Uniden XC710 инструкция обслуживания

[...]

[...]

11. To reduce the risk of electric shock. do not Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Read and understand all instructions. 12. Follow all warnings and instruction[...]

Battery Safety Precautions Introduction Caution: To reduce the risk of fire or injury to persons by the battery read and follow these instructions: Congratulations on your purchase of the Uniden XC61 0 Series/XC710 Cordless Telephone. This phone is designed to exacting standards which provide reliability, long life, and outstanding performance. 1. [...]

Included with the XC610 Series/XC710 If any of these items are missing or damaged, contact the place of purchased. Handset Base Unit Rechargeable Battery or Telephone Cord Telephone Cord AC Adapter for Australia for New Zealand (AAD-600S) Important Electrical Considerations . Unplug all electrical appliances when you know an electrical storm is app[...]

Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too distract[...]

Applying Power to the Base Unit All the XC610 Series/XC710 Cordless Telephone requires an AC outlet, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, connect the adapter as shown below. Important Wrap the power cord around the convenient notch on the bottom. Place the power cord so that it d[...]

Wall Installation Before mounting your phone, consider the following: l Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. l Make sure the wall material is capable of supporting the weight of the Base Unit and Handset. l Use screws with anc[...]

7. Plug the other end of the telephone line cord into the wall jack. 8. Plug the AC Adapter into a standard 230/ 240 AC wall outlet. Setting the Handset Retainer The handset retainer holds the Handset in place if your phone is mounted on a wall. The steps below describe how to remove and replace the retainer so that the tab faces up. 1. 2. Push up [...]

Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Installing the Handset Battery Pack 1. 2. 3. Press in on the Battery Cover Release. Slide the battery compartment cover down. Align the plastic connector of the Nickel-Cadmium battery pack with its socket and plug it in. Note:[...]

Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. We recommend that the battery pack charge for approximately 15-20 hours, without interruption, before plugging the phone line into your new phone. 1. 2. Place the Handset or the Base Unit.[...]

Continuous Battery Charging For the best battery performance, return the Handset to the Base Unit at the end of the day. This keeps the battery fully charged, so your phone works best. Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the TALK/BATT LOW LED flashes. If the TALK/BATT LOW LED begins to fla[...]

You can also select one of two different ringer tones for the Handset. Press @ to select a different ringer tone when the phone is not in use. To adjust the receiver volume, press @ while you are on a call. Handset Ringer Tone Select Button Handset Receiver Volume Control Automatic Digital Code Security To avoid unauthorised calls on your phone, a [...]

4. When the beeping stops, briefly remove the Handset again, and then return it to the Base Unit. Mote: The CHARGE LED will blink to indicate that the Digital Security Code is set to one of the more than 65,000 codes. If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will [...]

PRESS THESE YOU WILL HEAR KEYS Press @ A click similar to Note: Change when @ is channels to help pressed. CHANGING eliminate CHANNELS background noise. Changing Channels, Flash, and Page/Find To change channels or access call waiting while the phone is in use, or to use the one-way page to locate the Handset. follow these steps: If the call waitin[...]

4. If a pause is needed during dialing to @@ access a long distance service @@@@@@a press e. Note: The @ button counts as one digit. Pressing @ more than once increases the length of the pause between numbers. 5. Press @3 again. 6. Enter the memory location (0-9). A tone indicates that the number is stored. Storing a Mixed Number (Australian Model [...]

4. Press B on the Handset. 5. Enter the number to ;oifled in tone 6. If a pause is needed during dialing to access a long distance service, press @. Nofe: The @ button counts as one digit. Pressing @ more than once increases the length of the pause between numbers. 7. Press @ again. 8. Enter the memory location (0-9). A tone indicates that the numb[...]

4. Press the memory location number (0-9). Chain Dialing On certain occasions, after dialing a number, you may be requested by the party or service you are calling to enter a special access code, such as when performing a banking transaction. To do this, simply: 1. ;;;b;;~ access code into one of the memory 2. Dial the main number. 3. At the approp[...]

Troubleshooting If your XC610 Series/XC710 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service for assistance. Problem Suggestion Chanrge light won’t come l Make sure AC on when Handset is Adapter is plugged placed in Base Unit. [...]

Specifications WARRANTY General Frequency Control Modulation Operating Temperature Base Unit Receive Frequency Transmit Frequency Power Requirements Size Weight Handset Receive Frequency Transmit Frequency Power Requirements Size Weight Battety PLL FM - 10˚C to 50˚C 39.775 to 40.000 MHz (10 Channels) 30.075 to 30.300 MHz (10 Channels) 230V/240V A[...]