White Rodgers 1F95-391 инструкция обслуживания

WHITE-RODGERS 90 SERIES 1F95-391 MUL TI-ST AGE/HEA T PUMP INST ALLA TION/CONFIGURA TION This White-Rodgers Digital Thermostat uses microcomputer technology to provide precise time, humidity , and temperature control. This thermostat offers the flexibility to design 1F95-391 : 7 Day programming; residen- tial applications. ELECTRICAL D A T A Electri[...]

A TTENTION! This product does not contain mercury . However , this product may replace a unit which contains mercury . Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury . W earing non-absorbent gloves, take up the spilled mercury with sand or other absorbent material and place into a container which can be seale[...]

HEA T PUMP TERMINAL OUTPUTS Refer to equipment manufacturers’ instruc- tions for specific system wiring information. Y ou can configure the thermostat for use with the following heat pump system types: HEA T PUMP TYPE 1. Single-stage compressor system; gas or electric backup. HEA T PUMP TYPE 2. Multi-stage or two- compressor system; gas or electr[...]

RESET SWITCH See the T roubleshooting section at the end of this document for more information about the function of this switch. E2/P SWITCH (DHM) TERMINAL FUNCTION The E2/P switch is located on the back of the thermostat body (see fig. 2). This switch controls how the DHM terminal will be energized. 1. In the P position (up) the DHM terminal will[...]

INST ALLER CONFIGURA TION BEFORE TURNING POWER ON, please read the following instructions. Befor e operating the system, you must configure the thermostat to operate properly with your equipment. The thermostat, as it comes from the factory , is configured to operate a standard multi- stage electric forced hot air system with a single stage air con[...]

INST ALLER T ABLE NOTE: You must be in the User Configuration Menu to enter the Installer Table. Firmly press TIME FWD and TIME BACK at same time and release to enter the Configuration Menu. 6 1 ML TI STG HEA T PUMP 2 HEA T PUMP (1) 2 Selects type of system. Selecting HEA T PUMP makes additional items for heat pump systems av ailable. 3 ELEC HEA T [...]

These numbers are approximate and represent operation with a typical system. Actual temperature differentials and run times may vary widely based on your building and equipment, as well as outdoor temperature conditions. COMPRESSOR OFF DELA Y Installer table, step 1 1 is available if the fossil fuel kit alternative option (PUMP OFF) is selected. Th[...]

The Service Button Menu allows you to view or program as many as 4 reminders that indicate when service is required. 1. Humidifiers = A programmable run time in hours to indicate on the LCD when the humidifier will need to be serviced. 2. Air Filters = A programmable run time in hours to indicate on the LCD when the filter will need to be serviced [...]

TR OUBLESHOO TING F AN OPERA TION If your system does not have a G terminal Connection, skip to HEA T/HUMIDITY section below . 1. Turn power on to the system. 2. Press PROGRAM RUN . 3. Press FA N until F AN ON is displayed. The fan should begin to operate. 4. Press FA N until F AN AUT O is displayed. The fan should stop operating, unless a call for[...]

Symptom P ossible Cause Corrective Action No Heat/No Cool/No Fan 1. Blown fuse or tripped circuit breaker . Replace fuse or reset breaker . (Common Prob lems) 2. Furnace power switch to OFF . T ur n switch to ON. 3. Furnace blow er compar tment door or Replace door panel in proper position to engage panel loose or not properly installed. saf ety in[...]

Symptom P ossible Cause Corrective Action Thermostat Setting and Thermostat 1. Thermostat ther mometer setting requires The thermometer can be adjusted +/- 5 degrees. Thermometer Disagree adjustment. See T emperature Displa y Adjustment in the Operating Manual under Configuration. Thermostat Display Sho ws CHCK P AD, 1. Thermostat ser vice indicato[...]

The Emerson logo is a trademark and a service mar k of Emerson Electric Co.[...]