Toshiba IK-WB70A инструкция обслуживания

For information on our latest products and peripheral devices, refer to the following Website: ■ http://www.toshibasecurity.com The above URL is subject to change without prior notice. If the URL changes, refer to the Toshiba website (http://www.toshiba.com). NETWORK CAMERA Model: IK-WB70A User's Manual 㪉㪍㩷㪆㩷㪈㪍㪇[...]

2 Installation Appendix Configuration Definitions Introduction How to Use Introduction FCC (USA)-INFORMATION NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the e[...]

3 Installation Appendix Configuration Definitions Introduction How to Use Thank you for purchasing the IK-WB70A Network Camera. Before yo u start using the camera, read this User's Manual carefully to ensure correct usage. Once you have finished reading this User's Manual, keep it in a convenien t place for future reference. The design[...]

4 Installation Appendix Configuration Definitions Introduction How to Use IMPORTANT SAFEGUARDS 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. Warnings Comply with all warnings on the product and [...]

5 Installation Appendix Configuration Definitions Introduction How to Use CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of u[...]

6 Installation Appendix Configuration Definitions Introduction How to Use NOTES ON USE AND INSTALLATION Do not aim the camera at the sun • Never aim the camera at the sun even with the camera power off. Do not shoot intense light • Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. Howev[...]

7 Installation Appendix Configuration Definitions Introduction How to Use Precautions for Use Disclaimer We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user in any of the following cases: 1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether intentional[...]

8 Installation Appendix Configuration Definitions Introduction How to Use Be sure to use only the supplied AC adapter. Using a different AC adapter may cause the camera to malfunction, heat up, or catch fire. Before using the AC adapter, carefully read and observe the Important Safety Instru ctions ( → page 4) and the notes below. Plug the AC a[...]

9 Installation Appendix Configuration Definitions Introduction How to Use Specifications AC adapter (DSA-20P-10) Power source : 100-240 VAC 50/60 Hz Rated output : 12 VDC, 1.5 A Ambient temperature guaranteed for performance : 32F to 104F (0℃ to 40℃） Storage temperature : -4F to 140F (-20℃ to 60℃） Maximum external dimensi[...]

10 Installation Appendix Configuration Definitions Introduction How to Use Table of Contents Introduction Introduction ● ....................................................................................................................................... 2 IMPORTANT SAFEGUARDS ● ..............................................................[...]

11 Installation Appendix Configuration Definitions Introduction How to Use Contents ● IK-WB70A ● Shade ● Screws / RJ45 female/female coupler ● Mounting bracket ● AC adapter ● Silica gel / Wrench ● I/O Connectors ● Quick Start Guide and Important Safeguards ● Warranty ● CD-ROM IK-WB70A The above URL is subject to change without[...]

12 Installation Appendix Configuration Definitions Introduction How to Use Physical description Front panel IR LED Lens Illuminance sensor Connectors Ethernet 10/100 RJ45 plug Audio output (green) mini-jack Microphone input (pink) mini-jack Power cord socket (black) General I/O terminal block GND Cable length: approx. 39 inches (1000 mm) General [...]

13 Installation Appendix Configuration Definitions Introduction How to Use 1 2 3 Alarm switch 4 1: +12 V 12 VDC Output 2: DO Digital Output 3: DI Digital Input 4: GND Ground The connection definition is as below when "Digital input" is used for alarm input. Internal Circuit Signal Condition Digital Input W( - - +1+0 ?[...]

14 Appendix Confi guration Defi nitions Introduction Installation How to Use Installation In this user's manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can confi gure the Network Camera and grant user access to the camera. Hardware installation PO W ER C OL[...]

15 Installation Appendix Configuration Definitions Introduction How to Use Network deployment Setup the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection. 1. If you have external devices such as sensors and alarms, make connection from general I/O terminal block. 2. Use the suppl[...]

16 Appendix Configuration Definitions Introduction Installation How to Use Installation (Cont.) 2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192.168.0.3, please forward the following ports for the Network Camera on the gateway. ■ HTTP port ■ RTSP port ■ RTP port for audio ■ RTCP port for audio ■ [...]

17 Installation Appendix Configuration Definitions Introduction How to Use Set up the Network Camera through Power over Ethernet (PoE) When using a PoE hub The Network Camera is PoE-compliant, which allows it to be powered via a single Ethernet cable. If your hub or gateway supports PoE, refer to t he following illustration to connect the Network[...]

18 Appendix Confi guration Defi nitions Introduction Installation How to Use Installation (Cont.) Installation Wizard Software installation Installation Wizard (IW), a free-bundled software packaged in the product CD, helps to set up your Network Camera in a LAN. 1. Install the IW under the Software Utility directory from the software CD. Double [...]

19 Installation Appendix Configuration Definitions Introduction How to Use This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices. Using web browsers 1. Launch your web browser (ex. Microsoft ® Internet Explorer ® ). 2. Enter the IP address of the Network Camera in the address ?[...]

20 Appendix Configuration Definitions Introduction Installation How to Use Initial Access to the Network Camera (Cont.) NOTE By default, the Network Camera is not password-protected. To prevent unauthorized ● accesses, it is highly recommended to set a password for the Ne twork Camera. For more information about how to enable password protectio[...]

21 Installation Appendix Configuration Definitions Introduction How to Use Using 3GPP-compatible mobile devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed from the Internet. For more information on how to set up the Network Camera over the Internet, refer to Se tup the Network [...]

22 Installation Appendix Configuration Definitions Introduction How to Use Main Screen with Camera View This chapter explains the layout of the main page. It is composed of the following four sections: Toshiba logo, Menu, Camera Name, and Live Video Window. Camera name Live view window Menu Toshiba logo Toshiba Logo Click this logo to visit the T[...]

23 Installation Appendix Confi guration Defi nitions Introduction How to Use Live Video Window The following window is displayed when the video mode is set to MPEG-4: T ime and date Video title T itle, time and date MPEG-4 protocol and media options Video and audio control buttons IP7142 16:38:01 2008/01/03 IK-WB70A(TCP-AV) Video title: The video[...]

24 Installation Appendix Confi guration Defi nitions Introduction How to Use Main Screen with Camera View (Cont.) Resume: Resume the transmission of streaming media. The button becomes Pause button after clicking the Resume button. Stop: Stop the transmission of streaming media. Click the Resume button to continue transmission. Volume: When the m[...]

25 Installation Appendix Confi guration Defi nitions Introduction How to Use Start MP4 recording: Click this button to record video clips in MP4 fi le format to your computer. Press the Stop MP4 recording button to end recording. When you quit the web browser, video recording stops accordingly. To specify the storage destination and the fi le[...]

26 Installation Appendix Configuration Definitions Introduction How to Use Client Settings This chapter explains how to select the streaming source, transmission mode and saving options at the client computer. It is composed of the following four sections: Stream Options, MPEG-4 Media Options, MPEG-4 Protocol Options and MP4 Saving Options. When [...]

27 Installation Appendix Confi guration Defi nitions Introduction How to Use TCP: This protocol guarantees the complete delivery of streaming da ta and thus provides better video quality. The downside with this protocol is that its real-time eff ect is not as good as that of the UDP protocol. HTTP: This protocol allows the same quality as TCP pr[...]

28 Installation Appendix Introduction How to Use Configuration Definitions Configuration Definitions Only Administrators can access the system configuration page. Ea ch category in the menu will be explained in the following sections. System Parameters This section explains how to configure the basic settings for the Network. It contains the [...]

29 Installation Appendix Introduction How to Use Configuration Definitions Enable Daylight Saving Time: Select this option to enable daylight savings time (DST). During DST, the system clock moves one hour ahead. Set the time zone for your Network Camera first if using this feature. The starting time and ending time of the DST is displayed upon [...]

30 Installation Appendix Introduction How to Use Configuration Definitions Configuration Definitions (Cont.) Security Settings This section explains how to enable password protection and create multiple accounts. It contains the following three segments: Root Password, Add User and Manage User. Root Password The administrator account “root”[...]

31 Installation Appendix Introduction How to Use Configuration Definitions HTTPS This section explains how to enable authentication and encrypted communication over SSL. Enable HTTPS Select this options to turn on the HTTPS communications. Select either “HTTP & HTTPS” or “HTTPS only.” Select the method to create a certificate before [...]

32 Installation Appendix Introduction How to Use Configuration Definitions Configuration Definitions (Cont.) Create and Install Certificate Select either to create a self-signed certificate or a signed certificate. To create a self-signed certificate automatically. 1. Click “Create self-signed certificate automatically.” 2. Click Save.[...]

33 Installation Appendix Introduction How to Use Configuration Definitions 2. Fill in the information required for generating a Certificate Signed Request (CSR) and click Save. 3. Here is an example of a CSR: 4. Click Save. Certificate Information Display the certificate information. Users may click Property for details. To remove the signed c[...]

34 Installation Appendix Introduction How to Use Configuration Definitions Security Alert Fig.1 Fig.2 Above security alert may be shown when switch between HTTP and HTTPS connection. Click OK or Yes to continue the operation. Fig.3 Fig.4 Above security alert may be shown when accessing the camera by HTTPS using “Self-Signed Certificate” , IE[...]

35 Installation Appendix Introduction How to Use Configuration Definitions Network This section explains how to configure wired network connection for the Network Camera. It consists the following five segments: Network Type, HTTP, Two way audio, FTP and RTSP Streaming. After completing the settings on this page, click Save to take effect. Netw[...]

36 Installation Appendix Introduction How to Use Configuration Definitions Configuration Definitions (Cont.) PPPoE (Point-to-point over Ethernet) Select this option to configure your Network Camera to make it accessible from a DSL Internet connection. To use this feature, requires an account provided by your ISP. Follow the steps below to acqu[...]

37 Installation Appendix Introduction How to Use Configuration Definitions 2. Click the Optional Network Components in the menu bar's Advanced. 3. In the Windows Components Wizard dialog box, select Networking Services and then click Details. 4. In the Networking Services dialog box, select Universal Plug and Play and then click OK. 5. Click[...]

38 Installation Appendix Introduction How to Use Configuration Definitions Configuration Definitions (Cont.) How does UPnP ● TM work? UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices added to a network. Services and capabilities offered by networked devices, such as printing and file sharin[...]

39 Installation Appendix Introduction How to Use Configuration Definitions To access the Network Camera within a LAN, both HTTP port and secondary HTTP port can be used to access the Network Camera. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for the Network Camera's IP add[...]

40 Installation Appendix Introduction How to Use Confi guration Defi nitions Note that as JPEG only transmits a series of JPEG images to the client, to use this feature, make sure the video mode is set to “MPEG-4” and the media option is set to “Video and Audio” . Audio send from operators Audio send to operators America Taiwan Audio is b[...]

41 Installation Appendix Introduction How to Use Configuration Definitions RTSP Streaming Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic and digest. If basic authentication is selected, the password is sent in plain text [...]

42 Installation Appendix Introduction How to Use Configuration Definitions The five ports can be changed between 1025 and 65535. The RTP port must be an even number and the RTCP port is RTP port number plus one, and thus always be odd. When the RTP port changes, the RTCP port will change accordingly. If the RTP ports are incorrectly assigned, th[...]

43 Installation Appendix Introduction How to Use Configuration Definitions DDNS This section explains how to configure dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. DDNS: Dynamic domain name service E[...]

44 Installation Appendix Introduction How to Use Configuration Definitions Access list This section explains how to control the access permission by checking the client PC's IP addresses. It contains of the following four segments: Allowed list, Denied list, Delete allowed list, and Delete denied list. Allowed list or Denied list There are t[...]

45 Installation Appendix Introduction How to Use Configuration Definitions Audio and video This section explains how to cofigure audio and video performances of the Network Camera. It contains the following two segments: Video settings and Audio settings. Video settings Video title: Enter a name that will be displayed on the title bar of the liv[...]

46 Installation Appendix Introduction How to Use Configuration Definitions Video orientation: Flip--vertically reflect the display of the live video; Mirror-- horizontally reflect the display of the live video. Select both options if the Network Camera is installed upside-down to correct the image orientation. White balance: Adjust the value for[...]

47 Installation Appendix Introduction How to Use Configuration Definitions Privacy mask Click Privacy Mask to open the Privacy Mask page. In this page, you can block out some sensitive zones for privacy concerns. IK-WB70A IK-WB70A ■ To set the privacy mask windows, follow the steps below: 1. Click New to add a new window. 2. To resize and drag-[...]

48 Installation Appendix Introduction How to Use Configuration Definitions Exposure level: You can manually set the Exposure level from 1 to 8. The default value is 4. AGC (Auto Gain Control): You can manually set the AGC level to 2X, 4X or 8X. The default value is 4X. Enable WDR (Wide Dynamic Range): Select to enable the WDR function. This Netwo[...]

49 Installation Appendix Introduction How to Use Configuration Definitions ■ Mode The Network Camera offers two choices of video compression standards for real- time viewing: MPEG-4 and MJPEG. If MPEG-4 is selected, it is streamed in RTSP or HTTP. There are four dependent parameters provided in MPEG-4 mode for video performance adjustment. ■[...]

50 Installation Appendix Introduction How to Use Configuration Definitions If JPEG mode is selected, the Network Camera continuously sends JPEG images to the clients, producing dynamic effects similar to movies. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage. [...]

51 Installation Appendix Introduction How to Use Configuration Definitions Audio settings Mute: Select this option to disable audio transmission from the Netw ork Camera to all clients. Note that if mute mode is turned on, no audio data will be transmitted to all clients even though the audio transmission is enabled in the Client Settings page. I[...]

52 Installation Appendix Introduction How to Use Configuration Definitions Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. IK-WB70A(TCP-AV) To enable motion detection, follow the steps below: 1. Click New to add a new motion detect[...]

53 Installation Appendix Introduction How to Use Configuration Definitions A green bar indicates that even though motions are detected, the event will not be triggered because the image variations are still falling under the defined threshold. Percentage = 30% NOTE How does motion detection work? ● There are two parameters for setting the moti[...]

54 Installation Appendix Introduction How to Use Configuration Definitions Camera control This section explains how to control the Network Camera's digital zoom and optional pan/tilt unit or scanner using RS485 interface. RS485 Settings Disable: Select this option to disable this function. PTZ camera: Select this option to enable PTZ operati[...]

55 Installation Appendix Introduction How to Use Configuration Definitions Preset Position Click Preset Position to open the Preset Position page. In this page, you can set the preset position for the Network Camera. A total of 20 preset positions can be configured. IK-WB70A(TCP-AV) Follow the steps below to set preset positions: 1. Adjust the N[...]

56 Installation Appendix Introduction How to Use Configuration Definitions The command button will appear in the main page as the following diagram. Configuration Definitions (Cont.) 㪏㪈㩷㪆㩷㪈㪍㪇[...]

57 Installation Appendix Introduction How to Use Configuration Definitions Application This section explains how to configure the Network Camera to rea ct in response to particular situations. A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or via Email as notifications. In the [...]

58 Installation Appendix Introduction How to Use Configuration Definitions Media name: Enter a descriptive name for the media setting. Media Type: There are three choices of media types available: Snapshot, Vi deo Clip, and System log. Snapshot: Select to send snapshots when a trigger is activated. ■ Source: Select to take snapshots from stream[...]

59 Installation Appendix Introduction How to Use Configuration Definitions ■ Maximum file size Specify the maximal file size allowed. ■ File Name Prefix Enter the text for the file name. For example: System log: Select to send a system log when a trigger is activated. When completed, click Save to take effect and then click Close to quit[...]

60 Installation Appendix Introduction How to Use Configuration Definitions Server name: Enter a descriptive name for the server setting. Server Type: There are four choices of server types available: Email, FTP, HTTP, and Network storage. Email: Select to send the media via Email when a trigger is activated. ■ Sender email address: Enter the em[...]

61 Installation Appendix Introduction How to Use Configuration Definitions HTTP: Select to send the media to an HTTP server when a trigger is activated. ■ URL: Enter the URL of the HTTP server. ■ User name: Enter the user name. ■ Password: Enter the password. To verify if the HTTP settings are correctly configured, click Test. The result w[...]

62 Installation Appendix Introduction How to Use Configuration Definitions Event In the Event section, click Add to open the event setting page. In this page, you can arrange the three elements -- Trigger, Schedule and Action to plot an event. A total of three event settings can be configured. Event name: Enter a descriptive name for the event s[...]

63 Installation Appendix Introduction How to Use Configuration Definitions ■ System boot Select this option to allow the Network Camera to trigger when the power of Network Camera is disconnected. Event Schedule: The effective period in which the event stays active. Specify the effective period for the event. ■ Select the days on weekly bas[...]

64 Installation Appendix Introduction How to Use Configuration Definitions Recording This section explains how to configure the recording settings for the Network Camera. Recording Settings Click Add to open the recording setting page. In this page, you can define the recording source, recording schedule and recording capacity. A total of two rec[...]

65 Installation Appendix Introduction How to Use Configuration Definitions Destination: Specify a storage destination for the recorded video files. Note that the destination field is empty by default. Go to Configuration > Application > Server Settings to set a Network storage server; refer to Server Settings on page 59. Max. recording c[...]

66 Installation Appendix Introduction How to Use Configuration Definitions System log This section explains how to configure the Network Camera to send the system log message to a remote server and how to refer the current log message of the Network Camera. It is composed of the following two Segments: Remote Log and Current Log. Remote Log You c[...]

67 Installation Appendix Introduction How to Use Configuration Definitions Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. Reboot This feature allows you to turn off and then turn on the Network Camera. It takes about one ∼ two minutes to complete the process. When complet[...]

68 Installation Appendix Introduction How to Use Configuration Definitions Upload or Export Daylight Saving Time Configuration File This feature allows you to set the starting time and ending time of DST. Follow the steps below to set up: 1. In t he E xp or t Da yl ig ht Sav in g T im e Co nf ig ur at io n Fi le c ol um n, click Export to export[...]

69 Installation Appendix Introduction How to Use Configuration Definitions 3. In the Upload Column, click Browse... and specify the XML file. If the incorrect date and time is assigned, you will see the following warning message when uploading the file to the Network Camera. 4. Click Upload. To enable the DST, see System Time on page 28. The fo[...]

70 Installation Appendix Introduction How to Use Configuration Definitions The upgrade is successful as you see "Reboot system now!! This connection will close". After that, re-access the Network Camera. The following message is displayed when the upgrade is succeeded. The following message is displayed when you have selected an incorre[...]

71 Installation Introduction How to Use Confi guration Defi nitions Appendix Troubleshooting Status LED The LED indicates the status of the Network Camera. Status LED Description Blinking red (two short, one long) 1. Power is being supplied to the Network Camera. 2. Restore, or reboot the Network Camera. Reboot and restore Reset button Status LED[...]

72 Installation Introduction How to Use Configuration Definitions Appendix Wrong date and time If this Network Camera is left in the low-temperature environment, the date and time of camera may be delayed when turning on the power. To prevent this trouble, it is highly recommended to leave the power ON of Network Camera in the low- temperature en[...]

73 Installation Introduction How to Use Configuration Definitions Appendix Glossary (Index) A Accessories .................................................. .... 11 Access list ......................................................... 44 Administrator .................................................... 30 Alarm setting ..........................[...]

74 Installation Introduction How to Use Configuration Definitions Appendix I Image settings ................................................. 46 Installation Wizard .......Quick Start Guide: 16 I/O terminal block ............................................. 12 IP address .......................................................... 35 Unique string[...]

75 Installation Introduction How to Use Configuration Definitions Appendix Specifications Power supply 12 VDC ± 10 %, 24 V AC ± 10 %, PoE Power consumption 12 VDC / 0.4 A, 24 V AC / 0.4 A Image pickup device 1/3.3 inch, CMOS Effective pixels Horizontal 640, vertical 480 pixels Scanning system Progr essive Minimum object illuminance 0 lux with [...]

76 Installation Introduction How to Use Configuration Definitions Appendix Appearance Diagram Dimensions: inch (mm) 1.7 (43) 1/4"-20 UNC Ǟ 1.1 (28) Ǟ 1.6 (41) 2.76 (70) 3.4 (86) 1.7 (43) 0.79 (20) 0.39 (10) 0.79 (20) Ǟ 0.18 (4.6) Ǟ 0.18 (4.6) 7.83 (199) 7.09 (180) 4.06 (103) 1.18 (30) 2.07 (52.5) 㪈㪇㪈㩷㪆㩷㪈㪍㪇[...]

77 Installation Introduction How to Use Configuration Definitions Appendix 0.9 (23) 0.9 (23) 9.49 (241) 2.4 (61) 3.19 (81) 1.97 (50) 1.38 (35) Ǟ 0.28 (7) Ǟ 0.28 (7) Ǟ 0.28 (7) Ǟ 0.28 (7) R0.14 (3.5) Ǟ 0.28 (7) 2.32 (59) 3.27 (83) 4.06 (103) 0.29 (7.3) Dimensions: inch (mm) 㪈㪇㪉㩷㪆㩷㪈㪍㪇[...]

78 Installation Introduction How to Use Configuration Definitions Appendix Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT REGARD TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES. FOR MORE IN[...]

79 Installation Introduction How to Use Configuration Definitions Appendix GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not [...]

80 Installation Introduction How to Use Configuration Definitions Appendix You may charge a fee for the physical act of transferring a cop y, and you may a t your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy an[...]

81 Installation Introduction How to Use Configuration Definitions Appendix and will automatically terminate your rights under this License . However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept [...]

82 Installation Introduction How to Use Configuration Definitions Appendix PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN N O EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL [...]

T OSHIB A AMERICA INFORMA TION SYSTEMS, INC. Sur veillance & IP Video Products 9740 Ir vine Boule vard, Ir vine, CA 92618-1697 Phone Number : (877) 855-1349 㪈㪇㪏㩷㪆㩷㪈㪍㪇[...]