Toshiba PQF46X инструкция обслуживания

Qosmio F40/F45 Maintena nce Manual Toshiba Personal Computer Qosmio F40/F45 (PQF43x) (PQF44x) (PQF46x) (PQF47x) Maintenance Manual TOSHIBA CORPORATION S/ No[...]

ii Qosmio F40/F45 M aintenance Manual Copyright © 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Toshiba Qosmio F40/F45 Maintenance M[...]

Qosmio F40/F45 Maint enance Manual iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Qosmio F40/F45, referred to as Qosm io F40/F45 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) a[...]

iv Qosmio F40/F45 M aintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Qosmio F40/F45 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for ma[...]

Qosmio F40/F45 Maint enance Manual v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are use[...]

Chapter 1 Hardware Overview[...]

1 Hardware Overview 1.1 Features Qosmio F40/F45 Maintena nce Manual 2[...]

1.1 Features 1 Hardware Overview Chapter 1 Contents 1.1 Features ................................................................................................................... ...... 5 1.2 System Unit Components ........................................................................................... 14 1.3 2.5-inch HDD .....................[...]

1 Hardware Overview 1.1 Features Figures Figure 1-1A ID Parts Description Placement Part A ........................................................... 10 Figure 1-1B ID Parts Description Placement Part B ........................................................... 11 Figure 1-2 Computer Block Diagram .................................................[...]

1.1 Features 1 Hardware Overview 1.1 Features The Toshiba Qosmio F40/F45 a full size note book PC based on the Core2 Duo Processor and Celeron M Processor, providing high-speed pr ocessing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time. The display use[...]

1 Hardware Overview 1.1 Features y 1024 MB (64M × 8 × 16P)/667 MHZ y 2048 MB (64Mx16x16P)/667 MHZ  Hard Disk Drive (HDD) The computer accomm odates 9.5 mm and 12.5 mm two kinds of height HDD types with following storage capacities: y 60 GB (9.5 mm thick) SATA (5,400rpm ) y 80 GB (9.5 mm thick) SATA (5,400rpm ) y 100 GB (9.5 mm thick) SATA (5,4[...]

1.1 Features 1 Hardware Overview  Battery The computer has a removable 6 Cell Lithium Ion battery pack and an internal RTC battery (rechargeable).  Universal Serial Bus (USB) Ports The computer has four USB 2.0 ports. It is supported to daisy-chain a maxim um of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbp[...]

1 Hardware Overview 1.1 Features  Express Card Slot (BTO) The ICH8M provides PCI Express root ports which are compliant to the PCI Express Base Specification, Revision 1.0a. The root port supports 2.5 Gb/s bandwidth in each direction (5 Gb/s concurrent) and two vi rtual channels for full isochronous data support.  Multiple Digital Media Card [...]

1.1 Features 1 Hardware Overview The internal Mini Card slot suppor ts IEEE802.11g (MOW) / IEEE802.11ag (MOW) / IEEE802.11ag (ROW) / IEEE802.11ag (JPN) / IEEE802.11agn (MOW) / IEEE802.11agn (ROW) / IEEE802.11agn (JPN) car d. The Antenna has three wires dual band antenna support for BTO.  Internal Modem (BTO) The computer contains a MDC, enabling[...]

1 Hardware Overview 1.1 Features  Figures 1-1A/1-1B/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively. Figure 1-1A ID Parts Description Placement Part A Qosmio F40/F45 Maint enance Manual 10[...]

1.1 Features 1 Hardware Overview Figure 1-2B ID Parts Description Placement Part B Qosmio F40/F45 Maint enance Manual 11[...]

1 Hardware Overview 1.1 Features Figure 1-3 Computer Block Diagram Qosmio F40/F45 Maint enance Manual 12[...]

1.1 Features 1 Hardware Overview Figure 1-4 System Board Configurations Qosmio F40/F45 Maint enance Manual 13[...]

1 Hardware Overview 1.2 System Unit Components Qosmio F40/F45 Maint enance Manual 14 1.2 System Unit Components Figure 1-4 is Block Diagram of the System Unit[...]

1.2 System Unit Components 1 Hardware Overview Figure 1-5 System Unit Block Diagram Qosmio F40/F45 Maint enance Manual 15[...]

1 Hardware Overview 1.2 System Unit Components Qosmio F40/F45 Maint enance Manual 16 The system unit of the computer consists of the following com ponents:  Processor: Core2 Duo Processor and Celeron M Processor. y Core2 Duo Processor (800MHz) − Core speed: 1.80/2.00/2.20/2.40 GHz − System bus: 800 MHz − On-die level 2 cache: 2 MB (1.8 GHz[...]

1.2 System Unit Components 1 Hardware Overview − 39.03Kb used for nVidia G86 − 24.01Kb used for PXE ROM − 35.65Kb used for SMI − 37.86Kb used for PNP Code − 11.55Kb used for BIOS Code − 21.04Kb used for USB − 16.17Kb used for Setup − 9.31Kb used for AHCI − 3.82Kb used for Display Engine − 1.09Kb used for Decode Code − 0.52Kb u[...]

1 Hardware Overview 1.2 System Unit Components Qosmio F40/F45 Maint enance Manual 18 − LAN Controller − RTC − GPIO − Enhanced Power Management − Manageability − System Management Bus (SMBus 2.0) − Intel High Definition Audio Controller − Integrated FAN Speed Control  Graphics Controller Intel GM965/GL960 integrated graphics or PM[...]

1.2 System Unit Components 1 Hardware Overview y Two independent 16/20/24-bit S/PDIF-Out converters support 44.1 k/48 k/96 k/192 kHz sample rate. y One 16/20/24-bit S/PDIF-In converter supports 44.1 k/48 k/96 k/192 kHz sample rate. y High quality analog differential CD input. y Support external PCBEEP input and built-in digital BEEP generator. y Tw[...]

1 Hardware Overview 1.2 System Unit Components Qosmio F40/F45 Maint enance Manual 20  Modem Controller Built-in MDC card with Askey. Functions of modem controller: y Digital signal conductor protection y Ring wake-up support y Azalia interface y Communication codes supported: − For data communication: V.90 (China)/V.92, data rates: 28kbps/56kb[...]

1.2 System Unit Components 1 Hardware Overview − IEEE802.11agn: 2.4GHz / 5.4GHz Qosmio F40/F45 Maint enance Manual 21[...]

1 Hardware Overview 1.3 2.5-inch HDD 1.3 2.5-inch HDD The computer contains an extremely low-pr ofile and lightweight, high-perform ance HDD. The HDD incorporates 9.5 mm / 12.5 m m height magnetic disk and mini-W inchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 60, 80, 100, 120, 160, 200, 250[...]

1.4 DVD Super Multi (+-R Double Layer)) 1 Hardware Overview Qosmio F40/F45 Maint enance Manual 23 1.4 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-in ch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 4x spee d, U[...]

1 Hardware Overview 1.5 HD DVD-ROM Qosmio F40/F45 Maint enance Manual 24[...]

1.4 DVD Super Multi (+-R Double Layer)) 1 Hardware Overview Qosmio F40/F45 Maint enance Manual 25 1.5 HD DVD-ROM The HD DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum , the drive can play back a DVD at 8x speed, read HD DVD ROM at 1x speed, CD- ROM at 24x speed, and write CD-R at 16x sp eed, CD-RW at 4x speed, US CD-[...]

1 Hardware Overview 1.6 HD DVD-R Qosmio F40/F45 Maint enance Manual 26 1.6 HD DVD-R The HD DVD-R drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At m aximum, the drive can play back a DVD at 8x spee d, read HD DVD ROM at 1x speed, HD DVD-R at 1x speed ,CD-ROM at 24x speed, and write CD -R at 16x speed, CD-RW at 4x speed, US CD-RW at 10x[...]

1.8 Batteries 1 Hardware Overview 1.7 Power Supply The power supply unit provides many different voltages for the system board and perform s the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the computer. y Checks whether the battery pack is connected to the computer. y Monitors the DC[...]

1 Hardware Overview 1.7 Power Supply 1.8 Batteries The computer has the following two types of batteries:  Main Battery Pack  Real Time Clock (RTC) Battery Table 1-5 lists the specifications of these batteries. Table 1-5 Battery Specifications Battery Ty pe Material Output voltage Capacity Main Battery Pack 6 Cell Lithium Ion 10.8 V 4000 mAh [...]

1.8 Batteries 1 Hardware Overview Qosmio F40/F45 Maint enance Manual 29 Table 1-6 Quick/Normal Charging Time State Charge Time Off-State Charge 6 Cell About 4 hours max On-State Charge 6 Cell About 4~10 hours max NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently acces[...]

2 Troubleshooting 2 概要 Chapter 2 Troubleshooting 2-i Qosmio F40/F45 M aintenance Manual[...]

2 Troubleshooting Chapter 2 Contents 2.1 Outline .................................................................................................................... 2-1 2.2 Basic Flowchart ...................................................................................................... 2-2 2.3 Power Supply ....................................[...]

2 Troubleshooting 2.10 SD/SD-IO/MS/MS pro/MMC/XD Card .............................................................. 2-21 Procedure 1 Test Program Check ................................................................. 2-21 Procedure 2 Connector Check ...................................................................... 2-21 2.11 Finger Print (Opt[...]

2 Troubleshooting Figures Figure 2-1 Basic flowchart(1/2)....................................................................................... 2-3 Tables Table 2-1 HDD error code and status ........................................................................... 2-13 2-iv Qosmio F40/F45 Maintenance Manual[...]

2.1 Outline 2 Troubleshooting 2.1 Outline This chapter describes the fault diagnosis proced ures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System Board 2. 2.5-inch HDD 3. Keyboard 4. Display 5. ODD drive 6. LAN 7. SD/SD-IO/MS/MS pro/MMC/XD 8. Finger Print 9. Speaker 9. IEEE 1394 10. Cooling m odule[...]

2 Troubleshooting 2.2 Basic Flowchart 2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flow chart steps, verify the following:  Ask the user if a password has been register ed and, if so, ask him or her to enter the password. If the user has forgott[...]

2.2 Basic Flowchart 2 Troubleshooting Star t Connect the AC Adapter Figure 2-1 Basic Flowchart (1/2) DC IN LED on ?? BATTERY LED on ?? Turn the power on. Any error message displayed ?? Message "In Touch with Tomorrow Toshiba" displayed Follow the power supply diagnostic p rocedure in Section 2.3 N o Follow the power supply diagnostic p ro[...]

2 Troubleshooting 2.2 Basic Flowchart Figure 2-1 Basic Flowchart (2/2) Keyboard works well ?? Follow the keyboard diagnostic procedure in Section 2.6 1 N o Insert Bootable CD into ODD Diagnostic Program Loaded ?? Perform each test with the diagnostic program. Any error detected by the diagnostic program ?? Perform the continuous test to check if th[...]

2.2 Basic Flowchart 2 Troubleshooting If the diagnostic program cannot detect an er ror, the error may be intermittent. Run the continuous test program repeatedly to isolate th e problem. Check the log utilities function to confirm which diagnostic test detected th e error, then perform the appropriate troubleshooting procedures as follows: 1. If a[...]

2 Troubleshooting 2.3 Power Supply 2.3 Power Supply The power supply in the computer controls ma ny functions and com ponents. To check if the power supply is defective or malfunctioning, foll ow the troubleshooting procedures below as instructed. Procedure 1 Power Icon Check Procedure 2 Connection Check Procedure 3 Replacement Check Procedure 1 Po[...]

2.3 Power Supply 2 Troubleshooting  DC IN LED DC IN LED Power supply status On in Blue DC power bei ng supplied (from the AC adapter) Off Battery damage and can’t charg e duri ng DC-in. Off Else If the DC IN LED off, follow the steps below: 1. Remove the battery pack and the AC ad apter to shut off power supply to the computer. 2. Attach the b[...]

2 Troubleshooting 2.3 Power Supply Procedure 2 Connection Check Power is supplied to the system board as illustrated below: AC adaptor System board AC power cord AC adaptor cord Battery pack Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugge[...]

2.4 System Board 2 Troubleshooting 2.4 System Board To check if the system board is defectiv e or malfunctioning, f ollow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check Procedure 1 Message Check When the power is turned on, the system perf orms the self-diag[...]

2 Troubleshooting 2.4 System Board Procedure 2 Test Program Check The maintenance test program contains seve ral program s for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Hard Disk test 6. Mouse test 7. SD Card[...]

2.5 2.5-inch HDD 2 Troubleshooting 2.5 HDD To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Procedure 4 Test Program Check Procedure 5 Connector Ch eck and Replacement Check CAUTION: The conten[...]

2 Troubleshooting 2.5 2.5-inch HDD create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3. Check 3 If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Then rest[...]

2.5 2.5-inch HDD 2 Troubleshooting Procedure 4 Test Program Check Run the HDD test program stored on the maintena nce test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are list[...]

2 Troubleshooting 2.5 2.5-inch HDD Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Di sassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connect ors have been firmly connected to the HDD, system board and CPU. HDD System board C[...]

2.6 Keyboard 2 Troubleshooting 2.6 Keyboard To check if the computer’s keyboard is defective or malf unctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the Keyboard test availa ble as part of the maintenan c[...]

2 Troubleshooting 2.7 Display 2.7 Display To check if the computer’s display is def ective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Ch eck and Replacement Check Procedure 1 External Monitor Check Connect an external monitor[...]

2.7 Display 2 Troubleshooting Check 3 The FL may be fault y. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. Check 4 The FL inverter board may be fa ulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5. Check 5 Make sure the LCD/FL cable has been fir[...]

2 Troubleshooting 2.8 ODD Drive 2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 ODD Cleaning Check 1. Turn off the pow[...]

2.8 ODD Drive 2 Troubleshooting Check 3 The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not function ing properly, perform Check 4. Check 4 The system board m ay be faulty. Replace it w ith new one follow ing the instructions in Chapter 4. If the ODD drive is still not fu[...]

2 Troubleshooting 2.9 LAN 2.9 LAN To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the LAN check program available as pa rt of the m aintenance test prog[...]

2.10 SD Card/Memory Stick 2 Troubleshooting 2.10 SD/SD-IO/MS/MS pro/MMC/XD Card To check if the computer’s SD/SD-IO/MS/MS Pro/MMC/XD Card is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the SD/SD-IO/MS/MS Pr[...]

2 Troubleshooting 2.11 Finger Print (Optional) 2-22 Qosmio F40/F45 Maintenance Manual 2.11 Finger Print (Optional) To check if the computer’s Finger Print is defective or m alfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the[...]

2.12 Troubleshooting Audio Test 2 Qosmio F40/F45 Maintenance Manual 2-23 2.12 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Execute the Audio te[...]

2 Troubleshooting 2.13 IEEE 1394 Test 2-24 Qosmio F40/F45 Maintenance Manual 2.13 IEEE 1394 Test To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check Procedure 1 Test Program Check Execute the IEEE 1394 test progra[...]

2.14 Troubleshooting Cooling Module 2 Qosmio F40/F45 Maintenance Manual 2-25 2.14 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, f ollow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Ch eck and Replacement Check Procedure 1 Test Program Check Exec[...]

Chapter 3 Diagnostic Programs[...]

3 Diagnostic Programs Chapter 3 Contents 3.1 General .......................................................................................................................... 1 3.2 Quick Start .................................................................................................................... 3 3.2.1 Quick Test ....................[...]

3 Diagnostic Programs 3.6 Memory Test ............................................................................................................... 34 3.7 Storage ........................................................................................................................ 40 3.8 Video ...................................................[...]

[...]

3.1 General 3 Diagnostic Programs 3.1 General This chapter explains the dia gnostic programs which tests and di agnoses the functions of the hardware components of this computer. The di agnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NOTE 1: This Diagnostic supports Honolulu10/10G NOTE 2: Before running a test, be su[...]

3 Diagnostic Programs 3.1 General Before running the diagnostic programs, get the following tools prepared:  A Service Diagnostic BOOT CD  A Formatted FLOPPY DISK  A Test Media CD (A-BEX TEST CD-R OM TCDR-702)(for CD-ROM test)  A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1)  An External Monitor (for DISPLAY test)  A CD-ROM[...]

3.2 Quick Start 3 Diagnostic Programs 3.2 Quick Start When the system is booting from Service Diagnos tic CD, the following screen will be displayed: Please select a test item or select 0 to exit to Free -DOS: 3.2.1 Quick Test When this item is selected, the syste m will run the configured test items and generate a test report automatically. When t[...]

3 Diagnostic Programs 3.2 Quick Start Select ‘Test Mouse’ or press F8 to run the test. The prompt inform ation would be displayed in the screen as below. This test item needs user to verify whether th e mouse works normally. The test result will be displayed in the f ollowing screen: 4 QosmioF40 /F45，dynabook Q osmio F40 Maintenance Ma nual[...]

3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highl ight a test item by us ing arrow keys, then, press Enter to start. If there are parameters pr ovided, user should set para meters in the parameter dialog window. CPU Speed Test (Step by Step): 1. Select test item: Select System — CPU — CPU Speed , then, press th[...]

3 Diagnostic Programs 3.2 Quick Start 3. Test Result System will automatically run and display the tes t result as follows: Following is the comparison report of the two testing m ethods mentioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the para[...]

3.2 Quick Start 3 Diagnostic Programs 3.2.3 Keyboard Layout test The test purpose is to ch eck whether 18 kinds of Europ ean keyboards run well during the test procedure. When users choose the ite m , the names of these countries will be displayed on the screen for user choice. User press any index of token in ASCII, and the program will test the k[...]

3 Diagnostic Programs 3.2 Quick Start When the user has checked all the keys and all the keys in the screen have changed color, the diagnostics program would automa tically end the test and report the pass information. If keyboard test fails, program will terminat e the test and report the fail information when it is time to timeout. The test will [...]

3.2 Quick Start 3 Diagnostic Programs User can press any key to exit the program. 3.2.8 DMI Write In addition to reading the DMI information, DMI Write also permits a ttributes editing and updating: Manufacture, Product Name, Ve rsion, Serial Number, and OEM Part Number, etc. The following screen will be d isplayed: In this screen, there are two li[...]

3 Diagnostic Programs 3.2 Quick Start During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI W rite. The confirmation screen is as below: The attributes that have been modified woul d be marked in red; otherwise in yellow. User could press F2 to save t[...]

3.2 Quick Start 3 Diagnostic Programs 3.2.11 Finger Printer In formation Clear Select this item to clear all the infor mation in the FP Device. 3.2.12 System Information This function is used to read the system in formation. When the test is com pleted, a file named System.log will be saved in the define d lo cation. During the reading process, the[...]

3 Diagnostic Programs 3.2 Quick Start User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current pr ogram. On the left column, the components information is listed and us er can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component. On the right column, t[...]

3.2 Quick Start 3 Diagnostic Programs 3.2.15 The Diagnostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Erro r L ist, Test Item’s Title, Status Bar and Message Box. 1. Diagnostics Windows When a test item is running, a Diagnostics Windows is [...]

3 Diagnostic Programs 3.2 Quick Start 3. USER BREAK Pressing ESC key to interrupt the test, USER BR EAK message box would be prompted out in the central of Diagnostics Window for th e user to select the following actions:  CONTINUE ---- Contin ue the test;  SKIP ---- Stop the sub-item of current test item to go to the next item’s test;  [...]

3.2 Quick Start 3 Diagnostic Programs  Current Loop Count : In LOOPBOUND mode, it will di splay the total LOOP number planning to execute and the current LOOP number have been finished, e.g. ‘COUNT: 01/01’ in the above screen;  CPU Temperature : Detect the temperature in the cu rrent CPU, e.g. ‘CPU: 49C’ in the above screen;  Remai[...]

3 Diagnostic Programs 3.3Option 3.3 Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s param eters and t hose parameters created by the LOG file. Options Menu Notes: • Select All/None Items Switch between selecting a ll test items and selecting none. T he hot key is F6 . •[...]

3.3 Option 3 Diagnostic Programs Configure batch parameters and a ll the test item’s param eters . • Load Batch Parameters Upload all the test items and the parameters to the *.ini f ile. • Save Batch Parameters Save all the parameters and the test item s that are configured in the editor to a specified file. • Log Parameters Configure LOG [...]

3 Diagnostic Programs 3.3Option • Test Order Specify the order of the test items. C hoose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. • Test Options Choose one of the following options: 9 Wait On Error Wait for further confirmation while an error occurs. 9 Break On Error[...]

3.3 Option 3 Diagnostic Programs 9 Monitor CPU Thermal Monitor the CPU temperature. • Test Mode 9 LOOPBOUND The chosen test items will run repeatedly accord ing to the times specified in the 'Number of Loops'. 9 TIMEBOUND The chosen test items will run for an exte nt tim e specified in 'Time Limit Hrs' and 'Time Limit Min[...]

3 Diagnostic Programs 3.3Option • Interactive If the item is enabled during the test, the te s t items that need user to response can run normally, such as PS2 Mouse te st; If it is disabled, those test items will report FAIL. Whether the option here is enabled, it only affects the current test item. • Parameters For the test items with specifi[...]

3.3 Option 3 Diagnostic Programs In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files. QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 21[...]

3 Diagnostic Programs 3.3Option 3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service DiagnosticsOptions - Generate Report. • Report Destination If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with the name specified in 'Log File Name' will be gener[...]

3.3 Option 3 Diagnostic Programs If selecting this parameter, erro rs and time will be recorded only when the test fails. 9 Append to Old Log File If selecting this parameter, the new lo g will be added to the old one. 9 Log Device Info on Fail If selecting this parameter, deta ils of the failed test will be recorded. • Log file Name Specify the [...]

3 Diagnostic Programs 3.3Option In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: • ↑ , ↓ Scroll a line backward or forward on the screen. • Page Up, Page Down 24 QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual[...]

3.3 Option 3 Diagnostic Programs Scroll a page backward or forward on the screen. • Esc Exit the Log viewer. • F1 Display the Help information about the Log viewer operations and the functional keys. • Ctrl+Home Go to the start of the log file. • Ctrl+End Go to the end of the log file. • Ctrl+F3 Prompt the search dialogue for the user to [...]

3 Diagnostic Programs 3.3Option Base Memory Test : PASS Extended Memory Test : PASS End Time: Wed Jul 05 10:47:51 2006 <Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10 [MSTPad] Begin Time: Wed Jul 05 10:48:54 2006 Touch Pad Test : FAIL ITEM TEST FAIL Function ID :502 Error Code :50202 Error Message :Touch Pad Te[...]

3.4 Subtests 3 Diagnostic Programs 3.4 Subtests Test Group Sub Item ID Subtest Test ID Test items Internal Name System 01 CPU 01 Basic Functionality Test [CPUBasicFun] 02 CPU Speed [CPUSpeed] 03 Coprocessor NPU Basic Functions NPU Interrupt Coprocessor [NPUFun ] [NPUInterrupt] 04 CPU Information [CPUInformation] 05 CPU Protected Mode [Protect] 0 6 [...]

3 Diagnostic Programs 3.4 Subtests 02 Random Increment Read/Write [RandIncr] 11 Data Bus Tes t [DataBus] 12 Memory Speed Test [MemSpeed] Storage 01 HDD 01 Sequential/Random R/W [SeqRdRW1] 02 Sequential/Random Seek [Seek1] 03 Performance [Perform1] 04 Controller Check [Controller1] 05 Diagnostic Read/Write [DiagRW1] 06 SMART Test [SMART1] 02 ODD 01 [...]

3.4 Subtests 3 Diagnostic Programs 04 1 280 X 800 Video Modes VESA 1 280 x 800 x256 Mode VESA 1 280 x 800 x64K Mode VESA 1 280 x 800 x32 K Mode VESA 1 280 x 800 x 16 K Mode VESA 1 280 x 800 x32bit Mode [V1 280800 _15] [V1 280800 _16] [V1 280800 _24] [V1 280800 _32] 04 VESA Video Memory [VESAMEM] 05 AGP Test [AGP] 06 LCD Panel Test [ LCDPanel] 07 Re[...]

3 Diagnostic Programs 3.5 System Test 3.5 System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU 1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, whi[...]

3.5 System Test 3 Diagnostic Programs CPU Speed Comparison --Whether you want to make a comparison of the CPU speed with the value set in ‘E xpected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’. Expected CPU Speed --Specify the expected CPU Speed value you want for further comparison. Allowable Error Rate -- Specify the Allowabl[...]

3 Diagnostic Programs 3.5 System Test 6. MMX The test item is to confirm whether the CPU supports MMX instru ctions. Subtest 02 Boards 1. DMA Controller This test item is to check whethe r the DMA controller works norm ally. 2. Interval Timer This test item is to check whether the Interval Timer (18.2Hz, 55ms) works normally. 3. Clock/Calendar This[...]

3.5 System Test 3 Diagnostic Programs parameter setting dialog window. Set the range of Speed that is to be tested, then choose the OK button to test it. It will be displayed as follows: QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 33[...]

3 Diagnostic Programs 3.6 Memory Test 3.6 Memory Test This test module is to check whet her the mem ory chip works norm ally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that in cludes two sub-items -- ROM Read and ROM Write Protection. RO M Read is to check whether BIOS ROM could be correctly read out, ROM Wr ite Protec[...]

3.6 Memory Test 3 Diagnostic Programs Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m e mory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minut e) of the defi[...]

3 Diagnostic Programs 3.6 Memory Test Pattern Size: Choose the pattern size – BY TE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the m e mory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minut e) of the defi[...]

3.6 Memory Test 3 Diagnostic Programs Test Range: Specify the test coverage range of Extended Memory. If user chooses Total Size, it means that the whole Extended Memory will be tested. Although user can inpu t the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Memory will be [...]

3 Diagnostic Programs 3.6 Memory Test The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 P attern’. Subtest 07 Memory Address This test item is to check short and open issue on memory address lines . Subtest 08 Refresh Test This test item is to check wh[...]

3.6 Memory Test 3 Diagnostic Programs This test item is to check the data -tr ansferring rate for the cache memory and the system memory. QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 39[...]

3 Diagnostic Programs 3.7 Storage 3.7 Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows: Password ： hard disk 1. Sequential/Random R/W This test item is to check t[...]

3.7 Storage 3 Diagnostic Programs LBA Start, LBA End --Specify the start and end byte in LBA (Large Block Address). Percent —Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined [...]

3 Diagnostic Programs 3.7 Storage Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking spee[...]

3.7 Storage 3 Diagnostic Programs The ODD test runs on ID E CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and perf ormance. 1. Controller Test Check the CDROM controller’s status. 2. Data Transfer Rate Check the data transfer rate of the ODD dr ive. It will read data from the ODD disc and calculate the data transfer ra[...]

3 Diagnostic Programs 3.10 Peripheral 3.8 Video This test item tests the video by: 1. displaying the figures in different graphic modes. 2. displaying the property and color of the characters in different text modes. User will confirm whether each video m ode works normally by judging whether the display is correct. It checks whether the video mem [...]

3.10 Peripheral 3 Diagnostic Programs It would display the below texts of th e different attributes in the screen: 1. Text in normal attribute; 2. Text in blinking normal attribute; 3. Text in inverse attribute; 4. Text in blinking inverse attribute; 5. Text in hi-intensity attribute; 6. Text in blinking hi-intensity attribute; Users need to check [...]

3 Diagnostic Programs 3.10 Peripheral 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a ch aracter defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foregroun[...]

3.10 Peripheral 3 Diagnostic Programs In the test, user is required to respond according to the instru ction in the screen. Subtest 02 640 * 480 VGA Mode This test item is to check whethe r 680*480 VGA Text mode works normally. In the test, user is required to respond according to the instru ction in the screen. QosmioF 40/F45，dy nabook Q osmio F[...]

3 Diagnostic Programs 3.10 Peripheral Subtest 03 VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respon d following the instruction in the screen. 1. 640X480 Video Modes Test 2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 1 280 X 800 Vi[...]

3.10 Peripheral 3 Diagnostic Programs If press Ctrl+Break to force the test to term inate during execution of VESA Video Memory, the test program will not operate and display properly in f u rther tests. Subtest 05 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Su[...]

3 Diagnostic Programs 3.10 Peripheral Subtest 07 Register Test This test item is to check whether th e registers of the video adapter works normally. Subtest 08 Color Purity Test This test item is to check whether th e sy stem (the video adapter and the display) could display the purity color of re d, green, blue, black and white. In the test, user[...]

3.10 Peripheral 3 Diagnostic Programs Subtest 10 DAC/Palette Address This test item is to check the functio n of DAC registers and Palette registers. In the test, user is required to respond according to the instru ction in the screen. QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 51[...]

3 Diagnostic Programs 3.10 Peripheral 52 QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual[...]

3.10 Peripheral 3 Diagnostic Programs 3.9 Communication (COMM) Subtest 01 LAN Card This test item is to check whether the m odule can detect the exis tence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Detect the vendor ID of the network card. 3. MAC [...]

3 Diagnostic Programs 3.10 Peripheral 3.10 Peripheral Subtest 01 Keyboard This test item is to check wh ether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Led Test Check whether the keyboard led works normally. If Power switchVolumeCapsNum ScrollAVButtonDC-In PowerB[...]

3.10 Peripheral 3 Diagnostic Programs If PowerBatteryBridgeWireless turn on with Orange,click YES to continue,else click No. If Odd turn on with Orange,clic k YES to continue,else click No. QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 55[...]

3 Diagnostic Programs 3.10 Peripheral If HDD turn on with Orange,click YES to continue,else click No. If all Keyboard LEDs Test normal ， It will be displayed as follows: 3. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02 Mouse Test Check whether the point devices work normally. 1. Touch Pad Before test To[...]

3.10 Peripheral 3 Diagnostic Programs QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 57 At the below screen of Touch Pad test, us er can press the left button, right button, and move the mouse to verify its functions for times, and the te st will end either by user break or test time is out.[...]

3 Diagnostic Programs 3.11Error Codes and Description 58 QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee ’, and ‘dd’ is the device ID (1 ~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is th e error code of device (2 chars); th e rang[...]

3.11Error Codes and Description 3 Diagnostic Programs QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 59 04 (XMS)Memory Problem The test pattern read out from the extension memory is different from the one that has been written in this address. As above. 05 (XMS) Out Of Range Wrong parameters se tup. Check and reset the parameters. 06 Ad[...]

3 Diagnostic Programs 3.11Error Codes and Description 60 QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 17 PCI to ISA Bridge Error PCI-ISA bridge errors. Repeat multiple times. If there is always the same error, replace the board. 18 ESCD Error ESCD errors. As above. 53 ACPI Table Test Error Errors with the ACPI table test. As above. 34[...]

3.11Error Codes and Description 3 Diagnostic Programs QosmioF 40/F45，dy nabook Q osmio F40 Maintenanc e Manual 61 16 AGP Test Error AGP configuration register errors. Check and see whether the AGP video card has any physical problem. 17 LCD Panel Test Error Lower LCD color resolution. Replace the LCD. 19 Register Test Error Physical problems with[...]

3 Diagnostic Programs 3.11Error Codes and Description 05xx Mouse 01 Touch Pad Test Fail Touch Pad Test Fail Check the mouse connection and repeat the test. 28xx 1394 01 Can not find IEEE1394 controller Don’t support 139 4. 20xx IDE-HDD 01 Get Parameter Fail ! Wrong test parameters are input by user. Reinput the correct parameters. 02 Write Patter[...]

3.12 Quick Test Item List 3 Diagnostic Programs 3.12 Quick Test Item List Device Test Items Comment CPU Basic Functionality N PU Basic Functions CPU Information Memory BIOS ROM Cache Me mory Bit Stuck High Test 10% or 3 minutes Bit Stuck Low Test 10% or 3 minutes Address Test Board Interval Timer Clock / Calendar ACPI Test FAN FAN Speed Video 1024X[...]

Chapter 4 Replacement Procedures 4 1[...]

4 Replacement Procedures 4-ii Qosmio F40/F45 Maintenance Manual[...]

4 Replacement Procedures Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 Safety Precautions ................................................................................................ 4-2 Before You Begin ................................[...]

4 Replacement Procedures Disassembling the ODD Bay Module................................................................ 4-25 Assembling the ODD Bay Module .................................................................... 4-26 4.4 Speaker Cover and Keyboard .................................................................................. 4-27 [...]

4 Replacement Procedures 4.14 CPU ....................................................................................................................... ... 4-50 Removing the CPU ............................................................................................ 4-50 Installing the CPU .....................................................[...]

4 Replacement Procedures Installing the Touch Pad and Button Board ....................................................... 4-71 4.24 Speakers .................................................................................................................. . 4-72 Removing the Speakers.................................................................[...]

4 Replacement Procedures Figures Figure 4-1 Removing the battery pack.................................................................................. 4-8 Figure 4-2 Removing the PCI Express card or PC card ...................................................... 4-10 Figure 4-3 Removing the mem ory card .............................................[...]

4 Replacement Procedures Figure 4-32 Sub-speaker, USB cable, TV tuner splitter card and audio board .................. 4-57 Figure 4-33 Removing the display mask ............................................................................ 4-59 Figure 4-34 Removing the FL inverter board ...............................................................[...]

4.1 General 4 Replacement Procedures 4 1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures m ay not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down [...]

4 Replacement Procedures 4.1 General Safety Precautions Before you begin to disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible wi[...]

4.1 General 4 Replacement Procedures CAUTION: 1. Before replacing a component, make su re that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. 2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, [...]

4 Replacement Procedures 4.1 General Before You Begin Before you begin to disassembly the computer, keep in m ind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disa[...]

4.1 General 4 Replacement Procedures Disassembly Procedures The cable connectors come in these two basic types:  Pressure plate connectors  Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the [...]

4 Replacement Procedures 4.1 General Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipm ent. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components. The equipment and t[...]

4.1 General 4 Replacement Procedures Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows:  Screws of an even-numbered length Brown  Screws of an odd-numbered length White  Screws of a special length Black Screws of a special length are those of a length h[...]

4 Replacement Procedures 4.1 General Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer upside d[...]

4.1 General 4 Replacement Procedures Installing the Battery Pack Install the battery pack according to the following procedures and Figure 4-1. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or re[...]

4 Replacement Procedures 4.1 General Removing the PCI Express Card or Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are[...]

4.1 General 4 Replacement Procedures Installing the PCI Express Card or Optional PC Card Install the optional PC card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and is seated securely. 2. After checking that the PC card is seated secu[...]

4 Replacement Procedures 4.1 General Removing the Memory Card Remove the mem ory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Push the memory card to be rem oved until it stops then release the memory card. 3. When the mem ory card pops out, grasp [...]

4.1 General 4 Replacement Procedures Installing the Memory Card Install the memory card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the memory card gently until it stops and is seated securely. 2. Checking that the memory card is seated securely. After the PC card is i[...]

4 Replacement Procedures 4.1 General Removing the Optional Memory Remove the optional mem ory (module) according to the following procedures and Figures 4- 4, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1.[...]

4.1 General 4 Replacement Procedures Installing the Optional Memory Install the optional memory (m odule) according to the following procedures and Figures 4-4, after checking that the computer is turned off in boot mode. Note: The slot A is reserved for main memory . Use the slot B for expanded memory. If only one card is installed, use the slot A[...]

4 Replacement Procedures 4.1 General Removing the B-CAS Card (For JAPAN model only) Remove the mem ory card according to the following procedures and Figure 4-5, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Pull the B-CAS card to be removed, grasp it and pull it out. B CAS card or Smart card - B CAS cover [...]

4.1 General 4 Replacement Procedures Installing the B-CAS Card (For JAPAN model only) Install the memory card according to the following procedures and Figure 4-5, after checking that the computer is turned off in boot mode. 1. Insert the B-CAS card gently until it stops and is seated securely. 2. Checking that the B-CAS card is seated securely. Af[...]

4 Replacement Procedures 4.2 HDD 4.2 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4-6, 4- 7. 1. Remove the one M2x5 flat head screw HDD cover screws [...]

4.2 HDD 4 Replacement Procedures 3. Remove the HDD and 2 nd HDD pack by pulling on the tab attached to the pack, following the direction of the arrows. NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 4. Place the HDD pack on a flat surface (such as a desk), and remove the two [...]

4 Replacement Procedures 4.2 HDD Installing the HDD Install the HDD according to the following procedures and Figures 4-6, 4-7. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD chassis. 2. Secure the HDD and its chassis with the two M3x4 black flat head screws with M3x4 white head screws. CAUTION: To prevent the HD[...]

4.3 ODD Bay Module 4 Replacement Procedures 4.3 ODD Bay Module Removing the ODD Bay Module (For Non-tray Module) NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to [...]

4 Replacement Procedures 4.3 ODD Bay Module Installing the ODD Bay Module (For Non-tray Module) Install the ODD bay module according to the following procedures and Figures 4-8. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Place the ODD bezel in the correct position. 4. Secure the[...]

4.3 ODD Bay Module 4 Replacement Procedures Removing the ODD Bay Module (For Standard Module) NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following proce[...]

4 Replacement Procedures 4.3 ODD Bay Module Installing the ODD Bay Module (For Standard Module) Install the ODD bay module according to the following procedures and Figures 4-9. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Secure the ODD bay module with two M2x4 black flat head sc[...]

4.3 ODD Bay Module 4 Replacement Procedures Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1. Remove four M2x3 black flat head screws. 2. Remove the bracket. M[...]

4 Replacement Procedures 4.3 ODD Bay Module ODD bezel ODD bay module Latch Figure 4-11 Removing the Bezel from the ODD drive Assembling the ODD Drive Assemble the ODD drive according to the following procedures and Figure 4-10, 4-11. 1. Place the ODD bezel in the correct position and secure the following 4 latches. 2. Seat the bracket and secure it[...]

4.4 Speaker Cover and Keyboard 4 Replacement Procedures 4.4 Speaker Cover and Keyboard Removing the Speaker Cover and Keyboard Remove the Speaker Cover and Keyboard according to the following procedures and Figure 4-12, 4-13. 1. Release the following 13 latches on the switch cover, in that order: - five bottom latches - two right and left latches -[...]

4 Replacement Procedures 4.4 Speaker Cover and Keyboard CN12 Keyboard M2 5x2 6 black bin screw .. Figure 4-13 Removing the keyboard 3. Remove two M2.5x2.6 black bind securing screws. 4. Disconnect the keyboard cable from CN12 on the system board. 4-28 Qosmio F40/F45 Maintenance Manual[...]

4.4 Speaker Cover and Keyboard 4 Replacement Procedures Installing the Speaker Cover and Keyboard Install the speaker cover and keyboard according to the following procedures and Figure 4- 12, 4-13. 1. Connect the keyboard cable to CN12 on the system board. 2. Secure the keyboard with two M2.5x2.6 black bind screws. 3. Place the speaker cover in th[...]

4 Replacement Procedures 4.5 Hotkey Board 4.5 Hotkey Board Removing the Hotkey Board Remove the Switch Cover and Switch Board according to the following procedures and Figures 4-14. 1. Disconnect the switch board flat cables from CN4 on the system board. 2. Remove two M2.5x3 white flat head screws. 3. Disconnect the switch board flat cables from CN[...]

4.5 Hotkey Board 4 Replacement Procedures Install the Hotkey Board Install the Hotkey board according to the following procedures and Figures 4-14. 1. Connect the hotkey board flat cables to CN5000 on the switch board. 2. Seat the switch board in the correct position. 3. Secure the switch board with two M2.5x3 white flat head screws. 4. Connect the[...]

4 Replacement Procedures 4.6 MDC Module 4.6 MDC Module Removing the MDC Module Remove the MDC Module (Modem Daughter Card) according to the following procedures and Figures 4-13, after checking that the computer is turned off in boot mode. CAUTION : Remove the MDC module after turning off the computer. If this is violated, the computer or MDC modul[...]

4.6 MDC Module 4 Replacement Procedures Installing the MDC Module Install the MDC module according to the following procedures and Figures 4-15, after checking that the computer is turned off in boot mode. CAUTION : Install the MDC module after turning off the computer. If this is violated, the computer or MDC module can be damaged. CAUTION : Do no[...]

4 Replacement Procedures 4.7 Wireless LAN Card 4 1 4.7 Wireless LAN Card Removing the Wireless LAN Card Remove the wireless LAN card according to the following procedures and Figure 4-16. CAUTION : Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with[...]

4.7 Wireless LAN Card 4 Replacement Procedures Installing the Wireless LAN Card Install the wireless LAN card according to the following procedures and Figure 4-16. 1. Insert the wireless LAN card into the connector an angle of 45 degrees. 2. Press down on the wireless LAN card to secure it with two M2x3 white bind screws. 3. Connect the three ante[...]

4 Replacement Procedures 4.8 Robson Card 4.8 Robson Card Removing the Robson Card Remove the Robson card according to the following procedures and Figure 4-17. CAUTION : Do not touch the connectors on the Robson card and in the computer with your bare hands. Robson cards can fail if they are contaminated with sweat, natural oils, etc. from your han[...]

4.8 Robson Card 4 Replacement Procedures Installing the Robson Card Install the Robson card according to the following procedures and Figure 4-17. 1. Insert the Robson card into the connector an angle of 45 degrees. 2. Press down on the Robson card to secure it with two M2x4 white bind screws. CAUTION : Do not touch the connectors on the Robson car[...]

4 Replacement Procedures 4.9 Display Assembly 4.9 Display Assembly Removing the Display Assembly CAUTION : Use care to avoid that the antenna cable is not caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-18, 4-19. 1. Turn the computer so the rear is facing you and remo[...]

4.9 Display Assembly 4 Replacement Procedures M2 5x5 white bind screw . CN1 LCD FL cable / Wireless LAN antenna MIC cable CCD cable CN5 CN6 Figure 4-19 Removing the display assembly Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-18, 4-19. 1. Place the display panel in the correct pos[...]

4 Replacement Procedures 4.10 Top Cover 4.10 Top Cover Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-20 and 4-21. 1. Turn the computer upside down and remove the following 14 screws: - fourteen M2.5x8 black bind screws M2 5x8 black flat head screw . M2 5x8 black flat head screw . Figure 4-20 Removin[...]

4.10 Top Cover 4 Replacement Procedures 9. Disconnect the switch board flat cable from CN16. 10. Disconnect the speaker cable from CN3. 11. Lift up the top cover. CN9 CN1000 CN11 CN15 CN13 CN16 Latch CN3 Speaker cable Touchpad flat cable Switch board flat cable Volume board flat cable Bluetooth card cable FLICA flat cable LED board flat cable M2 5x[...]

4 Replacement Procedures 4.10 Top Cover Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-20, 4-21. 1. Seat the top cover, adjusting its position. 2. Secure the following 10 latches on the top cover, in that order: - Three Left latches - Two right latches - Three front latch[...]

4.11 System Board, AC-IN cable 4 Replacement Procedures 4.11 System Board, AC-IN cable Removing the System Board, AC-IN cable NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board, MIC cable, AC-IN cable according to the following procedures and F[...]

4 Replacement Procedures 4.11 System Board, AC-IN cable M2 5x8 black flat head screw . AC IN cable - Audio board cable USB connector cable CN12 Sub speaker - CN803 System board CN19 CN20 Figure 4-23 Removing the system board 7. Disconnect the audio board cable from CN18. 8. Disconnect the USB cable from CN20. 9. Disconnect the sub-speaker cable fro[...]

4.11 System Board, AC-IN cable 4 Replacement Procedures Installing the System Board, AC-IN cable Install the System Board, MIC cable, AC-IN cable according to the following procedures and figure 4-22, 4-23. NOTE: Be careful of the eject button for the PC card. It can be damaged when installing the system board. Make sure it is pushed in. 1. Turn th[...]

4 Replacement Procedures 4.12 VGA Cooling Module and VGA Board 4.12 VGA Cooling Module and VGA Board (for VGA Board Model) Removing the VGA Cooling Module and VGA Board Remove the VGA Cooling Module and VGA Board according to the following procedures and Figure 4-22. 1. Remove two M2x5 black flat head screws. 2. Remove the VGA thermal m odule brack[...]

4.12 VGA Cooling Module and VGA Board 4 Replacement Procedures Installing the VGA Board Install the VGA board according to the following procedures and Figure 4-24. 1. Seat the VGA board. 2. Secure the VGA board with two M2x4 black flat head screws . 3. Secure the VGA board thermal module and VGA board bracket with one M2x4 black flat head screws .[...]

4 Replacement Procedures 4.13 CPU Cooling Module and Fan 4.13 CPU Cooling Module and Fan Removing the CPU Cooling Module and Fan CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause damage to [...]

4.13 CPU Cooling Module and Fan 4 Replacement Procedures Figure 4-26 Applying silicon grease Installing the CPU Cooling Module and Fan Install the cooling Module according to the following procedures and Figures 4-25, 4-26. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the correct position for the mo[...]

4 Replacement Procedures 4.14 CPU 4.14 CPU Removing the CPU Remove the CPU according to the following procedures and Figures 4-27, 4-28 and 4-29. CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. NOTE: FOXCONN CPU socket will be 180 degr[...]

4.14 CPU 4 Replacement Procedures Installing the CPU Install the CPU according to the following procedures and Figures 4-28, 4-29. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. Figure 4-28 Installing th[...]

4 Replacement Procedures 4.14 CPU 3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left. Figure 4-29 Securing the CPU 4-52 Qosmio F40/F45 Maintenance Manual[...]

4.15 TV Tuner 4 Replacement Procedures 4.15 TV Tuner Removing the TV Tuner Remove the TV Tuner according to the following procedures and Figure 4-30. CAUTION: Do not touch the connectors on the TV Tuner and in the computer with your bare hands. TV Tune can fail if they ar e contaminated with sweat, natural oils, etc. from your hands. 1. Remove the [...]

4 Replacement Procedures 4.15 TV Tuner Installing the TV Tuner Install the TV Tuner according to the following procedures and Figure 4-30. 1. Insert the TV Tuner into the connector an angle of 45 degrees. 2. Press down on the TV Tuner to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the TV Tuner and in the compu[...]

4.16 Broadcom Card 4 Replacement Procedures 4.16 Broadcom Card Removing the Broadcom Card Remove the Broadcom card according to the following procedures and Figure 4-31. CAUTION: Do not touch the connectors on the Broadcom card and in the computer with your bare hands. Broadcom card can fa il if they are contaminated with sweat, natural oils, etc. [...]

4 Replacement Procedures 4.16 Broadcom Card Installing the Broadcom Card Install the Broadcom card according to the following procedures and Figure 4-31. 1. Insert the Broadcom card into the connector an angle of 45 degrees. 2. Press down on the Broadcom card to secure it with two M2x2 white bind screws. CAUTION: Do not touch the connectors on the [...]

4.17 Sub-speaker, USB cable, TV Tuner Splitter card 4 Replacement Procedures and Audio Board 4.17 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Removing the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Remove the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board according to the following procedures a[...]

4 Replacement Procedures 4.17 Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Installing the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board Install the Sub-speaker, USB cable, TV Tuner Splitter card and Audio Board according to the following procedures and Figure 4-32. Note: Be careful of the kill switch button for th[...]

4.18 Display Mask 4 Replacement Procedures 4.18 Display Mask Removing the Display Mask Remove the display mask according to the following procedures and Figure 4-33. 1. Remove the following 4 seals on the display module in that order: - Two black seals on the bottom - Two black seals on the top 2. Remove the following 4 screws on the display module[...]

4 Replacement Procedures 4.18 Display Mask Installing the Display Mask Install the display mask according to the following procedures and Figure 4-33. 1. Seat the display mask in the correct position and secure the following 31 latches, in that order: - Eight top latches - Five latches on each of the left and right sides - Thirteen bottom latches 2[...]

4.19 FL Inverter Board 4 Replacement Procedures 4.19 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figures 4-34. 1. Remove one M2.5x4 white flat head screw. FL inverter board LCD FL cable / HV cable M2 5x4 white flat head screw . Figure 4-34 Removing the FL inverter board 2. [...]

4 Replacement Procedures 4.19 FL Inverter Board Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figures 4-34. 1. Connect the LCD/FL cable to LCD/FL connector, and connect the HV cable to the HV connector. 2. Seat the LCD module, FL inverter board in the correct position. 3. Secure the FL inve[...]

4.20 LCD Module 4 Replacement Procedure s 4.20 LCD Modules NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations. NOTE: The LCD/FL cable must be carefully peeled away before disconnecting it [...]

4 Replacement Procedures 4.20 LCD Module M2x3 black flat head screw Left LCD bracket Right LCD bracket M2 5x4 white flat head screw . LCD module M2x3 black flat head screw Figure 4-35 Removing the 15.4-inch LCD module and screws 6. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-36 Removing the 15.4-inch LCD m[...]

4.20 LCD Module 4 Replacement Procedure s Installing the 15.4-inch LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the 15.4-inch LCD module according to the following procedures and Figures 4-35, 4- 36. 1. Turn the LCD upside down. 2. Connect the LCD/FL cable to the LCD module connector. [...]

4 Replacement Procedures 4.21 CCD Board and MIC 4.21 CCD Board and MIC Removing the CCD Board and MIC Remove the FL inverter board according to the following procedures and Figure 4-37. 1. Disconnect the CCD cable from the CCD module connector and rem ove the CCD board. CCD board MIC CCD board cable Figure 4-37 Removing the CCD board and MIC 2. Lif[...]

4.21 CCD Board and MIC 4 Replacement Procedure s Installing the CCD Board and MIC Install the FL inverter board according to the following procedures and Figure 4-37. 1. Connect the CCD module cable to CCD module connector. 2. Seat the CCD module, MIC in the correct position. Qosmio F40/F45 Maintenance Manual 4 - 67[...]

4 Replacement Procedures 4.22 FELICA card, Bluetooth Card and LED Board 4.22 FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Removing the FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Remove the FELICA card(For JAPAN Model Only) and Bluetooth card and LED Board according to the following procedures and Figure 4-38.[...]

4.22 FELICA card, Bluetooth Card and LED Board 4 Replacement Procedure s Installing the FELICA card(For JAPAN Model Only), Bluetooth card and LED Board Install the touch pad and button board accordi ng to the following procedures and Figure 4-38. 1. Connect the FELICA card flat cable to FELICA card and Bluetooth card cable to Bluetooth card. 2. Sea[...]

4 Replacement Procedures 4.23 Touch Pad and Button Board 4.23 Touch Pad and Button Board Removing the Touch Pad and Button Board Remove the touch pad and button board according to the following procedures and Figure 4- 39. 1. Disconnect the touch pad flat cables from J1 on the touch pad. 2. Disconnect the touch pad flat cable from CN3001 on the but[...]

4.23 Touch Pad and Button Board 4 Replacement Procedure s Installing the Touch Pad and Button Board Install the touch pad and button board accordi ng to the following procedures and Figure 4-39. 1. Seat the touch pad, button board touch pad bracket in the correct position and secure it with the five M2x3 black flat head bind screws and two M2x3 bla[...]

4 Replacement Procedures 4.24 Speakers 4.24 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4-40. 1. Remove one M2.5x4 white flat head screw securing the left speaker. 2. Remove two M2.5x4 white flat head screws securing the right speaker. 3. Remove the left and right speakers. M2 5x4 white flat h[...]

4.25 Switch Board and Volume Board 4 Replacement Procedure s 4.25 Switch Board and Volume Board Removing the Switch Board and Volume Board Remove the Switch Board and Volume Board according to the following procedures and Figures 4-41 1. Remove two M2x3 black flat head screws. 2. Remove the switch board. 3. Disconnect the switch board flat cables f[...]

4 Replacement Procedures 4.25 Switch Board and Volume Board Install the Switch Board and Volume Board Install the switch board according to the following procedures and Figures 4-12. 1. Connect the switch board flat cables to CN8000 on the switch board. 2. Seat the switch board in the correct position. 3. Secure the switch board with two M2x3 black[...]

4.26 RJ11 Cable, TV Antenna Connector and B-CAS Card Slot 4 Replacement Procedure s 4.26 RJ11 cable, TV Antenna Connector and B-CAS card Slot Removing the RJ11 cable, TV Antenna Connector and B-CAS card Slot Remove the RJ11 cable, TV Antenna Connector and B-CAS card Slot according to the following procedures and Figure 4-42. 1. Remove the RJ11 cabl[...]

4 Replacement Procedures 4.26 RJ11 Cable, TV Antenna Connector and B-CAS Card Slot Installing the RJ11 cable, TV Antenna Connector and B-CAS card Slot Install the RJ11 cable, TV Antenna Connector and B-CAS card Slot according to the following procedures and Figure 4-42. 1. Seat the B-CAS card slot in the correct position. 2. Secure the B-CAS card s[...]

6000 1 次 Appendices[...]

Apx. A Handling the LCD Module Appendices Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is pro[...]

Appendices Apx. A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do [...]

Apx. A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Qosmio F40/F4[...]

Appendices Apx. A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. A-4 Qosmio F40/F45 Mainte nance Manual[...]

Apx. A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can damage the panel’s polarization. Qosmio F40/F45 Maint enan[...]

Apx. B Board Layout Appendices Appendix B Appendix B Board Layout B.1 System Board Front View Figure B-1 Board Layout (Front View) Qosmio F40/F45 Maintena nce Manual B-1[...]

Appendices Apx. B Board Layout B.2 System Board Back View Figure B-2 Board Layout (Back View) B-2 Qosmio F40/F 45 Maintenance Manual[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-1 Appendix C C-3 C.1 CN1 LCM / FL Inverter Connector (40-Pin) ................................................. C-3 C.2 CN2 Speaker Sub-Woofer Connector (4-Pin) ................................................ C-3 C.3 CN3 Internal Speaker Connector (4-Pin) ......................[...]

Appendices Apx. C Pin Assignments C-2 Qosmio F40/F 45 Maintenance Manual C.32 CN815 ODD Connector (50-Pin) ......................................................................C-21 C.33 CN817 IEEE 1394 Connector (4-Pin) ...............................................................C-21 C.34 CN818 SATA HDD-1 Connector (22-Pin) ....................[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-3 Appendix C Appendix C Pin Assignments System Board C.1 CN1 LCM / FL Inverter Connector (40-Pin) Table C-1 LCM / FL Inverter Connector Pin Assignments (40-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 N$811968 - 3 DGND - 4 N$811968 - 5 DGND - 6 +V3S O 7 LVDS_T[...]

Appendices Apx. C Pin Assignments C-4 Qosmio F40/F 45 Maintenance Manual C.3 CN3 Internal Speaker Connector (4-Pin) Table C-3 Internal Speaker Connector Pin Assignments (4-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 SPK_OUT_L- O 2 SPK_OUT_L+ O 3 SPK_OUT_R- O 4 SPK_OUT_R+ O C.4 CN4 Hot Key Board Connector (16-Pin) Table C-4 Hot Key Board [...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-5 C.7 CN7 Robson Module Connector (52-Pin) Table C-7 Robson Module Connector Pin Assignments (52-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 - - 2 +V3S O 3 - - 4 DGND - 5 - - 6 +V1.5S O 7 - - 8 - - 9 DGND - 10 - - 11 CLK_R_PCIE_MINI1# O 12 - - 13 CLK_R_PCIE_MINI1 O 14[...]

Appendices Apx. C Pin Assignments C-6 Qosmio F40/F 45 Maintenance Manual 5 MS_DATA2_SD_DAT2_SM_D2 I/O 6 MS_CDZ I/O 7 MS_DATA3_SD_DAT3_SM_D3 I/O 8 MS_CLK_SD_CLK_SM_ELWPZ I/O 9 VCC_MC O 10 DGND - 11 MS_DATA2_SD_DAT2_SM_D2 I/O 12 MS_DATA3_SD_DAT3_SM_D3 I/O 13 MS_BS_SD_CMD_SM_WEZ I/O 14 DGND - 15 VCC_MC O 16 MS_CLK_SD_CLK_SM_ELWPZ I/O 17 DGND - 18 - - [...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-7 5 DGND - 6 FILI_PRES# I C.11 CN12 Internal Keyboard Connector (34-Pin) Table C-11 Internal Keyboard Connector Pin Assignments (34-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$850859 I 2 N$850860 I 3 N$850855 I 4 +V3S O 5 SCAN_IN(1) O 6 SCAN_IN(6) O 7 SCAN_IN(5) O 8[...]

Appendices Apx. C Pin Assignments C-8 Qosmio F40/F 45 Maintenance Manual C.13 CN15 Blue Tooth Board Connector (10-Pin) Table C-13 Blue Tooth Board Connector Pin Assignments (10-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 N$634761 O 3 BTRF-E3V O 4 CH_DATA I/O 5 N$1192610 - 6 BTMDL# I 7 CH_CLK I/O 8 USB_R_P6- I/O 9 USB_R_P6+ I/O 1[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-9 C.16 CN18 Wireless LAN Module Connector (52-Pin) Table C-16 Wireless LAN Module Connector Pin Assignments (52-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PCIE_WAKE# I/O 2 +V3S O 3 CH_DATA I/O 4 DGND - 5 CH_CLK I/O 6 +V1.5S O 7 CLKREQ_R_MINI2# I 8 LPC_3S_FRAME# O 9 D[...]

Appendices Apx. C Pin Assignments C-10 Qosmio F40/F45 Maint enance Manual 5 DGND - 6 HPS O 7 HP_OUTL O 8 HP_OUTR O 9 ANAGND - 10 MICS O 11 MIC_L O 12 MIC_R O 13 ANAGND - 14 LINE_S O 15 LINE_L O 16 LINE_R O 17 ANAGND - 18 ANAGND - 19 KILL_SWCH# O 20 +V3A O C.18 CN20 USB Port2 / Port3 Connector (8-Pin) Table C-18 USB Port2 / Port3 Connector Pin Assig[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-11 15 N$838144 - C.21 CN802 HDMI Connector (19-Pin) Table C-21 HDMI Connector Pin Assignments (19-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$1080927 - 2 N$988396 - 3 DGND - 4 HDMI_SDADDC O 5 HDMI_SCLDDC - 6 - - 7 - - 8 HDMI_L_TXC- O 9 DGND - 10 HDMI_L_TXC+ O 11 HDM[...]

Appendices Apx. C Pin Assignments C-12 Qosmio F40/F45 Maint enance Manual C.24 CN807 FAN Connector (3-Pin) Table C-24 FAN Connector Pin Assignments (3-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 N$814474 O 2 DGND - 3 FAN_TACH1 I C.25 CN808 DDR2 DIMM0 Socket (200-Pin) Table C-25 DDR2 DIMM0 Socket Pin Assignments (200-Pin) Pin No. Signal N[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-13 53 DGND - 54 DGND - 55 M_DATA(18) I/O 56 M_DATA(22) I/O 57 M_DATA(19) I/O 58 M_DATA(23) I/O 59 DGND - 60 DGND - 61 M_DATA(24) I/O 62 M_DATA(28) I/O 63 M_DATA(25) I/O 64 M_DATA(29) I/O 65 DGND - 66 DGND - 67 M_DM(3) I/O 68 M_DQS#(3) I/O 69 - - 70 M_DQS(3) I/O 71 DGND - 72 DGND[...]

Appendices Apx. C Pin Assignments C-14 Qosmio F40/F45 Maint enance Manual 127 DGND - 128 DGND - 129 M_DQS#(4) I/O 130 M_DM(4) I/O 131 M_DQS(4) I/O 132 DGND - 133 DGND - 134 M_DATA(38) I/O 135 M_DATA(34) I/O 136 M_DATA(39) I/O 137 M_DATA(35) I/O 138 DGND - 139 DGND I/O 140 M_DATA(44) I/O 141 M_DATA(40) I/O 142 M_DATA(45) I/O 143 M_DATA(41) I/O 144 D[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-15 C.26 CN809 Express Card Connector (26-Pin) Table C-26 Express Cad Connector Pin Assignments (26-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 USB_P4- I/O 3 USB_P4+ I/O 4 CPUSB# I 5 - - 6 - - 7 ICH_3A_ALERT_CLK I/O 8 ICH_3A_ALERT_DAT I/O 9 +V1.5_EXP O 10 +V1.[...]

Appendices Apx. C Pin Assignments C-16 Qosmio F40/F45 Maint enance Manual 27 ACARD_3S_AD24 I/O 28 ACARD_3S_AD25 I/O 29 ACARD_3S_AD26 I/O 30 ACARD_3S_AD27 I/O 31 ACARD_3S_AD29 I/O 32 ACARD_3S_D(2)_RFU I/O 33 ACARD_3S_CLKRUN# I/O 34 DGND - 35 DGND - 36 ACARD_3S_CD1# I/O 37 ACARD_3S_AD2 I/O 38 ACARD_3S_AD4 I/O 39 ACARD_3S_AD6 I/O 40 ACARD_3S_D(14)_RFU[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-17 21 DGND - 22 M_DATA(13) I/O 23 M_DATA(8) I/O 24 DGND - 25 M_DATA(9) I/O 26 M_DM(1) O 27 DGND - 28 DGND - 29 M_DQS#(1) I/O 30 M_CLK_DDR2 O 31 M_DQS(1) I/O 32 M_CLK_DDR2# O 33 DGND - 34 DGND - 35 M_DATA(10) I/O 36 M_DATA(14) I/O 37 M_DATA(11) I/O 38 M_DATA(15) I/O 39 DGND - 40 [...]

Appendices Apx. C Pin Assignments C-18 Qosmio F40/F45 Maint enance Manual 95 +V1.8 O 96 +V1.8 O 97 M_A(5) I/O 98 M_A(4) I/O 99 M_A(3) I/O 100 M_A(2) I/O 101 M_A(1) I/O 102 M_A(0) I/O 103 +V1.8 O 104 +V1.8 O 105 M_A(10) I/O 106 M_A(16) I/O 107 M_A(15) I/O 108 M_RAS# I/O 109 M_WE# I/O 110 M_CS0# I/O 111 +V1.8 O 112 +V1.8 O 113 M_CAS# O 114 M_ODT2 O 1[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-19 169 M_DQS(6) O 170 M_DM(6) I/O 171 DGND - 172 DGND - 173 M_DATA(54) I/O 174 M_DATA(50) I/O 175 M_DATA(55) I/O 176 M_DATA(51) I/O 177 DGND - 178 DGND - 179 M_DATA(56) I/O 180 M_DATA(60) I/O 181 M_DATA(57) I/O 182 M_DATA(61) I/O 183 DGND - 184 DGND - 185 M_DM(7) I/O 186 M_DQS#([...]

Appendices Apx. C Pin Assignments C-20 Qosmio F40/F45 Maint enance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 PCIE_WAKE# I/O 2 +V3S O 3 - - 4 DGND - 5 - - 6 +V1.5S O 7 - - 8 - - 9 DGND - 10 - - 11 CLK_R_PCIE_MINI3# O 12 - - 13 CLK_R_PCIE_MINI3 O 14 - - 15 DGND - 16 - - 17 - - 18 DGND - 19 - - 20 - - 21 DGND - 22 BUF_PLT_RST# O 23 PCIE[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-21 9 DGND - 10 N$1057864 O C.32 CN815 ODD Connector (50-Pin) Table C-32 ODD Connector Pin Assignments (50-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 - - 2 - - 3 - - 4 - - 5 N$630731 O 6 SDD(8) I/O 7 SDD(7) I/O 8 SDD(9) I/O 9 SDD(6) I/O 10 SDD(10) I/O 11 SDD(5) I/O 12[...]

Appendices Apx. C Pin Assignments C-22 Qosmio F40/F45 Maint enance Manual 1 1394_L_TPB0N I/O 2 1394_L_TPB0P I/O 3 1394_L_TPA0N I/O 4 1394_L_TPA0P I/O C.34 CN818 SATA HDD-1 Connector (22-Pin) Table C-34 SATA HDD-1 Connector Pin Assignments (22-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 DGND - 2 SATA_C_TXP0 O 3 SATA_C_TXN0 O 4 DGND - 5 SA[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-23 7 DGND - 8 DCIN_BLED# O 9 PWR_BUF_BLED# O 10 PWR_BUF_OLED# O 11 BAT0_BLED# O 12 BAT0_OLED# O 13 HDD_LED# O 14 ODD_LED# O 15 LED_6IN1 O 16 WLON# O 17 BTIFON# O 18 REC_LED O 19 RESERVE_LED# O 20 DGND - 21 +V5LA O 22 +V5LA O 23 - - 24 CIR_OUT O 25 N$1184408 - 26 L_CIR_RX1 - 27 D[...]

Appendices Apx. C Pin Assignments C-24 Qosmio F40/F45 Maint enance Manual 41 PCI_3S_AD(25) I/O 42 PCI_3S_AD(28) I/O 43 PCI_3S_REQ#(1) I 44 PCI_3S_AD(26) I/O 45 PCI_3S_CBE#(3) I/O 46 PCI_3S_AD(24) I/O 47 PCI_3S_AD(23) I/O 48 N$1051321 - 49 DGND - 50 DGND - 51 PCI_3S_AD(21) I/O 52 PCI_3S_AD(22) I/O 53 PCI_3S_AD(19) I/O 54 PCI_3S_AD(20) I/O 55 DGND - [...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-25 115 XBCLKM-P3P I/O 116 DGND - 117 DGND - 118 DGND - 119 DGND - 120 DGND - 121 BCPWON-P3P I/O 122 - - 123 +V5S O 124 - - C.38 CN2009 TV Tuner Slave Connector (124-Pin) Table C-38 TV Tuner Slave Connector Pin Assignments (124-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O[...]

Appendices Apx. C Pin Assignments C-26 Qosmio F40/F45 Maint enance Manual 53 PCI_3S_AD(19) I/O 54 PCI_3S_AD(20) I/O 55 DGND - 56 PCI_3S_PAR I/O 57 PCI_3S_AD(17) I/O 58 PCI_3S_AD(18) I/O 59 PCI_3S_CBE#(2) I/O 60 PCI_3S_AD(16) I/O 61 PCI_3S_IRDY# I/O 62 DGND - 63 TS-P3V O 64 PCI_3S_FRAME# I/O 65 PCI_3S_CLKRUN# I/O 66 PCI_3S_TRDY# I/O 67 PCI_3S_SERR# [...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-27 C.39 CN3000 Touch Pad Board to Module Connector (12-Pin) Table C-39 Touch Pad Board to Module Connector Pin Assignments (12-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 LEFT_TP O 2 - - 3 - - 4 - - 5 - - 6 RIGHT_TP O 7 GND_TP - 8 GND_TP - 9 IM_CLK_5_F I/O 10 IM_DAT_5[...]

Appendices Apx. C Pin Assignments C-28 Qosmio F40/F45 Maint enance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 +V5S_AB O 2 +V5S_AB O 3 SPDIF_AB O 4 AUDIO_GROUND - 5 AUDIO_GROUND - 6 HPS_AB O 7 HP_OUTL_AB O 8 HP_OUTR_AB O 9 AGROUND_AUDIO - 10 MICS_AB O 11 MIC_L_AB O 12 MIC_R_AB O 13 AGROUND_AUDIO - 14 LINE_S_AB O 15 LINE_L_AB O 16 LINE_[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-29 15 LED_6IN1_DB O 16 WLON#_DB O 17 BTIFON#_DB O 18 REC_LED_DB O 19 RESERVE_LED#_DB O 20 LED_GROUND - 21 +V5LA_LB O 22 +V5LA_LB O 23 - - 24 CIR_OUT_LB O 25 N$1183960 - 26 L_CIR_RX1_LB O 27 LED_GROUND - 28 LED_GROUND - C.45 CN7000 Volume Board to M/B Connector (8-Pin) Table C-45[...]

Appendices Apx. C Pin Assignments C-30 Qosmio F40/F45 Maint enance Manual Pin No. Signal Name I/O Pin No. Signal Name I/O 1 TD+ I/O 2 TD- I/O 3 RD+ I/O 4 LAN_45 I/O 5 LAN_45 I/O 6 RD- I/O 7 LAN_78 I/O 8 LAN_78 I/O 9 N$637812 - 10 LED_LANLINK# I/O 11 N$723050 - 12 N$1167994 - C.49 JACK4000 External Microphone Connector (6-Pin) Table C-49 External Mi[...]

Appendices Apx. C Pin Assignments Qosmio F40/F45 Maint enance Manual C-31 C.52 JACK4003 Video In Connector (6-Pin) Table C-52 Video In Connector Pin Assignments (6-Pin) Pin No. Signal Name I/O Pin No. Signal Name I/O 1 EXCVB1-PXP I 2 - - 3 - - 4 N$1139468 - 5 N$1139473 - 6 TVGND -[...]

Keyboard Scan/Character Codes Appendices Apx. D K eyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06[...]

Appendices Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34 36 H 23 A3 33 F0 33 37 J 24 A4 3B F0 3B *2 38 K[...]

Keyboard Scan/Character Codes Appendices Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code s et 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *1 76 Del E0 53 E0 D3 E0 71 E0 F0 71 *1 79 ← E[...]

Appendices Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (4/4) Cap Code set 1 Code set 2 No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 7 F0 7 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F 20[...]

Keyboard Scan/Character Codes Appendices Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 5 5 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 7 5 I N S E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 7 6 D E L E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79 ← E0 AA E0 4B E[...]

Appendices Keyboard Scan/Character Codes Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Brea k 7 5 I N S E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 7 6 D E L E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 8 0 H o m e E0 2A E0 4[...]

Keyboard Scan/Character Codes Appendices Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 08 7 (7) 47 C7 6C F0 6C 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F[...]

Appendices Keyboard Scan/Character Codes Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm on * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes. D-8 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 US keyboard E.2 Japan (JP) Keyboard Figure E-2 JP keyboard Qosmio F40/F45 Maintenance Manual E-1[...]

Appendices Apx. E Key Layout E.3 Spanish (SP) Keyboard Figure E-3 SP keyboard E.4 Korean (KR) Keyboard Figure E-4 KR keyboard E-2 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.5 Canadian Bilingual (QB) Keyboard Figure E-5 QB keyboard E.6 French (FR) Keyboard Figure E-6 FR keyboard Qosmio F40/F45 Maintenance Manual E-3[...]

Appendices Apx. E Key Layout E.7 German (GR) Keyboard Figure E-7 GR keyboard E.8 Italian (IT) Keyboard Figure E-8 IT keyboard E-4 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.9 Taiwan (TC) Keyboard Figure E-9 TC keyboard E.10 Portuguese (PT) Keyboard Figure E-10 PT keyboard Qosmio F40/F45 Maintenance Manual E-5[...]

Appendices Apx. E Key Layout E.11 DU, UE, US International (USE) Keyboard Figure E-11 USE keyboard E.12 Arabic (AR) Ke yboard Figure E-12 AR keyboard E-6 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.13 Belgian (BE) Ke yboard Figure E-13 BE keyboard E.14 Russian (RU) Keyboard Figure E-14 RU keyboard Qosmio F40/F45 Maintenance Manual E-7[...]

Appendices Apx. E Key Layout E.15 Swiss/Switzerland (SL) Keyboard Figure E-15 SL keyboard E.16 Swedish (SW) Keyboard Figure E-16 SW keyboard E-8 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.17 Norwegian (NO) Keyboard Figure E-17 NO keyboard E.18 Danish (DK) Ke yboard Figure E-18 DK keyboard Qosmio F40/F45 Maintenance Manual E-9[...]

Appendices Apx. E Key Layout E.19 Turke y (TR) Keyboard Figure E-19 TR keyboard E.20 Greek (GK) Keyboard Figure E-20 GK keyboard E-10 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.21 Canadia n Multinational (CM) Keyboard Figure E-21 CM keyboard E.22 Herbrew (HE) Keyboard Figure E-22 HE keyboard Qosmio F40/F45 Maintenance Manual E-11[...]

Appendices Apx. E Key Layout E.23 Czech (CZ) Keyboard Figure E-23 CZ keyboard E.24 Scandinavian (N5) Keyboard Figure E-24 N5 keyboard E-12 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.25 Hungary (HU) Keyboard Figure E-25 HU keyboard E.26 Slovakian (SK) Keyboard Figure E-26 SK keyboard Qosmio F40/F45 Maintenance Manual E-13[...]

Appendices Apx. E Key Layout E.27 Yugoslavia (YU) Keyboard Figure E-27 YU keyboard E.28 Thai (TH) Keyboard Figure E-28 TH keyboard E-14 Qosmio F40/F45 Maintenance Manual[...]

Apx. E Key Layout Appendices E.29 United Kingdom (EN) Ke yboard Figure E-29 EN keyboard E.30 Turkish F (TF) Keyboard Figure E-30 TF keyboard Qosmio F40/F45 Maintenance Manual E-15[...]

Apx. F BIOS Rewrite Procedures Appendices Appendix G Appendix F BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk for the com puter that has renewed BIOS data. Rewriting the BIOS 1. Set the syst[...]

Apx. G EC/KBC Rewrite Procedures Appendices Appendix H Appendix G EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  BIOS/EC/KBC rewriting disk for the computer Rewriting the EC/KBC 1. Set the system to boot mode. [...]