Toshiba R200 инструкция обслуживания

1 Toshiba Personal Computer PORTEGE R200 Maintenance Manual TOSHIBA CORPORATION File Number 960-519 [CONFIDENTIAL][...]

ii [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Copyright © 2005 by Toshiba Corporation. All rights reserve d. Under the copyright laws, this manual cannot be reproduced in any form without the prio r written permission of Toshiba. No patent liability is assumed with respec t to the use of the information contained herein. Toshiba P[...]

PORTEGE R200 Maintenance Man ual (960-519) [CONFIDENTIAL] iii Preface This maintenance manual describes how to pe rform hardware service maintenance for the Toshiba Personal Computer PORTEGE R200, refe rred to as PORTEGE R 200 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Repla[...]

iv [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the PORTEGE R200 system unit and each FRU. Chapter 2 Troubleshooting Procedures e xplains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diag[...]

PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] v Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronym s are enclosed in parentheses following their definition. For example: Read Only Memor[...]

vi [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ... 1-1 1.2 1.8-inch Hard Disk Drive ...........................................................................[...]

PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-4 3.3 [...]

viii [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Chapter 4 Replacement Procedures 4.1 Overview .............................................................................................................. 4-1 4.2 Battery pack ......................................................................................................... 4[...]

PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] ix Appendices Appendix A Handling the LCD Module ........................................................................ A-1 Appendix B Board Layout ............................................................................................. B-1 Appendix C Pin Assignment ................[...]

x [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519)[...]

[CONFIDENTIAL] Chapter 1 Hardware Overview[...]

1 Hardware Overview 1-ii [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 1 Hardware Overview[...]

1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features ................................................................................................................... ... 1-1 1.2 1.8-inch Hard Disk Drive ................................................................................[...]

1 Hardware Overview 1-iv [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Figures Figure 1-1 Front of the computer..................................................................................... 1-4 Figure 1-2 System unit configuration .............................................................................. 1-5 Figure 1-3 Syst[...]

1.1 Features 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-1 1 Features 1.1 Features The PORTEGE R200 is an ultra thin and lightwe ight PC realizing cable-less environment on a table by wireless function with an Intel Mobile Pentium -M pro cessor realizing high performance. Microprocessor Intel Mobile Pentium-M A [...]

1 Hardware Overview 1.1 Features 1-2 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Display LCD Built-in 12.1 inch, 16M colors, XGA (1024 × 768 dots), thin type low temperature poly- silicon TFT color display. Video contro ller is included in North Bridge chip. External monitor Supported via an RGB connector Keyboard Keyboard has 84(U[...]

1.1 Features 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-3 Built-in Modem The internal modem is equipped as a modem daughter card (MDC). The internal modem provides capability fo r data and fax communication and supports ITU-T V.90 (V.92) standard. For data recep tion it operates at 56Kbps and for data transmiss[...]

1 Hardware Overview 1.1 Features Figure 1-1 shows the front of the computer and Figure 1-2 shows the system units configuration. Figure 1-1 Front of the computer 1-4 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519)[...]

1.1 Features 1 Hardware Overview Figure 1-2 System units configuration PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-5[...]

1 Hardware Overview 1.1 Features Figure 1-3 shows the system block diagram. Figure 1-3 System Block Diagram 1-6 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519)[...]

1.1 Features 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-7 The PC contains the following components. CPU • A 1.2GHz Intel Mobile Pentium-M pro cessor with a 400MHz external clock, 100MHz bus and 0.94/0.81V core opera tion voltage (built-in NDP). • Internal cache memory: 32KB Data and 32KB Instruction, Write-[...]

1 Hardware Overview 1.1 Features 1-8 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) PCI chipset This gate array incorporates the following elem ents and functions. • North Bridge (Intel-made 915GMS Express) – Dothan Processor System Bus support – System memory interface – DDR2 memory channel support – DMI (Direct Media Interf[...]

1.1 Features 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-9 PC card controller (Texas Instruments-made PCI7411) • • • • • • • PCI interface (PCI Revision2.2) CardBus/PC Card controller (Yenta2 Version2.2) SD/MMC card controller (SDHC Ver.1.2) SD IO card controller (Ver.1.1) Memory Stick/Memory Stick[...]

1 Hardware Overview 1.2 1.8-inch Hard Disk Drive 1.2 1.8-inch Hard Disk Drive A compact, high-capacity HDD with a height of 5.0/8.0mm. Contains a 1.8-inch magnetic disk and magnetic heads. Figure 1-4 shows a view of the 1.8-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-4 1.8-inch HDD Table 1-1 1.8-inch HDD dimensions Standard va[...]

1.2 1.8-inch Hard Disk Drive 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-11 Table 1-2 1.8-inch HDD Specifications Specification Parameter TOSHIBA HDD1442BZ L01 TOSHIBA HDD1544BZ K01 Storage size (formatted) 30GB 60GB Speed (RPM) 4,200 Data transfer speed (Mbits/s) 131.1 to 283.3 Interface transfer rate (Mbytes/s[...]

1 Hardware Overview 1.3 Keyboard 1-12 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 1.3 Keyboard The keyboard is mounted 84(US)/85(UK) keys th at consist of character key and control key. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. See Appendix E about a layout of the [...]

1.4 TFT Color Display 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-13 1.4 TFT Color Display The TFT color display consists of a LCD module and FL inverter board. 1.4.1 LCD Module The LCD module used for the TFT color display us es a backlight as the light source and can display images and characters of 16M colors[...]

1 Hardware Overview 1.4 TFT Color Display 1-14 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 1.4.2 FL Inverter Board The FL inverter board supplies a high freque ncy current to illuminate the LCD module FL. Table 1-4 lists the FL inve rter board specifications. Table 1-4 FL inverter board specifications Specifications Item G71C0002K21[...]

1.5 Power Supply 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-15 1.5 Power Supply The power supply supplies twenty-three di fferent voltages to the system board. The power supply microcontroller has the following functions. 1. Judges that the DC power supply (AC ad apter) is connected to the computer. 2. Detects [...]

1 Hardware Overview 1.5 Power Supply 1-16 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Table 1-5 lists the power supply output specifications. Table 1-5 Power supply output specifications Name Voltage (V) Use PPV 0.940 - 0.81 CPU (ULV) PTV 1.05 CPU, GMCH, ICH6-M 1R5-P1V 1.5 CPU, GMCH, ICH6-M 1R5-E1V 1.5 ICH6-M 1R8-B1V 1.8 GMCH, DDR2-[...]

1.6 Batteries 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-17 1.6 Batteries The PC has the following three batte ries. Main battery Secondary battery (option) Real time clock (RTC) battery Table 1-6 lists the specifications for these two batteries. Table 1-6 Battery specifications Battery name Material Output vol[...]

1 Hardware Overview 1.6 Batteries 1-18 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 1.6.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and dete cts a full charge when the AC adaptor and battery are connected to the co mputer. The system[...]

1.7 AC Adapter 1 Hardware Overview PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 1-19 1.7 AC Adapter The AC adapter is also used to charge the battery. Table 1-9 lists the AC adapter specifications. Table 1-9 AC adapter specifications Parameter Specification G71C0001A310 G71 C0001A410 G71 C0004A210 Power 45W 60W Input voltage 100V to 2[...]

1 Hardware Overview 1.7 AC Adapter 1-20 [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519)[...]

[CONFIDENTIAL] Chapter 2 Troubleshooting[...]

2 Troubleshooting 2-ii [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 2[...]

2 Troubleshooting PORTEGE R200 Maintenance Man ual (960-519) [CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ........................................................................................ [...]

2 Troubleshooting 2-iv [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) 2.8 Display Troubleshooting .......................................................................................... 2-39 Procedure 1 External Monitor Check ....................................................... 2-39 Procedure 2 Diagnostic Test Program Execution C[...]

2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-v 2.16 Fingerprint sensor .................................................................................................... 2-5 6 Procedure 1 Setting Windows Log-ON password ................................... 2-57 Procedure 2 Registratio n of fingerprint.............[...]

2 Troubleshooting 2-vi [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519)[...]

2.1 Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-1 2 2.1 Troubleshooting Chapter 2 describes how to determine which Fi eld Replaceable Unit (FRU) in the computer is causing the computer to malfunction. (The “FRU ” m eans the replaceable unit in the field.) The FRUs covered are: 1. Power supply [...]

2 Troubleshooting 2.2 Troubleshooting Flowchart 2-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-519) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determ ining which FRU malfunctions. Before going through the flowchart steps, check the following:  Ask user to enter the password if a password is registered[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Figure 2-1 Troubleshooting flowchart (1/2) PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-3[...]

2 Troubleshooting 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (2/2) 2-4 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-519)[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-5 If the diagnostics program cannot detect an e rror, the problem may be intermittent. The Test program should be executed several tim es to is olate the problem. Check the Log Utilities function to confirm which diagnos tic test detected a[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-6 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-519) 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 1 Power supply icon Check The following two icons indicate the power supply status:  Battery icon  DC IN icon The power supply controller uses the power supply status with the Battery icon and the DC IN icon as listed in the tables below. Table 2-1 Battery icon Battery icon Power su[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-8 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-519) When icons are blinking, perform the following procedure. 1. Remove the battery pack and the AC adap ter and cut off the power supply to the computer by force. 2. Re-attach the battery pac k and the AC adapter. If icons are still blinki[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” On for one second “0” On for half second Interval between data bi[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-10 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Check 1 Convert the DC IN icon blink patt ern into the hexadecimal error code and compare it to the tables below. Then go to Check 2. Table 2-3 Error code Error code Where Error occurs 1*h DC Power (AC Adapte r) 2*h Main battery 3*h S[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-11  Main Battery Error code Meaning 22h Main battery discharge current is ove r 0.5A. 23h Main battery charge current is over 2.7 A . 24h Abnormal current has been sensed 0[A]. 25h Main battery charge current is over 0.3 A .  Secon[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting 2-12 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9)  E3V output Error code Meaning 60h E3V voltage is over 3.96V when the computer is powered on/off. 61h E3V voltage is under 2.81V when the compute r is powered on. 62h E3V voltage is under 2.81V when the compute r is booting up. 63h[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-13  PTV output Error code Meaning A0h PTV voltage is over 1.26V when the computer is powered on/off. A1h PTV voltage is under 0.89V when the compute r is powered on. A2h PTV voltage is under 0.89V when the compute r is booting up. A3h[...]

2 Troubleshooting 2.3 Power Supply Troubleshooting Procedure 3 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconn ected. Perform starting from Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If these cabl[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-15 Procedure 4 Charge Check Check if the power supply cont roller charges the battery pack properly. Perform the following procedures: Check 1 Make sure the AC adapter is fi rmly plugged into the DC IN socket. Check 2 Make sure the batte[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-16 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) 2.4 System board Troubleshooting This section describes how to determ ine if the Sy stem board is defective. Start with Procedure 1 and continue with the other pr ocedures as instructed. The procedures described in this section are: P[...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-17 Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the System board and initializes it.  If an error message is shown [...]

2 Troubleshooting 2.4 System board Troubleshooting 2-18 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Check 3 The IRT checks the System board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (22) or (23) is displayed, go to Procedure 5. If error mes[...]

2.4 System board Troubleshooting 2 Troubleshooting Procedure 2 Debug Port Check Check the D port status by a debug port test. Th e tool for debug port test is shown below. Figure 2-2 A set of to ol for debug port test The test procedures are follows: 1. Connect the debug test cable to the c onnector CN3400 of the system board. For disassembling to [...]

2 Troubleshooting 2.4 System board Troubleshooting 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting D port into FDD and input “FD starting drive:>dport”.) The D port status is displayed in the following form; F100 : 000.000382 IRT_CHK_INISYSI_START D port status Time (second) to process Contents of proc[...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-21 Table 2-4 D port status (1/8) D port Status Test item Message Permission of A20 line and Clearanc e of software reset Prohibition of APIC Initialization for MCH Initialization for ICH Initialization for Super I/O Initialization for De[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-22 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Table 2-4 D port status (2/8) D port Status Test item Message FAN control Sound controller init ializati on (for beep) Enabling system speaker Releasing mute Sets the volume maximum. (models that can control volume) BIOS, EC/KBC rewri[...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-23 Table 2-4 D port status (3/8) D port Status Test item Message Check of DRAM type and size Check of DRAM type and size (in Cold bo ot) When not-supported memory is connected, HLT after beeping. F101H SM-RAM stack area test HLT when DRA[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-24 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Table 2-4 D port status (4/8) D port Status Test item Message Initialization of SMRAM Check of Wake Up factor Rewriting of SMRAM base and storing CPU state map for BIOS F105H Permission only SMI by ASMI Initialization of devices wh ic[...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-25 Table 2-4 D port status (5/8) LED Status Test item Message Initialization of a device that n eeds initialization before PCI bus initialization Setting of AC’97 Initialization of tem perature control information KBC initialization VG[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-26 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Table 2-4 D port status (6/8) LED Status Test item Message Running a task waiting for the end of PCI_CONFIGURATION Initialization of H/W that is necessary after PCI configuration Setting of printer por t (model supp orting PRT) Initia[...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-27 Table 2-4 D port status (7/8) LED Status Test item Message BOOT_PASSWORD (Password check) Waiting for completion of FDD initializatio n ( model with Internal FDD) (Reboot) Waiting for completion of HDD initialization Check of key inpu[...]

2 Troubleshooting 2.4 System board Troubleshooting 2-28 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Table 2-4 D port status (8/8) LED Status Test item Message HW initialization prior to boot, Waiting for the completion of HW initialization Notifies the DVI connection status to VGA BIOS (DVI supporting model) Setting of battery save [...]

2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] 2-29 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the System board and I/O unit. Refer to Chapter 3, Tests and Diagnostic, for more information on how to p[...]

2 Troubleshooting 2.5 USB FDD Troubleshooting 2-30 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) 2 2.5 USB FDD Troubleshooting This section describes how to determine if the USB FDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required. Procedure 1: FDD Head C[...]

2.5 USB FDD Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-31 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD of the computer, turn on the com puter and run the test. Refer to Chapter 3, Tests and Diagnostics, for m ore information about the diagnostics t[...]

2 Troubleshooting 2.5 USB FDD Troubleshooting Procedure 3 Connector Check and Replacement Check The USB FDD connector may be disconnected fr om the system board. Check visually that the connector is connected firmly. Check 1 Make sure the USB cable of the FDD is securely connected to the USB port. USB FDD System board CN4610 CN4611 Make sure USB FD[...]

2.6 1.8” HDD Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-33 2.6 1.8” HDD Troubleshooting This section describes how to determine if the 1.8” HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other procedures as required. Procedure 1: Parti[...]

2 Troubleshooting 2.6 1.8” HDD Troubleshooting 2-34 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the tes t detects an error, an e rror message is disp layed on the screen. Make sure of no f[...]

2.6 1.8” HDD Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-35 Procedure 3 Format Check The computer’s 1.8” HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To format the 1.8" HDD, start with Check 1 below and perform the other steps as re[...]

2 Troubleshooting 2.6 1.8” HDD Troubleshooting 2-36 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about[...]

2.6 1.8” HDD Troubleshooting 2 Troubleshooting Procedure 5 Connector Check an d Replacement Check HDD is connected to the system board via HD FPC. The connection of HDD, HD FPC or system board may be defective. Otherwise, th ey may be faulty. Disassemble the computer following instructions in Chapter 4, Replacement Procedures and perform the foll[...]

2 Troubleshooting 2.7 Keyboard Troubleshooting 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replaceme[...]

2.8 Display Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-39 2.8 Display Troubleshooting This section describes how to determ ine if th e computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Monitor Check Proc[...]

2 Troubleshooting 2.8 Display Troubleshooting Procedure 3 Connector and Cable Check LCD module is connected to system board via the LCD cable. FL inverter is connected to system board via FL cable. The connections of FL inverter is consist of F L cable and HV cable. Fluorescent lamp is connected to FL inverter by HV cable. These cables may be disco[...]

2.8 Display Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-41 Procedure 4 Replacement Check Fluorescent lamp, FL inverter , LCD module, HV cable, FL cable and LCD cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instruction[...]

2 Troubleshooting 2.9 Touch Pad 2.9 Touch Pad To determine whether the Touch Pad is faulty or not, perform the following procedures: Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Cable Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the keyboard test program, [...]

2.10 Modem 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-43 2.10 Modem To check if the modem is defective or malf unctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test[...]

2 Troubleshooting 2.10 Modem Procedure 2 Connector Check and Replacement Check The MDC is connected to the MP FPC and MP FPC is connected to the system board. If the modem malfunctions, these connections may be bad or the MDC, MP FPC or system board might be faulty. Disassemble the computer following the step s described in Chapter 4 and perform th[...]

2.11 LAN 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-45 2.11 LAN To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnost[...]

2 Troubleshooting 2.11 LAN Procedure 2 Connector Check and Replacement Check The LAN function is installed on the system board. The LAN jack is conn ected to the system board by the cable. If the LAN malfunctions, the connection is bad or the system board might be faulty. Disassemble the computer following the step s described in Chapter 4 and perf[...]

2.12 Sound 2 Troubleshooting 2.12 Sound To check if the sound function is defectiv e or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute the Sound tes[...]

2 Troubleshooting 2.12 Sound 2-48 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) Procedure 3 Replacement Check • If headphone does not work properly, perform check 1. • If internal microphone does not work properly, perform check 2. • If speaker does not work properly, perform check 3. Check 1 Headphone may be faulty. Replace it [...]

2.13 Bluetooth Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-49 2.13 Bluetooth Troubleshooting To check if the Bluetooth is malfunctioning or not, follow the troubl eshooting procedures below as instructed. Procedure 1: Transmittin g-Receiving Check Procedure 2: Antennas' Connection Check Proced[...]

2 Troubleshooting 2.13 Bluetooth Troubleshooting Procedure 2 Antennas' Connection Check The Bluetooth function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure that the wire le[...]

2.13 Bluetooth Troubleshooting 2 Troubleshooting PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 2-51 Procedure 3 Replacement Check Bluetooth module, Bluetooth antenna or system board m ay be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disa ssemble the computer and then perform the following checks: Che[...]

2 Troubleshooting 2.14 Wireless LAN Troubleshooting 2-52 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) 2.14 Wireless LAN Troubleshooting To check if the wireless LAN is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Transmittin g-Receiving Check Procedure 2: Antennas' Connection Check Pro[...]

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Main antenna Sub antenna Wireless LAN card Antenna cable MP FPC System board CN2200 CN9510 CN9500 Any of the connections may be defective. Disassemble the computer following the steps described in[...]

2 Troubleshooting 2.14 Wireless LAN Troubleshooting 2-54 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519) Procedure 3 Replacement Check Check if the wireless LAN antenna, wirele ss LAN card, MP FPC and system board are connected properly. Any of these components may be damaged. Disassemble the computer following the steps described in Ch[...]

2.15 SD card slot 2 Troubleshooting 2.15 SD card slot To check if the SD card slot is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Window s Insert a SD card into the slot. Check if the installed Windows OS recognizes [...]

2 Troubleshooting 2.16 Fingerprint sensor 2.16 Fingerprint sensor CAUTION : To delete the account for confirming the fingerprint operation, it is necessary to log on by the account with the ma nagement authority. If the password has been set to log on, ask the Log-ON password to the user. To check if the Fingerprint sensor work correctly or not, fo[...]

2.16 Fingerprint sensor 2 Troubleshooting Procedure 1 Setting Windows Log-ON password 1. Open [User Account] from [Control Panel]. 2. Select “Create a new acc ount” in [User Account]. 3. Input the name of Account (e.g. “TOSHI BA”) in [Name the new account] and click [NEXT] button. 4. Click “Create Account” button in the (default) condit[...]

2 Troubleshooting 2.16 Fingerprint sensor 3. Input the name of Account (e.g. “TOSHIBA ”), which has been inputted in item 3 in Procedure 1, in the box at the right of [User Name:] on the [Verify Username and Password]. In addition, input the password, which has been inputted in item 7 in Procedure 1, in the box at the right of name (e.g. “pa [...]

2.16 Fingerprint sensor 2 Troubleshooting 5. After displaying [Capture Fingerprint], scan the fingerprint of your right index finger on the finger sensor. When it successes the number at the center of display of display changes to “2”, then scan again. When it successes th e number changes to “3”, again scan (total three times). 6. After di[...]

2 Troubleshooting 2.16 Fingerprint sensor 8. When [Audio and Taskbar Setti ngs] is displayed, click [Next]. 9. When [Congratulations] is displayed, click [Done]. 10. When [OmniPass-Logon New User?] is displayed, click [Yes]. 2-60 [CONFIDENTIAL ] PORTEGE R200 Maintenan ce Manual ( 960-519)[...]

2.16 Fingerprint sensor 2 Troubleshooting 11. Close all applications and power off the computer. Procedure 3 Authentication of fingerprint 1. Turn on the computer and start up the Windows. 2. In the Windows Log-ON window, scan the finger print of your right index finger. Make sure that scanned fingerprint is displayed on the frame of [Logon Authent[...]

2 Troubleshooting 2.16 Fingerprint sensor 4. After starting Windows, Make sure that the nam e of Account (e.g. “TOSHIBA”), which has been inputted in item 3 in Pro cedure 1 at the top of [Start]. 5. Open [User Accounts] from [Control Panel]. Select [Delete an Account] in [Change an Account] and delete the account register ed for fingerprint aut[...]

[CONFIDENTIAL] Chapter 3 Tests and Diagnostics[...]

3 Tests and Diagnostics 3-ii [CONFIDENTIAL] PORTEGE R200 Mainten ance Manual ( 960-519) 3[...]

3 Tests and Diagnostics PORTEGE R200 Maintenance Man ual (960-519) [CONFIDENTIAL] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................................. 3-1 3.1.2 [...]

3 Tests and Diagnostics 3-iv [CONFIDENTIAL] PORTEGE R200 Mainten ance Manual ( 960-519) 3.20 ONLY ONE TEST ................................................................................................... 3-41 3.20.1 Program Description .......................................................................... 3-41 3.20.2 Operations .............[...]

3 Tests and Diagnostics PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 3-v 3.28 Sound Test program ................................................................................................. 3-84 3.28.1 Sound (Standard) test ......................................................................... 3-84 3.28.2 Sound (Legacy) test .[...]

3 Tests and Diagnostics 3-vi [CONFIDENTIAL] PORTEGE R200 Mainten ance Manual ( 960-519) Figure Figure 3-1 Name and positions of each side........................................................................ 3-49 Tables Table 3-1 Subtest names .................................................................................................... 3-1[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. There are Service Program Mod[...]

3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST Other tests are:  Wireless LAN TEST (Wireless LAN TEST disk)  LAN/Modem/Bluetooth/IEEE1394 TEST (LAN/Modem/Bluetooth/IEEE1394 TEST disk)  Sound TEST (Sound TEST disk) You will [...]

3.1 The Diagnostic Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-3 3.1.2 H/W (Hardware) initial information setting tool The H/W initial inform ation setting tool consists of the following programs.  Initial configuration  DMI information save  DMI information recovery  System configuration dis[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive. 2. Release the lock of the power switch and turn on the computer with pressing the F12 [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2.1 Diagnostics menu (T&D) To execute this program, select 1- Repair Main (T&D) in the startup menu, press Enter . The following menu appears. TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 – ONL[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST 3 - KEYBOARD TEST 4 - DISPLAY TEST 5 - FLOPPY DISK [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Select the option you want to execute and press Enter . When you select 1-SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT: XXXXX WRITE DATA : XX[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-8 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Re[...]

3.3 Setting of the hardware configuration 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-9 3.3 Setting of the hardware configuration To execute this program, select 2-Repair initial config set in the startup menu, press Enter and follow the directions on the screen. The H/W initial inform ation setting tool cons[...]

3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) • Setting of the HWSC • Setting of the UUID • Display of the DMI information (including UUID) • Setting of DVD region code (Yes/No) After completion of the above settings, H/W configuration & DMI information ar[...]

3.3 Setting of the hardware configuration 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-11 Subtest 08 System configuration display This subtest displays the information of the system configuration. When the following message appears, confirm the contents and press Enter . Press [Enter] key For more details on t[...]

3 Tests and Diagnostics 3.4 Heatrun Test 3-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.4 Heatrun Test To execute this program, select 3-Repair heatrun (T&D) in the startup menu, press Enter . When selecting the option you want to execute, the message shown below will appear and 01-ROM Checksum of the SYSTEM test will be execut[...]

3.5 Subtest Names 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-13 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quick charge [...]

3 Tests and Diagnostics 3.5 Subtest Names 3-14 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER [Not supported] 01 02 03 Ripple pattern Function Wraparound 7 ASYNC [Not supported] 01 02 03 FIR/SIR Point to point (send) FIR/SIR Point to point (receive) Wraparound [...]

3.6 System Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-15 3.6 System Test To execute the System Test, select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ROM Checksum This subte[...]

3 Tests and Diagnostics 3.6 System Test 3-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest 03 Geyserville If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. Subtest 04 Quick Charge This subtest checks the status for the quick charge. Subtest 05 DMI read This subtest[...]

3.7 Memory Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-17 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional mem ory Th[...]

3 Tests and Diagnostics 3.8 Keyboard Test 3-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed key code d[...]

3.9 Display Test 3 Tests and Diagnostics 3.9 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAh and 55h) to the [...]

3 Tests and Diagnostics 3.9 Display Test Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3 ] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mode 117 1024*768 64K] [Mode 118 1024*768 16M] The di[...]

3.9 Display Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-21 Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH H[...]

3 Tests and Diagnostics 3.10 Floppy Disk Test 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because the contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Ent[...]

3.10 Floppy Disk Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-23 Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop S[...]

3 Tests and Diagnostics 3.11 Printer Test 3.11 Printer Test CAUTION : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wrapar[...]

3.11 Printer Test 3 Tests and Diagnostics Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE : To execute thi[...]

3 Tests and Diagnostics 3.12 Async Test 3-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.12 Async Test CAUTION : Async Test is not supported for this model. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want t[...]

3.13 Hard Disk Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-27 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or 09 is exe[...]

3 Tests and Diagnostics 3.13 Hard Disk Test 3-28 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 4. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press [Enter] . The following message will appear during each subtest. HARD DISK TEST XXXXXXX XXX [...]

3.13 Hard Disk Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-29 Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Tests the data interference in the neighbor track.) Wors[...]

3 Tests and Diagnostics 3.14 Real Timer Test 3-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Real tim[...]

3.14 Real Timer Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-31 Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments, m aking sure the date and time are displayed in the following form at: Current date [...]

3 Tests and Diagnostics 3.15 NDP Test 3-32 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP This test checks the following functions of NDP:  Control word  Status word  Bus  Additio[...]

3.16 Expansion Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-33 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound NOTE: To execute this subtest, the PC card wraparound connector is r[...]

3 Tests and Diagnostics 3.16 Expansion Test 3-34 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest 02 RGB monitor ID NOTE: To execute this subtest, an external monitor with monitor ID function is required. Connect the external monitor to the PC for the test of ID acquisition. The judgment of acquisition is based on the panel data. In[...]

3.17 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-35 3.17 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or A[...]

3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-36 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name Common FF Data[...]

3.18 Error Code and Error Status Names 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-37 Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - RECORD N[...]

3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-38 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA CRC ERRO[...]

3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-39 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight- d[...]

3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status 3-40 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncor[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-41 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. #########################[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 01 Pressed key display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function that causes the key’s d[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 02 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check This test displays the response from the touch pad and touch pad switch. When moving your finger on the touch pad towards the upper left, the <POINTING> displ[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 03 GP Button This subtest checks moving of the front operation panel button. Press the Toshiba Presentation button after the following message appears. Press [Toshiba Presentation button] button Power switch Toshiba Presentation Toshiba Assist Press the Toshiba Assist button after the following mes[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-45 Slide the switch to OFF position. Then, following message appears in the display. KILL SWITCH ON !! Slide the switch to ON position. Then, following message appears in the display. KILL SWITCH OFF !! After Sliding the switch to OFF position, re[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-46 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest 06 Docker Dock/Undock This subtest is executed with slim port replicator installed. Press Enter while pushing the eject button of the slim port replicator after the following message appears. Slide Eject-SW, and press [Enter] Key Press E[...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-47 Subtest 07 LED This subtest checks if each LED lights properly. The following message appears in the display in order. Follow the instructions in the display to execute the test. [HDD Access LED test] Press any key and following message appears[...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-48 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest 08 PC-Card Device Lock This subtest checks the device lock function. This test needs a PC card, not a PC wraparound card. Before this test, inset a PC card. When it passes the test, following message appears. Device Lock TEST OK… When [...]

3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 0A Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2. Prevent the machine from shake or shock. Vertical plane Flat desk Set the [...]

3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-50 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) When this subtest is selected, the following message appears in the display. The heaven surface establishes in the upper direction Press [Enter] key NOTE : Be sure to execute the test with the display panel opened. Set the machine on the flat de[...]

3.21 Head Cleaning 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-51 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selecting test 4 fro[...]

3 Tests and Diagnostics 3.22 Log Utilities 3-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk, or output the data to a printer or the displa[...]

3.22 Log Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED 001 FDD 01 0000 180 00001 00 00 0000 FDD-TIME OUT ER[...]

3 Tests and Diagnostics 3.23 Running Test 3-54 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 06) 3. Display test (subtest 01) 4. Real timer test (subtest 02) 5. H[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-55 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy dis[...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message. [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Select[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-57 3. COPY program (a) When COPY is selected, the following message appears. FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage similar to the one below. [...]

3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-58 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 4. DUMP program (a) When DUMP is selected, the following message appears. DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display will go to[...]

3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-59 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) ? 5. HDD[...]

3 Tests and Diagnostics 3.25 System Configuration 3-60 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 3.25 System Configuration 3.25.1 Function Description NOTE : To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to OFF position and restart the test. Otherwise the [...]

3.25 System Configuration 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-61 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMHz Code = [...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-62 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.26 Wireless LAN Test Program (Atheros) This section describes how to perform the wireless LAN transm itting-receiving test (Askey-Made Atheros). CAUTION: To execute this test, another computer with Atheros wireless LAN ca[...]

3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-63 3.26.1 Setting Responder PC 1. When the responder PC has MB44a/g or MB43 Insert the FD, “MB4x Responder media”, in the FDD and power on the computer. When OS is booted, the test program is started and setting is execut[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-64 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.26.2 Test procedure 1. Boot the DUT PC by the FD, “MB4x/MB5x boot media”. The following message is displayed. ************************************************************ * * * Atheros MB4x/MB5x Maintenance T&D (D[...]

3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-65 2. Change the FD in the FDD to “MB5x DUT media” and input “ h ”, then the test menu is displayed. ************************************************************ * * * Atheros MB5x Maintenance T&D Menu * * * * 1 :[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-66 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.26.3 Contents of Test 1. SKU check of Module This displays the destination information of the wireless LAN module as follows: ********************************************* * * * Module : Atheros MB51H (MoW) * * G-code : G[...]

3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-67 4. Communication test of 11g m ode Communication test of 11g m ode Communication test of 11g m ode (Main Antenna only) This checks the antenna connection in 11g mode and transmitting/receiving functions. The number of pack[...]

3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-68 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2. Error in MAC Address Check Error off ALL FF ****************************************** * Mac Address Check NG * * FFFFFF-FFFFFFh * ****************************************** Error off ALL 00 *****************************[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-69 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/Bluetooth/IEEE1394 test in[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program Subtest01 (i82562 + ICHx) NOTE: (i82562 + ICHx) test is not supported in this model. This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear. [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error co[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear. Testing adapter...hit <ESC> to abort. * External Loopback Test...PASSED Testing completed. * * Loopb[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-72 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.27.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Electric Manufacture Co.Ltd)” for t[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-73 3.27.3 Bluetooth test To execute this test, input 3 and press Enter . NOTE : This model does not support the Bluetooth test. NOTE : Use another computer that can communicate by the Bluetooth as a reference machine to[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-74 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: ---------------------------[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-75 If the target machine has any problem, it displays Error m essage. The following message is displayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCS[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-76 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-6 Error code for Bluetooth test (BD_ADDR) (1/2) Error code M[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-77 Table 3-6 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0x24 LMP[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-78 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) When the NICSPC53EXE test program has not been started, following m essage appears. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Co[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-79 Insert a floppy disk containing the test program into the tester machine and turn on the power. When the Bluetooth test menu is displayed on the tester machine, press T and Enter to select the subtest. The following [...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-80 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) If the DUT machine has any problem or S of the DUT machine is pressed before connection to tester machine, the following message “ INCOMPLETE ” is displayed. -------------------------------------------------------[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-81 Error code Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (1/2) Error code Meaning 0x01 Unknown HCI Command. 0x02 No Connection. 0x03 Hardware Failure. 0x04 Page Timeout. 0x05 Authentication Failure. 0x[...]

3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-82 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision[...]

3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-83 3.27.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. The following menu will ap[...]

3 Tests and Diagnostics 3.28 Sound Test program 3-84 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 Tests and Dia tics 3.28 Sound Test program gnos This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Insert the test program disk for Sound test in the USB FDD and turn on th[...]

3.28 Sound Test program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-85 To return to the Sound test menu, Press 9 and Enter . Then following message will appear in the display. *********************************** ******** May I Restart ? ******* *********************************** Press any key to continue… [...]

3 Tests and Diagnostics 3.28 Sound Test program 3-86 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest02 (Sine Wave) This subtest is executed by loading the COM file (ADSIN.COM). The program expands sine wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to play the [...]

3.28 Sound Test program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-87 3.28.3 CD Sound (Standard) test To execute the CD Sound (Standard) test, press 3 and Enter . Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). Following menu [...]

3 Tests and Diagnostics 3.28 Sound Test program 3-88 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest03 Test Tone A CAUTION: Before starting subtest03, be sure to set the sound at proper volume. This subtest plays sine wave while changing its table from 100Hz to 20Hz. The test returns to the CD Sound (Standard) menu after the test e[...]

3.28 Sound Test program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-89 3.28.3.2 Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT[...]

3 Tests and Diagnostics 3.29 SETUP 3-90 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.29 SETUP 3.29.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory (a) Total 2. System Date/Time (a) Date (MM-DD-YYYY) (b) Time (HH:MM:SS) 3. Battery (a) Battery Save Mode (b) PCI Express Link A[...]

3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-91 11. PCI Bus (a) PCI Bus 12. Security Controller (a) TPM (b) Clear TPM Owner 13. Peripheral (a) Internal Pointing Device 14. Legacy Emulation (a) USB KB/Mouse Legacy Emulation (b) USB-FDD Legacy Emulation (c) USB Memory BIOS Support Type 15. PCI LAN (a)[...]

3 Tests and Diagnostics 3.29 SETUP 3.29.2 Accessing the SETUP Program Select 0-SETUP in the Main Menu and press Enter key. The following display appears. 3-92 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)[...]

3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-93 Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pages. 2. Press either the Sp[...]

3 Tests and Diagnostics 3.29 SETUP SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. (a) Total This field displays the total amount of mem ory installed and is automatically calculated by the computer. You [...]

3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-95 NOTE: Display of the LCD Brightness will be changed in the condition below: (*1) Operating the battery (*2) Using the AC adapter User Setting Use this option to set the battery save parameters on the sub-window, BATTERY SAVE OPTIONS . Processing Speed [...]

3 Tests and Diagnostics 3.29 SETUP 3-96 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) (b) PCI Express Link ASPM This option sets the power saving function of the PCI Express. Auto Saves power consum ption, when the PCI Express device is not used while the battery is working. (Default) Disabled Disables the power saving function and gives[...]

3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-97 (d) Master Password This item sets the Master HDD password. This can be set, only when Master + User is set in the HDD password Mode. For details, refer to the User’s Manual. 6. Boot Priority This tab sets the priority for booting the computer and th[...]

3 Tests and Diagnostics 3.29 SETUP 3-98 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) (b) HDD Priority Set the priority of the HDD as a startup device. Built-in HDD → USB The priority is set as built-in HDD → USB (Default) USB → Built-in HDD The priority is set as USB memory → built-in HDD. 7. Display This group of options config[...]

3.29 SETUP 3 Tests and Diagnostics 8. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Dynamic CPU Frequency Mode Use this option to choose a setting from the followings. Dynamically Switchable CPU power consumption and clock speed automatic switching f[...]

3 Tests and Diagnostics 3.29 SETUP 3-100 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) or BackSpace . Press ↓ to move the cursor to the right and ↑ to move the cursor to the left when you set the date and time. For the Alarm Time , set the time to turn on the power autom atically. The “second” cannot be set. When it is set to “[...]

3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] 3-101 10. Drives I/O This option displays the address and interrupts level for hard disk drive. It is for information only and cannot be changed. Built-in HDD = Primary IDE(1F0H/IRQ14) 11. PCI Bus This item displays the interrupt level for the Card Bus. It [...]

3 Tests and Diagnostics 3.29 SETUP 3-102 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 13. Peripheral Use this option to select the parallel port mode and hard disk mode. (a) Internal Pointing Device This option enables and disables the Touch Pad. Enabled Enables the Touch Pad. (Default) Disabled Disables the Touch Pad. 14. Legacy Em ula[...]

[CONFIDENTIAL] Chapter 4 Replacement Procedures[...]

4 Replacement Procedures 4-ii [CONFIDENTIAL ] PORTEGE R200 Maintenance Man ual (960-519) 4[...]

4 Replacement Procedures PORTEGE R200 Maintenance Man ual (960-519) [CONFIDENTIAL] 4-iii Chapter 4 Contents 4.1 Overview .............................................................................................................. 4-1 4.2 Battery pack .................................................................................................[...]

4 Replacement Procedures 4-iv [CONFIDENTIAL ] PORTEGE R200 Maintenance Man ual (960-519) 4.27 Fluorescent Lamp............................................................................................... 4-54 4.27.1 Replacing the 12.1 inch TMD fluorescent lamp ............................... 4-55 Figures Figure 4-1 Removing the battery pack......[...]

4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [ CONFIDENTIAL] 4-v Figure 4-28 Removing th e internal microphone .......................................................... 4-41 Figure 4-29 Removing the LED FPC .......................................................................... 4-42 Figure 4-30 Removing the display mask [...]

4 Replacement Procedures 4-vi [CONFIDENTIAL ] PORTEGE R200 Maintenance Man ual (960-519)[...]

4.1 Overview 4 Replacement Procedures 4 4.1 Overview This chapter describes the procedure for rem oving and replacing the fi eld replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particular FRU can be removed. [...]

4 Replacement Procedures 4.1 Overview 4-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance Man ual (960-519) Safety precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1) Always use the genuine battery that is authorized by Toshiba or compatib[...]

4.1 Overview 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-3 Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2 Battery Pack?[...]

4 Replacement Procedures 4.1 Overview Disassembly Procedures Three main types of cable connector are used. Pressure plate connector Spring connector Normal pin connector 1. When disconnecting a pressure plate connector , draw the tab on one side of the plastic pressure plate on the connector and pull the cable out from the connecto r. When reconnec[...]

4.1 Overview 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-5 Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the computer. Take your time [...]

4 Replacement Procedures 4.1 Overview Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage. NOTE : To tighten screws quickly and accu rately, an electric screwdriver is [...]

4.1 Overview 4 Replacement Procedures Grip Color Some screws have a colored grip area to he lp you determine the leng th of the screw. Even numbered length screws: Brown Odd numbered length screws: White Special length screw: Blue “Special length screw” means screws whose lengt h is indic ated in an integral number to th e first decimal places [...]

4 Replacement Procedures 4.2 Battery pack 4.2 Battery pack Removing the battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: Take care not to short circuit the te rminals when removing the battery pack. Similarly, do not drop, knock, scra tch, disassemble, twist, or bend the battery pack. 1. Turn off the[...]

4.2 Battery pack 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-9 Installing the battery pack To install the battery pack, fo llow th e steps below and refer to Figure 4-1. CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, operated, handled, or disposed correctly . Dispose[...]

4 Replacement Procedures 4.3 PC card/SD card 4.3 PC card/SD card 4.3.1 PC card Removing the PC card To remove the PC card, follow the steps below and refer to Figure 4-2. CAUTION: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manuals of the computer system you are using. 1. Push the eject button . It [...]

4.3 PC card/SD card 4 Replacement Procedures 4.3.2 SD card Removing the SD card To remove the SD card, follow the steps below and refer to Figure 4-3. CAUTION: Insert or remove the SD card in accordance with any instructions in the SD card manual or the manuals of the computer system you are using. 1. Push the SD card . It will pop out partly when [...]

4 Replacement Procedures 4.4 Expansion Memory module 4.4 Expansion Memory module CAUTION: The power of the computer must be turned off when you remove the memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch the memory module termi nals. Any dirt on the terminals may cause memory a[...]

4.4 Expansion Memory module 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-13 Installing the Expansion memory module To install the expansion memory module, fo llow the steps below and refer to Figure 4-4. CAUTION: The power must be turned off when y ou insert the memory module. Inserting a memory module with [...]

4 Replacement Procedures 4.5 HDD 4.5 HDD Removing the HDD To remove the HDD, follow the steps belo w and refer to Figure 4-5 to 4-7. CAUTION: Take care not to press on the top or bottom of the HDD. Pressure may cause data loss or damage to the device. 1. Remove the following screw and HDD slot cover . • M2 × 3S S-FLAT HEAD screw x1 HDD slot cove[...]

4.5 HDD 4 Replacement Procedures 2. Hold the tab of the HDD assembly and rem ove the HDD assembly from the connector CN4 of the HD FPC. HDD assembly Tab CN4 Figure 4-6 Removing the HDD assembly 3. Peel off two gaskets from the HDD unit and detach the HDD from the HDD holder . HDD HDD holder Gasket Figure 4-7 Removing the HDD PORTEGE R200 Mainten an[...]

4 Replacement Procedures 4.5 HDD Installing the HDD To install the HDD, follow the steps be low and refer to Figure 4-5 to 4-7. 1. Install the HDD to the HDD holder and stick two gaskets on the HDD unit. CAUTION: 1. When replacing the HDD, be sure to stick gaskets on the HDD unit. 2. Stick two gaskets in th e position shown below. Gasket 2. Insert [...]

4.6 Keyboard 4 Replacement Procedures 4.6 Keyboard Removing the keyboard To remove the keyboard, follow the steps below and refer to Figure 4-8 and 4-9. CAUTION: As the keytop may fall out, when handli ng the keyboard always hold it by the frame and do not touch the keytop. 1. Remove the following screw . • M2 × 4S BIND screw x1 2. Turn over the[...]

4 Replacement Procedures 4.6 Keyboard 6. Disconnect the keyboard flexible cable from the connector CN3200 on the system board and remove the keyboard . CN3200 Keyboard flexible cable Figure 4-9 Removing the keyboard Installing the keyboard To install the keyboard, follow the steps below and refer to Figure 4-8 and 4-9. 1. Place the keyboard face do[...]

4.7 Switch board 4 Replacement Procedures 4.7 Switch board Removing the Switch board To remove the switch board, follow the steps below and refer to Figure 4-10. 1. Turn over the computer and remove the following screw . • M2 × 8S BIND screw x1 2. Turn the computer face up and open the display. 3. Remove the switch cover . 4. Disconnect the swit[...]

4 Replacement Procedures 4.7 Switch board 4-20 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-519) Installing the Switch board To install the switch board, follow th e steps below and refer to Figure 4-10. 1. Connect the switch cable to the connector CN3270 on the system board. 2. Install the sw itch board according to the guide and se cure [...]

4.8 Touch pad 4 Replacement Procedures 4.8 Touch pad Removing the Touch pad To remove the touch pad, follow the step s below and refer to Figure 4-11 and 4-12. 1. Remove the touch pad cover while releasing the latches. Touch pad cover Figure 4-11 Removing the touch pad cover PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-21[...]

4 Replacement Procedures 4.8 Touch pad 2. Disconnect the touch pad cable from the connector CN3240 on the system board. 3. Remove the following screws fixing the touch pad assembly. • M2 × 3C S-FLAT HE AD screw x2 4. Remove the touch pad assembly from the palm rest while releasing the adhesive portion. 5. Disconnect the touch pad cable from the [...]

4.8 Touch pad 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-23 Installing the touch pad To install the touch pad, follow the step s below and refer to Figure 4-11 and 4-12. 1. Connect the touch pad cable to the connector on the touch pad assembly. 2. Install the touch pad assembly according to the g uide and [...]

4 Replacement Procedures 4.9 Cover assembly/Battery latch assembly 4.9 Cover assembly/Battery latch assembly Removing the Cover assembly/Battery latch assembly To remove the cover assem bly/battery latch asse mbly, follow the steps below and refer to Figure 4-13 to 4-15. 1. Turn over the computer and remove the following screws . • M2 × 4S BIND [...]

4.9 Cover assembly/Battery latch assembly 4 Replacement Procedures 2. Turn the computer face up and open the display. 3. Remove the following screws . • M2 × 4B S-FLAT HE AD screw x2 4. Remove the cover assembly by lifting it up from the base assembly. M2 × 4B S-FLAT HEAD Cover assembly Figure 4-14 Removing the cover assembly(2) PORTEGE R200 Ma[...]

4 Replacement Procedures 4.9 Cover assembly/Battery latch assembly 5. Remove the following screws and battery latch assembly . • M2 × 2.5B S-FLAT HEAD screw x3 Battery latch assembly M2 × 2.5B S-FLAT HEAD M2 × 2.5B S-FLAT HEAD Figure 4-15 Removing the battery latch assembly Installing the Cover assem bly/Battery latch assembly To install the c[...]

4.10 Bluetooth module 4 Replacement Procedures 4.10 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow th e steps below and refer to Figure 4-16. 1. Remove the following screw securing the Bluetooth module . • M2 × 3C S-FLAT HE AD screw x1 2. Disconnect the Bluetooth flat cable from both the Bluetoot h module a[...]

4 Replacement Procedures 4.11 Speaker/Fingerprint sensor board 4.11 Speaker/Fingerprint sensor board Removing the Speaker/Fingerprint sensor board To remove the speaker/fingerprint sensor boar d, follow the steps below and refer to Figure 4- 17 and 4-18. 1. Remove the following screw and lift up the SP FPC. • M2 × 3C S-FLAT HE AD screw x2 2. Dis[...]

4.11 Speaker/Fingerprint sensor board 4 Replacement Procedures 5. Remove the following screw and fingerprint sensor board . • M2 × 3C S-FLAT HE AD screw x1 M2 × 3C S-FLAT HEAD Fingerprint sensor board Figure 4-18 Removing the fingerprint sensor board Installing the Speaker/ Fingerprint sensor board To install the speaker/fingerpri nt sensor boa[...]

4 Replacement Procedures 4.12 MDC board 4.12 MDC board Removing the MDC board To remove the MDC board, follow the steps below and refer to Figure 4-19. 1. Remove the following screws and disconnect the MDC board from the connector CN3010 on the MP FPC. • M2 × 3C S-FLAT HE AD screw x2 2. Disconnect the MDC cable from the connector on the MDC boar[...]

4.13 RTC battery 4 Replacement Procedures 4.13 RTC battery Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-20. 1. Peel off the two glass tapes . 2. Disconnect the RTC battery cable from the connector CN9990 on the system board and remove the RTC battery from the RTC battery slot. CN9990 RTC battery G[...]

4 Replacement Procedures 4.14 Wireless LAN card 4.14 Wireless LAN card Removing the Wireless LAN card To remove the Wireless LAN card, follow the steps below and refer to Figure 4-21. 1. Disconnect the wireless LAN antenna cables (black and white) from the Wireless LAN card using an antenna co axial cable disconnector. 2. Press the two latches outw[...]

4.15 Fan 4 Replacement Procedures 4.15 Fan Removing the Fan To remove the fan, follow the steps below and refer to Figure 4-22. 1. Peel off the glass tape and disconnect the fan cable from the connector CN8770 on the system board. 2. Remove the following screws and fan . • M2 × 4C BIND screw x2 Glass tape Fan M2 × 4C BIND M2 × 4C BIND CN8770 F[...]

4 Replacement Procedures 4.16 MP FPC 4.16 MP FPC Removing the MP FPC To remove the MP FPC, follow the steps below and refer to Figure 4-23. 1. Remove the following screw and kill switch holder . • M2 × 3C S-FLAT HE AD screw x1 2. Remove the following screws and disconnect the MP FPC from the connector CN9500 on the system board. • M2 × 3C S-F[...]

4.16 MP FPC 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-35 Installing the MP FPC To install the MP FPC, follow the st eps below and refer to Figure 4-23. 1. Connect the MP FPC to the connector CN9500 on the system board and secure it with the following screws . • M2 × 3C S-FLAT HE AD screw x2 2. Install [...]

4 Replacement Procedures 4.17 HD FPC 4.17 HD FPC Removing the HD FPC To remove the HD FPC, follow the steps below and refer to Figure 4-24. 1. Peel off the glass tape and disconnect the HD FPC from the connector CN1800 on the system board. Glass tape HD FPC CN1800 Figure 4-24 Removing the HD FPC Installing the HD FPC To install the HD FPC, follow t[...]

4.18 PC card slot 4 Replacement Procedures 4.18 PC card slot Removing the PC card slot To remove the PC card slot, follow the steps below and refer to Figure 4-25. 1. Remove the following screws fixing the PC card slot. • M2 × 4C S-FLAT HE AD screw x2 2. Remove the PC card slot from the connector CN2110 on the system board. M2 × 4C S-FLAT HEAD [...]

4 Replacement Procedures 4.19 LAN/Modem jack 4.19 LAN/Modem jack Removing the LAN/Modem jack To remove the LAN/Modem jack, follow th e steps below and refer to Figure 4-26. 1. Disconnect the LAN cable from the connector CN4100 on the system board. 2. Remove the LAN/Modem jack from the slot. CN4100 LAN/Modem jack LAN cable Figure 4-26 Removing the L[...]

4.20 System board 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-39 4.20 System board Removing the System board To remove the system board, follow the steps below and refer to Figure 4-27. 1. Disconnect the LCD cable and FL cable from the connectors CN5600 and CN5601 on the system board. 2. Disconnect the LED [...]

4 Replacement Procedures 4.20 System board M2 × 3C S-FLAT HEAD System board Audio cover 4-40 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Figure 4-27 Removing the system board Installing the system board To install the system board, follow the steps below and refer to Figure 4-27. 1. Install the audio cover . 2. Install the system b[...]

4.21 Internal microphone 4 Replacement Procedures 4.21 Internal microphone Removing the Internal microphone To remove the internal microphone, follow the steps below and refer to Figure 4-28. 1. Disconnect the microphone cable from the connector CN6050 on the system board. 2. Remove the internal microphone from the microphone holder. Microphone cab[...]

4 Replacement Procedures 4.22 LED FPC 4.22 LED FPC Removing the LED FPC To remove the LED FPC, follow the steps below and refer to Figure 4-29. 1. Remove the following screws and LED FPC . • M2 × 3C S-FLAT HE AD screw x2 M2 × 3C S-FLAT HEAD LED FPC Figure 4-29 Removing the LED FPC Installing the LED FPC To install the LED FPC, follow the steps [...]

4.23 Display mask 4 Replacement Procedures 4.23 Display mask Removing the Display mask To remove the display mask, follow the steps below and refer to Figure 4-30. 1. Peel off the six mask seals and four LCD cushions on the LCD mask and remove the following screws . • M2 × 3.2S FLAT HEAD screw x8 (“3.2” in the figure below) • M2.5 × 4S FL[...]

4 Replacement Procedures 4.23 Display mask 4-44 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) Installing the Display mask To install the display mask, follow the steps below and refer to Figure 4-30. 1. Install the display mask while engaging the latches. 2. Secure the following screws to fix the display m ask. • M2 × 3.2S FLAT HEA[...]

4.24 FL inverter/LCD unit 4 Replacement Procedures 4.24 FL inverter/LCD unit Removing the FL inverter/LCD unit To remove the FL inverter/LCD unit, follow the steps below and refer to Figure 4-31 and 4- 32. 1. Remove the following screw fixing the FL inverter. • M2 × 3C S-FLAT HE AD screw x1 2. Peel the insulator and disconnect the two cables fro[...]

4 Replacement Procedures 4.24 FL inverter/LCD unit 4. Carefully lift up the top of the LCD unit and peel off the glass tape . 5. Disconnect the LCD cable and remove the LCD unit . Glass tape LCD cable LCD unit Figure 4-32 Removing the LCD unit 4-46 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9)[...]

4.24 FL inverter/LCD unit 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-47 Installing the FL inverter/LCD unit To install the FL inverter/LCD unit, follow th e steps below and refer to Figure 4-31 and 4-32. 1. Set the LCD unit to the display cover in place. 2. Connect the LCD cable to the LCD unit and stick t[...]

4 Replacement Procedures 4.25 Hinge 4.25 Hinge Removing the Hinge To remove the hinge, follow the steps below and refer to Figure 4-33 to 4-35. 1. Remove the following screws (back) and hinge caps (left and right). • M2 × 3C S-FLAT HE AD screw x2 M2 × 3C S-FLAT HEAD M2 × 3C S-FLAT HEAD Hinge cap Hinge cap Figure 4-33 Removing the hinge cap 4-4[...]

4.25 Hinge 4 Replacement Procedures 2. Remove the following screws (back) and palm rest . • M2.5 × 4B FLAT HEAD screw x4 M2.5 × 4B FLAT HEAD M2.5 × 4B FLAT HEAD Palm rest Figure 4-34 Removing the palm rest PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-49[...]

4 Replacement Procedures 4.25 Hinge 3. Take out the LCD cable from the hole. 4. Remove the following screws and hinges of the both sides. • M3 × 3S BIND screw x2 • M2 × 4B S-FLAT HE AD screw x2 LCD cable Hinge Hinge M3 × 3S BIND M3 × 3S BIND M2 × 4B S-FLAT HEAD M2 × 4B S-FLAT HEAD Figure 4-35 Removing the hinge 4-50 [CONFIDENTIAL ] PORTEG[...]

4.25 Hinge 4 Replacement Procedures PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] 4-51 Installing the hinge To install the hinge, follow the steps below and refer to Figure 4-33 to 4-35. 1. Install the both sides ’ hinges and secure them with the fo llowing screws . • M3 × 3S BIND screw x2 • M2 × 4B S-FLAT HE AD screw x2 2. Pas[...]

4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna 4.26 Wireless LAN antenna/Bluetooth antenna 4.26.1 Wireless LAN antenn a Removing the Wireless LAN antenna To remove the wireless LAN antenna, follow the steps below and refer to Figure 4-36. 1. Peel off the six acetate tapes on the display cover. 2. Peel off the wireless LAN ante[...]

4.26 Wireless LAN antenna/Bluetooth ant enna 4 Replacement Procedures 4.26.2 Bluetooth antenna Removing the Bluetooth antenna To remove the Bluetooth antenna, follow the steps below and refer to Figure 4-37. 1. Peel off the five acetate tapes on the display cover. 2. Peel off the Bluetooth antenna from the display cover and remove the it with the B[...]

4 Replacement Procedures 4.27 Fluorescent Lamp 4-54 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9) 4.27 Fluorescent Lamp This system uses LCD modules from the following supplier. Type Part.No Supplier Section 12.1 inch G33C0002C110 TMD 4.27.1 NOTE : - When working with a LCD module, always use a flat, grounded table. - Handle the backl[...]

4.27 Fluorescent Lamp 4 Replacement Procedures 4.27.1 Replacing the 12.1 Inch TMD fluorescent lamp The following describes the procedure for repl acing the fluorescent la mp (See Figure 4-38 to 4-47). Disassembling the module 1. Peel off tapes and insulating sheets. 1) Place carefully the module face up on a clean and flat worktable. To avoid scrat[...]

4 Replacement Procedures 4.27 Fluorescent Lamp 2. Removing screws 1) Spread out the insulation sheet without detach ing from the bezel side, as shown in the figure below. 2) Remove the left side screw and right side screw as shown in the figure below. CAUTION: Use a Philips screwdriver with type 0 bit to remove the scr ews. Pr oduct i o n l abe l F[...]

4.27 Fluorescent Lamp 4 Replacement Procedures 3. Removing the bezel 1) Place the module with the in sulation sheet facing upwards. 2) Release three latches of the upper bezel and frame. Unhook four latches (two each of both sides), peeling off the double-adhesi ve tape on the backside of the bezel slowly and remove the bezel. 3) Release four latch[...]

4 Replacement Procedures 4.27 Fluorescent Lamp 4. Opening up the PCB 1) Open the PCB to the horizontal po sition as shown in the figure below. CAUTION: Be careful not to damage the TAB. Figure 4-41 Replacing TM D fluorescent lamp(4) 4-58 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9)[...]

4.27 Fluorescent Lamp 4 Replacement Procedures 5. Removing the cell with the PCB 1) Remove the cell with the PCB from the b acklight unit as shown in the figure below . CAUTION: 1) Peel off the cell carefully not to break it. 2) Be careful not to damage the TAB. Cell Figure 4-42 Replacing To shiba fluorescent lamp( 5) PORTEGE R200 Mainten ance Manu[...]

4 Replacement Procedures 4.27 Fluorescent Lamp Assembling the module 1. Checking the back-light 1) Check the items shown in the Figure below. Do not let the sheet out of the frame. Do not let the sheet out of the frame. Figure 4-43 Replacing TM D fluorescent lamp(6) 4-60 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9)[...]

4.27 Fluorescent Lamp 4 Replacement Procedures 2. Assembling the cell with the PCB 1) Illuminate the backlight. 2) Make sure there is no scratch or dirt on the backlight. Also check the back of the cell. Next, install the cell with the PCB to the backlight unit. CAUTION: 1) Install by aligning the left under corner as shown below. 2) Be careful not[...]

4 Replacement Procedures 4.27 Fluorescent Lamp 3. Folding the TAB (PCB). 1) Fold the TAB (PCB) around the back of the backlight unit as shown in the figure below. CAUTION: 1) Be careful not to damage the TAB. Figure 4-45 Replacing TMD lamp(8) 4-62 [CONFIDENTIAL ] PORTEGE R200 Maintenance M anual (960-51 9)[...]

4.27 Fluorescent Lamp 4 Replacement Procedures 4. Installing the bezel 1) Install the bezel to the left under the fr ame. (as shown in the figure below (1).) 2) Engage the three latches at the bottom and stick the doubl e-adhesive tape of the bottom bezel to the cell. (as s hown in the figure b elow (2).) 3) Set the left side bezel to the frame. (a[...]

4 Replacement Procedures 4.27 Fluorescent Lamp 5. Screwing the PCB and the bezel 1) Use two screws to secure the left and right edge in the figure below. CAUTION: 1) The screw tightening torque is 0.167N·m (1.7kgf·cm) for all screws. 2) Use a Philips sc rewdriver with type 0 bit. 6. Installing the tapes and insulation sheets 1) Stick the double- [...]

[CONFIDENTIAL] Appendices[...]

Appendices App-ii [ CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519)[...]

Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] App-iii Appendix Contents Appendix A Handling the LCD Module ......................................................................... A-1 Appendix B Board Layout ................................................................................................B-1 B.1 System board [...]

Appendices App-iv [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) C.19 CN8800 DC-IN Connector (2pin) ..............................................................C-14 C.20 CN8810 1 st Battery Connector (10pin) .......................................................C-15 C.21 CN8770 Fan Connector (3pin)...................................[...]

Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] App-v Figures Figure B-1 System board layout (front) ...........................................................................B-1 Figure B-2 System board layout (Back) ...........................................................................B-3 Figure B-3 FDNFS* board layout [...]

Appendices App-vi [CONFIDENTIAL ] PORTEGE R200 Mainten ance Manual ( 960-519) Tables Table B-1 System board (front) .....................................................................................B-2 Table B-2 System board (back) .....................................................................................B-4 Table B-3 FDNFS* board ...[...]

Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] App-vii Table C-26 System Board I/F Connector (20pin) .......................................................... C-19 Table C-27 Speaker Connector (2pin) ........................................................................... C-19 Table C-28 FS Board I/F Connector (6pin) ....[...]

Appendices App-viii [CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519)[...]

Appendix A Handling the LCD Module Appendices Apx. A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it is pr[...]

Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with co tton or a soft cloth. If it is still dirty, try breathing on the surface to create a light cond ensate and wipe it again. If the surface is very dirty, we recomme nd a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surfa[...]

Appendix A Handling the LCD Module Appendices 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. PORTEGE [...]

Appendices Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. A-4 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual [...]

Appendix A Handling the LCD Module Appendices 9. Do not disassemble the LCD module. Disassembly can cause m a lfunctions. 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can damage the panel’s polarization. PORTEGE R200 Maint[...]

Appendices Appendix A Handling the LCD Module A-6 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)[...]

Appendix B Board Layout Appendices Apx. B Appendix B Board Layout B.1 System board Front View Figure B-1 System board layout (front) PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] B-1[...]

Appendices Appendix B Board Layout B-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manu al (960-519) Table B-1 System board (front) Mark Number Name (A) CN5620 External CRT Connector (B) CN6050 Internal Mi crophone connector (C) CN8800 DC-IN Connector (D) CN4610 USB 0 Connector (E) CN4611 USB 3 Connector (F) CN3260 LED Board Connector (G) CN3270 SW &a[...]

Appendix B Board Layout Appendices B.2 System board Back View Figure B-2 System board layout (Back) PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] B-3[...]

Appendices Appendix B Board Layout B-4 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manu al (960-519) Table B-2 System board (back) Mark Number name (A) CN999 0 RTC Battery Con nector (B) CN2110 PC Ca rd Con nector (C) CN1800 FDNHD* FP C Connector (D) CN4400 Bluetooth Connector (E) CN6170 FDNSP* FPC I/F Connector (F) CN8810 1 st Battery Connector (G) C[...]

Appendix B Board Layout Appendices B.3 FDNFS* board Front and Back View ( Front ) ( Back ) Figure B-3 FDNFS* board layout Table B-3 FDNFS* board Mark Number Name (A) CN950 FDNSP* FPC I/F Connecto r PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] B-5[...]

Appendices Appendix B Board Layout B.4 FDNMP* FPC Front View (Front) Figure B-4 FDNMP* FPC layout Table B-4 FDNMP* FPC Mark Number Name (A) CN2200 MINI PCI I/F Connector (B) CN9510 System Board I/F Connector (C) CN3010 MDC I/F Connector B-6 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manu al (960-519)[...]

Appendix B Board Layout Appendices B.5 FDNSP* FPC Front View (Front) Figure B-5 FDNSP* FPC layout Table B-5 FDNSP* FPC Mark Number Name (A) CN6 System Board I/F Connector (B) CN7 Speaker Connector (C) CN9 FDNFS* Board I/F Connector PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] B-7[...]

Appendices Appendix B Board Layout B-8 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manu al (960-519)[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-1 Apx. C Pin Ass i gnment Appendix C Pin Assignment System Board C.1 CN1400 SO-DIMM0 connector (200pin) Table C-1 SO-DIMM0 connector (200pin)(1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 MRVREF-B0V - 2 GND - 3 GND - 4 ADQ01-B1P I/O 5 ADQ05-B1[...]

Appendices Appendix C Pin Assignment C-2 [ CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519) Table C-1 SO-DIMM0 connector (200pin) (2/4) Pin No. Signal name I/O Pin No. Signal Name I/O 49 ADQS1-B1N I/O 50 N.C. - 51 ADQS1-B1P I/O 52 ADM1-B1P I/O 53 GND - 54 GND - 55 ADQ11-B1P I/O 56 ADQ15-B1P I/O 57 ADQ14-B1P I/O 58 ADQ10-B1P I/O 59 GND - 60 [...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-3 Table C-1 SO-DIMM0 connector (200pin) (3/4) Pin No. Signal name I/O Pin No. Signal Name I/O 111 1R8-B1V - 112 1R8 -B1V - 113 BCAS-B1N O 114 MODT2-B1P O 115 MCS3-B1N O 116 BMA13-B1P I/O 117 1R8-B1V - 118 1R8 -B1V - 119 MODT3-B1P O 120 N.C. - 121 GND -[...]

Appendices Appendix C Pin Assignment C-4 [ CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519) Table C-1 SO-DIMM0 connector (200pin) (4/4) Pin No. Signal name I/O Pin No. Signal Name I/O 173 ADQ50-B1P I/O 174 ADQ54-B1P I/O 175 ADQ51-B1P I/O 176 ADQ55-B1P I/O 177 GND - 178 GND - 179 ADQ56-B1P I/O 180 ADQ60-B1P I/O 181 ADQ57-B1P I/O 182 ADQ61-B1[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-5 C.2 CN1800 HD FPC I/F Connector (50pin) Table C-2 HD FPC I/F Connector (50pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND I 2 IDRSTRB-P3N O 3 POD07-P3P I/O 4 GND - 5 POD08-P3P I/O 6 PDD06-P3P I/O 7 PDD09-P3P I/O 8 GND - 9 PDD05-P3P I/O 10 [...]

Appendices Appendix C Pin Assignment C-6 [ CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519) C.3 CN2110 PC Card I/F connector (80pin) Table C-3 PC Card I/F connector (80pin) (1/2) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 A CAD00-EYP I/O 4 A CCD1-E3N I 5 A CAD01-EYP I/O 6 A CAD02-EYP I/O 7 A CAD03-EYP I/O 8 A CAD04-EY[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-7 Table C-3 PC Card I/F connector (80pin) (2/2) Pin No. Signal name I/O Pin No. Signal Name I/O 73 ACAD29-EYP I/O 74 ACAD30-EYP I/O 75 ACD02-EYP I/O 76 ACAD31-EYP I/O 77 ACCLKR-EYN I/O 78 ACCD2-E3N I 79 GND - 80 GND - C.4 IS2101 SD Card I/F Connector ([...]

Appendices Appendix C Pin Assignment C-8 [ CONFIDENTIAL] PORTEGE R200 Maintenance M anual (960-519) Table C-5 Docking I/F C onnector (50pin) (2/2) Pin No. Si g nal name I/O Pin No. Si g nal Name I/O 7 GND - 8 GND - 9 GND - 10 GND - 11 DOCSCL-P5P I/O 12 D-E5V - 13 D-E5V - 14 D-E5V - 15 DRED-PXP O 16 DGREEN-PXP O 17 DBLUE-PXP O 18 DHSYNC-P5P O 19 GND[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-9 C.6 CN3200 Keyboard I/F Connector (30pin) Table C-6 Keyboard I/F Connector (30pin) Pin No. Signal name I/O Pin No. Signal name I/O 1T GND - 2T GND - 1 N.C. - 2 N.C. - 3 CAPLED-P5N O 4 P5V - 5 KBSC00-S3N O 6 KBSC01-S3N O 7 KBSC02-S3N O 8 KBSC03-S3N O [...]

Appendices Appendix C Pin Assignment C-10 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) C.8 CN3260 LED I/F connector (13pin) Table C-8 LED I/F connector (13pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 HDDLED-P5N O 2 BTLED-S3P O 3 BAT2OR-S5N O 4 BAT2GR-S5N O 5 BAT1OR-S5N O 6 BAT1GR-S5N O 7 M5V - 8 M5V - 9 DCINOR-S5N O 10 DCIN[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-11 C.10 CN4400 Bluetooth I/F Connector (20pin) Table C-10 Bluetooth I/F Connector (20pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 BT-P3V - 2 N.C. - 3 N.C. - 4 USBBP4-S3N I/O 5 USBP4-S3P I/O 6 N.C. - 7 N.C. - 8 BTIFOF-S3N I 9 N.C. - 10 GND - 1[...]

Appendices Appendix C Pin Assignment C-12 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) C.12 CN4611 USB Port 3 Connector (4pin) Table C-12 USB Port 3 Connector (4pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 USBOPS-E5V I 2 USBP3-S3N I/O 3 USBP3-S3P I/O 4 GND - 1T GND - 2T GND - 3T GND - C.13 CN5600 LCD Connector (15pin) Table[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-13 C.14 CN5601 FL Inverter Conne ctor (8pin) Table C- 14 FL Inverter Connector (8pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 FL-P5V O 2 FL-P5V O 3 GND - 4 GND - 5 BKLPWM-P2P O 6 FL-P5V - 7 FL-P5V - 8 N.C. C.15 CN5620 RGB I/F Connector (15pin[...]

Appendices Appendix C Pin Assignment C-14 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) C.17 CN6170 SP FPC I/F Connector (20pin) Table C-17 SP FPC I/F Connector (20pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 P3V - 2 FGSPON-S3N O 3 GND - 4 USBP7-S3N I/O 5 USBP7-S3P I/O 6 GND - 7 N.C. - 8 SPOTR-PXN I/O 9 SPOTR-PXN I/O 10 SPOT[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-15 C.20 CN8810 1 st Battery Connector (10pin) Table C-20 1 st Battery Connector (10pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 (PVBL1) - 2 BTMP1 I 3 (DCHG) - 4 M5V - 5 PSCL-S5P I/O 6 PSDA-S5P I/O 7 GND - 8 DBT10V-S5N I 9 GND - 10 GND - C.21 [...]

Appendices Appendix C Pin Assignment C-16 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) C.23 CN3270 SW & LED I/F Connector (10pin) Table C- 23 SW & LED I/F Connector (10pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 P5V - 2 NC - 3 PNLOFF-S3N I 4 GND - 5 PWRSW-S3N I 6 GPBTNB-S3N I 7 GPBTNA-S3N I 8 NC - 9 (ARWLED) 10 (NU[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-17 Table C-24 MP FPC Connector (100pin)(2/2) Pin No. Signal name I/O Pin No. Signal name I/O 33 E3V - 34 AD29-P3P I/O 35 GND - 36 AD31-P3P I/O 37 AD23-P3P I/O 38 GND - 39 CBE3-P3N I/O 40 AD17-P3P I/O 41 GND - 42 CBE2-P3N I/O 43 GND - 44 PERR-P3N I/O 45[...]

Appendices Appendix C Pin Assignment C-18 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) C.25 CN9800 FS Board I/F Co nnector (6pin) (Not used) Table C- 25 FS Board I/F Connector (6pin) (Not used) Pin No. Signal name I/O Pin No. Signal name I/O 1 P3V - 2 FGSPON-S3N O 3 GND - 4 USBP6-S3N I/O 5 USBP6-S3P I/O 6 GND - 1T GND - 2T GND -[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-19 SP FPC C.26 CN6 System Boar d I/F Connector (20pin) Table C- 26 System Board I/F Connector (20pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 P3V - 2 FGSPON-S3N I 3 GND - 4 USBP7-S3N I/O 5 USBP7-S3P I/O 6 GND - 7 N.C. - 8 SPOTR-PXN I/O 9 SPOT[...]

Appendices Appendix C Pin Assignment C-20 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) MP FPC C.29 CN2200 MINI PCI I/F Connector (124pin) Table C- 29 MINI PCI I/F Connector (124pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 N.C. - 9 N.C. - 10 N.C. - 11 N.C. [...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-21 Table C-29 MINI PCI I/F Connector (124pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 55 GND - 56 PAR-P3P I/O 57 AD17-P3P I/O 58 AD18-P3P I/O 59 CBE2-P3N I/O 60 AD16-P3P I/O 61 IRDY-P3N I/O 62 GND - 63 P3V - 64 FRAME-P3N I/O 65 CLKRUN-P3N[...]

Appendices Appendix C Pin Assignment C-22 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) Table C-29 MINI PCI I/F Connector (124pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 115 N.C. - 116 N.C. - 117 GND - 118 N.C. - 119 GND - 120 GND - 121 N.C. - 122 N.C. - 123 N.C. - 124 E3V - C.30 CN3010 MDC I/F Connector (12pin) Table C[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-23 Table C-31 System Board I/F Connector (100pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 9 X97BC2-P3P I/O 10 GND - 11 WLON-S3N I 12 AD18-PSP I/O 13 GND - 14 AD16-P3P I/O 15 FRAME-P3N I/O 16 GND - 17 TRDY-P3N I/O 18 STOP-P3N I/O 19 GND - [...]

Appendices Appendix C Pin Assignment C-24 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519) Table C-31 System Board I/F Connector (100pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 69 AD26-P3P I/O 70 AD24-P3P I/O 71 GND - 72 MPIDSL-P3P I/O 73 AD22-P3P I/O 74 AD20-P3P I/O 75 GND - 76 PAR-P3P 77 AD11-P3P I/O 78 AD09-P3P I/O 79 G[...]

Appendix C Pin Assignment Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] C-25 FS Board C.32 CN950 SP FPC I/F Connector (6pin) Table C- 32 SP FPC I/F Connector (6pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 USBFS-S3P I/O 3 USBFS-S3N I/O 4 GND - 5 FGSPON-S3N I 6 P3V - 1T GND - 2T GND -[...]

Appendices Appendix C Pin Assignment C-26 [CONFIDENTIAL ] PORTEGE R200 Maint enance Manual ( 960-519)[...]

Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] D-1 Apx. D Keyboard S c an/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code s et 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 1[...]

Appendices Appendix D K eyboard Scan/Character Codes D-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance Ma nual (960-519) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code s et 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 [...]

Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E[...]

Appendices Appendix D K eyboard Scan/Character Codes D-4 [CONFIDENTIAL ] PORTEGE R200 Maintenance Ma nual (960-519) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — ?[...]

Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 5 5 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 7 5 I N S E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 7 6 D E L[...]

Appendices Appendix D K eyboard Scan/Character Codes D-6 [CONFIDENTIAL ] PORTEGE R200 Maintenance Ma nual (960-519) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Brea k 7 5 I N S E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 7 6 DE L E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0[...]

Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL ] D-7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 08 7 (7) 47 C7 6C F0 6C 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 [...]

Appendices Appendix D K eyboard Scan/Character Codes D-8 [CONFIDENTIAL ] PORTEGE R200 Maintenance Ma nual (960-519) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co m mo n* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout Figure E-1 Key layout (UK) Figure E-2 Key layout (US) PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] E-1[...]

Appendices Appendix E Key Layout E-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manu al (960-519)[...]

Appendix F Wiring diagrams Appendices Appendix F Appendix F Wiring diagrams F.1 LAN Loopback Connector Figure F-1 LAN loopback connector PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] F-1[...]

Appendices Appendix F Wiring diagrams F-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)[...]

Appendix G BIOS rewrite procedures Appendices Appendix G Appendix G BIOS rewrite procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk for the com puter that has renewed BIOS data. Rewriting the BIOS 1. Set the [...]

Appendices Appendix G BIOS rewrite procedures G-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)[...]

Appendix H EC/KBC rewrite procedures Appendices PORTEGE R200 Maintenance Manual (960-519) [CO NFIDENTIAL] H-1 Appendix H Appendix H EC/KBC rewrite procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  BIOS/EC/KBC rewriting disk for [...]

Appendices Appendix H EC/KBC rewrite procedures H-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519)[...]

Appendix I Reliability Appendices PORTEGE R200 Mainten ance Manual ( 960-519) [CONFIDENTIAL] I-1 Apx. I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table I-1 MTBF Component Time (hours) System 5,789[...]

Appendices Appendix I Reliability I-2 [CONFIDENTIAL ] PORTEGE R200 Maintenance Manual ( 960-519)[...]