Toshiba M7 инструкция обслуживания

[CONFIDENTIAL] 1 Toshiba Personal Computer Satellite R20 / TECRA M7 Maintenance Manual TOSHIBA CORPORATION File Number 960-572[...]

ii [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Copyright © 2006 by Toshiba Corporation. All rights reserv ed. Under the copyright laws, this manual cannot be reproduced in any form without the pr ior written permission of Toshiba. No patent liability is assumed, with respect to the use of the information contained herein[...]

Preface This maintenance manual describes how to pe rform hardware service maintenance for the Toshiba Personal Computer Satellite R20/TECRA M7, referred to as Satellite R20/TECRA M7 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the [...]

iv [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) The manual is divided into the following parts: Chapter 1 Hardware Overview describe s the Satellite R20/TECRA M7 system unit and each FRU. Chapter 2 Troubleshooting Procedures e xplains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to[...]

Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronym s are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operat[...]

vi [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Manual ( 960-572) Table of Contents Chapter 1 Hardware Overview 1.1 Features .................................................................................................................. .... 1-1 1.2 System block diagram ......................................................................[...]

Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-4 3.3 Setting of the hardware configuration...........................[...]

viii [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Chapter 4 Replacement Procedures 4.1 Overview ................................................................................................................... 4-1 4.2 Battery pack ...........................................................................................[...]

4.32 Hinge assembly ....................................................................................................... 4-79 4.33 Fluorescent Lamp.................................................................................................... 4-82 Appendices Appendix A Handling the LCD Module ................................................[...]

x [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572)[...]

[CONFIDENTIAL] Chapter 1 Hardware Overview[...]

1 Hardware Overview 1-ii [CONFIDENTIAL ] Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) 1 Hardware Overview[...]

1 Hardware Overview Satellite R20/TECRA M7 Maintena nce Man ual (960-572) [CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features .................................................................................................................. .... 1-1 1.2 System block diagram ..........................................................................[...]

1 Hardware Overview 1-iv [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Figures Figure 1-1 Front of the computer..................................................................................... 1-6 Figure 1-2 System un its configuration ............................................................................ 1-7 Figur[...]

1.1 Features 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-1 1 Features 1.1 Features The Satellite R20/TECRA M7 is an ultra thin and lightweigh t tablet PC r ealizing cable-less environment on a table by wireless function with an Intel ® Core TM Duo/Solo or Intel ® Celeron ® M processor realizi ng[...]

1 Hardware Overview 1.1 Features 1-2 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572)  Memory Two DDR2 SO-DIMM slots support DDR2 533 or DDR2 667. Memory modules can be installed to a maximum of 4GB (4 ,096MB). Memory modules of 256MB, 512MB, 1GB and 2GB sizes are available.  HDD The computer has a 2.5-inch SATA HDD. Th[...]

1.1 Features 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-3  Touch pad A touch pad is installed as a pointing device.  Batteries The computer has three batteries: a rechar geab le Lithium-Ion main batte ry pack, a rechargeable Lithium-Ion s econdary battery pack (Provi ded with some models or [...]

1 Hardware Overview 1.1 Features 1-4 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572)  Switch/Button The following switches and buttons are equipped. Satellite R20/TECRA M7 - Windows-Security button - Escape/Rotation button - Cross Function button - Wireless communication switch - Power on switch Satellite R20 - Internet b[...]

1.1 Features 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-5  Wireless LAN The computer is equipped with PCI Express Mini Card type wire less LAN card that supports 802.11 b/g or 802.11 a/b/g in the PC I Express MiniCard slot. This function can be switched on and off by a switch on the computer. ?[...]

1 Hardware Overview 1.1 Features Figure 1-1 shows the front of the computer and Figure 1-2 shows the system units configuration. Figure 1-1 Front of the computer 1-6 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572)[...]

1.1 Features 1 Hardware Overview Figure 1-2 System units configuration Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-7[...]

1 Hardware Overview 1.2 System block diagram 1.2 System block diagram Figure 1-3 shows the system block diagram. Figure 1-3 System block diagram 1-8 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572)[...]

1.2 System block diagram 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-9 The PC contains the following components.  Processor Intel ® Core TM Duo Processor (dual core) or Inte l ® Core TM Solo Processor (single core) • Core speed: Dual core: 1.60GHz (T2050)/1.66GHz (T2300E)/1.66GHz (T2300)/ 1.[...]

1 Hardware Overview 1.2 System block diagram 1-10 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572)  Memory Two memory slots capable of accep ting DDR2-SDRAM 256MB, 512MB, 1024MB or 2048MB memory modules for a maximum of 4GB. • 200-pin Small Outline DIMM • 1.8V operation • PC2-4200(DDR2-533)/PC2-5300(DDR2-667) support ?[...]

1.2 System block diagram 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-11  PCI chipset This gate array incorporates the following elem ents and functions. North Bridge (Intel 945GM (Satellite R20/TECRA M7)/945PM (TECRA M7)) - Yonah Processor System Bus Support - System Memory Interface : supports [...]

1 Hardware Overview 1.2 System block diagram 1-12 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572)  GPU controller (Internal graphic controller) • Graphics interface in North Br idge (Intel 945GM) is used. • VRAM : External DDR SDRAM MAX=128MB, Default=8MB • LCD Interface LVDS 2ch, Supports 1440×900 • Analog CRT : 36[...]

1.2 System block diagram 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-13 – Supports Magic Packet – Supports LED – Makes LAN to “Disable” in BIOS  Wireless LAN • One Mini PCI Express Card slot − Supports 802.11b/g or 802.11a/b/g − Supports Communication SW − Supports W-LAN via PC[...]

1 Hardware Overview 1.3 2.5-inch Hard Disk Drive 1.3 2.5-inch Hard Disk Drive A compact, high-capacity SATA HDD with a he ight of 9.5mm contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-4 shows a view of the 2.5-inch HDD and Tables 1-1 list the specifications. Figure 1-4 2.5-inch HDD Table 1-1 2.5-inch HDD Specifications (1/3) Specific[...]

1.3 2.5-inch Hard Disk Drive 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-15 Table 1-1 2.5-inch HDD Specifications (2/3) Items Specifications TOSHIBA HDD2D34BZK01 TOSHI BA HDD2D35BZK01 TOSHI BA HDD2D32BZK01 TOSHIBA HDD2D30BZK01 Outline Width (mm) 69.85 ± 0.25 dimensions Height (mm) 9.5 ± 0.2 Depth[...]

1 Hardware Overview 1.3 2.5-inch Hard Disk Drive 1-16 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) Table 1-1 2.5-inch HDD Specifications (3/3) Specifications Items TOSHIBA HDD2D31BZK01 FUJITSU G8BC0002WC10 Outline Width (mm) 69.85 ± 0.25 70 dimensions Height (mm) 9.5 ± 0.2 9.5 Depth (mm) 100 ± 0.41 100 Weight (g) 102 max.[...]

1.4 Optical Drive 1 Hardware Overview 1.4 Optical Drive 1.4.1 DVD-ROM Drive The DVD-ROM drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD-ROM and DVD-ROM. The DVD-ROM drive is shown in Figure 1-5. Th e dimensions and specifications of the DVD-ROM drive are described in Table 1-2, Table 1-3. Figure 1-5 DVD-ROM drive Table 1-2 DVD-RO[...]

1 Hardware Overview 1.4 Optical Drive 1-18 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) Table 1-3 DVD-ROM drive specifications Specifications Item TEAC G8CC0002E520 Data transfer speed (Read) DVD-ROM CD-ROM Max. 8x CAV Max. 24x CAV ATAPI Burst (MB/s) PIO Mode DMA Mode Ultra DMA Mode 16.7 (PIO Mode 0 to 4) 16.7 (Multi Word Mo[...]

1.4 Optical Drive 1 Hardware Overview 1.4.2 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accommodates e ither 12 cm (4.72-inch) or 8 cm (3.15- inch) CD-ROM, DVD-ROM and CD-R/RW. The DVD-ROM & CD-R/RW drive is shown in Figure 1-6. The dimensions and specifications of the DVD-ROM & CD-R/RW drive are described in Tabl e 1-4 and [...]

1 Hardware Overview 1.4 Optical Drive 1-20 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) Table 1-5 DVD-ROM & CD-R/RW drive specifications (1/2) Specifications Item MATSUSHITA G8CC0002J520 Data transfer speed (Read) DVD-ROM CD-ROM Max. 8x CAV Max. 24x CAV Data transfer speed (Write) CD-R CD-RW High Speed CD-RW Ultra Speed [...]

1.4 Optical Drive 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-21 Table 1-5 DVD-ROM & CD-R/RW drive specifications (2/2) Specifications Item TEAC G8CC00032520 Data transfer speed (Read) DVD-ROM CD-ROM Max. 8x CAV Max. 24x CAV Data transfer speed (Write) CD-R CD-RW High Speed CD-RW Ultra Speed CD[...]

1 Hardware Overview 1.4 Optical Drive 1.4.3 DVD Super Multi Drive (Double-layer) The DVD Super Multi drive accommodates eith er 12 cm (4.72-inch) or 8 cm (3.15-inch) CD/DVD-ROM, CD-R/RW, DVD±R/±RW (DL) and DVD-RAM. The DVD Super Multi drive is shown in Figure 1- 7. The dimensions and specifications of the DVD Super Multi drive are describe d in T[...]

1.4 Optical Drive 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-23 Table 1-7 DVD Super Multi drive specifications (1/2) Specifications Item MATS USHITA G8CC0002T520 Data transfer speed (Read) DVD-ROM CD-ROM Max. 8x CAV Max. 24x CAV Data transfer speed (Write) CD-R CD-RW High Speed CD-RW Ultra Speed C[...]

1 Hardware Overview 1.4 Optical Drive 1-24 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) Table 1-7 DVD Super Multi drive specifications (2/2) Specifications Item Pioneer G8CC0002U530 Data transfer speed (Read) DVD-ROM CD-ROM Max. 8x CAV Max. 24x CAV Data transfer speed (Write) CD-R CD-RW DVD-R DVD-R DL DVD-RW DVD+R DVD+R DL D[...]

1.5 Keyboard 1 Hardware Overview 1.5 Keyboard The keyboard is mounted 85(US)/87(UK) keys th at consist of character key and control key. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. Figure1-8 is a view of the keyboard. See Appendix E about a layout of the keyboard. Figure 1-8 Keyboar[...]

1 Hardware Overview 1.6 TFT Color Display 1.6 TFT Color Display The TFT color display consists of a LCD module and FL inverter board. 1.6.1 LCD Module The LCD module used for the TFT color display us es a backlight as the light source and can display images and characters of 16M colors with 1,440 × 900 (WXGA+) resolution. Figure 1-9 shows a view o[...]

1.6 TFT Color Display 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-27 1.6.2 FL Inverter Board The FL inverter board supplies a high freque ncy current to illuminate the LCD module FL. Table 1-9 lists the FL inve rter board specifications. Table 1-9 FL inverter board specifications Specifications Ite[...]

1 Hardware Overview 1.7 Power Supply 1-28 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) 1.7 Power Supply The power supply supplies different voltages to the system board. The power supply microcontroller has the following functions. 1. Judges that the DC power supply (AC ad apter) is connected to the computer. 2. Detects DC o[...]

1.7 Power Supply 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-29 Table 1-10 lists the power s upply output specifications. Table 1-10 Power supply output specifications (1/2) Power supply (Yes/No) Name Voltage [V] Power OFF (Suspend mode) Power OFF (Boot mode) No battery Object PPV 1.500 - 0.300 No [...]

1 Hardware Overview 1.7 Power Supply 1-30 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) Table 1-10 Power supply output specifications (2/2) Power supply (Yes/No) Name Voltage [V] Power OFF (Suspend mode) Power OFF (Boot mode) No battery Object SND-P5V 5 No No No AN12941A A4R7-P4V 4.7 No No No ALC262, AN12941A R3V 2.0-3.5 Yes [...]

1.8 Batteries 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-31 1.8 Batteries The PC has the following three batte ries.  Main battery  Secondary battery (Provided w ith some models or option)  Real time clock (RTC) battery Table 1-11 lists the specifica tions for these two batteries. Table 1[...]

1 Hardware Overview 1.8 Batteries 1-32 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and dete cts a full charge when the AC adapter and battery are connected to the computer. ?[...]

1.8 Batteries 1 Hardware Overview Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 1-33 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-14 lists the battery charging tim e and data preservation times. Table 1-14 RTC battery char ging/data[...]

1 Hardware Overview 1.9 AC Adapter 1-34 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) 1.9 AC Adapter The AC adapter is also used to charge the battery. Table 1-15 lists the AC adapter specifications. Table 1-15 AC adapter specifications Parameter Specification G71C00043310 (2-pin) G71C00049510 (3-pin) Power 75W (Peak 90W) Inp[...]

[CONFIDENTIAL] Chapter 2 Troubleshooting[...]

2 Troubleshooting 2-ii [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ual (960-572) 2[...]

2 Troubleshooting Satellite R20/TECRA M7 Maintena nce Man ual (960-572) [CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ..............................................................................[...]

2 Troubleshooting 2-iv [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572) 2.8 Display Troubleshooting .......................................................................................... 2-41 Procedure 1 External Monitor Check ....................................................... 2-41 Procedure 2 Diagnostic Test Program[...]

2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-v 2.16 Tablet Pen Troubleshooting ..................................................................................... 2-52 Procedure 1 Check on Windows XP Tablet PC Edition .......................... 2-52 Procedure 2 Tablet pen replacement Check .........[...]

2 Troubleshooting 2-vi [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Man ua l ( 960- 572)[...]

2.1 Troubleshooting 2 Troubleshooting 2 2.1 Troubleshooting Chapter 2 describes how to determine which Fi eld Replaceable Unit (FRU) in the computer is causing the computer to malfunction. (The “FRU ” m eans the replaceable unit in the field.) The FRUs covered are: 1. Power supply 9. Modem 2. System board 10. Bluetooth 3. 3.5” USB FDD 11. LAN[...]

2 Troubleshooting 2.2 Troubleshooting Flowchart 2-2 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Man ua l ( 960- 572) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determ ining which FRU malfunctions. Before going through the flowchart steps, check the following:  Make sure that Toshiba Windows ® XP Tablet [...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Figure 2-1 Troubleshooting flowchart (1/2) Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-3[...]

2 Troubleshooting 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (2/2) 2-4 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Man ua l ( 960- 572)[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-5 If the diagnostics program cannot detect an e rror, the problem may occur intermittently. The Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnos tic[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-6 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Man ua l ( 960- 572) 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 1 Power Suppl y Icon Check The following two icons indicate the power supply status:  Battery icon  DC IN icon The power supply controller uses the power supply status with the Battery icon and the DC IN icon as listed in the tables below. Table 2-1 Battery icon Battery icon Power s[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-8 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Man ua l ( 960- 572) When icons are blinking, perform the following procedure. 1. Remove the battery pack and the AC adap ter and cut off the power supply to the computer by force. 2. Re-attach the battery pac k and the AC adapter. If icons ar[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” On for one second “0” On for half second Interval between data bi[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-10 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2)  DC power supply (AC adapter) Error code Meaning 10h AC Adapter output voltage is over 16.5V. 11h TOSHIBA Express Port Replicator output voltage is over 16.5V. 12h Current from the DC power supply is over 7.0A. 13h Curren[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-11  E5V output Error code Meaning 50h E5V voltage is over 6.00V. 51h E5V voltage is under 4.50V when the computer is powe red on. 52h E5V voltage is under 4.50V at booting up. 54h E5V voltage is under 4.50V when EV power [...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-12 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2)  PPV output Error code Meaning 90h PPV voltage is over 1.80V. 91h PPV voltage is under 0.32V when the computer is powered on. 92h PPV voltage is under 0.32V at booting up.  PTV output Error code Meaning A0h PTV voltage[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-13  PPV output Error code Meaning D0h PPV voltage is over 1.80V. D1h PPV voltage is under 0.32V when the computer is powered on. D2h PPV voltage is under 0.32V at booting up.  PTV (Intel 945GM model) or PGV (Intel 945P[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting Procedure 3 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconn ected. Perform starting from Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the DC IN jack and wall outlet. If these cables are [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-15 Procedure 4 Quick Charge Check Check if the power supply cont roller charges the battery pack properly. Perform the following procedures: Check 1 Make sure the AC adapter is fi rmly plugged into the DC IN socket. Check 2 [...]

2 Troubleshooting 2.4 System board Troubleshooting 2-16 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) 2.4 System board Troubleshooting This section describes how to determ ine if the Sy stem board is defective. Start with Procedure 1 and continue with the other pr ocedures as instructed. The procedures described in this sect[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-17 Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the System board and initializes it.  If an error mess[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-18 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Check 3 The IRT checks the System board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) th rough (15), (20) or (21) appears, go to Procedure 4. If the [...]

2.4 System board Troubleshooting 2 Troubleshooting Procedure 2 Debug Port (D port) Check on Boot Mode Check the D port status by a debug port test. Th e tool for debug port test is shown below. Figure 2-2 A set of to ol for debug port test The test procedures are follows; 1. Connect the debug port test cable to the connector CN3400 of the system bo[...]

2 Troubleshooting 2.4 System board Troubleshooting 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting D port into FDD and input “FD starting drive:>dport”.) The D port status is displayed in the following form; 6. When the D port status is FFFFh ( normal status), go to Procedure 3. 7. When the D port statu[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-21 Table 2-4 Debug port (Boot mode) error status (1/10) D port status Inspection items Details Permission of A20 and Cl ear of software reset bit Prohibition of APIC Initialization of MCH, ICH Initialization of Super I/O Ini[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-22 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Table 2-4 Debug port (Boot mode) error status (2/10) D port status Inspection items Details Saving key scan code Setting TASK_1ms_TSC Controlling fan Enabling system spea ker Releasing mute Initializing sound items (for BEEP[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-23 Table 2-4 Debug port (Boot mode) error status (3/10) D port status Inspection items Details Initialization of MCHM Initialization of ICH7M.D30.Func0 Initialization of ICH7M.D31.Func0 Initialization of ICH7M.D31.Func1/2 In[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-24 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Table 2-4 Debug port (Boot mode) error status (4/10) D port status Inspection items Details (F103h) Resume error check S3 recovery error (I CH ) Resume error F17Ah SM-RAM checksum check Resume error F1 73h Memory configurati[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-25 Table 2-4 Debug port (Boot mode) error status (5/10) D port status Inspection items Details F106h Initialization of devices which need initialization before PCI bus initialization PIT test (at Cold boot only) and initiali[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-26 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Table 2-4 Debug port (Boot mode) error status (6/10) D port status Inspection items Details Setting operation mode of IDE device Setting operation mode of AC’97/Azalia Initialization of temperature control information KBC [...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-27 Table 2-4 Debug port (Boot mode) error status (7/10) D port status Inspection items Details (F10Ah) PCI automatic configuration Making of wo rk for a utomatic configuration Acquisition of PCI IRQ Configuration Saving of V[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-28 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Table 2-4 Debug port (Boot mode) error status (8/10) D port status Inspection items Details F11Ah INIT_DMAC (boot mode) Initialization o f DMAC F11Bh CHECK_SIO (for model s supportin g SIO) Check of SIO F11Dh Diagnostic Test[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-29 Table 2-4 Debug port (Boot mode) error status (9/10) D port status Inspection items Details Waiting for completion of initialization of Serial Port (for models supporting SIO) Waiting for completion of setting clock gene [...]

2 Troubleshooting 2.4 System board Troubleshooting 2-30 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Table 2-4 Debug port (Boot mode) error status (10/10) D port status Inspection items Details F122h Start of BIOS security check Wh en error occurred, halts at D port=F 166h F123h End of BIOS security check F124h Clear of IRT[...]

2.4 System board Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-31 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the System board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to p[...]

[CONFIDENTIAL] Chapter 3 Tests and Diagnostics[...]

3 Tests and Diagnostics 3-ii [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572)[...]

3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................................. 3[...]

3 Tests and Diagnostics 3-iv [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.21.1 Function Description .......................................................................... 3-49 3.21.2 Operations .......................................................................................... 3-49 3.22 Log Utilities .............[...]

3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-v 3.31.1 Function Description .......................................................................... 3-96 3.31.2 Accessing the SETUP Program .......................................................... 3-98 Figures Figure 3-1 Name and positions of each si[...]

3 Tests and Diagnostics 3-vi [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572)[...]

2 Troubleshooting 2.5 USB 3.5” FDD Troubleshooting 2-32 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) 2 2.5 USB 3.5” FDD Troubleshooting This section describes how to determine if the USB 3.5” FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as requ[...]

2.5 USB 3.5” FDD Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-33 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, tu rn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnos[...]

2 Troubleshooting 2.5 USB 3.5” FDD Troubleshooting Procedure 3 Connector Check The USB FDD connector may be disconnected fr om the connector on the system board or USB board. Check visually that the connector is connected firmly. Check 1 Make sure the USB FDD cable is firmly connected to the CN4610 (port 4/6), CN4612 (port 0) on the system board [...]

2.6 2.5” HDD Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-35 2.6 2.5” HDD Troubleshooting This section describes how to determine if the 2.5” HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required. Pro[...]

2 Troubleshooting 2.6 2.5” HDD Troubleshooting 2-36 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the test detects an erro r, an error message is displayed on the screen. Make sure[...]

2.6 2.5” HDD Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-37 Procedure 3 Format Check The computer’s 2.5” HDD is formatted using the DOS FORMAT program or the physical format program of the test program. To form at the 2.5” HDD, start with Check 1 below and perform the other st[...]

2 Troubleshooting 2.6 2.5” HDD Troubleshooting 2-38 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more inform [...]

2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedure 5 Connector Check an d Replacement Check The HDD is connected to the system board w ith a HDD cable. The connecting portions may be loose. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks to check the connecting por[...]

2 Troubleshooting 2.7 Keyboard Troubleshooting 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replaceme[...]

2.8 Display Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-41 2.8 Display Troubleshooting This section describes how to determ ine if th e computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Moni[...]

2 Troubleshooting 2.8 Display Troubleshooting Procedure 3 Connector and Cable Check The LCD module is connected to the System board through the LCD/FL cable. Also, the FL inverter is connected the system board through the LCD/FL cable. The cable may be firmly disconnected the board or damaged. Disassemble the com puter following the steps described[...]

2.9 Touch pad Troubleshooting 2 Troubleshooting 2.9 Touch pad Troubleshooting To determine whether the Touch pad is faulty or not, perform the following procedures: Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector and Cable Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute t[...]

2 Troubleshooting 2.10 Optical drive Troubleshooting 2.10 Optical drive Troubleshooting To check if the optical drive is defective or not, follow the troubles hooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution C[...]

2.11 Modem Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-45 2.11 Modem Troubleshooting To check if the modem is defective or malf unctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and[...]

2 Troubleshooting 2.11 Modem Troubleshooting Procedure 2 Connector Check and Replacement Check The Modem jack (RJ11) is mounted on the system board and MDC is connected to the system board. If the modem malfunctions, the connections may be bad or the MDC or system board might be faulty. Disassemble the computer following the step s described in Cha[...]

2.12 Bluetooth Troubleshooting 2 Troubleshooting Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-47 2.12 Bluetooth Troubleshooting This section describes how to determine if the Bluetooth in the computer is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as [...]

2 Troubleshooting 2.12 Bluetooth Troubleshooting Procedure 2 Connection Check The Bluetooth functional wiri ng diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the Bluetooth cable is fi[...]

2.13 LAN Troubleshooting 2 Troubleshooting 2.13 LAN Troubleshooting To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check [...]

2 Troubleshooting 2.14 Sound Troubleshooting 2.14 Sound Troubleshooting To check if the sound function is defectiv e or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execu[...]

2.15 Bridge media Slot Troubleshooting 2 Troubleshooting 2.15 Bridge media Slot Troubleshooting To check if the Bridge media slot is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows XP Tablet PC Edition Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Window s XP Tablet[...]

2 Troubleshooting 2.16 Tablet Pen Troubleshooting 2-52 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) 2.16 Tablet Pen Troubleshooting To check if the Tablet Pen is defective or not , follow the troubleshooting procedures below as instructed. CAUTION: Use the Tablet Pen supplied to this model. Procedure 1: Check on Windows XP [...]

2.16 Tablet Pen Troubleshooting 2 Troubleshooting Procedure 3 Connector Check and Replacement Check The Digitizer and LCD are connected to the system board as below. Check 1 The Digitizer may be disconnected. Make sure the Digitizer is connected to the CN9540 on the system board. If there is still an error, go to Check 2. Check 2 The Digitizer or t[...]

2 Troubleshooting 2.17 Wireless LAN Troubleshooting 2-54 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2) 2.17 Wireless LAN Troubleshooting To check if the Wireless LAN is defective or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmittin g/Receiving Check Procedure 2: Check of Antenna connect[...]

2.17 Wireless LAN Troubleshooting 2 Troubleshooting Procedure 2 Check of Antenna connection The wireless LAN functional wiri ng diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, and perform the following checks: Check 1 The wireless LAN card and the system board [...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting 2.18 Fingerprint sensor Troubleshooting CAUTION : To delete the account for confirming the fingerprint operation, it is necessary to log on by the account with the ma nagement authority. If the password has been set to log on, ask the Log-ON password to the user. To check if the Fingerprint [...]

2.18 Fingerprint sensor Troubleshooting 2 Troubleshooting Procedure 1 Setting Windows Log-ON passw ord 1. Open [User Account] from [Control Panel]. 2. Click [User Account]. 3. Click the icon of the account (user’s na me) that you want to set the password. 4. Click “Create Account”. 5. Type a password in “Type a new password”. 6. Press Tab[...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting [User's Passport] appears in “Ent er your password”. Click [Next]. When the finger print has been enrolled, [U ser’s Password] appear s. Slide your finger enrolled or type the password. Click [Next] . 4. Type the Windows logon password in “Enter your password” and click [Next][...]

2.18 Fingerprint sensor Troubleshooting 2 Troubleshooting 5. Confirm that the box of [Run interactive tu torial] is checked (when proceeding wit seeing Tutorial) and click [Next]. 6. Watch the Video carefully, click [Next]. Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONFIDENTIAL] 2-59[...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting 7. Put lightly your finger on the fingerprint sens or at the bottom right side of the display and slide your finger toward the right. Slide your finger four times. Four boxes are fi lled with fingerprints. At this time, when you click the [Replay video], you can watch the video that you have[...]

2.18 Fingerprint sensor Troubleshooting 2 Troubleshooting When you have failed in any time of four tim es reading and want to practice again, click [Try again]. When you have fully su cceeded in four times of reading, the message of “ Fully succeeded” appears. 8. Click [Next]. The displa y of [User’s Fingers] 9. Click the box you want to enro[...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting Put lightly the first joint of your finger you wa nt to enroll on the fi ngerprint sensor and slide your finger toward you. Enroll your finge r three times. Every time your finger has been successfully enrolled, one box is checke d. When your finger has been successfully enrolled three times[...]

2.18 Fingerprint sensor Troubleshooting 2 Troubleshooting 13. Type a backup password two times in the fo llowing display. (This password is different from the password of Windows logon.) 14. Click [Next]. The [Finish] display appears. 15. Click [Finish], “Welcom e” display appears. Satellite R20/TECRA M7 Mainte na nce Man ua l ( 960- 572) [CONF[...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting Procedure 3 Authentication of fingerprint 1. Turn on the computer to start up Windows. 2. In the Windows logon window, put lightly the first joint of your finger registered and slide your finger toward the right. When authenticated, [Success] is displayed in the fingerprint authentication di[...]

2.18 Fingerprint sensor Troubleshooting 2 Troubleshooting Procedure 4 Connector Check and Replacement Check The Fingerprint sensor cable is connected to the connector CN9560 on th e Fingerprint sensor board and connector CN9540 on the system board. Check 1 Check the Fingerprint sensor cable is firmly connected to the connector CN 9560 on the Finger[...]

2 Troubleshooting 2.18 Fingerprint sensor Troubleshooting 2-66 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintena nce Manual (960-57 2)[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. There are Service Pr[...]

3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572)  REAL TIMER TEST  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST Other tests are:  Wireless LAN TEST (Wireless LAN test disk)  LAN/Modem/Bluetooth/IEEE1394 TEST (L AN/Modem/Bluetooth/IEEE1394 test disk)  Sound T[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-3 3.1.2 H/W (Hardware) initial information setting tool The H/W initial inform ation setting tool consists of the following programs.  Initial configuration  DMI information save  DMI information recovery  System configur[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the USB floppy disk drive. 2. Turn on the computer with pressing the U . Then, the following menu ap[...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2.1 Diagnostics menu (T&D) To execute this program, press 1 , or select 1-Repair Main (T&D) in the startup menu and press Enter . The following menu appears. TOSHIBA personal computer Common DIAGNOSTICS Version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Functions 1 through 12 are the Diagnostic Tests. Function 88 sets the floppy disk drive and hard disk drive error retry count (0-255). To exit the submenu of the Diagnostic Test and returns to the Diagnostics Menu, set the highlight bar to function 99 and press Enter . Select the option you [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-7 Use the up and down arrow keys to move the cursor to “ ERROR STOP ”. Use the right and left arrow keys to move the cursor to the desired option and press Enter . Selecting YES of ERROR STOP stops the test program when[...]

3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-8 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.3 Setting of the hardware configuration To execute this program, press 2 or select 2-Repair initial config set in the startup menu and press Enter and follow the directions on the screen. The H/W initial informa[...]

3.3 Setting of the hardware configuration 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-9 Setting of the HWSC Setting of the UUID Display of the DMI information (including UUID) Setting of DVD region code (Yes/No) After completion of the above settings, H/W configuration & DMI information are appea[...]

3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-10 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest 04 System configuration display This subtest displays the information of the system configuration. Confirm the contents and press Enter . For more details on the system configuration inform ation, refer t[...]

3.4 Heatrun Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-11 3.4 Heatrun Test To execute this program, press 3 or select 3-Repair heatrun (T&D) in the startup menu and press Enter . After selecting the test, the same subtests as 3.23 RUNNING TEST are executed successively. For more details on [...]

3 Tests and Diagnostics 3.5 Subtest Names 3-12 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quic[...]

3.5 Subtest Names 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-13 Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER [It is not supported] 01 02 03 Ripple pattern Function Wraparound 7 ASYNC [It is not supported] 01 02 03 FIR/SIR point to point (send) FIR/SIR point to point[...]

3 Tests and Diagnostics 3.6 System Test 3-14 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.6 System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ROM checksum Th[...]

3.6 System Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-15 This subtest checks the status for the quick charge. Subtest 05 DMI read This subtest displays the information in the Flash-ROM in the following format. *** DMI Data Display Ver X.XX *** Model Name : XXXXXXXXXXX Version Number : XXXXXXXXX[...]

3 Tests and Diagnostics 3.7 Memory Test 3-16 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional m[...]

3.8 Keyboard Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-17 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed [...]

3 Tests and Diagnostics 3.9 Display Test 3.9 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAh and 55h) to the [...]

3.9 Display Test 3 Tests and Diagnostics Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mode 117 1024*768 64K] [Mode 118 1024*768 16M] The dis[...]

3 Tests and Diagnostics 3.9 Display Test 3-20 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest 06 “H” pattern display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH[...]

3.10 Floppy Disk Test 3 Tests and Diagnostics 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD. The contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Enter and [...]

3 Tests and Diagnostics 3.10 Floppy Disk Test 3-22 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX XXX DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : k[...]

3.11 Printer Test 3 Tests and Diagnostics 3.11 Printer Test CAUTION : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wrapar[...]

3 Tests and Diagnostics 3.11 Printer Test Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE : To execute thi[...]

3.12 Async Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-25 3.12 Async Test CAUTION : Async Test is not supported for this model. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest [...]

3 Tests and Diagnostics 3.13 Hard Disk Test 3-26 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : 1. When executing subtest02, 03, 04, 06, 08 and 09, the message [The hard disk[...]

3.13 Hard Disk Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-27 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest. Hard DISK TEST XXXXX[...]

3 Tests and Diagnostics 3.13 Hard Disk Test 3-28 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder. (Test the data interference in the neighbor track) [...]

3.14 Real Timer Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-29 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 0[...]

3 Tests and Diagnostics 3.14 Real Timer Test 3-30 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments. Make sure the date and time are displayed in the following form at: Current[...]

3.15 NDP Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-31 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP test This test checks the following functions of NDP:  Control word  Status word  [...]

3 Tests and Diagnostics 3.16 Expansion Test 3-32 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound CAUTION : PCMCIA wraparound test is not supported for this [...]

3.16 Expansion Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-33 Subtest 02 RGB monitor ID NOTE: To execute this subtest, an external monitor with monitor ID function is required. Connect the external monitor to the PC for the test of ID acquisition. The judgment of acquisition is based on the pane[...]

3 Tests and Diagnostics 3.17 CD-ROM/DVD-ROM Test 3-34 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.17 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TD[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-35 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name Comm[...]

3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-36 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD -[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-37 Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DM[...]

3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status 3-38 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an[...]

3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-39 Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1”[...]

3 Tests and Diagnostics 3.20 Only One Test 3-40 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.20 Only One Test 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. ################[...]

3.20 Only One Test 3 Tests and Diagnostics Subtest 01 Pressed Key Display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function which causes the key’s [...]

3 Tests and Diagnostics 3.20 Only One Test Subtest 02 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Touch Pad direction and parameter. B) Touch Pad switch function check. This test displays the response from the touch pad and touch pad switch. When moving your finger on the touch pad towards the upper left, the <[...]

3.20 Only One Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-43 Subtest 03 Wireless Communication Switch This subtest checks if the Wireless comm unication switch works properly. If the test is started with the switch ON, the following message appears in the display. Wireless communication switch i[...]

3 Tests and Diagnostics 3.20 Only One Test 3-44 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) NG message appears in the display if an error is found during the test. Confirm the connection of cable, and then execute the test again. Press 9 and Enter to return to Only One Test menu. Subtest 05 LED This subtest checks if each LED[...]

3.20 Only One Test 3 Tests and Diagnostics Subtest 06 Button This subtest checks if the buttons in the following figure work properly. Windows Security Button ESC/Rotation Button Cross Function Button TOSHIBA Assist button TOSHIBA Presentation button The following message appears in the display. “Press Function Button key” Press Cross Function [...]

3 Tests and Diagnostics 3.20 Only One Test Subtest 07 Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2. Prevent the machine from shake or shock. Set the machine against the verti[...]

3.20 Only One Test 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-47 When this subtest is selected, the following message appears in the display. The revision data has written in Exit to [Enter] / Continue to [Space] key Then press Space to continue the test. The following message appears in the display[...]

3 Tests and Diagnostics 3.20 Only One Test 3-48 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) ** Setting OK! ** Press [Enter] key When a defective is found during the each check above, the following message appears in the display. The test is halted at the point when the defective is found. ** Setting ERROR! ** Press [Enter] ke[...]

3.21 Head Cleaning 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-49 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selecting t[...]

3 Tests and Diagnostics 3.22 Log Utilities 3-50 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk, or output the data to a printer or [...]

3.22 Log Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED 001 FDD 01 0000 180 00001 00 00 0000 FDD-TIME OUT ER[...]

3 Tests and Diagnostics 3.23 Running Test 3-52 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 06) 3. Display test (subtest 01) 4. Real timer test (subtes[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-53 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a f[...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-54 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program [...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-55 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage similar to the on[...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-56 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display [...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-57 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No)[...]

3 Tests and Diagnostics 3.25 System Configuration 3-58 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3 3.25 System Configuration 3.25.1 Function Description The System Configuration program contains th e following configuration information for the computer: 1. Processor Type [Code/L2 cache] 2. Chip set [VRAM] 3. BIOS ROM versio[...]

3.25 System Configuration 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-59 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMH[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel-made b/g) 3-60 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.26 Wireless LAN Test Program (Intel-made b/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11b/g). To execute the wireless LAN test, use th[...]

3.26 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-61 When a defective is detected in the test, following typical cause is considered. • • • • • • Connection of wireless LAN card Using a wrong wireless LAN card (Using unspecified card) Defective wi[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel-made b/g) 3-62 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest03 Antenna check & communication test of 11b mode CAUTION: 1. To execute subtest 03-05, use another computer (with Calexico wireless LAN card) that can communicate by the wireless LAN as a respon[...]

3.26 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-63 Subtest04 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. After finishing the test, OK message will appear in the display. Press any ke[...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g) 3-64 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.27 Wireless LAN Test Program (Intel-made a/b/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11a/b/g). To execute the wireless LAN test, [...]

3.27 Wireless LAN Test Program (Intel-made a/b/g) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-65 If a defective is found during the test, NG message will appear in the display. Press any key and following message will appear in the display. ************************************************************[...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g) 3-66 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) When a defective is detected in the test, following typical cause is considered. • • • Connection of wireless LAN card Defective wireless LAN card Disappearance of MAC address data Checking the conn[...]

3.27 Wireless LAN Test Program (Intel-made a/b/g) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-67 When a defective is detected in the test, following typical cause is considered. • • • • • • • • Connection of wireless LAN card Connection of wireless LAN antenna cable (Main/Aux) Conditi[...]

3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g) 3-68 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest05 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. For more details on procedure and contents of this subtest, refer to Subtes[...]

3.28 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-69 3.28 Wireless LAN Test Program (Atheros) This section describes how to perform the wireless LAN transm itting-receiving test with the test program. NOTE: Use another computer (with Atheros 11a/g(MB44ag)/Atheros 11[...]

3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Atheros) 3-70 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.28.1 Setting the responder machine 1. MB44ag is installed 1) Boot the computer by MB4x Responder media. 2) The Responder T&D is automatically started. 2. MB6x is installed As the capacity of MB6x T&D is [...]

3.28 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-71 6) When the file copy is completed, the following test m enu is displayed. Press r . The Responder T&D is started. ************************************************************ * * * Atheros MB6x DUT mode Maint[...]

3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Atheros) 3-72 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 5) When the file copy is completed, the following test m enu is displayed. Press d . The Responder T&D is started. ************************************************************ * * * Atheros MB6x DUT mode Maint[...]

3.28 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-73 When an error (read error of EEPROM date) has detected, the following is displayed. ------------ERROR------------ file bac.txt cannot be opened 2. MAC Address Check The MAC address of the installed Wireless LAN ca[...]

3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Atheros) 3-74 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) When an error has detected, the following is displayed. ************************************** * * * 11a Communication Test : NG !! * * * * Please refer to log.txt * * * ************************************** 4. C[...]

3.28 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-75 6. SKU & MAC Check 11a/b/g communication test All the test is executed in the order of SKU check of Module, MAC Address Check, Communication test of 11a m ode, Communica tion test of 11b m ode and Communicatio[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetoot h/IEEE1394 Test Program 3-76 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/Bluetooth/IEEE13[...]

3.29 LAN/Modem/Bluetoot h/IEEE1394 Test Program 3 Tests and Diagnostics Subtest01 (i82562 + ICHx) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error count = 00000 LOOPBACK TEST 100Mbps Auto-negotiation TxRx Te[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetoot h/IEEE1394 Test Program Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear: Testing adapter...hit <ESC> to abort. * External Loopback Test...PASSED Testing completed. * * Loop[...]

3.29 LAN/Modem/Bluetoot h/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-79 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Denki Seisakusyo)” for t[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-80 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.29.3 Bluetooth test To execute this test, input 3 and press Enter . NOTE : Use another computer that can comm unicate by the Bluetooth as a reference machine to perform this test. Insert a floppy disk cont[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-81 Subtest01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: -----------------[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-82 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) If the target machine has any problem, it displays Error CODE. The following message is displayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D fo[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-83 If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-6 Error code for Bluetooth test (BD_ADDR) (1/2) Er[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-84 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Table 3-6 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision.[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-85 When the Bluetooth test menu is displayed, press T to select the test and press Enter in the test machine. The following m essage will appear: ----------------------------------------------------------------[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-86 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) If the target machine has any problem, the following m essage “ INCOMPLETE ” is displayed with the Error Code. ----------------------------------------------------------------------------- Bluetooth Subs[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-87 If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-7 Error code for Bluetooth test (BD_ADDR of the DU[...]

3 Tests and Diagnostics 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-88 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction[...]

3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-89 3.29.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. The following men[...]

3.30 Sound Test program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-90 3 Tests and Dia tics 3.30 Sound Test program gnos This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Insert the test program disk for Sound test in the floppy disk [...]

3.30 Sound Test program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-91 To return to the Sound test menu, Press 9 and Enter . Then following message will appear in the display. *********************************** ******** May I Restart ? ******* *********************************** Press any key to con[...]

3 Tests and Diagnostics 3.30 Sound Test program 3-92 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest02 Sine Wave This subtest is executed by loading the COM file (ADSIN.COM). The program expands sine wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to p[...]

3.30 Sound Test program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-93 3.30.3 CD Sound (Standard) To execute the CD Sound (Standard) test, press 3 and Enter . Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). Following m[...]

3 Tests and Diagnostics 3.30 Sound Test program 3-94 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Subtest02 English Narration Selected this subtest, narration in English starts. For more details on the procedure, refer to the subtest01. Subtest03 Test Tone A CAUTION: Before starting subtest03, be sure to set the sound at prope[...]

3.30 Sound Test program 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-95 (2) Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR C[...]

3 Tests and Diagnostics 3.31 SETUP 3-96 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 3.31 SETUP 3.31.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory 2. System Date/Time 3. Battery (a) Battery Save Mode (b) PCI Express Link ASPM (c) Enhanced C-States 4. Password 5. H[...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-97 11. Security Controller (a) TPM (b) Clear TPM Owner 12. Display (a) Power On Display (b) LCD Display Stretch (c) TV Type 13. Peripheral 14. LEGACY EMULATION (a) USB KB/Mouse Legacy Emulation (b) USB-FDD Legacy Emulation (c) USB Memory BIOS Sup[...]

3 Tests and Diagnostics 3.31 SETUP 3.31.2 Accessing the SETUP Program Turn on the power while pressing ESC, the following menu appears. Check system. Then press [F1] key. Then press F1 . The following display appears. * 3 *4 * 4 *4 *4 NOTE: *1: Follow the HWSC about display / non-display of HDD Password window. *2: This appears in models for TCL (C[...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-99 Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pages. 2. Press eith[...]

3 Tests and Diagnostics 3.31 SETUP SETUP Options The SETUP screen is divided into 15 functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. This field displays the total amount of mem ory installed and is automatically calculated by the computer. You cannot [...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-101 NOTE: Display of the LCD Brightness will be changed in the condition below: (*1) Operating the battery (*2) Using the AC adapter User Setting Use this option to set the battery save parameters on the sub-window, BATTERY SAVE OPTIONS . Battery[...]

3 Tests and Diagnostics 3.31 SETUP 3-102 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) Cooling Method Maximum Performance If the CPU becomes too hot, the fan turns on automatically in a high speed to cool down the CPU. Performance If the CPU becomes too hot, the fan turns on automatically. When the CPU tem perature falls to a n[...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-103 4. Password This option sets or resets the user password for power on. Registered The user password has been registered. Not registered The user password has not been registered. For details on setting the user password, refer to the User’s[...]

3 Tests and Diagnostics 3.31 SETUP 3-104 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 6. Boot Priority (a) Boot Priority This option sets the priority for booting the computer. Select from the following settings. FDD → HDD → CD-ROM → LAN: The com puter looks for bootable files in the following order: FDD, HDD, CD- ROM an[...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-105 7. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Core-Multi Processing NOTE: This is not displayed in PCs with a single core CPU. The Core Mul[...]

3 Tests and Diagnostics 3.31 SETUP (d) Virtualization Technology Virtualization Technology sets enable or disable of the Intel Virtualization Technology installed in the CPU. Intel Virtualization Technology is the technique that allows one machine to operate as multiple virtual machines. Enabled Enables Virtualization Technology. Disabled Disables [...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-107 NOTE: 1. Do not remove the AC adapter and battery pack at the same time when you use this feature. If you do so, data saved by the resume function will be lost. You must also reset this option. 2. If you have set a password and the computer b[...]

3 Tests and Diagnostics 3.31 SETUP 3-108 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) This option displays the address and interrupt level for hard disk drive and optical disk drive. It is for information only and cannot be changed. Built-in HDD This item cannot be changed. CD-ROM This item cannot be changed. 10. PCI Bus This [...]

3.31 SETUP 3 Tests and Diagnostics Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 3-109 12. Display This group of options configures the computer’s display. (a) Power On Display This option is used to select the display when booting up. Auto-Selected Selects an external monitor if one is connected. Otherwise it selects the int[...]

3 Tests and Diagnostics 3.31 SETUP 3-110 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual (960-572) 13. Peripheral Use this option to select the peripheral’s mode. (a) Internal Pointing Device This option enables or disables the touch pad Enabled Enables the touch pad. (Default) Disabled Disables the touch pad. 14. LEGACY EMULATION (a) US[...]

[CONFIDENTIAL] Chapter 4 Replacement Procedures[...]

4 Replacement Procedures 4-ii [CONFIDENTIAL] Satellite R2 0/TECRA M7 Mainte nance Manual (960-572) 4[...]

4 Replacement Procedures Satellite R20/ TECRA M7 Maintenance Manual (960-5 72) [CONFIDENTIAL] 4-iii Chapter 4 Contents 4.1 Overview ................................................................................................................... 4-1 Safety Precautions ...............................................................................[...]

4 Replacement Procedures 4-iv [CONFIDENTIAL] Satellite R20/TECRA M7 Mainte nance Manual (960-572) 4.21 GPU heat sink ......................................................................................................... 4-50 4.22 Fan/Heat sink/CPU ................................................................................................. 4[...]

4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-v Figures Figure 4-1 Removing the battery pack................................................................................. 4-8 Figure 4-2 Removing the reserve pen ................................................................................ 4-10[...]

4 Replacement Procedures 4-vi [CONFIDENTIAL] Satellite R2 0/TECRA M7 Mainte nance Manual (960-572) Figure 4-32 Removing the system board ........................................................................... 4-48 Figure 4-33 Removing the GPU heat sink ......................................................................... 4-50 Figure 4-34 Re[...]

4.1 Overview 4 Replacement Procedures 4 Replacement Procedures 4.1 Overview This chapter describes the procedure for rem oving and replacing the fi eld replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particul[...]

4 Replacement Procedures 4.1 Overview 4-2 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Manual ( 960-572) Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1) Always use the genuine battery that is authorized by Toshiba o[...]

4.1 Overview 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-3 Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2. B[...]

4 Replacement Procedures 4.1 Overview Disassembly Procedure Four main types of cable connector are used. Pressure plate connector • • • • Spring connector Back flip connector Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cab le out [...]

4.1 Overview 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-5 Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the computer. • [...]

4 Replacement Procedures 4.1 Overview Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage. NOTE : To tighten screws quickly and accu rately, an electric screwdriver is [...]

4.1 Overview 4 Replacement Procedures Grip Color Some screws have a colored grip area to he lp you determine the leng th of the screw.  Even numbered length screws: Brown  Odd numbered length screws: White  Special length screw: Blue “Special length screw” means screws whose lengt h is indic ated in an integral number to th e first dec[...]

4 Replacement Procedures 4.2 Battery pack 4.2 Battery pack Removing the battery pack The following describes the procedure for removing the battery pack. (See Figure 4-1.) CAUTION: Take care not to short circuit the term inals when removing the battery pack. Similarly, do not drop, knock, scra tch, disassemble, twist, or bend the battery pack. 1. T[...]

4.2 Battery pack 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-9 Installing the battery pack The following describes the procedure for inst alling the battery pack. (See Figure 4-1.) CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, operated, handled, or dispos[...]

4 Replacement Procedures 4.3 Reserve pen 4.3 Reserve pen Removing the reserve pen The following describes the procedure for re m oving the reserve pen. (See Figure 4-2.) 1. Remove the reserve pen from the pen holder. Reserv e pen Figure 4-2 Removing the reserve pen Installing the reserve pen The following describes the procedure for in stalling the[...]

4.4 Tablet PC pen 4 Replacement Procedures 4.4 Tablet PC pen Removing the tablet PC pen The following describes the procedure for rem o ving the tablet PC pen. (See Figure 4-3.) 1. Gently push the tablet PC pen . The pen will then protrude slightly from the side. 2. Remove the tablet PC pen from the tablet PC pen slot. Tablet PC pen Figure 4-3 Remo[...]

4 Replacement Procedures 4.5 PC card/Bridge media 4.5 PC card/Bridge media 4.5.1 PC card Removing the PC card The following describes the procedure for rem oving the PC card. (See Figure 4-4.) CAUTION: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manuals of this computer. 1. Turn the computer upside [...]

4.5 PC card/Bridge media 4 Replacement Procedures 4.5.2 Bridge media Removing the Bridge media The following describes the procedure for re m oving the Bridge media. (See Figure 4-5.) CAUTION: Insert or remove the Bridge media in accordance with any instructions in the Bridge media manual or the manuals of this computer. 1. Push the Bridge media . [...]

4 Replacement Procedures 4.6 MDC/USIM card 4.6 MDC/USIM card Removing the MDC/USIM card The following describes the procedure for re m oving the MDC/USIM card. (See Figure 4-6 and 4-7.) 1. Loosen the screw (with e-ring) and remove the MDC/USIM card cover . 2. Remove the following screws securing the USIM card and MDC. • M2 × 8B BIND screw × 2 ([...]

4.6 MDC/USIM card 4 Replacement Procedures 5. Remove the MDC from the connector CN3010 on the system board. 6. Disconnect the MDC cable from the connector on the MDC. MDC MDC cable CN3010 Figure 4-7 Removing the MDC Installing the MDC/USIM card The following describes the procedure for inst alling the MDC/USIM card. (See Figure 4-6 and 4-7.) 1. Con[...]

4 Replacement Procedures 4.7 HDD 4.7 HDD Removing the HDD The following describes the procedure for re moving the HDD. (See Figure 4-8 to 4-10.) CAUTION: Take care not to press on the top or bottom of the HDD. Pressure may cause data loss or damage to the device. 1. Turn the computer upside down. 2. Remove the following screws and HDD slot cover . [...]

4.7 HDD 4 Replacement Procedures 3. Hold the tab to raise the HDD assembly and pull out the HDD assembly from the connector of the HDD cable . NOTE: When removing the HDD assembly, be care ful not to tear the tab. If the tab is torn, replace the HDD holder with a new one. HDD cable HDD assembly Tab Figure 4-9 Removing the HDD assembly Satellite R20[...]

4 Replacement Procedures 4.7 HDD 4. Place the HDD assembly on a flat surface and rem ove the following screws fixing the HDD holder. • M3 × 4S FLAT HEAD screw × 4 5. Separate the HDD holder and HDD . M3x4S FLAT HEAD M3x4S FLAT HEAD HDD holder (HDD frame and tab) HDD M3x4S FLAT HEAD Figure 4-10 Removing the HDD 4-18 [CONFIDENTIAL ] Satellite R20[...]

4.7 HDD 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-19 Installing the HDD The following describes the procedure for in stalling the HDD. (See Figure 4-8 to 4-10.) CAUTION: Do not hold the HDD by its top and bottom face. It may damage the HDD. 1. Seat the HDD in the HDD holder and secure them with[...]

4 Replacement Procedures 4.8 Keyboard 4.8 Keyboard Removing the keyboard The following describes the procedure for remo ving the keyboard. (See Figure 4-11 to 4-12.) 1. Turn the computer face up and open the display. 2. Insert your fingers into the slots on both sides and remove the keyboard holder A . 3. Remove the following screws securing the ke[...]

4.8 Keyboard 4 Replacement Procedures 6. Remove the following screw and keyboard support plate . • M2.5 × 8B FLAT HEAD screw × 1 7. Disconnect the keyboard cable from the connector CN3200 on the system board and remove the keyboard . M2.5x8B FLAT HEAD CN3200 Keyboard cable Keyboard Keyboard support plate Figure 4-12 Removing the keyboard Satell[...]

4 Replacement Procedures 4.8 Keyboard 4-22 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Manual ( 960-572) Installing the keyboard The following describes the procedure for inst alling the keyboard. (See Figure 4-11 to 4-12.) 1. Place the keyboard face down on the palm rest. 2. Connect the keyboard cable to the connector CN3200 on the system b[...]

4.9 Memory module 4 Replacement Procedures 4.9 Memory module CAUTION: The power must be turned off wh en you remove the memory module. Removing the memory module with the power on risks damaging the module or the computer itself. Do not touch the memory module termi nals. Any dirt on the terminals may cause memory access problems. Never press hard [...]

4 Replacement Procedures 4.9 Memory module 2. Open the left and right latches outside and remove the memory module(s) . Memory module Latch Latch Slot B Slot A Figure 4-14 Removing the memory module 4-24 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Manual ( 960-572)[...]

4.9 Memory module 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-25 Installing the memory module To install the memory module(s), make sure th e com puter is in boot mode and powered off. Then perform the following procedure. (See Figure 4-13 and 4-14.) 1. Insert the memory module(s) into the connec[...]

4 Replacement Procedures 4.10 SW membrane 4.10 SW membrane Removing the SW membrane To remove the SW m embrane, perform th e following procedure. (See Figure 4-15.) 1. Remove the SW membrane cover while releasing latches. 2. Disconnect the SW membrane cable from the connector CN9600 on the system board. 3. Slide the SW membrane in the direction of [...]

4.10 SW membrane 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-27 Installing the SW membrane To install the SW membrane , perform the following procedure. (See Figure 4-15.) 1. Install the SW membrane to the slot while sliding it in the opposite direction at removing. 2. Connect the SW membrane cab[...]

4 Replacement Procedures 4.11 Optical disk drive 4.11 Optical disk drive Removing the optical disk drive The following describes the procedure for rem ovi ng the optical disk drive. (See Figure 4-16 and 4-17.) 1. Remove the following screw . • M2.5 × 8B FLAT HEAD screw × 1 2. Turn over the computer and remove the following screw . • M2.5 × 6[...]

4.11 Optical disk drive 4 Replacement Procedures 4. Remove the following screws and pushing plate from the optical drive assem bly. • S t u d s c r e w × 2 5. Remove the following screw and mounting plate from the optical drive assemb ly. • M2 × 3S S-THIN HEAD screw × 1 Stud screw M2 × 3S S-THIN HEAD Pushing plate Mounting plate Figure 4-17[...]

4 Replacement Procedures 4.11 Optical disk drive 4-30 [CONFIDENTIAL ] Satellite R20/TECRA M7 Maintenance Manual ( 960-572) Installing the opt ical disk drive The following describes the procedure for installi ng the optical drive. (See Figure 4-16 and 4- 17.) 1. Install the mounting plate to the optical disk drive a ssem bly and secure it with the [...]

4.12 Cover assembly and Base assembly 4 Replacement Procedures 4.12 Cover assembly and Base assembly Removing the cover assembly and base assembly The following describes the procedure for removing the cover assembly and base assembly. (See Figure 4-18 to 4-20.) 1. Turn the display 90 degrees clockwise and remove the hinge rear cover . 2. Remove th[...]

4 Replacement Procedures 4.12 Cover assembly and Base assembly 4. Turn the display 90 degrees counter clockwise. 5. Close the display and turn over the computer. 6. Remove the following screws . • M2.5 × 16B FLAT HEAD screw × 3 (“16” in the figure below) • M2.5 × 6B FLAT HEAD screw × 9 (“6” in the figure below) 16 16 16 6 6 6 6 6 6 [...]

4.12 Cover assembly and Base assembly 4 Replacement Procedures 7. Separate the base assembly and cover assembly . Base assembly Cover assembly Figure 4-20 Removing the cover assembly and base assembly (3) Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-33[...]

4 Replacement Procedures 4.12 Cover assembly and Base assembly Installing the Cover assem bly and Base assembly The following describes the procedure for instal ling the cover assem bly and base assembly. (See Figure 4-18 to 4-20.) 1. Install the base assemb ly to the cover assembly . 2. Secure the cover assembly with the f ollowing screws . • M2[...]

4.13 Base latch 4 Replacement Procedures 4.13 Base latch Removing the base latch The following describes the procedure for rem oving the base latch. (See Figure 4-21.) 1. Remove the base latch while releasing the lat ches of the back. Base latch Latch Figure 4-21 Removing the base latch Installing the base latch The following describes the procedur[...]

4 Replacement Procedures 4.14 Touch pen case/Ba ttery lock 4.14 Touch pen case/Battery lock Removing the Touch pen case/Battery lock The following describes the procedure for re m oving the touch pen case/battery lock. (See Figure 4-22.) 1. Remove the touch pen case while releasing the latches . 2. Remove the battery lock . Battery lock Touch pen c[...]

4.15 Bluetooth module 4 Replacement Procedures 4 Replacement Procedures 4.15 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below. (See Figure 4-23.) CAUTION: Do not try to remove the Bluetooth module with the computer turned on. You can damage the computer or Bluetooth module. Do not touch the conne[...]

4 Replacement Procedures 4.15 Bluetooth module 4-38 [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Installing the Bluetooth module To install the Bluetooth module, follow the steps below. (See Figure 4-23.) 1. Connect the Bluetooth cable to the connector on the Bluetooth module. 2. Connect the Bluetooth cable to the connecto[...]

4.16 Wireless LAN card 4 Replacement Procedures 4.16 Wireless LAN card Removing the Wireless LAN card To remove the Wireless LAN card, follow the steps below. (See Figure 4-24.) CAUTION: Do not try to remove the wireless LAN card with the computer turned on. The computer or the wireless LAN card can be damaged. Do not touch the connectors on the wi[...]

4 Replacement Procedures 4.16 Wireless LAN card 4-40 [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Installing the Wireless LAN card To install the Wireless LAN card, f ollow the steps below. (See Figure 4-24.) CAUTION: Be sure to switch the computer off before installing the wireless LAN card. Otherwise, the computer or the[...]

4.17 Microphone/Front panel 4 Replacement Procedures 4.17 Microphone/Front panel Removing the Microphone/Front panel The following describes the procedure for remo ving the microphone/front panel. (See Figure 4-25 and 4-26.) 1. Disconnect the microphone cable from the connector CN6050 on the system board. 2. Lift the system board a little and remov[...]

4 Replacement Procedures 4.17 Microphone/Front panel 3. Remove the microphone cable from the guides of the front panel. 4. Remove the microphone hold plate and microphone from the front panel. Microphone Microphone cable Microphone hold plate Guide Figure 4-26 Removing the microphone Installing the Microphone/Front panel The following describes the[...]

4.18 Modem jack/USB board/DC-IN jack 4 Replacement Procedures 4.18 Modem jack/USB board/DC-IN jack Removing the Modem jack/USB board/DC-IN jack The following describes the procedure for removing the modem jack/USB board/DC-IN jack. (See Figure 4-27 to 4-29.) 1. Peel off the glass tape and insulator and remove the modem jack from the slot. Glass tap[...]

4 Replacement Procedures 4.18 Modem jack/USB board/DC-IN jack 2. Disconnect the USB board cable from the connector CN4620 on the system board. 3. Remove the USB board from the slot. 4. Disconnect the USB board cable from the connector CN4631 on the USB board. CN4620 USB board cable USB board CN4631 Figure 4-28 Removing the USB board 4-44 [CONFIDENT[...]

4.18 Modem jack/USB board/DC-IN jack 4 Replacement Procedures 5. Disconnect the DC-IN jack cable from the connector CN8800 on the system board. 6. Remove the DC-IN jack from the slot DC-IN jack cable DC-IN jack CN8800 Figure 4-29 Removing the DC-IN jack Installing the Modem j ack/USB board/DC-IN jack The following describes the procedure for inst a[...]

4 Replacement Procedures 4.19 RTC battery 4.19 RTC battery Removing the RTC battery The following describes the procedure for rem o ving the RTC battery. (See Figure 4-30 and 4-31.) 1. Disconnect the RTC battery cable from the connector CN9300 on the system board. 2. Remove the following screw and RTC battery holder . • M2.5 × 6B FLAT HEAD screw[...]

4.19 RTC battery 4 Replacement Procedures 3. Open the insulator and remove the RTC battery from the RTC battery holder. Insulator RTC battery Figure 4-31 Removing the RTC battery Installing the system board/RTC battery The following describes the procedure for instal ling the RTC battery. (See Figure 4-30 and 4- 31.) 1. Install the RTC battery to t[...]

4 Replacement Procedures 4.20 System board 4.20 System board Removing the System board The following describes the procedure for re moving the system board. (See Figure 4-32.) 1. Disconnect the sensor cable , digitizer cable , LCD cable and touch pad cable from the connector CN9500 , CN9540 , CN5000 and CN3201 on the system board. 2. Peel off the g[...]

4.20 System board 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-49 Installing the system board The following describes the procedure for inst alling the system board. (See Figure 4-32.) 1. Install the system board to the cover assembly and secure it w ith the f ollowing screw . • M2.5 × 6B FLAT [...]

4 Replacement Procedures 4.21 GPU heat sink 4.21 GPU heat sink Removing the GPU heat sink The following describes the procedure for re moving the GPU heat sink. (See Figure 4-33.) 1. Peel of the insulator . 2. Remove the following screws and GPU heat sink . • M2 × 4B BIND screw × 2 M2x4B BIND GPU heat sink Insulator Figure 4-33 Removing the GPU[...]

4.21 GPU heat sink 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-51 Installing the GPU heat sink The following describes the procedure for inst alling the GPU heat si nk. (See Figure 4-33.) 1. If there is already silicon grease on the GPU and GPU heat sink, clean it with a cloth. Using a special ap[...]

4 Replacement Procedures 4.22 Fan/Heat sink/CPU 4.22 Fan/Heat sink/CPU Removing the Fan/Heat sink/CPU The following describes the procedure for rem o ving the fan/heat sink/CPU. (See Figure 4-34 to 4-36.) 1. Peel off the glass tape and disconnect the f an cable from the connector CN8771 on the system board. 2. Remove the following screws securing t[...]

4.22 Fan/Heat sink/CPU 4 Replacement Procedures 4. Remove the following screws and separate the fan and heat sink . • M2.5 × 4B FLAT HEAD screw × 2 Heat sink Fan M2.5x4B FLAT HEAD Figure 4-35 separating the fan and heat sink 5. Unlock the CPU by turning the cam counterclockwise on the CPU socket by 90 degrees with a flat-b lade screwdriver. Fig[...]

4 Replacement Procedures 4.22 Fan/Heat sink/CPU 6. Remove the CPU from the CPU socket. CAUTION: When removing the CPU, lift it up right above. Otherwise, pins of CPU may be damaged. Installing the Fan/Heat sink/CPU The following describes the procedure for inst alling the fan/heat sink/CPU. (See Figure 4-34 to 4-38.) 1. Make sure the cam is in the [...]

4.22 Fan/Heat sink/CPU 4 Replacement Procedures 4. Apply new grease on the CPU using a special syringe as shown in the following figure. Apply quarter of scale (0.25ml) of grease evenly on the CPU chip. When silicon grease is already app lied to the CPU, wipe them o ff with a cloth in advance. Figure 4-38 Applying new grease 5. Install the fa n to [...]

4 Replacement Procedures 4.23 Sensor board 4.23 Sensor board Removing the Sensor board The following describes the procedure for removing the sensor board. (See Figure 4-39.) 1. Remove the sensor board from the slot. 2. Disconnect the sensor cable from the connector CN9510 on the sensor board. Sensor board Sensor cable CN9510 Figure 4-39 Removing t[...]

4.24 Speaker 4 Replacement Procedures 4.24 Speaker Removing the speaker The following describes the procedure for removing the speaker. (See Figure 4-40.) 1. Peel off the insulators and acetate tapes . 2. Remove the speaker covers while releasing latches. 3. Remove the speakers from the slots. Speaker cover Acetate tape Insulator Speaker Insulator [...]

4 Replacement Procedures 4.24 Speaker 4-58 [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Installing the speaker The following describes the procedure for installing the speaker. (See Figure 4-40.) 1. Install the sp eakers to the slots on both sides. 2. Install the sp eaker covers to the slots on both sides while hooking the[...]

4.25 Touch pad 4 Replacement Procedures 4.25 Touch pad Removing the Touch pad The following describes the procedure for re m oving the touch pad. (See Figure 4-41 and 4- 42.) 1. Remove the following screw . • M2.5 × 6B FLAT HEAD screw × 1 2. Remove the touch pad cover while releasing four latches . Touch pad cover M2.5 × 6B FLAT HEAD Latch Fig[...]

4 Replacement Procedures 4.25 Touch pad 3. Remove the touch pad from the slot. 4. Disconnect the touch pad cable from the connector on the touch pad. Touch pad cable Touch p ad Figure 4-42 Removing the touch pad Installing the Touch pad The following describes the procedure for inst alling the touch pad. (See Figure 4-41 to 4-42.) 1. Connect the to[...]

4.26 LCD mask 4 Replacement Procedures 4.26 LCD mask Removing the LCD mask The following describes the procedure for rem oving the LCD mask. (See Figure 4-43.) 1. Peel off the mask seals (9 points) from the LCD mask and remove the following screws securing the LCD m ask. • M2.5 × 6B FLAT HEAD screw × 9 2. Remove the LCD mask while releasing lat[...]

4 Replacement Procedures 4.26 LCD mask CAUTION : When removing the LCD mask, be sure to keep the following steps (order) referring to the figure below. 1. Release the latches o n the top from the right to the left. 2. Release the latches on the ri ght side from the top to the bottom. 3. Release the latches on the bottom from the right toward the le[...]

4.26 LCD mask 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-63 Installing the LCD mask The following describes the procedure for installing the LCD m ask. (See Figure 4-43.) 1. Install the LCD mask to the display cover while securing the latche s. NOTE: When installing the LCD mask, wipe the LCD wi[...]

4 Replacement Procedures 4.26 LCD mask CAUTION : When installing the LCD mask, be sure to keep the following steps (order) referring to the figure below. 1. Engage the latches on the left side while fiting the LCD mask to the correct position. 2. Engage the latches on the top from the left to the right. 3. Engage the latches on the ri ght side from[...]

4.27 Fingerprint sensor board 4 Replacement Procedures 4.27 Fingerprint sensor board Removing the Fingerprint sensor board The following describes the procedure for rem oving the fingerprint sensor board. (See Figure 4-44.) 1. Remove the following screw and fingerprint sensor board . • M2.5 × 6B FLAT HEAD screw × 1 2. Disconnect the fingerprint[...]

4 Replacement Procedures 4.28 Switch board 4.28 Switch board Removing the Switch board The following describes the procedure for rem o ving the switch board. (See Figure 4-45.) 1. Remove the following screw securing the switch board and pull up the sw itch board . • M2.5 × 6B FLAT HEAD screw × 1 2. Disconnect the switch cable from the connector[...]

4.29 LCD unit/FL inverter 4 Replacement Procedures 4.29 LCD unit/FL inverter Removing the LCD unit/FL inverter The following describes the procedu re for removing the LCD unit/FL inverte r. (See Figure 4- 46 to 4-48.) NOTE: When replacing the LCD unit, do not give the hinge portion a strong press. It may cause the breakage of the hinge assembly. Al[...]

4 Replacement Procedures 4.29 LCD unit/FL inverter 3. Remove the following screw securing the LCD unit. • M2.5 × 6B FLAT HEAD screw × 1 4. Carefully lift up the top of the LCD unit . NOTE: When lifting up the top of the LCD unit, hold the corners of the LCD unit. The top edge of LCD unit is sensitive area. 5. Peeling off two glass tapes and dis[...]

4.29 LCD unit/FL inverter 4 Replacement Procedures 7. Remove the following screws and two LCD supports from the LCD. • M2 × 3S S-THIN HEAD screw × 4 M2 × 3S S-THIN HEAD LCD LCD support M2 × 3S S-THIN HEAD Figure 4-48 Removing the LCD support NOTE: 1) Be careful not to apply pressure to the ICs along the edge of LCD unit. The ICs are easily da[...]

4 Replacement Procedures 4.29 LCD unit/FL inverter 4-70 [CONFIDENTIAL ] Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) Installing the LCD unit/FL inverter The following describes the procedu re for installing the LCD unit/FL inverter. (See Figure 4- 46 to 4-48.) 1. Set two LCD supports to the LCD and secure them with the following screw s .[...]

4.30 Digitizer 4 Replacement Procedures 4.30 Digitizer CAUTION : Read following instructions be fore handling the Digitizer. Do not carry the LCD module by holding the FL cable in one’s hand because it may result to cut the FL cable, and cause displa y function failure or lighting failure. Be careful to handle the bezel guide. There is a portion [...]

4 Replacement Procedures 4.30 Digitizer Do not make any scratches on the B/L and TAB by the edge of the digitizer when installing the digitizer because it may result to brea k the TAB or make scratches on the B/L and cause display function failure. Do not pull up the PCB hardly wh en installing the digitizer b ecause it may result to give stress on[...]

4.30 Digitizer 4 Replacement Procedures Do not turn up the digitizer because it may re sult to give stress on the TAB or PCB and cause the display function failure. Do not put any instrument on the LCD modul e because it may result to make scratch on the cell, polarization sheet or B/L and brea k the TAB and may cause the display function failure. [...]

4 Replacement Procedures 4.30 Digitizer Do not hold, press and rub the TAB because it may result to break the TAB and cause the display function failure. Make sure to put the LCD m odule on the flat place. If th e LCD module is put on the uneven place, it may result to break the T AB, make scratch on the B/L or polarization sheet and cause the disp[...]

4.30 Digitizer 4 Replacement Procedures Satellite R20/ TECRA M7 Maintena nce Manual ( 960-572) [CONFIDENTIAL] 4-75[...]

4 Replacement Procedures 4.30 Digitizer Removing the Digitizer The following describes the procedure for removing the digitizer. (See Figure 4-49.) 1. Remove the following screws securing the digitizer. • M2 × 3S S-THIN HEAD screw × 3 2. Remove the digitizer from the LCD unit. Digitizer M2x3S S-THIN HEAD M2x3S S-THIN HEAD Figure 4-49 Removing t[...]

4.30 Digitizer 4 Replacement Procedures Installing the digitizer The following describes the procedure for installing the digitizer. (See Figure 4-49.) 1. Slide the digit ize r into the back pocket of the LCD. CAUTION : When replacing the digitizer, fit the di gitizer into the back of the LCD toward the arrow pointing. 2. Secure the digitizer with [...]

4 Replacement Procedures 4.31 LCD latch assembly 4.31 LCD latch assembly Removing the LCD latch assembly The following describes the procedure for removing the LCD latch assembly. (See Figure 4- 50.) 1. Remove the LCD latch assembly from the slot as shown in the following figure. LCD latch assembly Figure 4-50 Removing the LCD latch assembly Instal[...]

4.32 Hinge assembly 4 Replacement Procedures 4.32 Hinge assembly Removing the Hinge assembly The following describes the procedure for rem o ving the hinge assembly. (See Figure 4-51 to 4-53.) 1. Peel off the insulator and acetate tape to release the wireless LAN antenna cable and Bluetooth antenna cable. Insulator A cetate tape Figure 4-51 Removin[...]

4 Replacement Procedures 4.32 Hinge assembly 2. Remove the following screws . • M3 × 4S FLAT HEAD screw × 2 3. Turn the display rear cover 90 degrees clockwise and remove the display rear cover from the cover assembly. M3 × 4S FLAT HEAD Display rear cover Figure 4-52 Removing th e hinge assembly (2) 4-80 [CONFIDENTIAL ] Satellite R20/ TECRA M7[...]

4.32 Hinge assembly 4 Replacement Procedures 4. Remove the following screws and hinge assembly by lifting it up. • M2.5 × 6S S-THIN HEAD screw × 2 M2.5 × 6S S-THIN HEAD Hinge assembly Figure 4-53 Removing th e hinge assembly (3) Installing the Hinge assembly The following describes the procedure for instal ling the hinge assem bly. (See Figure[...]

4 Replacement Procedure 4.33 Fluorescent lamp 4-82 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual ( 960-572) 4 4.33 Fluorescent lamp This system uses LCD modules from the following suppliers. The procedure for replacing the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. Type Part No. Supplier Sectio[...]

4.33 Fluorescent lamp 4 Replacement Procedure 4.33.1 Replacing the 14.1 Inch CHIMEI Fluorescent lamp The following describes the procedure for replacing the fluorescent lamp (See Figure 4-54 to 4-59). Disassembling Fluorescent lamp 1. Tear off the AL tape (1) and PCBA protector film (2). Figure 4-54 Replacing 14.1 Inch CHIMEI fluorescent lamp (1) S[...]

4 Replacement Procedure 4.33 Fluorescent lamp 2. Tear off the CU tape (1) and unscrew the metal frame fixed screws (2). Figure 4-55 Replacing 14.1 Inch CHIMEI fluorescent lamp (2) 4-84 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual ( 960-572)[...]

4.33 Fluorescent lamp 4 Replacement Procedure 3. To remove the metal fram e hooks out of the backlight unit (1), first remove the hooks of the bottom side, left side and right side and then remove the m etal frame (2). CAUTION : Be sure to take the frame off parallely in case of any deformation. Figure 4-56 Replacing 14.1 Inch CHIMEI fluorescent la[...]

4 Replacement Procedure 4.33 Fluorescent lamp 4. Take of the X-PCB oppositely. CAUTION : Be careful upon taking off the PCB in case of any twisting deformation to TCP. Panel unit B/L unit Figure 4-57 Replacing 14.1 Inch CHIMEI fluorescent lamp (4) 4-86 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual ( 960-572)[...]

4.33 Fluorescent lamp 4 Replacement Procedure 5. Tear off the film tape (1) from the protector sheet. 6. Tear off the protector sheet (2), prism (3), LGP (4), LGP tape (5) and reflector (6) from the backlight unit in turn. CAUTION: Be careful upon taking off each sheet in case any damage. Housing Lamp ASS’Y Figure 4-58 Replacing 14.1 Inch CHIMEI [...]

4 Replacement Procedure 4.33 Fluorescent lamp 7. Unscrew the lamp ASS’Y fixed screws (1). Housing Lamp ASS’Y Figure 4-59 Replacing 14.1 Inch CHIMEI fluorescent lamp (6) 4-88 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual ( 960-572)[...]

4.33 Fluorescent lamp 4 Replacement Procedure Satellite R20/TECRA M7 Maintenance Manual (960-572) [CONFIDENTIAL] 4-89 Assembling Fluorescent lamp Assembling is the opposite order of the disassembling.[...]

4 Replacement Procedure 4.33 Fluorescent lamp 4-90 [CONFIDENTIAL] Satellite R20/TECRA M7 Maintenance Manual ( 960-572)[...]

[CONFIDENTIAL] Appendices[...]

Appendices App-ii [CONFIDENTIAL] SatelliteR20/T ECRAM7 Mainte nance Manual (960-572)[...]

Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] App-iii Appendix Contents Appendix A Handling the LCD Module ......................................................................... A-1 Appendix B Board Layout ................................................................................................B-1 B.1 Sys[...]

Appendices App-iv [CONFIDENTIAL ] SatelliteR20/TECRAM7 Ma intenance Ma nual (960-572) C.16 CN4400 Bluetooth connector (20-pin) ...................................................... C-17 C.17 CN4610 USB connector (Port 6/ ４ ) (8-pin) .............................................. C-18 C.18 CN4612 USB connector (Port 0) (6-pin) ...................[...]

Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] App-v SW board (FCYSW*) C.40 CN9550 System board I/F connector (15-pin)........................................... C-29 Appendix D Keyboard Scan/Character Codes .............................................................. D-1 Appendix E Key Layout ....................[...]

Appendices App-vi [CONFIDENTIAL ] SatelliteR20/TECRAM7 Ma intenance Ma nual (960-572) Figures Figure B-1 System board layout (front) ...........................................................................B-1 Figure B-2 System board layout (back) ...........................................................................B-3 Figure B-3 Fingerprin[...]

Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] App-vii Table C-5 PC card I/F connector (70-pin) ..................................................................... C-8 Table C-6 Bridge Media I/ F connector (42-pin) .......................................................... C-10 Table C-7 Docking I/F connector (140[...]

Appendices App-viii [CONFID ENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572) Panel switch board (FCYPR*) Table C-36 System board I/ F connector (3-pin) ............................................................ C-26 SIM board (FCYSM*) Table C-37 System board I/ F connector (10-pin) .....................................................[...]

Appendix A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it i[...]

Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with co tton or a soft cloth. If it is still dirty, try breathing on the surface to create a light cond ensate and wipe it again. If the surface is very dirty, we recomme nd a LCD cleaning agent. Apply the agent to a cloth and then wipe the panel’s surfa[...]

Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellit[...]

Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly c[...]

Appendix A Handling the LCD Module Appendices 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can damage the panel’s polarization. SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] A-5[...]

Appendices Appendix A Handling the LCD Module A-6 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72)[...]

Appendix B Board Layout Appendices Appendix B Appendix B Board Layout B.1 System Board Front View Figure B-1 System board layout (front) SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] B-1[...]

Appendices Appendix B Board Layout B-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) Table B-1 System board ICs and connectors (front) Number Part’s name IS2101 Bridge media connecto r CN1400 Memory connecto r (A) CN1410 Memory connecto r (B) CN9600 Switch board I/F connector CN3200 Keyboard connector CN3400 Debug port I/F con[...]

Appendix B Board Layout Appendices B.2 System Board Back View Figure B-2 System board layout (back) SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] B-3[...]

Appendices Appendix B Board Layout B-4 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) Table B-2 System board ICs and connectors (back) Number Name CN5501 S-Video connector CN8800 DC-IN ja ck CN4620 USB board I/F conne ctor CN2610 3G connector CN1820 Optical drive connector CN9520 SIM board I/F connector CN3201 Touch pad bo ard I/[...]

Appendix B Board Layout Appendices B.3 Fingerprint Sensor Board Front and Back View <Front layout> <Back layout> Figure B-3 Fingerprint sensor board layout Table B-3 Fingerprint sensor board connector Number Name CN9560 System boa rd I/F connector SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] B-5[...]

Appendices Appendix B Board Layout B.4 Panel Switch Board Front and Back View <Front layout> <Back layout> Figure B-4 Panel switch board layout Table B-4 Panel switch board connector Number Name CN9510 System board I/F connector B-6 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72)[...]

Appendix B Board Layout Appendices B.5 SIM Board Front and Back View <Front layout> <Back layout> Figure B-5 SIM board layout Table B-5 SIM board connector Number Name CN9530 System board I/F connector SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] B-7[...]

Appendices Appendix B Board Layout B.6 Switch Board Front and Back View <Front layout> <Back layout> Figure B-6 Switch board layout Table B-6 Switch board connector Number Name CN9550 System board I/F connector B-8 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72)[...]

Appendix B Board Layout Appendices B.7 Touch Pad Board Front and Back View <Front layout> <Back layout> Figure B-7 Touch pad board layout Table B-7 Touch pad board connectors Number Name CN3250 System board I/F connector CN3251 Touch pad I/F connector SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] B-9[...]

Appendices Appendix B Board Layout B.8 USB Board Front and Back View <Front layout> <Back layout> Figure B-8 USB board layout Table B-8 USB board connectors Number Name CN4631 System board I/F connector CN4630 USB port 7 B-10 [CO NFIDENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572)[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] C-1 Appendix. C Pin Assignment Appendix C Pin Assignment System board (FAPNS*) C.1 CN1410 Memor y B connector (200-pin) Table C-1 Memory B connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRVREF-B0V I 2 GND - 3 GND -[...]

Appendices Appendix. C Pin Assignment C-2 [CONFIDENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572) Table C-1 Memory B connector (200-pin)(2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 57 BDQ22-B1P I/O 58 BDQ19-B1P I/O 59 GND - 60 GND - 61 BDQ29-B1P I/O 62 BDQ25-B1P I/O 63 BDQ28-B1P I/O 64 BDQ24-B1P I/O 65 GND - 66 GND - 67 BDM3-B1[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] C-3 Table C-1 Memory B connector (200-pin) (3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 129 BDQS4-B1N I/O 130 BDM4-B1P I 131 BDQS4-B1P I/O 132 GND - 133 GND - 134 BDQ38-B1P I/O 135 BDQ34-B1P I/O 136 BDQ39-B1P I/O 137 BDQ35-B1P I/O 138[...]

Appendices Appendix. C Pin Assignment C-4 [CONFIDENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572) C.2 CN1400 Memor y A connector (200-pin) Table C-2 Memory A connector (200-pin) (1/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 MRVREF-BOV I 2 GND - 3 GND - 4 ADQ04-B1P I/O 5 ADQ07-B1P I/O 6 ADQ06-B1P I/O 7 ADQ00-B1P I/O 8 GND - 9 G[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] C-5 Table C-2 Memory A connector (200-pin)(2/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 69 N.C. - 70 ADQS3-B1P I/O 71 GND - 72 GND - 73 ADQ30-B1P I/O 74 ADQ27-B1P I/O 75 ADQ26-B1P I/O 76 ADQ31-B1P I/O 77 GND - 78 GND - 79 MCKE0-B1P I 8[...]

Appendices Appendix. C Pin Assignment C-6 [CONFIDENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572) Table C-2 Memory A connector (200-pin )(3/3) Pin No. Signal Name I/O Pin No. Signal Name I/O 141 ADQ40-B1P I/O 142 ADQ41-B1P I/O 143 ADQ45-B1P I/O 144 GND - 145 GND - 146 ADQS5-B1N I/O 147 AMD5-B1P I 148 ADQS5-B1P I/O 149 GND - 150 GND - 15[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] C-7 C.3 CN1820 ODD I/ F connect or (50-pin) Table C-3 ODD I/F connector (50-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 NC - 2 NC - 3 NC - 4 NC - 5 (IDRSTB-P3N) O 6 PDD08-P3P I/O 7 CDD07-P3P I/O 8 PDD09-P3P I/O 9 PD06-P3P I/O 10[...]

Appendices Appendix. C Pin Assignment C-8 [CONFIDENTIAL] SatelliteR20/T ECRAM7 Maintena nce Manual ( 960-572) C.4 CN1850 SATA I/F connector (10-pin) Table C-4 SATA I/F connector (10-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 ZSATT0-P1P O 2 ZSATT0-P1N O 3 GND - 4 ZSATR0-P1N I 5 ZSATR0-P1P I 6 GND - 7 P3V - 8 GND - 9 P5V - 10 GND - 1T[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [CONFIDENTIAL ] C-9 Table C-5 PC card I/F connector (70-pin) (2/2) Pin No. Signal Name I/O P i n N o . Signal Name I/O 35 GND - 36 ACCD1-P3N I/O 37 ACAD02-PYP I/O 38 ACAD04-PYP I/O 39 ACAD06-PYP I/O 40 ACD14-PYP I/O 41 ACAD08-PYP I/O 42 ACAD10-PYP I/O 43 ACVS[...]

Appendices Appendix. C Pin Assignment C-10 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.6 IS2101 Bridge Media I/F connector (42-pin) Table C-6 Bridge Media I/F connector (42-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 MSDAT2-P3P I/O 2 MSDAT3-P3P I/O 3 MSBS-P3P I/O 4 GND - 5 GND - 6 FM-P3V I 7 MSCLK-P3P I/O 8 MS[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-11 C.7 CN2300 Docking I/F connector (140-pin) Table C-7 Docking I/F c onnector (140-pin) (1/2) Pin No. Signal Name I/O Pin No. Signal Name I/O A1 GND - A2 GND - A3 DSKDC - A4 PVBAT2 - 1 DCOUT - 2 DCOUT - 3 DOCDT1-S3 N I 4 GND - 5 BT2VD - 6 BT[...]

Appendices Appendix. C Pin Assignment C-12 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) Table C-7 Docking I/F connector (140-pin) (2/2) Pin No. Signal Name I/O Pin No. Signal Name I/O 65 VOID - 66 VOID - 67 ZBIDDP-EXP I/O 68 ZBIDON-EXN I/O 69 ZBIDCN-EXP I/O 70 ZBIDCP-EXP 71 DCOUT - 72 DCOUT - 73 PWRSW-S3N I 74 DDCON-P5P O 75 NC[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-13 C.8 CN2600 PCI-Express mini card (WLAN) I/F connector (52-pin) Table C-8 PCI-Express mini card (WLAN) I/F connector (52-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 PEWAKE-E3N O 2 P3V - 3 WCHDAT-P3P O 4 GND - 5 WCHCLK-P3P O 6[...]

Appendices Appendix. C Pin Assignment C-14 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.9 CN2610 PCI-Express mini car d (3G) I/F connector (52-pin) Table C-9 PCI-Express mini card (3G) I/F connector (52-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 PEWAKE-E3N O 2 P3V - 3 NC - 4 GND - 5 NC - 6 1R5-P1V - 7 NC - 8 U[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-15 C.10 CN3010 MDC I/F connector (12-pin) Table C-10 MDC I/F connector (12-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 GND - 2 NC - 3 ACZOT1-P3P I/O 4 NC - 5 GND - 6 E3V - 7 ACZSY1-P3P O 8 GND - 9 ACZIN1-E3P I/O 10 GND - 11 ACZ[...]

Appendices Appendix. C Pin Assignment C-16 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.12 CN3201 PAD connector (8-pin) Table C-12 PAD connector (8-pin) Pin No. Signal Name I/O P i n N o . Signal Name I/O 1 GND - 2 GND - 3 IPDCLK-P5P I/O 4 IPDCLK-P5P I/O 5 IPDDAT-P5P I/O 6 IPDDAT-P5P I/O 7 P5V - 8 P5V - C.13 CN3400 Debugging [...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-17 C.15 CN4200 IEEE1394 connector (4-pin) Table C-15 IEEE1394 connector (4-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 ZTPB0-P3N I/O 2 ZTPB0-P3P I/O 3 ZTPA0-P3N I/O 4 ZTPA0-P3P I/O 1T GND - 2T GND - 3T GND - 4T GND - C.16 CN4400 Bl[...]

Appendices Appendix. C Pin Assignment C-18 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.17 CN4610 USB connecto r (Port 6/4) (8-pin) Table C-17 USB connector (Port 6/4) (8-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 USB0PS-E3V - 2 ZUSBP6-E3N I/O 3 ZUSBP6-E3P I/O 4 GND - 5 USB0PS-E3V - 6 ZUSBP4-E3N I/O 7 ZUSBP4-E3P I[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-19 C.20 CN5000 LCD connector (40-pin) Table C-20 LCD connector (40-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 BRT2DA-S3P O 2 BRT1-P5P O 3 BRT0-P5P O 4 FL-P5V - 5 FL-P5V - 6 FL-P5V - 7 NC - 8 GND - 9 GND - 10 GND - 11 P3V - 12 PNL-[...]

Appendices Appendix. C Pin Assignment C-20 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.22 CN5501 S-Video connector (4-pin) Table C-22 S-Video connector (4-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 AGND - 2 AGND - 3 LUMINA-PYP O 4 CHROMA-PYP O 1T GND - 2T GND - 3T GND - 4T GND - C.23 CN6050 Internal microphone co[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-21 C.26 J6310 Headphone connector (6-pin) Table C-26 Headphone connector (6-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 (A-GND) - 2 HEADL-PXP O 3 HEADR-PXP O 4 DETECTA-P4N I 5 A-GND - 6 N.C. - C.27 CN8800 DC-IN connector (4-pin) Ta[...]

Appendices Appendix. C Pin Assignment C-22 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.30 CN8771 Fan connector (4-pin) Table C-30 Fan connector (4-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 P5V - 2 FANG-P3P I 3 GND - 4 (FPWM-S3P) O C.31 CN9500 PR board I/F connector (3-pin) Table C-31 PR board I/F connector (3-pi[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-23 C.33 CN9540 Digitizer switch I/F connector (41-pin) Table C-33 Digitizer switch I/F con nector (41-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 22 GND - 2 GND - 23 GND - 3 GND - 24 GND - 4 E3V - 25 GPBTNA-S3N I 5 FGSPON-S3N[...]

Appendices Appendix. C Pin Assignment C-24 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) C.34 CN9600 SW board I/F connector (13-pin) Table C-34 SW board I/F connector (13-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 8 CDSTOP-S3N O 2 NC - 9 CDNEXT-S3N O 3 NC - 10 CDPREV-S3N O 4 GPBTNC-S3N I 11 NC - 5 GPBTND-S3N I [...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-25 Fingerprint sensor board (FCYFS*) C.35 CN9560 System board I/F connector (6-pin) Table C-35 System board I/F connector (6-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 Power E3V - 2 FGSPON-S3N I 3 GND - 4 ZUSBFS-E3N I/O 5 ZUSBFS-E[...]

Appendices Appendix. C Pin Assignment C-26 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) Panel switch board (FCYPR*) C.36 CN9510 System board I/F connector (3-pin) Table C-36 System board I/F connector (3-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PNLOFF-S3N O 2 TPLOFF-S3V O 3 GND -[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-27 SIM board (FCYSM*) C.37 CN9530 System board I/F connector (10-pin) Table C-37 System board I/F connector (10-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 UIMPWR-P3V O 2 NC - 3 UIMRST-P3V O 4 UIMCLK-P3P O 5 UIMDAT-P3P I/O 6 NC - 7[...]

Appendices Appendix. C Pin Assignment C-28 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72) USB board (FCYUS*) C.38 CN4631 System board I/F connector (8-pin) Table C-38 System board I/F connector (8-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 USB2PS-E5V - 2 USB2PS-E5V - 3 ZUSBP5-E3N I/O 4 ZUSBP5-E3P I/O 5 GND - 6 GND - 7[...]

Appendix. C Pin Assignment Appendices SatelliteR20/T ECRAM7 Mainte nance Manual (960-572) [CONFIDENTIAL ] C-29 SW board (FCYSW*) C.40 CN9550 System board I/F connector (15-pin) Table C-40 System board I/F connector (15-pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 GND - 2 GPBTNA-S3N O 3 GPBTNB-S3N O 4 PWRSW-S3N O 5 GND - 6 KBRT00-S3N O 7 K[...]

Appendices Appendix. C Pin Assignment C-30 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72)[...]

Appendix D Keyboard Scan/Character Codes Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [ CONFIDENTIAL] D-1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E[...]

Appendices Appendix D Keyboard Scan/Character Codes D-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 ¦ 2B AB 5D F0 5D *2 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 2[...]

Appendix D Keyboard Scan/Character Codes Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [ CONFIDENTIAL] D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75[...]

Appendices Appendix D Keyboard Scan/Character Codes D-4 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc Refer to table 2-25 126 Pause Refer to table 2-25 202 Fn[...]

Appendix D Keyboard Scan/Character Codes Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [ CONFIDENTIAL] D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL [...]

Appendices Appendix D Keyboard Scan/Character Codes D-6 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 [...]

Appendix D Keyboard Scan/Character Codes Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [ CONFIDENTIAL] D-7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D [...]

Appendices Appendix D Keyboard Scan/Character Codes D-8 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix. E Key Layout Appendices Appendix. E K ey Layout Appendix E Key Layout Figure E-1 Key layout (UK) Figure E-2 Key layout (US) SatelliteR20/T ECRAM7 Mainte nance Manual ( 960-572) [ CONFIDENTIAL] E-1[...]

Appendices Appendix. E Key Layout E-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-5 72)[...]

Appendix F W iring Diagrams Appendices Appendix F Appendix F Wiring Diagrams F .1 RGB Monitor Wrap around connector Figure F-1 RGB Monitor W raparound connector F .2 LAN Loopback Connector Figure F-2 LAN loopback Connector SatelliteR20/TECRAM7 Maintenance Manual (960-572) [CONFIDENTIAL] F-1[...]

Appendices Appendix F W iring Diagrams F-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572)[...]

Appendix G BIOS Rewrite Pr ocedures Appendices Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite th e system BIOS program when you update the system BIOS. Tools T o rewrite the BIOS, you need the following tool:  BIOS rewriting disk for the computer that has renewed BIOS data. Rewriting the BIOS Note: 1. Connect the AC ada[...]

Appendices Appendix G BIOS Rewrite Pr ocedur es G-2 [ CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572)[...]

Appendix H EC/KBC Rewrite Pr ocedures Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [ CONFIDENTIAL] H-1 Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite th e EC/KBC system program when you update the EC/KBC system. Tools T o rewrite the EC/KBC, you need the following tool:  EC/KBC rewriting dis[...]

Appendices Appendix H EC/KBC Rewrite Pr ocedures H-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572)[...]

Appendix I Reliability Appendices SatelliteR20/TECRAM7 Maintenance Manual (960-572) [CONFIDENTIAL] I-1 Appendix I Appendix I Reliability The following table shows MTBF (Mean T ime between Failures). Table I-1 MTBF MTBF Time (hours) System (Satellite R20) 5943.86 System (TECRA M7 Intel 945GM model) 5931.18 System (TECRA M7 Intel 945PM model) 5864.65[...]

Appendices Appendix I Reliability I-2 [CONFIDENTIAL] SatelliteR20/TECRAM7 Maintenance Manual (960-572)[...]