Whirlpool 9.76E+13 инструкция обслуживания

Installation Instructions 30" Electric Slide-In Range 1 9 758642 9758642 Quic k Ref er ence Ta ble of Cont ents: P ages 2 3 3 4 5 - 8 9 Before you start P roduct dimensions Cabinet dimensions/requirements Electrical requirements Installation steps Chec k operation If range does not operate If you need assistance/service Moving the range Pa rt [...]

2 Bef or e you star t... Mobile home installation The installation of this range must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, P art 3280 [formerly the F ederal Standard for Mobile Home Construction and Safety , Title 24, HUD (Par t 280)] or , when suc h standard is not applicable, the Standard for Manufact[...]

3 Pr oduct dimensions Cabinet dimensions/r equir ements Cabinet opening dimensions shown are for: 25" (63.5 cm) countertop depth, 24" (61 .0 cm) base cabinet depth, 36" (91 .4 cm) countertop height 26-7/8" (68.3 cm) depth with handle 36" (91 .4 cm) cooktop height with leveling legs lowered 1 -1/2 turns 22-1/2" (57 .1 c[...]

4 Slide-in r ang es: count er t op pr eparations The cooktop sides of the slide-in range fit o ver the cutout edge of your counter top. If you have a square finish (flat) countertop and the opening width is 30" (7 6.2 cm), no countertop preparation is required. Fo rmed front-edged countertops: Must have molded edge shaved flat 1/2" (1 .3 [...]

5 No w star t... 1. R emo ve shipping materials, tape and protective film from range. Keep cardboard bottom and shipping base under range. Remo ve oven rac ks and parts pac kage from inside oven. 2. Ta ke four cardboard corners from the carton. Stac k one cardboard corner on top of another . Repeat with other two corners. Place them lengthwise on t[...]

6 P ow er supply cord method: 1. Disconnect power . 2. Remo ve the knoc kout for the 40 amp power supply cord. 3. Assemble a U.L.-listed strain relief in the opening. 4. Insert the power supply cord through the strain relief, allowing enough slac k to easily at tac h the wiring to the terminal bloc k. W ARNING - Improper connection of the equipment[...]

7 Dir ect wir e method: Copper or Aluminum wir e This range may be connected directly to the fuse disconnect or circuit breaker box; or with a U.L.-listed, 40 amp range power supply cable. Depending on your electrical supply , mak e the required three-wire or four -wire connection. 1. Disconnect power . 2. Remo ve the knoc kout as needed for condui[...]

8 9. Move range close to cabinet opening. 10 . R emove cardboard or hardboard from under range. Carefully move range into final position. 11. P ull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remo ve drawer and set it aside on a protected surface. Oper ating position 13 . If installing the range [...]

9 Chec k oper ation 17 . Chec k the operation of the cooktop elements: P ush in and turn eac h surface unit control knob to “HI” position. Chec k the operation of the cooktop elements and indicator lights. 18 . Chec k the operation of the oven element: P ress the “BAKE” pad. “350°F” will appear in the temperature display . Press the ?[...]

10 When moving range, slide range onto cardboard or hardboard to prevent damaging the floor covering. If removing the range is necessary for cleaning or maintenance: 1. Unplug range or disconnect power . 2. Slide range forward to complete cleaning or maintenance. 3. Make sure the anti-tip brac k et is installed: • Look for the anti-tip brac ket s[...]

11 Notes[...]

12 Pa rt No. 9758642 P rinted in U .S.A. © 20 04 Whirlpool Corporation Benton Harbor , Mic higan 49022 0 1/2004[...]