Whirlpool WSR413YW0 инструкция обслуживания

b& ChIJ Inst’dfat ion Instructions WHIRLPOOL UNDERCOUNTER REVERSE OSMOSIS WATER FILTRATION SYSTEM IV[...]

Remove parts from packages. Check that you have all the parts. storage tank with base (A) filtration assembly cover (B) two mounting screws (C) g-volt battery (D) filtration assembly (E) 3/e” blue tubing (F) l/4” yellow tubing (G) l/4” orange tubing (H) RO membrane cartridge (I) I n %” red tubing wiih push-in connector attached (K) l/4” g[...]

Before You Start . . . HOOK UP WATER I L, IMPORTANT: Read and save these instructions. It is recommended that this system be installed by a licensed plumber. It is the responsibility of the installer to comply with the installation specifications provided and with state and local plumbing codes. If you decided to install the system yourself, see ?[...]

- - Instructions At A Glance l For detailed instructions see following page. 1. Turn off cold water supply. (Steps la-lb) 3. Connect saddle valve to cold water supply. (Steps We or 1 h-lj) 2. Turn on faucet to drain water from line. (Step 1 b) 4. Turn saddle valve handle clockwise until piercing lance enters pope and stops. (Steps If-19 or 1 k-l I)[...]

Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. la Take note of water requirements listed . under the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve. Do not use sadd[...]

Instructions At A Glance l For detailed I. Connect faucet spout, chrome base plate, indicator light disk and rubber washer to faucet base. (Steps 2a-2b) nstructions see following page. 2. Connect green tubing and black tubing to faucet. (Steps 2c-2d) 3. Place faucet in sink opening. Secure faucet to sink 4. Connect faucet indicator wire to wire har[...]

Front view of air gap faucet _ chrome base elate indicator - light wire t ;fby;; Fhex nut Is- %” grey connector with push-in end Side view of air gap faucet k spout air gap hole slnk %” tubing black %” tubing must ;lor; downward to blue %” tubing Property Damage l Contact a qualified installer or licensed plumber for cutting a faucet openin[...]

Instructions At A Glance l For detailed instructions see following page. 1. Install RO cartridge into filtration assembly. Connect one end of red tubing to bottom of RO cartridge. Connect other end to green tubing from faucet. (Steps 3a-3e) 3. Use orange tubing from filtration assembly to fill storage tank with water. (Steps 3g-3h) Connect orange t[...]

The filtration assembly should already be . placed close to its final location. Move storage tank near its final location, which should be within four feet of filtration assembly. The filtration assembly may be installed under a sink or in the basement (mounted to wood floor supports or to the basement wall). For basement installation order Basemen[...]

Instructions At A Glance l For detailed instructions see following page. 1. Decide where drain saddle will be mounted. w , The best place is on a horizontal drain tailpiece I above (before) the trap. (Steps 4a-4b) , 2. Connect drain saddle to drain pipe. (Step 4c) 3. Drill hole in drain using o drain saddle as a guide. ( t ening in tep 4d) 4. Threa[...]

Electrical Shock Hazard Special care must be taken when drilling into water pipes. Some water may remain in pipe. - If an electric drill is used, it must be properly grounded to prevent severe or lethal shock if water should enter drill. Use only an electric drill with a 3-wire power supply cord connected to a grounded receptacle. l Check with a qu[...]

Flush System Instructions At A Glance l For detailed instructions see following page. I. Slide filtration assembly onto mounting screws. 2. Turn on faucet and drain tank to flush (Step 5a) disinfectant from tank. (Step 5b) 3. Turn on cold water supply and saddle valve. (Step 5c) 4. Allow tank to fill - ap roximately 4 hours. Lift faucet handle to d[...]

Flush System 5a Slide filtration asse . mounting holes onto mounting screws that were installed in step 3b. DO NOT kink or bend tubing. Insulated staples may be used to secure tubing to cabinet walls. Tighten mount- ing screws to secure filtration assembly to wall. Replace fil- tration assembly cover. 5b In step 3h you filled the storage tank with [...]

Water Requirements The filtration system must be connected to a cold water supply line providing 40-l 00 psi water pressure. If psi is less than 40, a booster pump, (Part Number 4373525) will be needed. Review the water application guideline chart below to determine if your water meets the standards necessary to use this water filtration system. DO[...]

Using your RO water filtration system To get purified water from the storage tank - Hold the faucet handle down for momentary flow, hold the faucet up for continuous flow. To stop water flow from the faucet - Return the faucet to the center or horizontal position. When faucet flow slows or drips - The storage tank is empty. Wait 1 hour before dispe[...]

How to sanitize the storage tank You will need to order Tank Sanitizing Kit, Part No. 4373527. You will also need household bleach and a measuring spoon. 1. Turn off saddle valve in water line. Open faucet and drain storage tank. There will be no water dripping when tank is empty. 2. Turn off faucet. Push in grey connector to disconnect yellow tubi[...]

Performance Data Sheet @ Q This Reverse Osmosis System has been tested and listed by NSF International under Standard 58 for the water treatment claims listed below under “Contaminant Reduction Performance”. Whirlpool Reverse Osmosis Water Filtration System IV Model No. WSR413YW Test Parameters TDS = 200500 mg/L2 pH = 7.5 Turbidity = 1 NTU Temp[...]

Part No. 4373500 Rev B 01993 Whirlpool Corporation Whirlpool Corporation Benton Harbor, MI 49022 @ Printed on Recycled Paper in U.S.A.[...]