Vermont Casting IRHEDV32 инструкция обслуживания

1 10003929 10003929 01/02 Rev. 0 * Installation and service must be performed by a qualified installer, service agency or your gas supplier. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. FOR YOUR SAFETY WHA T T O DO IF YOU SMELL GAS: * Do not try to light any appliance. * Do not [...]

2 10003929 T ABLE OF CONTENTS Please read the Installation & Operating Instructions before using this appliance. Thank you and congratulations on your purchase of a Irving Oil fireplace. IMPORTANT - READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE STARTING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN A POSSIBLE FIRE HAZAR[...]

3 10003929 When the unit is installed into a woodburning fireplace, the minimum distance the mantel can be placed above the fireplace is governed by local building codes applicable to woodburning fireplaces. Consult local authorities having jurisdiction for these clearances. The underside of the mantel will become warm. Use only finishes which are [...]

4 10003929 FIREPLACE & TRIM DIMENSIONS R T Q U S V R - Fireplace opening width Q - Fireplace opening height S - Depth of insert T - Firebox width at insert depth(S) U - Firebox depth at insert back height (V) V - Insert back height MINIMUM FIREPLACE INSERT OPENING 1= SS or SSD Trim 2= SL or SLD Trim 3= SXL Trim 4= BSL Trim 5= BXL Trim T R I M F[...]

5 10003929 Do not use this appliance if any part of it has been under water. Immediately call a quali- fied service technician to inspect the unit and replace any part of the control which has been under water. When purging the gas line, the front glass must be removed. The gas pipeline can be brought into the fireplace base from the right side. It[...]

6 10003929 INSTALLATION OF TRIM SWITCH FOR RP GAS VALVES 1. Thread wire through openings on the right side of fireplace. Do not cut wire or insulation on metal edges. 2. Slide switch assembly from the back, between subframe and trim, then fasten the screw. (Fig. 3) 3. For left side installation reverse switch position in bracket and repeat Step 2 ([...]

7 10003929 Under no circumstances should insulation be put between the damper and the top of the unit. This may cause condensation and overheating of the unit. LINER INSTALLATION - Fig. 6 VENTING DIAGRAM Secure with clamp and three screws Flue gas exits through the vent termination rain cap 1) Attach flexible pipe to rain cap 2) Secure with clamp 3[...]

8 10003929 FLUE COLLAR PLATE MOVE BACK CABINET TOP FIG .4 FASTENER PLATE MAKE SURE THE FLUE COLLAR PLATE IS IN CONTACT WITH THE BACK EDGE OF THE CABINET TOP PLATE FLUE COLLAR CABINET TOP FIG.5 FASTENER PLATE MACHINE SCREW AFTER FASTENED Fig. 8 Fig. 9 Fig. 10 Fig. 11 FAN KIT Should this fan require servicing, the power supply must be disconnected. F[...]

9 10003929 GLASS FRAME W OPERA TING INSTRUCTIONS GENERAL GLASS INFORMATION Only ceramic glass approved by Vermont Castings Majestic Products Company may be used for replacement on this unit. 1. The use of substitute glass will void all product warranties. 2. Care must be taken to avoid breakage of the glass. 3. Under no circumstances should this ap[...]

10 10003929 CERAMIC REFRACTORY INSTALLATION 1. Remove front glass. 2. Remove logs from unit. 3. Remove refractory from package Refractory are fragile and must be han- dled with care. Where at all possible, two hands should be used when handling. 4. Take centre refractory and tilt so bottom edge slides into support angle in back of fireplace. Fig. 1[...]

11 10003929 L O H I Turn counterclockwise to decrease flame height. Turn clockwise to increase flame height. Fig. 18 FLAME ADJUSTMENT Flame adjustment is accomplished by rotating the Hi/Lo adjustment knob located near the centre of the gas control. (Fig. 18) It is important to periodically perform a visual check of the pilot and the burner flames. [...]

12 10003929 1. STOP! Read the safety information above on this label. 2. Turn off all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONLY, go on to Step 4. For RN/RP appliances turn the On/Off switch to off position or set thermostat to lowest level. 4. Open control access panel. 5. Push in gas control knob slightly and turn clock[...]

13 10003929 SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off pilot and electrode at pilot. push the red button again. If pilot will not light - check gap at electrode and pilot-should be 1/8" to have a strong spark. B. Defective ignitor (P[...]

14 10003929 • GAS SUPPLY ON • SUPPLY LINE HOOKED UP • SHUTOFF VALVE OPEN NO NO NO NO • LOCKOUT HAS ENGAGED. WAIT 60 SECONDS AND TRY AGAIN. • FOR SPARK AT ELECTRODE WHILE DEPRESSING PIEZO — 1/8" GAP TO PILOT HOOD NEEDED. • ALL WIRING CONNECTIONS • REPLACE PIEZO IGNITOR • FOR AIR IN THE LINES • THERMOPILE NEEDS A MINIMUM 325m[...]

15 10003929 REPLACEMENT P ARTS IRHEDV32 35 30 31 32 27 29 28 25 26 3 2 33 34 22 24 15 L O H I PILOT ADJ PILOT ON OFF 23 a/b 21 20 19 14 12 16 8 a/b 9 a/b 13 18 17 11 a/b 18 10a/b[...]

16 10003929 REPLACEMENT P ARTS LIST Description IRHEDV32 1 Log Set Complete 57896 1a Log Ember Front KR1 1b Log Front Left KR2 1c Log Front Right KR3 1d Log Rear KR4 1e Log Top Left KR5 1f Log Top Right KR6 2 Lava Rock (Package) 10001454 3 Burner Lava Rock (Package) 57897 4a Burner Complete With Tiles (Nat.) 10000198 4b Burner Complete With Tiles ([...]

10003929 A-TRIM OPTIONS FOR RHEDV32 17 FRAME ASSEMBLY 1. Lay Trim Top Facing and Trim Side Facings, face down on to an even surface such as a table or floor. Be sure not to scratch the painted surfaces. 2. Install the nuts and bolts (Fig. 21). Fig. 21 A1) RHESS, RHESL, RHESSD, RHESLD & RHESXL TRIMS RHESS, RHESL, RHESSD, RHESLD and RHESXL TRIM A[...]

10003929 Fit Decorative Frame to the fireplace and fasten (Fig. 25). Plastic on the trim must be removed before mounting onto the fireplace. Glass must be tightly pressed against the front of the frame in order to prevent screws from damaging glass edges. Fig. 25 AS SHOWN FROM FRONT SCREWS FRAME MOUNTING GENERAL INFORMATION The Decorative Front Fra[...]

10003929 KEY DESCRIPTION RHESS (2) RHESL (3) RHESSD (3) RHESLD (3) RHESXL (4) 1 Trim Frame Top, Flat Black 57929 57932 57929 57932 57935 2 Trim Frame Left, Flat Black 57927 57930 57927 57930 57933 3 Trim Frame Right, Flat Black 57928 57931 57928 57931 57934 4 Trim Top Deflector (1) 17634 17634 17634 17634 17634 5 Trim Top Channel (1) 50586 50587 17[...]

10003929 TRIM ASSEMBLY 1. Install trim channels (left and right sides). Use two screws to assemble each piece. 2. Slide on the trim top channel and fasten it from the back side. 3. Install the trim top deflector and use two screws to fasten it. (Fig. 26) 4. Remove ALL plastic protective covering from brass trim. RHEBSL Fig. 26 To install the kit yo[...]

10003929 A3) RHEF A and RHEFP TRIMS Glass Frame Louvre Note: Position brass trim top as shown (small end up) to prevent heat discolouration Fig. 27 Fig. 28 1. Remove the front glass (see "Glass Frame Re- moval" section). 2. Install support window trim channel, top and bottom brass trim by using the shortest black screw. (Fig. 43 & 44)[...]

10003929 A4) HEBTKP , HESBTKP , HECBTK, HECBTKMB & HEBT A TRIMS HECBTK - Cast bay window and grills in classic black trim kit HECBKMB - Cast bay window and grills in midnight black porcelain enamel trim kit HESBTKP - Steel bay window with polished brass and cast grills in classic black trim kit HEBTKP - Steel bay window and bay louvres with pol[...]

10003929 1) Reposition controls. a) Remove the Fan Speed Control Box (Fig. 33). b) Attach the Fan Speed Control Box to the Bracket (Fig. 34) and install the Bracket into the Cabinet. Only for RN/RP VALVE units. c) Install the Control Knobs Extensions onto the appropriate Control Valve Knobs (Fig. 34). On units fitted with a Honeywell brand control [...]

10003929 Fig. 39. Attach magnets and brass trim to the steel frame. Fig. 40. Bracket for HEBTKP. Fig. 37. Hang the Window Grille or the Steel Frame onto the lower tabs of the Hanging Brackets. Fig. 38. Engage the slots in the Upper Grille Top Louvre with the upper tabs of the Hang- ing Brackets. 24[...]

10003929 (1) With magnets. IMPORTANT: Only Trim Panel Assemblies Approved by Vermont Castings Majestic Products Company Can Be Used on These Products. ALL repair parts will be available from your local dealer. When ordering, always give the following information: Model and serial number, part description with finish and part number; 11 12 15 14 16 [...]

10003929 26 1. Install the unit according to Homeowner’s Manual. 2. Install the trim according to Installation Instructions. 3. Remove the two (2) screws at the bottom of the trim. 4. Install the riser at the bottom of the trim (Fig. 58). 5. Fasten the trim with the same two (2) screws removed on step 3. Note: The riser kit should only be used wi[...]

10003929 8" x 12" VENT TERMINATION KIT Model: HEDVT (8" x 12") (Fit Typical 8" x 12" and 9" x 13" flue Tile) Kit Includes: A - 8" x 12" Vent Termination (x1) B - Stainless Steel Clamps 3"-3.5" (x4) C - Hardware Package (x1) D - High Temperature Sealant (x1) FLEX VENT KIT Model: HEDVK25 Inc[...]