Ultra Start 2250M инструкция обслуживания

FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the [...]

2250 Wiring Diagram Page 3 Pre-Installa tion Page 4 Components Recommended Pre-Installation Procedures Recommended Install Procedures Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 3 Pin Red Connector 4 Pin Blue Connector Jumper Selections Insta llation Page 6 Basic Installation - Quick star t Plugging In The Module Auto Tach Learn Shock S[...]

YELLOW WHITE/BLUE BLACK BROWN RED/WHITE PURPLE BLUE/WHITE PINK BLACK/WHITE BLUE WHITE GREEN/WHITE GREEN ORANGE 4 PIN Blu e SIDE VIEW ACTIVE RF ANTENNA Jumpers The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output. Note: The default setting is second ignition. Status Led?[...]

Recommended Pre-Installation Procedures - Control module - Remote transmitter(s) - Antenna with built in program button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness - 3 pin - 2 wire keyless entry harness - Multi-tone siren - Hood pin safety switch - Hood and window stickers - Installation guide - Owners manual BEFO[...]

Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness. Blue Ignition 1 30amp output 12volts in ignition and start positions. White Select Out 30amp [...]

QUICK START IN STALL QUICK START IN STALL Yellow Starter Output Connect The Yellow Wire From The 6 Pin T o The Vehicles Starter Wire. Green Heater Output Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current. Red 12 power Input Connect to Constant 12 Volt Pow[...]

QUICK START IN STALL Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes[...]

PROGRAM MODE - USER SETTINGS 1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse 2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock *3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock 1 Ignition Lock & Unlock Enabled 1 Light Flash Doors Lock / Unlock when the key is turned [...]

PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps. Release the Program Button . Press momentar[...]

1 Type 1 1 Flash Unlock before start and a lock pulse after start & shutdown 2 Type 2 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses 1Negative Input/ 30seconds 1 Flash Waits a maximum 30 seconds before starting. 2Timed Delay/ 15 Seconds 2 Flashes Ignition ON for 15 seconds before e[...]

PROGRAM MODE - TACH SETTINGS Setting 1- Method 2- Low Idle Tach Learning Setting 2- Adjust For Over-Crank (Tach or T achless) Setting 3- Adjust For Under-Crank (Tach or T achless) Shock Sensor - Self Learn Mode Anti Car Jacking Mode Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time. Step 2 -[...]

Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a “M ” Series Remote St[...]

ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady. Door locks and trunk rel[...]

14 INSTALLATION GUIDE OPERATIONS OPERATIONS 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. **This feature can help find your vehicle in a crowded parking lot. 2 sec . 1.Press and hold the UNLOCK button for three seconds. 2. The doors will unlock, continue holding the unlock b[...]

INSTALLATION GUIDE OPERATIONS OPERATIONS Remote Start Remote Stop Idle Mode Turbo Timer Mode Timer Mode Self Learning Shock Sensor 1.Press and release the button. 2.The park lights will flash and the siren will chirp once. 3.When the vehicle has started, the system will flash the park lights four times and then remain “On” while the vehicle is [...]

Blue Green Lock Un lock V ehicle Lock/Unlock Switch T o Control Relay or Actuators 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Veh icle Lock/Unlock Switch To C ontrol Relay or Actuator Green Fused +12V Blue Orange 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock Ve hicle Lock/Unlock Switch To Actuator Fused +12V x x Cut Cut [...]