper motor 1 (display/0 clearing) 999999 8 7 4 De veloper K time counter 0 0 ~ Rotation time (sec.) of de veloper motor 1 (d[...]

Februar y 2002 © TOSHIBA TEC 1 - 45 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 8 9 2 Current v alue of general PM 0 0 ~ T otal number of printouts (copier + printer) 1 counter (displa y/0 clearing) 999999 f or li f e related (doub le count) (Code 08-858 and 875 are reflec[...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 46 Februar y 2002 © T OSHIBA TEC Setting mode (08) Accep- Code Name Def ault table Contents Proce- value dure 9 2 6 UI data 3rd language version – – VXXX.YYY Z 2 in HDD (Z: Language code, P age. 5-22) 9 2 7 UI data 4th language version – – VXXX.YYY Z 2 in HDD (Z: Language code, P age. 5-22) 9 [...]

Februar y 2002 © TOSHIBA TEC 1 - 47 FC-210/310 ERROR CODES AND SELF-DIA GNOSIS Mode state (Code) START SET INTERRUPT or (Stored in memory) CANCEL CLEAR (For correction) 0 8 POWER (Exit) POWER OFF/ON START (1st setting value) (2nd setting value) <Operation procedure> Procedure 1 Procedure 2 (Code) (Set a value) START SET INTERRUPT or (Stored [...]

FC-210/310 ERROR CODES AND SELF-DIA GNOSIS 1 - 48 Februar y 2002 © T OSHIBA TEC <<Procedure to cop y the counter value (08-257)>> 1. T ur n ON the pow er while [0] and [8] are pressed simultaneously . 2. Enter the code [257] with the digital ke ys and press the [ST ART] k ey (the f ollowing is displa yed). Note: Bef ore performing the [...]

Februar y 2002 © TOSHIBA TEC 2 - 1 FC-210/310 ADJUSTMENT 2.5 Image dimensional adjustment Order Items Code in mode 05 1 2.5.1 P aper alignment (paper buckle) at the registr ation roller 439-452,492 2 2.5.2 Registration motor speed adjustment 4 0 6 3 (a ) Reproduction ratio of primar y-scanning direction 40 0 4 (b ) Pr imary-scanning data laser wr [...]

FC-210/310 ADJUSTMENT 2 - 2 F ebr uar y 2002 © TOSHIBA TEC 2.2 Adjustment of the A uto-T oner Sensor 2.2.1 A utomatic removing of de veloper material Notes: 1. This procedure is not necesar y if dev eloper mater ial is not filled at the time of unpac king. 2. After the de veloper material has been remov ed, perform the maintenance of the processin[...]

Februar y 2002 © TOSHIBA TEC 2 - 3 FC-210/310 ADJUSTMENT ( 6 ) After all dev eloper mater ials are remov ed and "READ Y" is display ed, turn the power OFF . Time required f or removing Color dev eloper materials only : Approx. 6 min. De veloper material K only : Appro x. 3 min. ( 7 ) Open the front cov er and take out the processing unit[...]

FC-210/310 ADJUSTMENT 2 - 4 F ebr uar y 2002 © TOSHIBA TEC ( 5 ) Approx. 2 minutes after the dev eloper material filling is finished, the fo llowing displa y appears:  Y :6.30V M:6.38V C:6.38V K:6.38V   58%  Y :4.00V M:4.00V C:4.00V K:4.00V Upper line  : Current sensor voltages (V) Middle line  : Humidity (%) Lower line [...]

Februar y 2002 © TOSHIBA TEC 2 - 5 FC-210/310 ADJUSTMENT  : Current sensor voltage (V) Humidity (%) Y M C K ~29.9 3.55~3.65 3.55~3.65 3.45~3.55 3.45~3.55 30.0~44.9 3.79~3.89 3.79~3.89 3.69~3.79 3.69~3.79 45.0~59.9 3.95~4.05 3.95~4.05 3.95~4.05 3.95~4.05 60.0~74.9 4.22~4.32 4.22~4.32 4.22~4.32 4.22~4.32 75.0~ 4.45~4.55 4.45~4.55 4.45~4.55 4.45~4[...]

FC-210/310 ADJUSTMENT 2 - 6 F ebr uar y 2002 © TOSHIBA TEC <T roubleshooting in auto-toner sensor adjustment> (measures against adjustment error) Check which color is in adjustment error . Is the dev eloper unit filled with dev eloper mater ial? (Is the de v eloper car tr idge empty?) (1) Check if the shutter seal is remo ved from the de v e[...]

Februar y 2002 © TOSHIBA TEC 2 - 7 FC-210/310 ADJUSTMENT 2.3 Adjustment of Image Quality Contr ol ( 1 ) At the time of unpac king Prior to image dimensional adjustment, perform the “A utomatic initialization of image quality control (05-879)” procedure. ( 2 ) When any of the f ollowing par ts is replaced, be sure to perf or m the “Automatic [...]

FC-210/310 ADJUSTMENT 2 - 8 F ebr uar y 2002 © TOSHIBA TEC 2.4 Adjustment of Color Registration Contr ol After ha ving finished the "Automatic initialization of image quality control (05-879)” procedure, perf or m the "F orced perf or ming of color registration control adjustment (05-407)" procedure. C o de Adjustment item Content[...]

Februar y 2002 © TOSHIBA TEC 2 - 9 FC-210/310 ADJUSTMENT 2.5 Image Dimensional Adjustment There are se ver al adjustment items in the image dimensional adjustment, as listed below . Prior to this image dimensional adjustment, perf or m the "A utomatic initialization of image quality control (05-879)". When adjusting these items, the f ol[...]

FC-210/310 ADJUSTMENT 2 - 10 Februar y 2002 © T OSHIBA TEC In accordance with the procedure described below , mak e adjustment of each adjustment item so that the measured values obtained from test copies satisfy the specification. By pressing the [ENERGY SA VER] k ey , immediately after star ting the adjustment mode (05), single-sided test cop yi[...]

Februar y 2002 © TOSHIBA TEC 2 - 11 FC-210/310 ADJUSTMENT 2.5.1 P aper alignment (paper buc kle) at the registration roller If the paper f eed roller has prematurely become defectiv e, it is possib le to e xtend its ser vice life , if necessar y , b y increasing the aligning amount, as a temporar y measure until a replacement becomes av ailable . [...]

FC-210/310 ADJUSTMENT 2 - 12 Februar y 2002 © T OSHIBA TEC 2.5.2 Registration motor speed adjustment The paper transport speed of the registration roller vis-a-vis the image pir nt speed can be set to the optimum v alue. <Procedure> ( 1 ) While pressing the digital ke ys [0] and [5] simultaneously , turn the power ON.  (Adjustment mode) ([...]

Februar y 2002 © TOSHIBA TEC 2 - 13 FC-210/310 ADJUSTMENT 2.5.3 Printer section related adjustment ( a ) Reproduction ratio adjustment of primar y-scanning direction (Fine adjustment of polygonal motor rota- tion speed) 1. While pressing the digital ke ys [0] and [5] simultaneously , turn ON the power .  (Adjustment mode) 2. Press [1]  [PRIN[...]

FC-210/310 ADJUSTMENT 2 - 14 Februar y 2002 © T OSHIBA TEC (c) Reproduction ratio adjustment of secondar y-scanning direction (Fine adjustment of drum motor/transf er belt motor rotation speed) 1. While pressing the digital ke ys [0] and [5] simultaneously , tur n ON the power .  (Adjustment mode) 2. Press [1]  [PRINTER/NETW ORK]. (A grid pa[...]

Februar y 2002 © TOSHIBA TEC 2 - 15 FC-210/310 ADJUSTMENT A 21 1 B D C 26 6 F eeding direction [Grid pattern] <Adjustment order> [0] [5] [power ON]  [1]  [PRINTER/NETW ORK] (2nd cassette, A3/LD) A : 05-400  200±0.5 mm (0.164 mm/step)  05-407 B : 05-470  5±0.5 mm (0.042 mm/step)  05-407 C: 05-401  200±0.5 mm (0.15 mm/s[...]

FC-210/310 ADJUSTMENT 2 - 16 Februar y 2002 © T OSHIBA TEC 2.5.4 Scanner related adjustment (a) Image distor tion adjustment Note: The screws on the rear side of mirror-1 and -3 m ust not be adjusted. <Procedure> Remov e the original glass and the left top cov er , and then mov e carriage-1 toward the paper e xit side until it stops. Inser t[...]

Februar y 2002 © TOSHIBA TEC 2 - 17 FC-210/310 ADJUSTMENT Step 2 In case of  : Tighten the mirror-1 adjustment screw (CW).  Normal image In case of  : Loosen the mirror-1 adjustment screw (CCW).  Normal image Note: After the image distor tion adjustment, when the adjustment screws of mirror-1 and -2 are turned, lock the adjustment scre[...]

FC-210/310 ADJUSTMENT 2 - 18 Februar y 2002 © T OSHIBA TEC (b) Image sk ewing adjustment F eeding direction F eeding direction Image P aper If the cop y image is tilted e ven when the original is placed precisely against the original scale, adjust the original scale to correct this problem. When the image is tilted as in  : • Mov e the origin[...]

Februar y 2002 © TOSHIBA TEC 2 - 19 FC-210/310 ADJUSTMENT The f ollowing adjustments (c) to (g) should be conducted using T est Char t No . TCC-1. (Ref er to page 2- 22.) (c) Reproduction ratio adjustment of primar y-scanning (Scanner section) 1. While pressing the digital ke ys [0] and [5] simultaneously , turn the power ON.  (Adjustment mode)[...]

FC-210/310 ADJUSTMENT 2 - 20 Februar y 2002 © T OSHIBA TEC (e) Image location adjustment of primar y-scanning direction (Scanner section) 1. While pressing the digital ke ys [0] and [5] simultaneously , tur n the power ON.  (Adjustment mode) 2. Place T est Char t No . TCC-1 on the original glass (with the arrow positioned at the left rear side)[...]

Februar y 2002 © TOSHIBA TEC 2 - 21 FC-210/310 ADJUSTMENT (g) Adjustment of image trailing edge margin 1. While pressing the digital ke ys [0] and [5] simultaneously , turn the power ON.  (Adjustment mode) 2. Place T est Char t No . TCC-1 on the original glass (with the arrow positioned at the left rear side). 3. Press [ENERGY SA VER]  [ST A[...]

FC-210/310 ADJUSTMENT 2 - 22 Februar y 2002 © T OSHIBA TEC B D E A C <Adjustment order> [0][5][P ower ON]  (Char t TCC-1)  [ENERGY SA VER]  [ST AR T] (A4/L T , 100%, full color and text/photo) A: 05-482  200±0.5 mm (0.2 mm/step)  05-407 B: 05-104  150±0.5 mm (0.23 mm/step)  05-407 C: 05-106  5±0.5 mm (0.042 mm/step[...]

Februar y 2002 © TOSHIBA TEC 2 - 23 FC-210/310 ADJUSTMENT [1] [2] [2] [3] [3] [3] [4] [5] [6] [6] [8] [8] [9] [10] [11] [12] [13] [14] [7] [7] [7] [7] T OSHIBA COLOR CHART No .TCC-1 [2] [2] [1] [1] [1] [1] Grid patter ns : F or adjusting margin (void) and scanner section [2] YMCK patches : F or checking unif or mity [3 ] Resolution patter ns : For[...]

FC-210/310 ADJUSTMENT 2 - 24 Februar y 2002 © T OSHIBA TEC C o d e Adjustment item Contents 6 4 3 Automatic gamma adjustment 2.6.1 A utomatic gamma adjustment ( 1 ) At the time of unpacking: When the reproduction of gradation is not appropriate , the gradation reproducibility of all colors Y , M, C and K can be corrected by perf or ming this autom[...]

Februar y 2002 © TOSHIBA TEC 2 - 25 FC-210/310 ADJUSTMENT 2.6.2 Density adjustment The center density and the density v ar iation controlled b y density adjustment ke ys can be adjusted as f o llows. Original mode T e xt/photo T e xt Printed Photo M ap Items to be adjusted Remarks image 550 551 552 553 554 560 561 562 563 564 570 571 572 573 574 5[...]

FC-210/310 ADJUSTMENT 2 - 26 Februar y 2002 © T OSHIBA TEC Original mode T e xt/ Te x t Printed Photo M ap Item to be Remarks photo image adjusted Adjustment code 7 7 9 7 8 0 7 8 1 7 8 2 7 8 3 Y e l l o w 00000 L o w density Sub-code 11111 Medium density 22222 H i g h density Adjustment code 7 8 4 7 8 5 7 8 6 7 8 7 7 8 8 Magenta 00000 L o w densit[...]

Februar y 2002 © TOSHIBA TEC 2 - 27 FC-210/310 ADJUSTMENT 2.6.5 Judgment threshold f or A CS The judgment lev el is adjusted f or the automatic identification of whether the or iginal set on the glass is blac k-and-white or color . Namely , this is to adjust the judgment le v el used when “ A uto color ” is selected in the color mode. Code Adj[...]

FC-210/310 ADJUSTMENT 2 - 28 Februar y 2002 © T OSHIBA TEC <Procedure> (1) While pressing [0] and [5] simultaneously , tur n ON the power . ( 2 ) Enter code [682] with digital k eys. ( 3 ) Enter a setting v alue: The setting v alue should be in two digits; the first digit is the time-out period for A3/LD original size while the second digit [...]

Februar y 2002 © TOSHIBA TEC 2 - 29 FC-210/310 ADJUSTMENT C od e Color mode Original mode Contents 7 3 7 Full color 738 739 740 741 74 2 Black 743 744 745 746 T e xt/photo Te x t Printed image Photo Map T ext/photo Te x t Printed image Photo Map 2.6.7 Sharpness adjustment If you w ant to make cop y images look softer or shar per , perform the f ol[...]

FC-210/310 ADJUSTMENT 2 - 30 Februar y 2002 © T OSHIBA TEC 2.7 High-V oltage T ransformer Settings 2.7.1 Overview This machine uses f our main high-voltage transf ormers for charging/de v elopment/discharging and one transf er transformer for tr ansf er/suction. The main high-v oltage transformers (PS-HVT -M-314) are used each f or one of the colo[...]

Februar y 2002 © TOSHIBA TEC 2 - 31 FC-210/310 ADJUSTMENT ( 5 ) Enter code [253] and press the [ST ART] k e y .  The upper limit value f or main charger grid bias is displa yed f or each Y , M, C and K. ( 6 ) Enter the sub-code (0: Y , 1: M, 2: C , 3: K) and press the [ST AR T] ke y . ( 7 ) Enter a value according to the supplementar y data she[...]

FC-210/310 ADJUSTMENT 2 - 32 Februar y 2002 © T OSHIBA TEC ( 2 ) Loosen the 2 screws f or fixing the doctor blade (M3), and inser t the gauge “0.65” of the jig into the gap between the de veloper slee ve and the doctor blade to adjust the gap . F asten the screws f or fixing the doctor b lade after adjusting. T oner-scattering pre vention seal[...]

Februar y 2002 © TOSHIBA TEC 2 - 33 FC-210/310 ADJUSTMENT 2.9 Adjustment of the Scanner Section 2.9.1 Carriages ( a ) Installing carriage dr iv e wires When replacing the carriage dr iv e wires with new wires , proceed as illustrated below: Notes: 1. Since the carr iage drive wires are applied with proper tension by tension springs, there is no ne[...]

FC-210/310 ADJUSTMENT 2 - 34 Februar y 2002 © T OSHIBA TEC F R ( b ) Adjusting the positions of carriage-1 and -2 1. Loosen 2 scre ws (on the front and rear) which are fixing carriage-1 to the wires, and another 1 screw (on the front) which is fixing carriage-2 to the wires. 2. Mov e carriage-2 to the exit side . Inser t the car- riage jigs into t[...]

Februar y 2002 © TOSHIBA TEC 2 - 35 FC-210/310 ADJUSTMENT (c) Installing the carriage dr ive wires to the wire pulle ys Ball terminal Winding the wire to the wire pulle ys: 1. Fit the 3-mm ball ter minal in the center of the wire into the hole of the wire pulley . The wire should be positioned so that the hook at its end f aces upward with its cri[...]

FC-210/310 ADJUSTMENT 2 - 36 Februar y 2002 © T OSHIBA TEC Notes : 1. When winding the wires on the pulleys, take the f ollowing precautions: · Do not wind the wire on the pulley with the wire twisted. · Wind the wire strongly so that all the tur ns of the wire are in firm contact with the surface of the pulle y . · Each time you wind a turn on[...]

Februar y 2002 © TOSHIBA TEC 2 - 37 FC-210/310 ADJUSTMENT 2.9.2 Lens unit (a) Replacing the lens unit · Since the lens unit was precisely adjusted at the f actor y , it must not be readjusted in the field or some of its components must not be replaced. If necessary , the lens unit should be replaced as a unit. · While replacing with a ne w lens [...]

FC-210/310 ADJUSTMENT 2 - 38 Februar y 2002 © T OSHIBA TEC ( b ) Installing the lens unit Use the positioning pins to install the lens unit. By that the installing position of the lens unit is fix ed, and theref ore there is no need to adjust the magnification ratio of the lens . <Procedure> 1. Inser t the positioning pins (front and rear)in[...]

Februar y 2002 © TOSHIBA TEC 2 - 39 FC-210/310 ADJUSTMENT 2.10 Adjustment of the P aper Feeding System 2.10.1 Cassette sidewise deviation (1) Loosen 5 screws f or fixing the cassette front cov er , and the side wise deviation can be adjusted to ward the front or the rear by a maxim um of 3 mm. (2) If the image is shifted tow ard the rear of paper [...]

FC-210/310 ADJUSTMENT 2 - 40 Februar y 2002 © T OSHIBA TEC 2.11 Ke y Cop y Counter (MU-8, MU-10) T o make a k e y copy counter a vailab le, the f ollowing 2 components must be installed to the copier . Counter sock et MU-10 K ey cop y counter MU-8 <Installation procedure> ( 1 ) Remov e the rear cov er . (2 ) Remove the f eed side upper cov e[...]

Februar y 2002 © TOSHIBA TEC 2 - 41 FC-210/310 ADJUSTMENT ( 4 ) Connect the connector of the counter sock et to the har ness connector of the copier side. ( 5 ) Install the counter soc k et to the machine frame with two M3 scre ws. ( 6) Reinstall the feed side upper co ver and the rear cov er . ( 8 ) Enter the value “3” in the setting mode (08[...]

Februar y 2002 © TOSHIBA TEC 3 - 1 FC-210/310 PREVENTIVE MAINTENANCE 3. PREVENTIVE MAINTENANCE (PM) 3. 1 T ypes of Preventive Maintenance The follo wing two types of pre ventiv e maintenance should be perf or med: Note: V alues of the sheets correspond to the FC-210/FC-310. ( 1 ) General maintenance (General PM) General maintenance should be perfo[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 2 Februar y 2002 © TOSHIBA TEC 3. 2 Outline of the Maintenance Order (1 ) Preparation a. Discuss current machine conditions with the key operator and note them down. b . Before star ting maintenance , make a f ew sample copies b y TCC-1 char t and keep them f or later reference purposes. c . T ur n OFF the powe[...]

Februar y 2002 © TOSHIBA TEC 3 - 3 FC-210/310 PREVENTIVE MAINTENANCE General Maintenance Checklist 1. Developer material 40/60 * 8 2. Doctor blade (40/60) * 1 Developer K 3. Developer unit drum seal (40/60) * 9 counter 4. F ront/rear sides of de veloper unit (40/60) * 2 ( 08 - 847) 5. Oil seal portion A V 6. Drum cleaning blade 40/60 * 3 <P23-I[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 4 Februar y 2002 © TOSHIBA TEC 31. Cleaning roller 40/60 ch.3.6.7 <P28-I45> 32. Upper thermistors A (40/60) Fuser unit Fuser unit 33. Lower thermistors A (40/60) counter 34. Fuser inlet guide A (40/60) (08-854) 35. Fuser exit guide A (40/60) 36. Paper exit roller A Image quality 37. Image quality sensor?[...]

Februar y 2002 © TOSHIBA TEC 3 - 5 FC-210/310 PREVENTIVE MAINTENANCE Color Maintenance Checklist 1. De veloper material (Y ,M,C) 40/60 * 8 D e v e l o p e r Y , 2. Doctor blade (40/60) * 1 M,C counter 3. Developer unit drum seal (40/60) * 9 (08-844,845, 4. F ront/rear sides of de veloper unit (40/60) * 2 846) 5. Oil seal portion A V 6. Drum cleani[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 6 Februar y 2002 © TOSHIBA TEC [Front sectional view] 55 62 48 21 31 30 25 28 35 29 24 34 67 68 22 66 65 64 63 33 54 53 56 58 59 51 60 60 57 39 61 38 46 44 43 45 47 41 40 41 42 40 41 42 42 40 48 46, 50 69 27 23 32 36 26 37[...]

Februar y 2002 © TOSHIBA TEC 3 - 7 FC-210/310 PREVENTIVE MAINTENANCE [Processing unit (EPU)] 5 5 5 5 16 3, 18 3 3 3, 18 10, 15 11 2 17 14 7 19 16 17 16 17 16 17 14 7 19 14 7 19 14 7 8, 6 8, 6 8, 6 8, 6 19 1 2 1 2 1 2 1 10, 15 11 10, 15 11 10, 15 12,13 11 12,13 12,13 12,13 Developer unit K Developer unit C Developer unit M Dev eloper unit Y[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 8 Februar y 2002 © TOSHIBA TEC [F ront side drive system] 49 20[...]

Februar y 2002 © TOSHIBA TEC 3 - 9 FC-210/310 PREVENTIVE MAINTENANCE * Notes on the Preventive Maintenance Checklist * 1. Doctor blade cleaning Note: This cleaning should be done subsequent to “ Automatic remo ving of dev eloper material ”. ( 3 ) Remove the de v eloper unit cov er . Inser t the doctor blade cleaning jig between the doctor blad[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 10 F ebr uar y 2002 © T OSHIBA TEC * 3 Cleaning blade If poor cleaning has occurred due to such causes as adhesion of paper dust, etc. prior to the specified number of printouts for replacement, replace the cleaning blade as required because the blade edge may have been damaged. * 4 Recovery blade If the blade [...]

Februar y 2002 © TOSHIBA TEC 3 - 11 FC-210/310 PREVENTIVE MAINTENANCE 3. 4 PM Kit Kit name Breakdown of kits Part name Q'ty No. of printouts for replacement cycle 1. Dev eloper mater ial Y PS-ZDFC31Y 1 DEV -KIT -FC31 1. Developer material M PS-ZDFC31M 1 (40/60K kit) 1. Developer material C PS-ZDFC31C 1 40/60K 1. Developer material K PS-ZDFC31[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 12 F ebr uar y 2002 © T OSHIBA TEC 3. 5 List of Adjustment T ools Name Parts List Page Item Door switch keep-ON jig 1 0 0 1 Wire holder jig 1 0 0 2 Doctor - sleeve gap adjustment jig 10 0 3 Cleaning brush 1 0 0 6 Doctor blade cleaning jig 10 0 7 T est char t (No. TCC-1) 1 0 0 9 Scanner carriage jig (front) 10 0[...]

Februar y 2002 © TOSHIBA TEC 3 - 13 FC-210/310 PREVENTIVE MAINTENANCE 3.6 Precautions for Storing/Handling Supplies and Parts 3.6.1 Precautions for storing T OSHIBA supplies A. T oner and dev eloper T oner and dev eloper should be stored in a shaded place where the ambient temperature is betw een 10 to 35 ° C (no condensation), and should also be[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 14 F ebr uar y 2002 © T OSHIBA TEC Notes: 1. Application of the patting powder is for reducing the friction between the drum and the cleaning blade. If the application of patting powder is neglected, the drum and the cleaning blade may be damaged. 2. When some fibers adhere to the cleaning blade edge, they may [...]

Februar y 2002 © TOSHIBA TEC 3 - 15 FC-210/310 PREVENTIVE MAINTENANCE 3.6.3 Checking and cleaning of the drum cleaning blade and transfer belt cleaning blade (1) Handling precautions Since the edge of the cleaning blade performs the cleaning operation, pay special attention when handling it: • Do not allow any hard object to hit or rub against t[...]

FC-210/310 PREVENTIVE MAINTENANCE 3- 16 F ebr uar y 2002 © T OSHIBA TEC Lower heat roller • Do not lea ve an y oil (finger prints, etc.) on the low er heat roller . • Be careful not to allow any hard object to hit or rub against the low er heat roller , or it may be damaged, possibly resulting in poor cleaning. (2) Checking • Check f or stai[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 1 FC-210/310 TROUBLESHOO TING 4. TROUBLESHOO TING <CA UTION IN REPLA CING PC BO ARDS> The ID for each mac hine is registered on the LGC board, the IMC board, the IMG board and the SYS board. So, if their replacement is required, be sure to replace only one boar d at a time . If more than one of the LGC boar[...]

FC-210/310 TR OUBLESHOO TING 4 - 2 F ebr uary 2002 © TOSHIBA TEC YES YES NO YES NO Where w as the paper stopped? Near the e xit sensor (paper not damaged) Are the registr ation sensor and paper e xit sensor functioning proper ly? (Does the actuator retur n nor mally?) 1. In the test mode (03) chec k if each sensor is functioning. 2. Reconnect each[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 3 FC-210/310 TROUBLESHOO TING [ E0 3] Paper remaining inside the copier at po wer ON Is an y paper remaining inside the copier? Remov e the paper . Ref er to [E01], [E02] and [E11] to [E26]. [E B7 ] Restar t time-out err or T ur n the power OFF and bac k ON. In case that this error occurs frequently , confir m th[...]

FC-210/310 TR OUBLESHOO TING 4 - 4 F ebr uary 2002 © TOSHIBA TEC 4.1.2 Paper feeding jam [ E1 1] P aper misfeed fr om the ADU Is an y paper remaining in the paper f eed area inside the ADU? Remove the paper . Is the connector J104 on the LGC board disconnected? Is the har ness betw een the LGC board and the ADU dr aw er connector open-circuited? R[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 5 FC-210/310 TROUBLESHOO TING [E 13 ] P aper misfeed from the 1st cassette [ E1 4] P aper misfeed fr om the 2nd cassette [ E1 5] P aper misfeed fr om the 3rd cassette [E 1 6] P aper misfeed fr om the 4th cassette Open the side door ; does an y paper remain in the paper path from the cassette? Remov e the paper . [...]

FC-210/310 TR OUBLESHOO TING 4 - 6 F ebr uary 2002 © TOSHIBA TEC 4.1.3 Paper transport jam (Paper not reac hing the registration sensor after feeding) [ E2 1] Paper transport jam from the LCF [E 22 ] P aper transpor t jam from the 1st cassette [ E2 3] P aper transpor t jam fr om the 2nd cassette [ E2 4] P aper transpor t jam fr om the 3rd cassette[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 7 FC-210/310 TROUBLESHOO TING 4.1.4 Cover open jam [ E4 1] Front cover opened during printing * T o av oid electrical hazards, the follo wing checks must be made after unplugging the po wer cord. Is the front co v er or the paper-e xit unit open? Close the front cov er or the paper-e xit unit. Is the A C har ness[...]

FC-210/310 TR OUBLESHOO TING 4 - 8 F ebr uary 2002 © TOSHIBA TEC [ E4 3] ADU pulled out during printing Is the ADU pushed in securely to the copier? Push in the ADU securely to the copier . Is connector J104 on the LGC board disconnected? Is the har ness betw een the LGC board and the ADU dr aw er connector open-circuited? Reconnect the connector [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 9 FC-210/310 TROUBLESHOO TING 4.1.5 P aper jam in ADU and reversing area [ E5 0] P aper not reaching the ADU [E 5 1] Paper not restarting fr om the ADU stack [E 54 ] ADU paper transpor t jam Is the ADU pushed in securely to the copier? Push in the ADU securely to the copier . Is the connector J104 on the LGC boar[...]

FC-210/310 TR OUBLESHOO TING 4 - 10 Februar y 2002 © T OSHIBA TEC 4.1.6 Original jam in the RADF [ E7 1] Original not reaching the aligning sensor [ E7 2] Original not reaching the exit sensor [ E7 3] Original not passing the exit sensor [T w o or more originals are fed simultaneousl y .] Ha v e too man y or iginals been placed? Reset the original[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 11 FC-210/310 TROUBLESHOO TING [The original does not reach the aligning r oller .] Is the pic k-up roller or f eed roller stained? Clean the roller . Is the gap betw een the aligning plate and the f eed roller too small? Adjust the gap . Is the tr anspor ting f orce of the pic k-up roller or the f eed roller ins[...]

FC-210/310 TR OUBLESHOO TING 4 - 12 Februar y 2002 © T OSHIBA TEC 4.1.7 Paper jam in the finisher [E9F] Punching jam Is there an y paper remaining on the tr anspor t path in the finisher or copier? Remov e the paper . Is either of the connectors J1 or J3 on the punch dr iv er PC board disconnected? Is the har ness connecting the punch dr iv er PC [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 13 FC-210/310 TROUBLESHOO TING YES [ EA 2] Finisher paper transpor t stop jam Is there an y paper remaining on the tr anspor t path in the finisher or copier? Remove the paper . Is an y of the connectors J17, J24, J9 and J11 on the finisher controller PC board disconnected? Is an y of the har nesses connecting be[...]

FC-210/310 TR OUBLESHOO TING 4 - 14 Februar y 2002 © T OSHIBA TEC [ EA 4] Finisher front door opened during printing Is there an y paper remaining on the tr anspor t path in the finisher or copier? YES Remov e the paper . NO Is the finisher connected with the copier? NO Connect the finisher with the copier . YES Is the connector J12 on the finishe[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 15 FC-210/310 TROUBLESHOO TING Is the connector J5 on the punch dr iv er PC board disconnected? Is the har ness connecting betw een the punch dr iv er PC board and front door s witch (MS2P) open- circuited? YES Connect the connector securely . Replace the har ness. NO Is the front door s witch w or king proper ly[...]

FC-210/310 TR OUBLESHOO TING 4 - 16 Februar y 2002 © T OSHIBA TEC [EA8] Saddle stitcher stapling jam Is there an y paper remaining on the tr anspor t path in the finisher , saddle stitcher section or copier , or on the stapling tr a y? YES Remove the paper . NO Is the jam cleared by taking off the staple car tr idge from the saddle stitcher and re[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 17 FC-210/310 TROUBLESHOO TING [ EA 9] Saddle stitcher door opened during printing I s there an y paper remaining on the tr anspor t path in the finisher , saddle stitcher section or copier ? YES Remove the paper . NO Is the saddle stitcher door closed? NO Close the door . YES Is either of the connectors J10 or J[...]

FC-210/310 TR OUBLESHOO TING 4 - 18 Februar y 2002 © T OSHIBA TEC [ EA B] Saddle stitcher transport stop jam Is there any paper remaining on the tr anspor t path in the finisher , saddle stitcher section or copier ? YES Remov e the paper . NO Is either of the connectors J10 or J9 on the saddle stitcher controller PC board disconnected? Is an y of [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 19 FC-210/310 TROUBLESHOO TING [EAE] Finisher receiving time time-out jam Is the finisher w or king? Replace the finisher controller PC board. 1. Check if the v oltage (24V) is being supplied to the finisher . 2. Check the connection of the LGC board and IPC board. 3. Chec k if the har ness connecting the IPC boa[...]

FC-210/310 TR OUBLESHOO TING 4 - 20 Februar y 2002 © T OSHIBA TEC 4.1.8 Special sheet jam [ EC 2] OHP film used except fr om b ypass tray and 2nd cassette Use the 2nd cassette or the bypass tra y as the feeding source of OHP film. [ E C 3 ] OHP film used in non-OHP mode Set the specified type of paper as selected on the control panel in the paper [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 21 FC-210/310 TROUBLESHOO TING 4.1.9 Drive system related ser vice call [C05] ADU motor rotation abnormal Is the ADU motor rotating proper ly? 1. Chec k if the har ness between the LGC board and the ADU dra wer connector is open-circuited. 2. Chec k if the har ness between the s witching power supply and the ADU [...]

FC-210/310 TR OUBLESHOO TING 4 - 22 Februar y 2002 © T OSHIBA TEC [C0A] D e veloper motor rotation abnormal Is the de v eloper motor rotating proper ly? 1. Check if the connector J41 or J43 of the de veloper motor is disconnected. 2. Check if the connector J109 on the LGC board is disconnected. 3. Check if the connector J703 of the s witching powe[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 23 FC-210/310 TROUBLESHOO TING 4.1.10 Paper f eeding system related service call [C11] ADU paper side guide operation abnormal Is the ADU pushed in securely to the copier? Push in the ADU securely to the copier . Has the timing belt f or dr iving the paper side guide come off? Put the belt on properly . Is the co[...]

FC-210/310 TR OUBLESHOO TING 4 - 24 Februar y 2002 © T OSHIBA TEC [C18] LCF tra y operation abnormal Is the har ness betw een the LGC board and the LCF unit open-circuited? Is the rela y connector of the har ness betw een the LGC board and the LCF unit or the connector J105 on the LGC board disconnected? Reconnect the connector . Replace the har n[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 25 FC-210/310 TROUBLESHOO TING 4.1.11 Scanner related service call [C27] Carriage home position sensor not turning OFF within a fixed time [C28] Carriage home position sensor not turning ON within a fixed time Remov e the or iginal glass, mo v e the carr iages to the paper f eed side, tur n ON the pow er s witch,[...]

FC-210/310 TR OUBLESHOO TING 4 - 26 Februar y 2002 © T OSHIBA TEC 4.1.12 Copy process related service call [C31] Used toner transpor t motor r otation abnormal Is the har ness betw een the LGC board and the used toner tr anspor t motor open-circuited? Is the connector J123 or J102 on the LGC board, the rela y connector or the used toner tr anspor [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 27 FC-210/310 TROUBLESHOO TING [C35] T r a n s fe r b e l t u n i t contact/release function abnormal Reduce the mechanical load b y adjusting the dr iv e system. Remo v e an y f oreign matter . Is the har ness betw een the LGC board and the tr ansf er/tr anspor t unit dr a w er connector , or the har ness inside[...]

FC-210/310 TR OUBLESHOO TING 4 - 28 Februar y 2002 © T OSHIBA TEC [C3C] Main char g er wire c leaning abnormal (K) [C3D] Main char g er wire c leaning abnormal (C) [ C3 E ] Main char ger wire cleaning abnormal (M) [ C 3F ] Main charger wire cleaning abnormal (Y) Is the har ness betw een the LGC board and the EPU dr a w er connector or an y har nes[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 29 FC-210/310 TROUBLESHOO TING 4.1.13 Fuser unit related ser vice call [C41] Thermistor or heater abnormal when warming-up is started [C42] Thermistor abnormal after the copier has become read y [C43] Thermistor abnormal during warming-up after abnormality judgment [C44] Heater abnormal during warming-up after ab[...]

FC-210/310 TR OUBLESHOO TING 4 - 30 Februar y 2002 © T OSHIBA TEC [C7] E r ro r C 7 * T o av oid any hazards , be sure to unplug the power cord bef ore proceeding to check the items in 1. and 2. below . * Be sure that the fuser unit is set in place securely . 1. Check if any thermistor connector is disconnected. 2. Check if any harness of the ther[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 31 FC-210/310 TROUBLESHOO TING 4.1.14 Communications related service call [C57] Communication err or between LGC-CPU and IPC board ( 1 ) Check if any conductor patter n on the LGC board, mainly around IC23, IC72, IC74 and J125, is shor t- or open-circuited. ( 2 ) Chec k if the conductor patter n on the IPC board [...]

FC-210/310 TR OUBLESHOO TING 4 - 32 Februar y 2002 © T OSHIBA TEC 4.1.15 ADF related service call [C72] A l i g n i n g sensor automatic adjustment err or 1. Check if an y foreign matter is present between the aligning sensor and the reflecting mirror , and if the reflecting mirror is stained. 2. Check if the harness between the aligning sensor an[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 33 FC-210/310 TROUBLESHOO TING 4.1.16 Other ser vice call (1) [C94] LGC-CPU abnormal Is "Call f or ser vice" displa y ed again e v en after the copier is tur ned OFF and then bac k ON? Obser v e the condition for a while . 1. Check if the conductor patter n between LGC-CPU (IC32) and FR OM (IC24) is ope[...]

FC-210/310 TR OUBLESHOO TING 4 - 34 Februar y 2002 © T OSHIBA TEC 4.1.17 Laser optical unit related ser vice call [CA1] Po l ygonal motor rotation abnormal Is the polygonal motor rotating? 1. Check if the polygonal motor connector is disconnected. 2. Check if connector J181 or J188 on the IMC board is disconnected. 3. Check if an y har ness is ope[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 35 FC-210/310 TROUBLESHOO TING [CA2] H-SYNC abnormal Is the polygonal motor rotating? Ref er to "[CA1] P olygonal motor rotation abnor mal". Are both 10th and 12th pins of the connector J188 on the IMC board alw a ys at the le v el "L"? Ref er to "[CA1] P olygonal motor rotation abnor mal[...]

FC-210/310 TR OUBLESHOO TING 4 - 36 Februar y 2002 © T OSHIBA TEC 4.1.18 Finisher related ser vice call [CB1] Feed motor abnormal [Procedure 1] Is the second f eed motor (M8) rotating in re v erse at the specified timing? NO Replace the second feed motor or the finisher controller PC board. YES Is the shutter securely attached to the shutter upper[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 37 FC-210/310 TROUBLESHOO TING [Procedure 2] Is the second f eed motor (M8) rotating in re v erse at the specified timing? NO Replace the second f eed motor or the finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lo w er bars? NO Attach it securely . YES T ur n the f eed rol[...]

FC-210/310 TR OUBLESHOO TING 4 - 38 Februar y 2002 © T OSHIBA TEC [CB2] Delivery motor abnormal Rotate the deliv er y motor b y hand. Does it rotate smoothly? NO Correct the mechanism. YES Is the deliv er y motor cloc k sensor (PI10) w or king nor mally? NO Replace the sensor . YES Does the v oltage betw een J11-4 and -5 on the finisher controller[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 39 FC-210/310 TROUBLESHOO TING [Procedure 2] Does the tr a y reach the tr a y upper limit detecting s witch (MS5)? YES Low er the position of the tra y . NO Is the tr a y upper limit detecting s witch (MS5) w or king nor mally? NO Replace the s witch. YES Is the wir ing betw een the finisher controller PC board a[...]

FC-210/310 TR OUBLESHOO TING 4 - 40 Februar y 2002 © T OSHIBA TEC [CB4] Alignment motor abnormal Is the alignment guide home position sensor (PI6) w or king nor mally? NO Replace the sensor . YES Is the wir ing betw een the finisher controller PC board and the alignment motor (M3) correct? NO Correct the wiring. YES Is there an y mechanical prob l[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 41 FC-210/310 TROUBLESHOO TING [CB6] S t a p l e r s h ift motor abnormal Is the stapler shift home position sensor (PI7) w or king nor mally? NO Replace the sensor . YES Is the wir ing betw een the finisher controller PC board and the stapler shift motor (M4) correct? NO Correct the wiring. YES Is there an y mec[...]

FC-210/310 TR OUBLESHOO TING 4 - 42 Februar y 2002 © T OSHIBA TEC [Procedure 2] Is the connector J6 on the finisher controller PC board, J114 of the height sensor (PS1) or rela y connector J212 disconnected? YES Connect the connector . NO Is the v oltage betw een J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? NO Replace the finishe[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 43 FC-210/310 TROUBLESHOO TING [CB8] B a c kup RAM data abnormal Is the prob lem solv ed b y tur ning the po w er of the copier OFF and ON? YES End NO Is the prob lem solv ed b y replacing the finisher controller PC board? NO Replace the punch driver PC board. YES End [CB9] S a d dle stitcher/paper pushing plate [...]

FC-210/310 TR OUBLESHOO TING 4 - 44 Februar y 2002 © T OSHIBA TEC [Procedure 2] Is the paper pushing plate top position sensor (PI15S) w or king nor mally? NO Replace the sensor . YES Is the paper pushing plate motor (M8S) oper ating at the specified timing? YES Replace the saddle stitcher controller PC board. NO Is there an y prob lem with the pa[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 45 FC-210/310 TROUBLESHOO TING [ C B A ] Saddle stitcher/stitcher motor (fr ont) abnormal [CBB] S a d dle stitcher/stitcher motor (rear) abnormal Are the front or rear stitcher and its stand installed proper ly? NO Install them properly . YES Is the stitcher home position s witch on the front or rear stitcher (MS[...]

FC-210/310 TR OUBLESHOO TING 4 - 46 Februar y 2002 © T OSHIBA TEC [CBD] S a d dle stitcher/guide motor abnormal Is the guide home position sensor (PI13S) w or king nor mally? NO Replace the sensor . YES Is the guide motor (M3S) oper ating at the specified timing? YES Replace the saddle stitcher controller PC board. NO Is the guide plate dr iv e me[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 47 FC-210/310 TROUBLESHOO TING [ C B F ] Saddle stitcher/paper positioning plate motor abnormal Is the paper positioning plate home position sensor (PI7S) w or king nor mally? NO Replace the sensor . YES Is the paper positioning plate oper ating at the specified timing? YES Replace the saddle stitcher controller [...]

FC-210/310 TR OUBLESHOO TING 4 - 48 Februar y 2002 © T OSHIBA TEC [Procedure 2] Is the connector of paper pushing plate home position sensor (PI14S) connected to the connector on the saddle stitcher controller PC board? NO Connect the two connectors. YES Is the wir ing betw een the sensor and the saddle stitcher correct? NO Correct the wiring. YES[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 49 FC-210/310 TROUBLESHOO TING [CD6] S a d dle stitcher/micros witch abnormal [Procedure 1] Is the s witch actuator f or the inlet door w or king proper ly? NO Correct the mechanism. YES Is the inlet co v er s witch (MS1S) w or king nor mally? NO Replace the s witch. YES Is the v oltage of J10-8 on the saddle sti[...]

FC-210/310 TR OUBLESHOO TING 4 - 50 Februar y 2002 © T OSHIBA TEC [Procedure 2] Is the s witch actuator f or the front door w or king proper ly? NO Correct the mechanism. YES Is the front co v er s witch (MS2S) w or king nor mally? NO Replace the s witch. YES Is the v oltage of J11-12 on the saddle s witcher controller PC board 5V when the front d[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 51 FC-210/310 TROUBLESHOO TING [CD9] Swing motor abnormal [Procedure 1] Rotate the s wing motor in re v erse b y hand. Does the s wing guide mo v e up and do wn? NO Correct the s wing mechanism. YES Is the s wing guide closed detection s witch-2 (MS6) w or king nor mally? NO Replace the s witch. YES Is the s wing[...]

FC-210/310 TR OUBLESHOO TING 4 - 52 Februar y 2002 © T OSHIBA TEC [Procedure 3] Is the s wing motor cloc k sensor (PI20) w or king nor mally? NO Replace the sensor . YES Does the v oltage betw een J11-6 and -7 on the finisher controller PC board become 24V when the s wing motor star ts rotating? NO Replace the finisher controller PC board. YES Is [...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 53 FC-210/310 TROUBLESHOO TING [CDB] Punch motor abnormal Is the punch home position sensor (PI3P) w or king nor mally? NO Replace the sensor . YES Is the wir ing between the punch home position sensor (PI3P) and finisher controller PC board correct? NO Correct the wiring. YES Is the punching mechanism nor mal? N[...]

FC-210/310 TR OUBLESHOO TING 4 - 54 Februar y 2002 © T OSHIBA TEC 4.1.19 Image quality related ser vice call ( 1) After checking [CE1], [CE2] and [CE4], and taking appropriate action, perform the forced perf or ming of image quality control. 1. While pressing [0] and [5] simultaneously , turn ON the power . 2. Enter [878] with digital ke ys, and t[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 55 FC-210/310 TROUBLESHOO TING [ CE 2] Image quality sensor abnormal (no pattern le vel abnormal) 1. Check that the transf er belt unit is fully raised. 2. Check that the tr ansfer/transport unit is securely inser ted. 3. Check f or any abnormal stain, large flaw or break on the transf er belt surface . 4. Check [...]

FC-210/310 TR OUBLESHOO TING 4 - 56 Februar y 2002 © T OSHIBA TEC [ CE 4] Image quality control test pattern abnormal ( 1) Use "Image quality control abnor mal detection counter Y~K displa y/0 clear ing (08-415~418)" to check the abnormal occurring condition for each color . ( 2) Check "Output v alue display of image quality sensor/[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 57 FC-210/310 TROUBLESHOO TING [ CE 5 ] T emperature/humidity sensor upper-limit abnormal Is the har ness betw een the LGC board and the temperature/humidity sensor disconnected ? Is the connector J108 on the LGC board or the connector of the temper ature/humidity sensor disconnected ? Reconnect the connector . R[...]

FC-210/310 TR OUBLESHOO TING 4 - 58 Februar y 2002 © T OSHIBA TEC [ CF 1] Color registration control abnormal <Check of the status of color registr ation sensor error> 1. While pressing [0] and [5] simultaneously , tur n the pow er ON. 2. Enter [461] with digital ke ys and press the [ST AR T] key . 3. The color registration control result is[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 59 FC-210/310 TROUBLESHOO TING V oltage before f orced perf or ming of color registration control DC 0.7V No rm al DC 0V Check if the harness between the LGC board and the color registration sensor or the har ness between the LGC board and the IMC board is open- or shor t-circuited. Check if an y of the connector[...]

FC-210/310 TR OUBLESHOO TING 4 - 60 Februar y 2002 © T OSHIBA TEC <Check b y the grid patter n> 13 . While pressing [0] and [5] simultaneously , turn the power ON. 14 . Enter "1" with digital k ey and press the [PRINTER/NETW ORK] ke y . 15 . Check the output g r id patterns of yellow , magenta, cyan and blac k if there is image den[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 61 FC-210/310 TROUBLESHOO TING <Check b y the gradation pattern> 16 . While pressing [0] and [5] simultaneously , turn the power ON. 17 . Enter "4" with digital k ey and press the [PRINTER/NETW ORK] ke y . 18 . Check the output g radation images f or gamma adjustment if there is any abnor mality i[...]

FC-210/310 TR OUBLESHOO TING 4 - 62 Februar y 2002 © T OSHIBA TEC 4.1.20 Other ser vice call (2) [ F0 7] Communications err or between system-CPU and LGC-CPU 1. Check if the SYC board is securely connected to the MTH1 board. 2. Check if the IMC board is securely connected to the MTH1 board. 3. Check if the IMC board connector J182 is disconnected.[...]

F ebr uar y 2002 © TOSHIBA TEC 4 - 63 FC-210/310 TROUBLESHOO TING [F09] [F11] [F12] Comm unications error between system-CPU and scanner-CPU 1. Check if the IMG board connector J161 is disconnected. 2. Check if the SCM board connector J1 is disconnected. 3. Check if the harness between the IMG and SCM boards is open-circuited. 4. Check if the IMG [...]

FC-210/310 TROUBLESHOOTING 4 - 64 F ebr uar y 2002 © TOSHIBA TEC Original mode Location Phenomena All modes Color blurred in outline of Color white text or illustration de vi at io n on a colored background T e xt mode Outline in black text on a White void T e xt/Photo mode colored background Photo mode Color blurred in outline of Color Map mode l[...]

FC-210/310 TROUBLESHOOTING 4 - 66 F ebr uary 2002 © TOSHIBA TEC (2) Uneven pitch and jitter image <Symptoms> F eeding direction Original mode Location Phenomenon All modes Occurs cyclically at right Unev en pitch angles to paper feeding direction Section Step Cause Check item Main-Classification Sub-Classification Specific-Classification 1 O[...]

FC-210/310 TROUBLESHOOTING 4 - 68 F ebr uary 2002 © TOSHIBA TEC * Fine adjustment of registration roller paper tr anspor t speed The optimized value against jitter and color misalignment is not always obtained because fine error is generated in automatic adjustment. If une ven color is generated in the secondary-scanning direction of the image and[...]

February 2002 © T OSHIBA TEC 4 - 69 FC-210/310 TROUBLESHOOTING Check color reproduction. Check image density . Check gr ay balance . (3) P oor image density , color reproduction and gra y balance Cause/Section Step Check items Measures Remarks Density/Color reprodu- 1 Check the image density/color P erform the automatic gamma ction/Gray balance re[...]

FC-210/310 TROUBLESHOOTING 4 - 70 F ebr uary 2002 © TOSHIBA TEC (4) Bac kground fogging * If the main charger and developer bias outputs seem to be abnormal, exchange th e ma in h i gh-voltage transformer of the color likely to be abnormal for another transformer of another color likely to be normal, and then, output the chart again. If the same c[...]

February 2002 © T OSHIBA TEC 4 - 71 FC-210/310 TROUBLESHOOTING Moire Lack of sharpness A B (5) Moire/lack of sharpness Cause/Section Step Check items Measures Remarks Density reproduction 1 Check the gradation P erform the automatic gamma reproduction. adjustment. Parameter adjustment 2 Check the image proces- Check the sharpness adjustment value [...]

FC-210/310 TROUBLESHOOTING 4 - 72 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Remarks Density 1 Is the density too high? P erform the automatic gamma adjustment. Fuser unit 2 Is the pressure between the fuser Check the pressure removal parts roller and lower heat ro ll er p r oper? and pressure mechanism. 3 Is the thermos[...]

February 2002 © T OSHIBA TEC 4 - 73 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures Scanner 1 Is the scanner bedewed? Clean it. Dr um 2 Is the drum bedewed or dirty? Wipe the drum with dry cloth. * Be sure never use alcohol or other orga- nic solvents because the y hav e bad effect on the drum. (7) Blurred image Feeding directio[...]

FC-210/310 TROUBLESHOOTING 4 - 74 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Heater lamp unlighted Pressure between fuser rol ler and low- er heat roller improper Ther mistor , LGC board P aper 1 Is poor contact at the terminal point? 2 Is the heater lamp open-circuited? 3 Are the pressure springs working properly? 4 Is [...]

February 2002 © T OSHIBA TEC 4 - 75 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures High-v oltage transformer (transf er roller/ developer bias) Processing unit (EPU)/ de veloper unit set position De veloper drive system Dev eloper material De veloper pole position Doctor blade position Dr um Harnesses for SCM, SYS, IMG, IMC and[...]

FC-210/310 TROUBLESHOOTING 4 - 76 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures 1 Does the exposure lamp light? 2 Is the main charger securely installed? 3 Is the main charger wire open-circuited? 4 Is the high-voltage transformer output def ective? 5 Are the connectors securely connected? Is any harness between the boards [...]

February 2002 © T OSHIBA TEC 4 - 77 FC-210/310 TROUBLESHOOTING 1 Is there foreign matter or dust on the slit glass? 2 Is there foreign matter on the charger grid? 3 Is there foreign matter inside the doctor blade? 4 Is there foreign matter on the drum seal? 5 Is the drum seal of developer unit in proper contact with the drum? 6 Is there any abnorm[...]

FC-210/310 TROUBLESHOOTING 4 - 78 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Main charger Drum Discharge lamp Developer unit Drum and scanner drive systems High-voltage transformer (main charger and transfer roller) 1 Is there foreign matter on the charger? 2 Is terminal contact poor? 3 Is there any abnormalities on the [...]

February 2002 © T OSHIBA TEC 4 - 79 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures Cassette LCF Paper feed roller Rollers Registration roller Pre-registration guide Original scale 1 Is the cassette or LCF properly installed? 2 Is too much paper loaded in the cassette or LCF? 3 Is the paper corner folded? 4 Are cassette or LCF s[...]

FC-210/310 TROUBLESHOOTING 4 - 80 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Scanner Main charger Cleaner Fuser unit Drum Laser optical unit 1 Is there foreign matter in the optical path? 2 Is there dust or stain on the shading correction plate? 3 Is there foreign matter on the charger grid? 4 Is the charger grid dirty o[...]

February 2002 © T OSHIBA TEC 4 - 81 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures Main charger Fuser unit High-voltage tr ansformer (main charger/ transf er roller) Dr um Scattered toner recov e- r y roller of de veloper unit Scanner carriage section 1 Is the charger wire dirty or deformed? 2 Is the fuser belt, lower heat roll[...]

FC-210/310 TROUBLESHOOTING 4 - 82 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Dev eloper unit/ T oner car tridge Main charger High-voltage tr ansformer (main charger/ dev elo- per bias/transf er roller) Dev eloper mater ial 1 Is the toner density of developer material proper? 2 Is the doctor-sleeve gap proper? 3 Is there [...]

February 2002 © T OSHIBA TEC 4 - 83 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures T ransf er belt P aper Registration roller High-voltage tr ansformer (transf er roller) 1 Is the transfer belt dirty? 2 Is the transfer belt in proper contact with the drum ? 3 Is there any deformation or abnormali- ties on the transfer belt? 4 I[...]

FC-210/310 TROUBLESHOOTING 4 - 84 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Main charger T ransf er belt Laser optical unit Discharge lamp Developer unit Scanner section 1 Is the main charger dirty? 2 Is the transfer belt dirty? 3 Is the transfer belt in proper contact with the drum? 4 Is there any abnormalities or defo[...]

February 2002 © T OSHIBA TEC 4 - 85 FC-210/310 TROUBLESHOOTING 1 Is the “ADD T ONER” symbol flashing? 2 Is there enough toner in the cartridge? 3 Is the toner density of developer material too low? 4 Is the toner motor malfunctioning? 5 Are there any abnormalities in the toner cartridge? 6 Is the developer material life ended? 7 Is the magneti[...]

FC-210/310 TROUBLESHOOTING 4 - 86 F ebr uary 2002 © TOSHIBA TEC Cause/Section Step Check items Measures Adjustment error of scanner or printer section Registration roller P aper feed motor Pre-registration guide 1 Is same dislocation on every copy? 2 Is the registration roller dir ty , or the spring out of place? 3 Is the registration motor mal- f[...]

February 2002 © T OSHIBA TEC 4 - 87 FC-210/310 TROUBLESHOOTING If proper , perform step 1 to 3; otherwise per- form step 4 and after . Check the registration roller section and its springs. Check the drive system and replace the transf er belt if necessar y . Check the drive system. Replace the fuser belt, upper/lower heat rollers and fuser roller[...]

FC-210/310 TROUBLESHOOTING 4 - 88 F ebr uary 2002 © TOSHIBA TEC 1 Is the s pecified developer material used? 2 Is there paper dust on the cleaning blade edge? 3 Is the cleaning blade peeled? 4 Is toner recovery defective? 5 Is the cleaning roller or the oil roller damaged or their life ended? 6 Is there any bubble-like defect on the fuser belt (22[...]

February 2002 © T OSHIBA TEC 4 - 89 FC-210/310 TROUBLESHOOTING Cause/Section Step Check items Measures Original glass Main charger wire Discharge lamp Scanner Exposure lamp 1 Is the original glass dirty? 2 Is the main charger wire dirty? 3 Is the discharge lamp dirty? 4 Are the reflector , exposure lamp , mirrors, lens, etc. dirty? 5 Is the exposu[...]

FC-210/310 TROUBLESHOOTING 4 - 90 F ebr uary 2002 © TOSHIBA TEC 1 Does the paper mode correspond to the paper type? 2 Is paper too dry? 3 Is the transfer belt in proper contact with the drums? 4 Are there any abnormalities on the belt? 5 Is the high-voltage transformer output abnormal? Cause/Section Step Check items Measures P aper T ransf er belt[...]

Februar y 2002 © TOSHIBA TEC 5 - 1 FC-210/310 UPD A TING THE FIRMWARE 5. UPD A TING THE FIRMW ARE <<Caution>> Only the minimum firmware required for updating by the PC is installed in the system control PC board (SYS board), printer control PC board (IMC board), logic PC board (LGC board) and scanner control PC board (SCM board) provid[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 2 F ebr uar y 2002 © TOSHIBA TEC 5.1 Installing Software for Firmware Update 5.1.1 Outline The procedure to update the software of the SYS , IMC, LGC and SCM board using the PPP (P oint-to- P oint Protocol) and FTP (File T ranfer Protocol) is described in this section. * This procedure is descr ibed based on [...]

Februar y 2002 © TOSHIBA TEC 5 - 3 FC-210/310 UPD A TING THE FIRMW ARE BAUD R A TE 115200bps D A T A BIT 8 BITS P ARITY NONE ST OP BIT 1 BIT FLOW CONTROL NONE ECHO OFF Protocol specifications between the PC and SYS board[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 4 F ebr uar y 2002 © TOSHIBA TEC 5.1.3 Dial-up networking function The settings necessar y f or the PPP are described in this section. The dial-up networking function is used to perf or m the PPP connection on the Windows 95/98. ( 1 ) Vir tual modem Since a modem is supposed to be used f or the Windows 95/98 [...]

Februar y 2002 © TOSHIBA TEC 5 - 5 FC-210/310 UPD A TING THE FIRMW ARE The Modem Wizard is opened. Check "Don't detect my modem; I will select it from a list", and click [Next]. Click [Have Disk], then select a folder in which the downloaded file has been stored.[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 6 F ebr uar y 2002 © TOSHIBA TEC Select "Direct Connection", then click [Next]. Select "Communications P or t (COM1)", then clic k [Ne xt].[...]

Februar y 2002 © TOSHIBA TEC 5 - 7 FC-210/310 UPD A TING THE FIRMW ARE Click the [Finish] b utton to complete the vir tual modem installation.[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 8 F ebr uar y 2002 © TOSHIBA TEC 5.1.4 Installing dial-up networking Y our computer might be already set up to use a network. If the Windows prompts y ou for a netw or k pass word at the star tup and if the Network Neighborhood icon appears on the Windows desktop , the network function is already set up. In t[...]

Februar y 2002 © TOSHIBA TEC 5 - 9 FC-210/310 UPD A TING THE FIRMW ARE Select "Microsoft" from the "Manufacturers" list and "Dial-Up Adapter" from the "Network Adapters" list, then click [OK]. TCP/IP Protocol components are automatically installed together with "Dial-Up Adapter".[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 10 F ebr uar y 2002 © TOSHIBA TEC 5.1.5 Setting dial-up networking Double-clic k "My Computer". If the "Dial-Up Networking" icon is not in the window , open [Add/Remov e Programs] in the Control P anel to install it. Double-click "Dial-up Networking" and then "Make New Conne[...]

Februar y 2002 © TOSHIBA TEC 5 - 11 FC-210/310 UPD A TING THE FIRMW ARE Enter a name in the bo x "T ype a name f or the computer y ou are dialing", and then select "Direct Con- nection" for "Select a de vice". Then, click [Configure]. Click the "Gener al" tab in the "Direct Connection Proper ties" [...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 12 F ebr uar y 2002 © TOSHIBA TEC Click the "Connection" tab , confir m that no item in "Call pref erences" is selected, and then click [Ad- vanced]. Confirm that no item in the "Advanced Connection Settings" dialog box is selected. Click the [OK] button to return to the "Ma[...]

Februar y 2002 © TOSHIBA TEC 5 - 13 FC-210/310 UPD A TING THE FIRMW ARE Enter "#39" in the "T elephone number" bo x. Select an appropriate country code, then click [Next]. Click [Finish] to complete the setting for the "Dial-up Networking".[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 14 F ebr uar y 2002 © TOSHIBA TEC 5.1.6 Installing software for FTP server Install free software [W ar FTP Daemon V ersion 1.65] to use it as an FTP ser ver . W ar FTP Daemon can be downloaded from the f ollowing website . FTP: ftp://ftp.jgaa.com/pub/pr oducts/Windows/W arFtpDaemon/1.6_Series/war d165.exe HTT[...]

Februar y 2002 © TOSHIBA TEC 5 - 15 FC-210/310 UPD A TING THE FIRMW ARE Click [Add] and type in "dppc" in the "New name" box. T ype in "dppc" in the "New P ass word" and "V erify Pass word" bo xes , then click [OK]. Select "dppc" and click the "File Access" tab . Then, click [Ad[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 16 F ebr uar y 2002 © TOSHIBA TEC Double-click "Webshare". Check the "Read", "Write", "Delete", "Execute", "List", "Create" and "Remove" boxes. Confirm that the check marks are not gray but black. Check "Root", "Hom[...]

Februar y 2002 © TOSHIBA TEC 5 - 17 FC-210/310 UPD A TING THE FIRMW ARE Enter the "ONLINE" mode by clic king the b utton before star ting the fir mware update .[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 18 F ebr uar y 2002 © TOSHIBA TEC 5.2 Operation Procedure in [3][9] Mode 5.2.1 Outline Connect the copier and PC with a serial cable and turn ON the power while pressing the digital keys [3] and [9] simultaneously to star t the "Firmware Update Mode". The system fir mware , UI data and engine firmwa[...]

Februar y 2002 © TOSHIBA TEC 5 - 19 FC-210/310 UPD A TING THE FIRMW ARE ( 2 ) New file Prepare files for updating in the PC. Ne w files with the preset director y and names are provided in the f ollowing f older . C: WEBSHAREFTPROO T ( 3 ) Connection between the SYS board and PC The SYS board and PC are connected with a cross cable. F or the PC [...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 20 F ebr uar y 2002 © TOSHIBA TEC Enter "#39" in the "Phone number" box. Firmware Version Up Mode > Make a connection from PC. 5.2.3 Updating firmware Update the firmware in the [3][9] mode as follows: 1. T ur n ON the power of the copier while the digital k eys [3] and [9] are pressed [...]

Februar y 2002 © TOSHIBA TEC 5 - 21 FC-210/310 UPD A TING THE FIRMW ARE 4. The f ollowing is display ed if the serial connection was completed successfully . Y ou can press [HELP] to confir m the current v ersion (the version bef ore the copier is updated). *The engine firmware version cannot be displayed in this screen. Use the setting mode to co[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 22 F ebr uar y 2002 © TOSHIBA TEC Code Language Co de Language 2 Japanese 1 3 F innish 3 American English 1 4 Norwegian 4 English 1 5 Australian English 5 — 1 6 P olish 6 F rench 17 Czech 7 German 1 8 Greek 8 Swedish 1 9 Romanian 9 Dutch 2 0 Bulgarian 1 0 Italian 2 1 P or tuguese 1 1 Spanish 2 2 Hungarian 1[...]

Februar y 2002 © TOSHIBA TEC 5 - 23 FC-210/310 UPD A TING THE FIRMW ARE 5. Select the area to be updated using the digital ke ys and [INTERR UPT] ke y . (Press the [INTERR UPT] k ey to enter "#".) The selected number is displa yed at upper right of the screen, ne xt to "T arget:". The relation between the selected number and ar[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 24 F ebr uar y 2002 © TOSHIBA TEC In case of target #1 - #5 Firmware Version Up Mode Target:#1 Installing a new firmware. — reading a file. Target Version code l installing Displays the area being processed. Firmware Version Up Mode Target: 1 Installing new firmware. — reading a file. 6. The copier star t[...]

Februar y 2002 © TOSHIBA TEC 5 - 25 FC-210/310 UPD A TING THE FIRMW ARE V ersion of the firm w are installed Firmware Version Up Mode Target: 1 Firmware version up completed. Version: 001.003 code:U > Press START key to continue. 7. The follo wing will be display ed when the fir mw are update is completed successfully . In case of target 1 - 13[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 26 F ebr uar y 2002 © TOSHIBA TEC Firmware Version Up Mode Target: 1 Failed to install a new firmware. – file read error. Error messages - file read error . - file inf or mation error . - unfit device. - device er ase error . - de vice write error. - v er ify error . - cannot set NvRAM flags. - Communicatio[...]

Februar y 2002 © TOSHIBA TEC 5 - 27 FC-210/310 UPD A TING THE FIRMW ARE * If an error occurs while the processing of automatically sequenced writing of #4, do the following operations after completing the update in a recovery mode. T arget Area of error Operation # 4 1~10 A ft e r completing the update to the target 10 in a recovery mode, update t[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 28 F ebr uar y 2002 © TOSHIBA TEC Firmware Version Up Mode Cannot connect with PC. Failed to install a new firmware. P ower ON Connection failed Connection made successfully Number of area to be updated Target: 1 on with PC. Target: 6 on with PC. Target: #1 on with PC. Display changes corresponding to the key[...]

Februar y 2002 © TOSHIBA TEC 5 - 29 FC-210/310 UPD A TING THE FIRMW ARE In case of target 1 - 13 : Firmware Version Up Mode Target: 1 Installing a new firmware. – reading a file. 1 Press the [ST AR T] ke y Installed successfully Installation failed 3 2 2 Press the [ST AR T] ke y 1 2 Press the [ST ART] k ey Press the [CLEAR] key V ersion of the f[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 30 F ebr uar y 2002 © TOSHIBA TEC In case target of #1- #5: 1’ 3’ 2’ P ower OFF 2’ P ower OFF Area whose updating process was canceled Firmware Version Up Mode Target:#1 Installing a new firmware. – reading a file. Target version code l installing Status of updating process – reading a file. – c[...]

Februar y 2002 © TOSHIBA TEC 5 - 31 FC-210/310 UPD A TING THE FIRMW ARE Firmware Version Up Mode Target: 1 Failed to install a new firmware. – file read error. Installation failed In case of target of 1 - 13: In case of target #1 - #5: 3’ Error messages – file read error . – file inf or mation error . – unfit device. – de vice erase er[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 32 F ebr uar y 2002 © TOSHIBA TEC PC board System control PC board (SYS board) Logic PC board (LGC board) Scanner control PC board (SCM board) Printer control PC board (IMC board) 5.3 Updating the Firmware Using the Downloading Jig In this model, it is possible to update the firmware automatically by connecti[...]

Februar y 2002 © TOSHIBA TEC 5 - 33 FC-210/310 UPD A TING THE FIRMW ARE 5.3.1 System firmware ( 1 ) ROM type There are two types of ROM to be downloaded. (a) ROM for application downloading The area in the FROM on the SYS board is updated. This ROM is used f or the normal update. The data to be overwritten by this ROM are as follows. • System so[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 34 F ebr uar y 2002 © TOSHIBA TEC T ur n ON the power (do wnloading is automatically star ted). Note: Do not turn OFF the power during the downloading. The processing status is displayed on the control panel during the downloading. ( 3) Procedure of downloading (a) Connect the jig and perform downloading Atta[...]

Februar y 2002 © TOSHIBA TEC 5 - 35 FC-210/310 UPD A TING THE FIRMW ARE “Update Completed!!” is displayed on the control panel when the downloading is completed. T ur n OFF the power of the copier and disconnect the do wnloading jig. Note: Check the f ollowing in case that the do wnloading was not performed successfully . • Check if the R OM[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 36 F ebr uar y 2002 © TOSHIBA TEC (b) Confirmation of the downloaded data Check each data version when the downloading is completed to confirm that the downloading was perf or med correctly . Check the v ersion in the setting mode (08). Confir m that the version n umbers shown by entering the following codes [...]

Februar y 2002 © TOSHIBA TEC 5 - 37 FC-210/310 UPD A TING THE FIRMW ARE ( 4 ) Screens displayed during the download (a) Application downloading The screens change as follows during the application downloading. Download Board Firmware Update Mode Download Board -> FROM Update Start. Check Devices - Update FROM - Data Check - Download Board Firmw[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 38 F ebr uar y 2002 © TOSHIBA TEC Download Board Firmware Update Mode Download Board -> Hard Disk UI data Update Start. HDD Initialize - Update HDD - Data Check - Download Board Firmware Update Mode Download Board -> Hard Disk UI data Update Start. HDD Initialize - Completed Update HDD - Completed Data [...]

Februar y 2002 © TOSHIBA TEC 5 - 39 FC-210/310 UPD A TING THE FIRMW ARE 5.3.2 Engine firmware The procedure to update the engine firmware (engine ROM/LGC board, scanner ROM/SCM board and printer ROM/IMC board) is described in this section. ( 1 ) Jig board The engine ROM/LGC board uses K-PW A-DLS-320, the scanner R OM/SCM board and the pr inter ROM[...]

FC-210/310 UPDA TING THE FIRMW ARE 5 - 40 F ebr uar y 2002 © TOSHIBA TEC (2 ) Downloading ( a ) Attach the ROM to the jig board and connect the board with the jig connector of the copier . <<Engine ROM/LGC board>> 1. T ake off the rear co ver . ( Ser vice Manual ch. 2.5.1) 2. Connect the downloading jig with the jig connector on the LG[...]

Februar y 2002 © TOSHIBA TEC 5 - 41 FC-210/310 UPD A TING THE FIRMW ARE Jig connector ( b ) T u r n ON the po wer while [0] and [8] are pressed simultaneously (downloading is automatically star ted). (c ) T ur n OFF the power when the LED on the jig board star ts flashing. Remov e the downloading jig. ( d ) Check the version of the ROM in the sett[...]

Februar y 2002 © TOSHIBA TEC 6 - 1 FC-210/310 POWER SUPPL Y UNIT 6. PO WER SUPPL Y UNIT 6.1 Output Channel There are four output channels which are not link ed with the door s witches, as shown below . (1) 3.3V(M) — For MPU on the SYS board, the image processing circuit, etc. 3.3V A : Pins 4 and 5, J707 Output to: IMC board, SYS board, AI board [...]

FC-210/310 POWER SUPPL Y UNIT 6 - 2 February 2002 © TOSHIBA TEC There are two output channels which are link ed with the door sw itches. (1) 5.1V(D) — F or the laser diodes and the laser drivers 5.1V A : Pin 7, J702 Output to: LGC board 5.1VB : Pin 3, J705 Output to: IMC board, RL Y board (via the IMC board), LDR board (via the IMC board) (2) 24[...]

Februar y 2002 © TOSHIBA TEC 6 - 3 FC-210/310 POWER SUPPL Y UNIT <Fuse rating> F 1 12A/125V Pr imar y side F 2 12A/125V F 3 12A/125V Secondar y side F 5 4A/125V F 6 4A/125V F 7 5A/125V F 8 4A/125V F 9 5A/125V F 1 0 4A/125V ICP3 12A/125V ICP4 3A/125V ICP5 3A/125V ICP6 3A/125V[...]

FC-210/310 POWER SUPPL Y UNIT 6 - 4 February 2002 © TOSHIBA TEC 2 24VF SCM N.F N.F N.F J702 J703 J704 J705 J711 J706 J707 J708 J709 J710 1 24VA LGC 2 24VB LGC 3 24VC LGC 4 DGA LGC 5 DGB LGC 6 DGC LGC 7 5.1VA LGC 8 LGC 1 24VD DEV-MOT 2 24VD DEV-MOT 3 24VD DEV-MOT 4 DGD DEV-MOT 5 DGD DEV-MOT 6 24VE FED-MOT 7 24VE FED-MOT 8 DGE FED-MOT 9 DGE FED -MOT[...]

FC-210/310 WIRE HARNESS CONNECTION DIAGRAMS 7 - 1 F ebr uar y 2002 © T OSHIBA TEC 7. WIRE HARNESS CONNECTION DIA GRAMS[...]

FC-210/310 WIRE HARNESS CONNECTION DIAGRAMS 7 - 3 Februar y 2002 © T OSHIBA TEC Fuse Thermostat SSR-U SSR-L UP -LAMP LOW -LAMP MAIN-SW FRNCV -SW LEFCV -SW MAIN-SW PS-A CC J701-1 J701-3 J701-6 J701-4 Upper thermostat Lower thermostat SCN J614-7 J614-2 J614-6 J614-3 J321-5 J616-2 WHITE WHITE BLUE BLUE WHITE WHITE WHITE WHITE BLACK BRO WN BLACK BLACK[...]

PWA-F-LGC PWA-F-IMC-314 PWA-F-SCM PS-ACC PWA-F-IMG-314 PWA-F-SYS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 35 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 [...]

Februar y 2002 © T OSHIBA TEC A - 1 FC-210/310 SPECIFICA TIONS <Appendix> SPECIFICA TIONS · A CCESSORIES · OPTIONS · SUPPLIES 1. Specifications • Copy process Indirect electrophotographic process (dry) • T ype Console type • Original table Fix ed table (the left rear corner used for Standard original placement) • Acceptab le origi[...]

FC-210/310 SPECIFICA TIONS A - 2 F ebruary 2002 © TOSHIBA TEC * V alues in parentheses ( ) are the copy speed in the b lack mode cop ying. * “–” means “not a v ailable”. * The cop y speeds listed are av ailable when originals are manually placed f or single-side, multiple cop ying. * When the document f eeder is used, the cop y speed of [...]

Februar y 2002 © T OSHIBA TEC A - 3 FC-210/310 SPECIFICA TIONS Cassette Duple x copy LCF Bypass cop y Remarks Size A3~A5R A4, L T A3~A5-R I n the bypass mode, LD~ST -R LD~ST -R either irregular sizes or arbitrary sizes can be set. W eight 64~163g/m 2 64~105g/m 2 64~163g/m 2 64~256g/m 2 17lb~60lb .cov er 17~28 lb . 17lb~60lb .cov er 17lb~140lb .ind[...]

FC-210/310 SPECIFICA TIONS A - 4 F ebruary 2002 © TOSHIBA TEC Mo de P ow er Consumption W ar m-up time Efficiency Le vel 1 Appro x.100W Approx. 2 min 30 sec. Approx. 56% Energy saving mode (Appro x.135W) (Appro x. 48%) 115V series Le vel 2 Approx.160W Appro x. 1 min 15 sec. Appro x. 29% (Appro x.195W) (Appro x . 25%) Nor mal standb y Approx. 225W [...]

Februar y 2002 © T OSHIBA TEC A - 5 FC-210/310 SPECIFICA TIONS 2. Accessories Setup instructions 1 pc. Operator’ s manual 1 pc . (not av ailable f or MJD) Color cop y guide 1 pc. (not availab le f or MJD) PM stick er 1 pc. (for MJD) Setup repor t 1 set. (for NAD and MJD) CS card 1 pc. (f or MJD) D ru m 4 pcs. Operator’ s manual pock et 1 pc. D[...]

FC-210/310 SPECIFICA TIONS A - 6 F ebruary 2002 © TOSHIBA TEC 3. Options Platen cov er KA-2060PC A utomatic document feeder (RADF) MR -3006A, MR-3006E A utomatic duplexing unit (ADU) MD-5007 Cassette module MY -1020 Slot cov er KE-FC22 Large capacity f eeder (LCF) MP-1503L T ,MP1503A4 Finisher MJ-1019, MJ-1020 (with saddle stitching function) Hole[...]

Februar y 2002 © T OSHIBA TEC A - 7 FC-210/310 SPECIFICA TIONS 5. System List AI board KR-2030 Control panel kit f or built-in controller KR-8006 Finisher MJ-1019 Staple car tridge ST APLE-700 Automatic document f eeder MR-3006A, MR-3006E Platen cov er KA-2060PC K ey cop y counter MU-8, Sock et MU-10 Work table KK-2460 Work tab le kit KN-FC22W01 A[...]