Toshiba FT-8001 AW инструкция обслуживания

[...]

1 IMPORT ANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wa[...]

2 13. Do not use the telephone in the vicinity of a gas leak. CAUTION: TO REDUCE THE RISK OF FIRE OR INJUR Y TO PERSONS BY THE BA TTERY , READ AND FOLLOW THESE INSTRUCTIONS. 1. Use only the appropriate type and size battery pack specified in the instruction manual provided for this product. 2. Do not dispose of the battery pack in a fire. The cell [...]

3 SER VICE REQUIREMENTS If the cordless telephone should malfunction, or need changes or modifications, all repairs will be performed by an authorized T oshiba Service Station. This unit has been registered with the FCC for direct connection to the telephone network. Under the FCC program, no customer is authorized to repair this unit. This applies[...]

4 INTRODUCTION T oshiba America Consumer Products, Inc. takes pride in presenting your phone, one of the finest cordless telephones available. Intelligent design, superb craftsmanship, and the latest technological advances have been combined to provide you with a telephone that is easy to operate and will provide you with years of dependable servic[...]

5 INST ALLA TION 1. SETTING UP THE BASE UNIT For use on a desk or counter top follow the instructions below . DESKTOP MOUNTING: • USE ONL Y WITH Supplied AC ADAPTOR (T AC-8001); power source AC 120V , 60Hz/DC 9V). • The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use). Raise the antenna to ve[...]

6 Red Black 2. CHARGE THE BA TTER Y P ACK Note Use only the supplied battery pack (TRB-8000 power source 600 mAh, 3.6V). q Remove the battery compartment cover on the back of the handset by sliding it down. w Plug the battery pack cord into the connector in the battery compartment by observing the correct polarity . It fits in only one way . e Plac[...]

7 After the battery pack is fully charged; Operation Approx. battery life While in use (T alk mode) up to 7 hours While not in use (Standby mode) up to 14 days When T ALK/BA TT LOW LED blinks, all handset buttons are disabled and the battery needs to be charged. If this occurs during a call, you hear short beeps. Finish the call as soon as possible[...]

8 Wall mount template IMPORTANT: Before mounting, select a wall area of sufficient strength. If mounting on wallboard or in an area of questionable strength, locate a stud for maximum support of your telephone. Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard. CUT CUT • • • Route the cords [...]

9 LOCA TIONS OF CONTROLS HANDSET CONTROLS BASE UNIT CONTROLS Antenna Charging Contacts RDL/P (Redial/Pause) button DC IN 9V jack LINE Modular jack Antenna PAGE button Charging Contacts IN USE/CHARGE LED Speed Dial Index Card (back) Write down numbers stored in memory . Rechargeable Battery Pack (back) TALK button Dialpad TONE/ (T one) button FLASH [...]

10 Please see “LOCA TION OF CONTROLS” for the location of each button used for the following operations. SETTING THE DIAL MODE Most phone systems use tone dialing. But, to use tone dialing, you must have a tone service dialing system supplied by your telephone company . Then you must set your telephone dial mode for the type of service you have[...]

11 MAKING A CALL 1. MAKING A CALL q Press TALK . The T ALK/BA TT LOW LED will light. w Listen for the dialtone. e Key in the phone number you are calling. r T o hang up, press TALK again or place the handset on the base unit. The T ALK/BA TT LOW LED turns off. 2. ANSWERING A CALL q Simply pick up the handset or press any key if the handset is locat[...]

12 3. INTERFERENCE OR ST A TIC If you hear noise during a call, press CH to select another channel. The T ALK/BA TT LOW LED blinks while changing a channel. 4. CHANGING THE RINGER VOLUME Press VOL/RING to select one of four ringer tone and volume combinations during standby mode. Each time you press VOL/RING , the setting will change. 5. CHANGING T[...]

13 8. SENDING TONE SIGNAL (for Pulse service user) Even if you have Pulse service (the dial mode is set to Pulse), you can use this phone with banking and other phone services requiring touch tone signals. q Dial the service number and wait for the connection. w Press TONE/ , then enter the numbers required. Y ou will hear the tones on the line. 9.[...]

14 MEMOR Y DIALING Y ou can store up to 10 telephone numbers in memory . Notes In memory dialing operation, • If more than 20 seconds elapse between pressing buttons, the operation will be cancelled and you must start over again. • If you press a wrong button, an error tone sounds and the handset returns to standby mode. • If a call comes in,[...]

15 Replacing a telephone number Just store the new number following the same steps in “ 1. ST ORING NUMBERS. ” The new number will replace the previously stored one. 2. DIALING A ST ORED NUMBER q Pick up the handset and press TALK . The T ALK/BA TT LOW LED lights. w Press MEM . e Enter the memory address (0 to 9). The stored number will be dial[...]

16 ACCESSORIES Rechargeable Battery pack (1) TRB-8000 Part # RC004931 AC Adaptor (1) T AC-8001 Part # RC009790 for FT -8001 T AC-8001 Part # RC009791 for FT -8001W T elephone Cord (1) Part # RC008231 W all Mount Bracket (1) Part # RC009245 for FT -8001 Part # RC009246 for FT -8001W Owner ’ s Manual (1) Part # RC012151 Speed Dial Index Card (1) Pa[...]

17 TROUBLESHOOTING GUIDE Should any problem occur with the set, make the following simple tests to determine whether or not servicing is required. PROBLEM The handset battery does not charge. Battery becomes low quickly . Can not make or receive calls. Can not hear the dial tone. T ALK/BA TT LOW LED blinks in the standby mode. SOLUTION • The char[...]

PROBLEM The handset does not ring or receive a page. CHARGE LED does not light when the handset is placed on the base. Noise or interference. The unit does not operate properly . When the handset is returned to the base unit with the volume level set at High, a momentary squeal or howling sound may sometimes be heard. SOLUTION • The handset is lo[...]

UCZZ01337BZ RC012151 Printed in China © 2001 TOSHIBA AMERICA CONSUMER PRODUCTS. INC. All warranties implied by state law , including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the dura tion of the limited warranties set forth above. With the e xception of any warranties implied by state[...]