Toshiba Qosmio X70-A/X75-A series инструкция обслуживания

User's Manual Satellite P70-A/P75-A/P70t-A/ P75t-A Qosmio X70-A/X75-A series[...]

Table of Contents Chapter 1 TOSHIBA Legal, Regulatory and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice ..........................................................................[...]

Battery .................................................................................................. 4-28 LAN ....................................................................................................... 4-34 Additional memory module ................................................................ 4-35 Memory media .................[...]

Chapter 1 TOSHIBA Legal, Regulatory and Safety This chapter states the Legal, regulatory and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permissi[...]

The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other[...]

Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s External RGB monitor port, Universa[...]

Ecodesign Directive 2009/125/EC (ErP) and the related implementing measures. This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are conne[...]

VCCI Class B Information (Japan Only) この装置は、クラスＢ情報技術装置です。この装置は、家庭環境で使 用することを目的としていますが、この装置がラジオやテレビジョン 受信機に近接して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従っ[...]

Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006[...]

Battery is a consumption product, since the battery time depends on the usage of your computer. If the battery can not be charged at all, then it is a defect or failure. The changes in battery time is not a defect or failure. Following information is only for India: The use of this symbol indicates that this product may not be treated as household [...]

------------------------ /*===================================================== Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copy[...]

---------------------------------- /* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following con[...]

USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available vers[...]

Disposing of the computer and the computer's batteries Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government. This computer contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace t[...]

Precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct expo[...]

Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat. To keep your computer in prime operating condition, protect your work area from: Dust, moisture, and direct sunlight. Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are[...]

Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage. Clean the plastics of the computer using a slightly water damp[...]

Instruction Manual for Safety and Comfort All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer. Safety Icons Safety icons are used in this manual to bring important information to your attention. Each type of message[...]

Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and [...]

Click Tap the Touch Pad or click the left Touch Pad control button once. Left click the mouse once. Tap the touch screen once (only for touch screen models). Right-click Click the right Touch Pad control button once. Right click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or clic[...]

Series Model Name Short Name Satellite P70-A/P75-A Satellite P70t-A/P75t-A P70-A Qosmio X70-A/X75-A X70-A The computer operations described herein apply to all models unless otherwise stated. Using your computer for the first time Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of th[...]

The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. Always use the TOSHIBA AC adaptor that was included with your c[...]

Figure 2-1 Connecting the power cord to the AC adaptor (2-pin plug for P70-A) Figure 2-2 Connecting the power cord to the AC adaptor (3-pin plug for P70-A) Figure 2-3 Connecting the power cord to the AC adaptor (3-pin plug for X70-A) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC ad[...]

Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. Figure 2-6 Opening the displa[...]

Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Power Condition Descriptions section for more information. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Volume cannot be adjusted during Windo[...]

From the Start screen, you can just start typing to search for what you want. From there, you can easily switch between results for apps, files, and more. Charms Use the Windows Charms to start apps, find documents, set up system components, and perform most other computing tasks. By pointing the mouse pointer to the upper or lower right corner of [...]

unauthorized access. You are allowed to select an option on the Windows login screen by clicking Sign-in options if you have multiple sign-in methods set for a user account. Password authentication is the default sign-in option. Turning off the power The power can be turned off in one of the following modes, either Shut Down Mode, Sleep Mode or Hib[...]

Sleep Mode If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer's main memory so that when you turn on the power again, you can continue working right where you left off. When you have to turn off your c[...]

Benefits of Sleep Mode The Sleep Mode feature provides the following benefits: Restores the previous working environment more rapidly than the Hibernation Mode feature. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Sleep Mode feature. Allows the use of the panel [...]

Do not install or remove a memory module while the computer is in Hibernation Mode, as data will be lost. Do not switch to Hibernation Mode while transferring data to external media, such as USB devices, memory media or other external memory devices, as data will be lost. Benefits of Hibernation Mode The Hibernation Mode feature provides the follow[...]

Data save in Hibernation Mode When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the Hard Disk Drive. After you turn off the computer, and the content of memory has been saved to the Hard Disk Drive, turn off the power to any peripheral devices. Do not turn the computer or devices [...]

Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section. Please handle your computer carefully [...]

DC IN/Battery indicator The DC IN/Battery indicator shows the condition of the DC IN and the battery's charge - white(P70-A)/red(X70-A) indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor. Please refer to the Power Condition Descriptions section for more information on this feature. Powe[...]

Figure 3-3 The left side of the computer (P70-A) 3 4 5 1 2 6 Figure 3-4 The left side of the computer (X70-A) 4 5 1 3 6 1. Security lock slot 4. Universal Serial Bus (USB 3.0) port 2. TV tuner jack* 5. Universal Serial Bus (USB 3.0) port 3. LAN jack 6. Optical disc drive * Provided with some models. Product appearance depends on the model you purch[...]

Universal Serial Bus (USB 3.0) port Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. The port with the icon ( ) has Sleep and Charge function. Please note that it is not possible to co[...]

Figure 3-6 The right side of the computer (X70-A) 2 8 7 1 3 4 5 6 1. Headphone jack 5. HDMI out port 2. Microphone jack 6. External RGB monitor port 3. Universal Serial Bus (USB 3.0) port 7. Cooling vents 4. Universal Serial Bus (USB 3.0) port 8. DC IN 19V jack Product appearance depends on the model you purchased. Headphone jack A 3.5 mm mini head[...]

HDMI out port HDMI out port can connect with Type A connector HDMI cable. External RGB monitor port This port provides 15-pin, analog RGB port. Please refer to the External RGB monitor port pin assignment section for information on external RGB monitor port pin assignment. This port allows you to connect an external RGB monitor to the computer. Coo[...]

Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to the Battery section. Underside The following figures show the underside of the computer. You should ensure that the display is closed b[...]

Battery release latch Slide and hold this latch into its "Unlock" position in order to release the battery pack for removal.For more detailed information on removing the battery pack please refer to the Battery section. Memory module slot The memory module slot allows for the installation, replacement and removal of additional memory modu[...]

Figure 3-11 The front of the computer with the display panel open (P70-A) 1 7 9 8 6 2 3 4 5 7 10 11 13 12 14 9 Figure 3-12 The front of the computer with the display panel open (P70-A touch models) 1 7 8 6 2 3 4 5 7 10 11 13 12 14 9 User's Manual 3-9[...]

Figure 3-13 The front of the computer with the display panel open (X70-A) 1 7 8 6 2 3 4 5 7 10 11 13 12 14 9 9 1. Wireless communication antennas (not shown)* 8. Keyboard 2. Microphone 9. Stereo speakers 3. Web Camera LED 10. Power button 4. Web Camera 11. Touch Pad 5. Microphone* 12. Touch Pad control button 6. Display screen 13. Touch Pad control[...]

Do not point the web camera directly at the sun. Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty. Display screen 43.9cm (17.3") LCD screen, configured with the following resolutions: HD+, 1600 horizontal x[...]

Touch Pad control buttons The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using. Touch Pad ON/OFF indicator Doub[...]

SSD is a large-capacity storage media which uses Solid-State Memory in place of a magnetic disk of the hard disk. Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors. Legal Footnote (Hard Disk Drive (HDD) Capacity) For more information regarding Hard Disk Dri[...]

Graphics Control Some NVIDIA graphics models may include NVIDIA ® Optimus™ technology feature. NVIDIA ® Optimus™ technology intelligently optimizes notebook performance by seamlessly switching between a discrete NVIDIA GPU for great graphics performance and an Intel integrated graphics chip for sustained battery life. Switching is automatic a[...]

This feature can be used if the computer is: running under battery mode using the internal LCD display only The Display Power Saving Technology feature is enabled as the factory default. If you want to disable this feature, you can disable it. The Display Power Saving Technology feature can be disabled in the Intel ® HD Graphics Control Panel/Inte[...]

The NVIDIA ® GeForce Experience TM can notify you of the latest display driver updates for NVIDIA Graphics Controllers. However, Toshiba does not guaranty compatibility of such NVIDIA drivers with your device. TOSHIBA shall not be liable for any damage resulting from NVIDIA’s drivers. Hence, your device shall not be covered under TOSHIBA’s lim[...]

Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates • LED: off Remaining battery capacity is below low battery trigger point • Operates • LED: flashes amber Remaining battery capacity is exhausted Computer shuts down DC IN/Battery indicator Check the DC IN/Batte[...]

Flashing white(P70- A)/red(X70-A) Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. No light Under any other conditions, the indicator does not light. User's Manual 3-18[...]

Chapter 4 Operating Basics This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it. Using the Touch Screen Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the onscreen keyboard, and other items on the touch screen. [...]

Swipe Quickly move your finger in from the edge of the screen, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps, and so on. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings). Swipe from the top edge: opens or closes the app command bar. For details and m[...]

Swipe Quickly move your finger in from the edge of the Touch Pad, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings). Swipe from the top edge: opens or closes the app command bar. Some of the Touch Pad ope[...]

CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. NUM LOCK When the NUM LOCK indicator glows, you can use the number keys on the keyboard for number entry. Function Key The function keys (F1 ~ F12) are the twelve keys at the top of your keyboard. You can configure the function keys’ mode as "Specia[...]

Special function mode Standard F1- F12 mode Function FN + 1 FN + 1 Reduces the icon size on the desktop or the font sizes within one of the supported application windows. FN + 2 FN + 2 Enlarges the icon size on the desktop or the font sizes within one of the supported application windows. FN + Space FN + Space Changes the display resolution. FN + Z[...]

Remote Controller A remote controller, which is provided with some models, enables you to perform some functions of your computer from a distant location. You can use your remote controller with a media player (such as ArcSoft TV5.0, TOSHIBA VIDEO PLAYER, TOSHIBA Blu-ray Disc Player, etc) to play discs and videos, or to watch and record television [...]

Figure 4-2 Remote controller 5 4 2 3 9 8 12 14 17 16 19 25 22 6 7 1 10 11 13 15 18 20 21 23 24 1. Power 8. Red Button 14. Channel/Page Control 20. Pause 2. Start 9. Green Button 15. Arrows and OK 21. Stop 3. Teletext 10. Yellow Button 16. Mute 22. Volume Control 4. Recorded TV 11. Blue Button 17. Replay 23. Play 5. Guide 12. Back 18. Skip 24. FWD ([...]

Guide Allows you to switch to the Electronic Program Guide (EPG) screen if the ArcSoft TV 5.0 window is active. Live TV Allows you to switch to the Live TV screen if the ArcSoft TV 5.0 window is active. DVD Menu Opens the main menu on a DVD movie, if available. Red, Green, Yellow and Blue buttons It jumps to a registration link.These buttons are no[...]

Volume Control Increases or decreases the volume while watching TV, viewing DVD's or replaying CD's. Play Plays the selected media. FWD (Fast Forward) Moves the media (video, disc, music, and so on) forwards. REW (Rewind) Moves the media (video, disc, music, and so on) backwards. Using the Remote Controller Some computers include a remote[...]

When an obstacle stands between the infrared receiver window of your computer and the Remote Controller. When direct sunlight or strong fluorescent light strikes the infrared receiver window. When the infrared receiver window or the infrared emission part of the Remote Controller is dirty. When other computers which use an infrared remote controlle[...]

Figure 4-4 Pulling the battery tray 1 2 2 1 1. Battery tray lock 2. Battery tray 2. Remove the discharged battery from the battery tray and lay a new one in place. Be sure to place the battery with correct polarities. 3. Push it forward until you hear a click. Figure 4-5 Replacing the battery Optical disc drives The computer may be installed with a[...]

Blu-ray™ Writer drive In addition to the above formats, Blu-ray™ Writer drive supports BD-R, BD- R DL, BD-RE and BD-RE DL. Blu-ray™ Writer drive BDXL™ In addition to the above formats, Blu-ray™ Writer drive BDXL™ supports BD-R TL, BD-R QL and BD-RE TL. Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable. Using optica[...]

3. Lay the disc, label side up, in the disc tray. Figure 4-7 Inserting a disc 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat. Do not touch [...]

When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove di[...]

Blu-ray™ discs BD-R, BD-R DL, BD-R TL and BD-R QL discs can be written only once. The recorded data cannot be erased or changed. BD-RE, BD-RE DL and BD-RE TL discs can be recorded more than once. Writing discs You can use the DVD Super Multi drive or Blu-ray™ Combo drive to write data to either CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD +[...]

problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents. Before writing or rewriting Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that d[...]

DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell, Ltd. (for 3x and 5x speed media) BD-R: Panasonic Corporation BD-R DL: Panasonic Corporation BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: TDK.[...]

Do not perform any of the following actions: Change users in the Operating Systems. Operate the computer for any other function, including such tasks as using a mouse or Touch Pad, or closing/opening the display panel. Start a communication application. Apply impact or vibration to the computer. Install, remove or connect external devices, includin[...]

Do not playback video while watching or recording television programs using other applications. Doing so may cause video playback or television program recording errors. In addition, if prescheduled recording starts during video playback it may cause video playback or television program recording errors. Please view video during times when there is[...]

Display Devices & Audio If the video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution. To change the screen resolution, click Desktop -> Desktop Assist -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution . However, video can[...]

TOSHIBA Blu-ray Disc Player Please be aware of the following limitations when you use TOSHIBA Blu- ray Disc Player. Notes on Use This software can only be used on Windows operating system. Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. Close all other applications before playing back [...]

To playback video on an external display or TV using TOSHIBA Blu- ray Disc Player, use output devices like external displays or TV that have HDCP supported HDMI port. The video cannot be displayed on an external display or TV connected to the RGB connector. The Blu-ray Disc™ movie can be played only on internal LCD displays or external devices co[...]

Screen display and available features may vary amongst Blu-ray™ Videos and scenes. If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used. Open TOSHIBA Blu-ray Disc Player Manual TOSHIBA Blu-ray Disc Player features and instructions are exp[...]

Notes on 3D Playback for TOSHIBA VIDEO PLAYER TOSHIBA VIDEO PLAYER has 3D playback function, which can playback 3D video content, and 2D home video content (DVD or video file) in 3D using real-time 2Dto3D conversion. Effect of 3D can be shown only on an external 3D devices connected via an HDMI output. It cannot be shown on the internal display. Th[...]

In order for 3D playback to work on external display/TV, you need a 3D enabled display/TV that has an HDCP compliant HDMI port. 3D video content can only be displayed on external display using HDMI "with 3D". The 3D effect differs among individuals. Viewing 3D playback may cause discomfort. In this case, please stop viewing and consult yo[...]

The Player is intended for playing DVD-Video, DVD-VR and video files and for viewing 2D home video content and other 2D content created by you in 3D. The 3D playback of any video content not created by the user may require the direct or indirect permission of third parties, where such content is protected by copyright, unless otherwise permitted un[...]

Please consider whether it is suitable or is there a need for limiting the viewing time before allowing your child to watch a 3D content. This software does not have parental lock for 3D video viewing. Please use the login-password functions of Windows if you are worried about the effect of 3D playback on your child's visual function. This sof[...]

Connecting the Cable This section describes how to connect the coaxial cable to your computer. Connecting the coaxial cable When lightning occurs, do not touch the antenna line. This may cause an electric shock. If you have to operate your computer during a thunderstorm and are connecting the TV tuner to an outside antenna, you should operate your [...]

Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off. If the RTC battery becomes completely discharged, the system will lose this information and the real time clock and calendar will stop wor[...]

Battery type Power off Power on Battery pack (48Wh, 6 cell) 3 hours max 3 hours Battery pack (47Wh, 8 cell) 2.5 hours max 2.5 hours Please be aware that the charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you are using the computer - if you make heavy use of external devices for exam[...]

You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. This is because the computer needs this time to check the battery's remaining capacity and then calculate the remaining operating time, based on this together with the current power consumption. Please be aware that the actu[...]

Battery type Sleep Mode Shut Down Mode Battery pack (47Wh, 8 cell) about 3 days about 44 days Extending battery life To maximize the life of your battery packs: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed bel[...]

In Hibernation Mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed. Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries. Removing the battery pack To remove a [...]

Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries. 1. Insert the battery pack as far as it will go into the computer. 2. Ensure that the battery pack is securely in place and the battery lock is in its locked position.[...]

Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. Do not connect any other cable to the LAN jack except the [...]

Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. a. The computer is turned on. b. The computer was shut down in either Sleep or Hibernation Mode. c. Wake-up on LAN is enabled. d. The wireless communication function is on. e. Sleep and Charge function is enabled. Be careful [...]

6. Slide your fingernail or a thin object under the cover and lift it off. Figure 4-13 Removing the memory module cover 1 2 1. Screw 2. Memory module cover Product appearance depends on the model you purchased. User's Manual 4-37[...]

7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 4-14 Seating the memory module 2 1 1. Notch Product appearance depends on the model you purchased. Never allow metal objects, such [...]

8. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-15 Seating the memory module cover 2 1 1. Memory module cover 2. Screw Product appearance depends on the model you purchased. 9. Install the battery pack - refer to Replacing the battery pack section, if[...]

8. Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. Do not touch the connectors on t[...]

Please note that an adaptor is required to use miniSD/microSD Card. Please note that not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly. Figure 4-17 Examples of memory media Secure Digital (SD) Card microSD card adaptor and microSD card MultiMe[...]

Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows. Should you need to format all areas of t[...]

Inserting memory media The following instructions apply to all types of supported media devices. To insert memory media, follow the steps as detailed below: 1. Turn the memory media so that the contacts (metal areas) face down. 2. Insert the memory media into the memory media slot on the front of the computer. 3. Press the memory media gently until[...]

Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data in the memory media could be lost. Do not remove only the miniSD/microSD Card while leaving the adaptor in the memory media slot. External Display Your computer video capabilities can be enhanced with additional displays. Ex[...]

At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio. The HDMI out port HDMI (High-Definition Multimedia Interface) port digitally transfers both video and audio data without reducing the quality. HDMI-compatible extern[...]

1. Click Desktop -> Desktop Assist -> Control Panel -> Hardware and Sound -> Sound . 2. In the Playback tab, select the playback device which you want to switch to. 3. To use the internal speakers on your computer, select Speakers . To use the television or the external monitor that you have connected to the computer, select a different[...]

Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its right side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for atta[...]

Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows. To launch the Volume Mixer utility, click Desktop and right click on the speaker icon on the Taskbar, and then select Open Volume Mixer from the sub menu. To adjust the volume level of speakers or headphones, move the Spea[...]

Bass enhancement for rich, low frequency production High frequency definition for crisp details Consistent volume level across content To access the utility, Click Desktop -> Desktop Assist -> Media & Entertainment -> DTS Studio Sound . U.S. patents apply to this product. See http://patents.dts.com. Manufactured under license from DTS [...]

Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refe[...]

TOSHIBA Display Utility TOSHIBA Display Utility includes Desktop Text Size utility, Split Screen utility and Resolution+ settings. Desktop Text Size allows you to make the text size bigger or smaller on the desktop according to your usage and favorite. You can change the text size on the display and on the title bar of windows by changing the scali[...]

TOSHIBA HDD Accelerator TOSHIBA HDD Accelerator is a utility that can improve hard drive access performance by using part of the main memory of the computer as a cache. To access this utility, click Desktop -> Desktop Assist -> Tools & Utilities -> System Settings - > HDD Accelerator . TOSHIBA VIDEO PLAYER This software is provided [...]

TOSHIBA Media Player by sMedio TrueLink+ This software is a multimedia player which can be used to play back video, music and photo. TOSHIBA Media Player can play back contents on a local library/home network/SkyDrive. To access it, click the Media Player icon on the Start screen. For details, please refer to the Online help. CyberLink MediaShow 6 [...]

TOSHIBA Service Station This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accor[...]

AirGet for TOSHIBA This software is provided for remote access to photos and documents in your computer from mobile devices. This computer is used as a home server. The client application should be installed in the mobile device. To access this software, click AirGet for TOSHIBA in the Apps view. For details on how to use AirGet, see the help file.[...]

System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Power on password Two levels of password security, supervisor and user, are available to prevent unauthoriz[...]

USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports. For example, if a mouse or USB keyboard is connected to a USB port, clicking the mouse button or pressing the keyboard will wakeup the computer. Heat dispersal *1 To protect against overheating, the processor is equi[...]

After you set the password, a dialog box will be displayed asking whether you want to save it to other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place. When entering the character string to register the password, enter from the keyboard character by character and do no[...]

When saving the HDD User Password shut down or restart the computer. If the computer is not shut down or restarted, the saved data may not be correctly reflected. For more information on shutting down or restarting the computer, refer to Turning on the power . Supervisor Password If you set a Supervisor Password, some functions might be restricted [...]

To run TOSHIBA System Settings, click Desktop -> Desktop Assist -> Tools & Utilities -> System Settings . The TOSHIBA System Settings window contains a number of tabs to allow specific functions of the computer to be configured. In addition there are also three buttons: OK, Cancel and Apply. OK Accepts your changes and closes the TOSHI[...]

USB Sleep and Charge You can use the Sleep and Charge function to charge certain USB- compatible external devices such as mobile phones or portable digital music players. Your computer can supply USB bus power (DC5V) to the compatible port even when the computer is turned OFF. "Power OFF" includes Sleep Mode, Hibernation Mode or shutdown [...]

Your PC has multiple charging modes so that many different USB devices can be supported for Sleep and Charge function. Auto Mode (Default) is suitable for a wide range of digital audio players. While using Auto Mode , your computer can supply USB bus power at maximum 2.0A to the compatible ports while the computer is turned off. When USB device can[...]

The "System ON CDP Charge Mode" may not work with certain external devices even if they are compliant with the USB specifications. In those cases, use a USB port without "USB Sleep and Charge function" or disable “System ON CDP Charge Mode”. It is recommended that AC adaptor be connected to the computer while supplying USB b[...]

Use the Sleep and Music function with the display open. Function under Battery Mode This option can be used to enable/disable Sleep and Music under battery mode. It also displays the remaining battery capacity. Move the slider to enable or disable this function. Enabled Enables Sleep and Music function under battery mode. Disabled Enables Sleep and[...]

Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. The above problems could be remedied by turning Resolution+ off. Tap/click the Refresh button on app commands to refresh the content displayed on Library Screen. It won’t be refreshed automatically. If sleep, hibernation, shutdown or re[...]

8. Select a template from Step 3: Select menu template . 9. Setup the advanced video & audio properties by clicking Advanced button on the top. 10. Start burning your movie disc by clicking Burn button. How to learn more Please refer to the Help and Manual files for additional information about CyberLink MediaShow by pressing F1 after the appli[...]

Do not perform any of the following actions: Operate the computer for any other function, including using a mouse or Touch Pad, or closing/opening the display panel. Bump or cause vibration to the computer. Use the Mode control button and Audio/Video control button to reproduce music or voice. Force eject the optical drive when burning. Install, re[...]

may also be used to help diagnose problems should the computer require service by TOSHIBA or TOSHIBA's authorized service providers. Additionally, TOSHIBA may also use this information for quality assurance analysis. Subject to the use restrictions above, the data on the internal storage drive logged may be transferred to entities located outs[...]

The following error message may appear when Internet cannot be accessed at the launch of AirGet on your mobile device: "AirGet could not connect to the server. Please check your connection and try again." Video playback may restart from the beginning if your mobile device resumes from sleep mode. The quality of video and music streaming w[...]

7. After pairing is completed, click Test to test Remote Wake up and then click Done to go to the main menu. You can also skip the Remote Wake up test by clicking Skip . Using AirGet for TOSHIBA AirGet for TOSHIBA enables you to access files stored in your computer from mobile device. If the computer and mobile device are connected to the same netw[...]

The software cannot work when the computer enters screen saver. The software doesn’t support external camera. The software doesn’t support multiuser account operation. The software cannot work under a guest account. The software may not work properly when the camera is facing strong light or the computer is placed in dark environment. Small han[...]

You can use your hand with simple gestures below to control computer. Swipe left Stretch your hand, and quickly move to the left without pausing. Function: Opens the Start screen or, if already on the Start screen, returns you to your last app. This is equivalent to pressing Windows ® logo key. Swipe right Stretch your hand, and quickly move to th[...]

Zoom Raise your fist, move close to the screen to zoom in or move away to zoom out. Stretch your hand to end the operation. Function: Zoom in or out. The zoom gesture is supported by the following applications: Photos app, Internet Explorer app, Maps app from the Start screen Microsoft Windows Photo Viewer from Desktop . The software should be disa[...]

and automatically moves the Hard Disk Drive head to a safe position to reduce the risk of damage that could be caused by head-to-disk contact. HDD Protection function does not guarantee that the hard disk drive will not be damaged. During audio/video playback, when the computer detects a shock or vibration and the hard disk drive's head is par[...]

OFF TOSHIBA HDD Protection is disabled. Detection Level There are four sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF, 1, 2 and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used in a mobile environment or in other unstable co[...]

Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer. System Recovery There is a hidden partition allocated on the Hard Disk Drive for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system. The following items will be described in this sec[...]

The application will allow you to choose from a variety of different media onto which the recovery image can be copied including disc media and USB Flash Memory. Please note that some of the disc media may not be compatible with the optical disc drive connected to your computer. You should therefore verify the optical disc drive supports the blank [...]

1. Load the Recovery Media into the Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port. 2. In the Settings charm, click Power and then select Restart . 3. Hold down the F12 key and then release this key one second after the computer is power on. 4. Use the up and down cursor key to select the appropriate option f[...]

4. Select Reset your PC . 5. Follow the on screen instructions to finish the recovery. You can also perform the restoration through PC settings in the operating system: 1. Click the Settings charm and click Change PC settings . 2. Click Update and recovery under PC settings and then click Recovery . 3. Click Get started under Remove everything and [...]

Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place. Problem so[...]

Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this[...]

Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripheral[...]

If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator. If the indicator is glowing, the computer is connected to a live external power source. The computer wi[...]

Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shut down to prevent any damage - in this instance all unsaved data in memory will be lost. Problem Procedure Computer shuts down automatically. Leave the computer off until the it reaches room temperatu[...]

Problem Procedure Battery doesn’t charge when the AC adaptor is attached. If the battery is completely discharged, it will not begin charging immediately, in these instances you should wait a few minutes before trying again. If the battery still does not charge, you should check that the power outlet the AC adaptor is connected to its supplying p[...]

Real Time Clock Problem Procedure The BIOS setting and system date/ time are lost. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the BIOS setup application by using the following steps: 1. In the Settings charm, click Power and then select Restart . 2. Hold down the F2 key and then release t[...]

Problem Procedure Markings appear on the computer's display panel. These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed. You should try to remove the marks by gently wiping the display panel with a clean dry cloth or, if this fails, with a good quality LCD screen cleaner. In this latter[...]

Problem Procedure You cannot access a CD/DVD/Blu-ray Disc™ in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the[...]

Problem Procedure On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Double-tapping (Touch Pad) does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. To acce[...]

Problem Procedure Double-clicking does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. To access this utility, click Desktop -> Desktop Assist -> Control Panel -> Hardware and Sound -> Mouse . 2. Within the Mouse Properties window, click the Buttons tab. 3.[...]

Sleep and Charge function For more information and settings, please refer to the USB Sleep and Charge section. Problem Procedure I cannot use the Sleep and Charge function. Sleep and Charge function may be disabled. Enable the Sleep and Charge function in the TOSHIBA System Settings. When there is a current overflow of the external device connected[...]

Problem Procedure The "USB Wakeup function" does not work. When Sleep and Charge function is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function. In that case, use an USB port that does not have the USB Sleep and Charge function or change to disable Sleep and Charge function. Sou[...]

Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press the function [...]

Problem Procedure Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator. Wireless LAN Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on. If problems [...]

If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance. Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for curre[...]

Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. P70-A Approximately 418.4 (w) x 272.5 (d) x 28/33.7 (h) millimeters (no[...]

Power Requirements AC adaptor 100-240V AC 50 or 60 Hz (cycles per second) Computer 19V DC External RGB monitor port pin assignment 6 10 1 5 15 1 1 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 +5V Power Supply 10[...]

the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.75 mm 2 Current rating: Minimum 2.5 amperes Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 Australia: AS Japan: DENANHO Europe: Austria: OVE Italy: IMQ Belgium: CEBEC The Nether[...]

Australia AS approved Europe Approved by the appropriate agency Canada CSA approved China CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is complian[...]

Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitte[...]

Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury. It may not be possible to make a network connection to a specified network name using the ad hoc network functi[...]

The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to "obstacles" [...]

Radio Regulatory Information The Wireless device must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This product complies with the following radio frequency and safety standards. Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Euro[...]

Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. 2. Permitted to use for public wireless access lo[...]

check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS-210 of the Industry Canada Rules. Operation [...]

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca Taiwan Article 12 Without permission granted by the NCC, any company, enterprise, [...]

3. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations. 2. Indication for Wireless LAN The indication shown below appears on this equipment. (1) (2) (3)(4) (5) 1. 2.4 : This equipment uses a frequency of 2.4GHz. 2. DS : This equipment uses DS-SS modulation. 3. OF : Thi[...]

Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law of Japan. Atheros QCWB335 Wireless Network Adapter b/g/n(b/g) and Bluetooth The Name of the radio equi[...]

Legal Footnotes Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing U[...]

Memory (Main System) Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities. The amount of main system memory allocated to support graphics may vary depending on the graphics system, applications utilized, system memory[...]

LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. Screen will dim when the computer is operated on battery power and you may not be able to increase the [...]

bps: bits per second CD: Compact Disc CD-ROM: Compact Disc Read-only Memory CD-RW: Compact Disc-rewritable CMOS: Complementary Metal-oxide Semiconductor CPU: Central Processing Unit DC: Direct Current DDR: Double Data Rate DIMM: Dual Inline Memory Module DVD: Digital Versatile Disc DVD-R: Digital Versatile Disc-recordable DVD-RAM: Digital Versatile[...]

LED: Light Emitting Diode MB: megabyte MBps: megabytes per second MMC: Multi Media Card OCR: Optical Character Recognition (Reader) PC: Personal Computer PCI: Peripheral Component Interconnect PCMCIA: Personal Computer Memory Card International Association RAM: Random Access Memory RGB: Red, Green, and Blue RFI: Radio Frequency Interference ROM: Re[...]

Index A AC adaptor additional 4-47 connecting 2-3 DC IN 19V jack 3-6 ASCII characters 4-5 B Battery extending life 4-32 monitoring capacity 4-30 real time clock 3-13, 4-29 save mode 5-7 types 4-28 Battery indicator Battery pack replacing 4-32 Bluetooth 7-7 C Cleaning the computer 1-13 Cooling vents 3-6, 3-8 D DC IN indicator 3-2 DC IN/Battery indic[...]

L LAN cable types 4-34 connecting 4- 35 M Media care Card care 4-42 Memory card care 4-42 Memory installing 4-36 removing 4-39 memory media card inserting 4-43 removing 4-43 Memory media slot 4-40 Moving the computer 1-14 MultiMediaCard removing 4-43 P Password power on 5-7 Starting the computer by password 5-10 Supervisor 5-10 user 5-8 Pointing De[...]

setting 2-10 System automatic 5-7 Sound system problems 6-13 T TOSHIBA Desktop Assist 5-1 Touch Screen U USB device problems 6-11 V Video mode 4-49 Video RAM 3-13 W Web Camera 3-10 Wireless communication 7-5 User's Manual Index- 3[...]