Toshiba TCB-AX21UL инструкция обслуживания

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE) Installation Manual Installation Manua l Remote controller for air conditioner (Split type) 1 English Manuel du propriet aire Télécommande pour climatis eur (Type split) 15 Français Remote Controller Model name: Wireless remote controller kit TCB-AX21UL Generic model name Wireless remote control[...]

Wireless remote controller kit Installation Manual –1– Contents 1 ACCESSORY PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT . . . . . . . . . . 3 3 INSTALLATION LOCATION OF SIGNAL RECEIVING UNIT . . . . 4 4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT . . . . . . . . . . . 5 5[...]

Wireless remote controller kit Installation Manual –2– EN 1 ACCESSORY PARTS No. Parts Quantity 1 Signal receiving unit (provided 7.9” (200 mm) power cable) 1 2 Mounting bracket 1 3 Screws ∅ 0.16” x 1.0” (M4 x 25 mm) 2 4 Screws ∅ 0.16” x 1.6” (M4 x 40 mm) 2 5 Wood screws 2 6 Spacer 4 7 Wire joints 2 8 Cable tie 1 9 Pattern template[...]

Wireless remote controller kit Installation Manual –3– 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT 1 3 2 4 6 5 Screw Remove Face plate Remove the face plate from Signal receiving unit. Signal receiving unit Address selector sw itch This switch is used to address one of a maximum of six air conditione rs that can be controlled by the remote contr[...]

Wireless remote controller kit Installation Manual –4– EN 3 INSTALLATION LOCA TION OF SIGNAL RECEIVING UNIT • Do not install in a location where the air contains oil mist, such a s in a kitchen or factory. • Do not install next to a window, or in an y other location directly exposed to sunlight and outside air. • Do not install nea rby de[...]

Wireless remote controller kit Installation Manual –5– 4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT NOTE • To avoid malfunction of the re mote controlle r, do not assemble or run remote control wiring together w ith the power cabl es, an d do not enclo se them in the same metal conduit. • When the power u nit induces elec trical n oise, it is[...]

Wireless remote controller kit Installation Manual –6– EN 2. In order to later pass the Signal r eceiving unit wiring out through the upper case (thin part at the top center), use nippe rs or a similar tool to cut a notch in t he same size as the Signal receiving unit cord (optional). (Fig. B) 3. Disconnect the wires that were connected to the [...]

Wireless remote controller kit Installation Manual –7– 4. Use bracket parts (A) and (B) t o securely grip the ceiling material. (Fig. E) 5. Connect the Signal receiving unit wire (2-core) to the wire from the indoor unit. (Refer to “Wiring the Signal receiving unit.”) Check the terminal number on the indoor unit before wiring the Signal rec[...]

Wireless remote controller kit Installation Manual –8– EN 5 HOW TO PERFORM CABLING OF THE SIGNAL RECEIVING UNIT  Flush Mounting Connection diagram Provided wire joint (WHT 2) 1. Strip the insulation to approximately 0.55” ( 14 mm) from the ends of the wires to be connected. 2. Twist together the 2 wires and create a cr imp connection at th[...]

Wireless remote controller kit Installation Manual –9– 6 REQUIREMENT The control by two remote controll ers is enab led by in stalling the wireless remote contro ller with the wired remote controller for an indo or unit. (Max. 2 remote controllers of wireless or wired are insatiable.) “2-remote controllers” controlling means that one or mul[...]

Wireless remote controller kit Installation Manual –1 0– EN To operate a group control of mult iple indoor units by 2 remote controllers MAIN and SUB remote controll ers are operable even if they are installed to any indoor u nit. (Total cable length: Within 656’2” (200 m)) 7 HOW TO SET THE ROOM TEMPERATURE SENSOR • The room temperature s[...]

Wireless remote controller kit Installation Manual –1 1– 8 HOW TO SET THE ADDRESS SWITCH • When the multiple Signal receiving units are in stalled in the same room, an address can be set to prevent cross communication. • When replacing the battery an d pushing ACL button, the add ress of the remote controller becomes [ALL] and the Signal re[...]

Wireless remote controller kit Installation Manual –1 2– EN 10 SELF-DIAGNOSIS TA BLE AND MEASURES Lamp indication of Signal receiving unit 11 CAUTIONS FOR INSTALLATION OF THE REMOTE CONTROLLER • To operate the remote control ler by fixing it to the wall, etc. with a remote controlle r holder, turn on the fluorescent lamp, operate the remote c[...]

Wireless remote controller kit Installation Manual –1 3– 12 EXPLANATION TO CUSTOMERS • Hand over the “Owner’s Manual” and “Insta lla tion Manuals” to the customer after installation works. • Explain usage and maintena nce of the remote controller according to “Owner’s Manual”. 13 HOW TO HANDLE THE REMOTE CONTROLLER In case u[...]

Wireless remote controller kit Installation Manual –1 4– EN 14 TEST RUN Before test run • Before turning on the power supply switch, carry out the follo wing procedure. 1 Using 500V-megger, check 1M Ω or more exists between the terminal block 1 to 3 and the earth. If 1M Ω or less is detected, do not run the unit. D o not apply to the remote[...]

(EH99677601) 85464369216000 +00EH99677601_01EN_remo _IM.book Page 15 Thu rsday, October 8, 2009 4:12 PM[...]