Woods Equipment CZ2252K инструкция обслуживания

RF4164852 P ARTS / OPERA TIONS MANUAL MOW’N MACHINE MAN0820 REV A 12-2009 CZ1736K 872291F 17HP KA W W/36” SIDE DISCHARGE CZ2048K 872298F 20HP KA W W/48” SIDE DISCHARGE CZ2252K 872299F 22HP KA W W/52” SIDE DISCHARGE CZ2361B 872404F 23HP B&S W/61” SIDE DISCHARGE CZ2461K 872405F 24HP B&S W/61” SIDE DISCHARGE Includes Maintenance In[...]

CALIFORNIA Proposition 65 W arning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer , birth defects and other reproductive harm. Californie Proposition 65 A vertissement L e s é c ha pp em en t s d e s m o te ur s d ie se l e t c e rt ai ns d e le ur s c om p o sé s s on t r ec o n nu s p ar [...]

3 WOODS 12-2009 IMPORT ANT MESSAGE TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer . Read manual instructions and safety rules. Make sure all items on the Dealer ’s Pre-Delivery and Delivery Check Lists in the Set-Up instructions are completed before releasing equipment to the owner . Th[...]

4 WOODS T ABLE OF CONTENTS FIGURES P AGE SAFETY ....................................................................................................................................................... 5-1 1 SET -UP INSTRUCTIONS .......................................................................................................................... [...]

5 WOODS SAFETY NOTICE !!! Unauthorized modications may present extreme safety hazards to operators and bystanders and could also result in product damage. Woods strongly warns against, rejects and disclaims any modications, add-on accessories or product alterations that are not designed, developed, tested and approved by Woods Engineering Dep[...]

6 WOODS SAFETY Site preparation and circumstances - Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by the manufacturer . - Clear the area to be mowed of objects such as rocks, toys, wire or other debris that may be picked up or throw[...]

7 WOODS Machine preparation - Check operator presence interlock system and brake operation. Adjust or repair any problems before using. - Do not tamper with or defeat safety devices. Keep guards, shields and interlock safety devices in place and in proper working condition. They are for your protection. - Keep all fasteners such as nuts, bolts and [...]

8 WOODS SAFETY Starting - Start only according to instructions in this manual or on the machine. - Before attempting to start the engine, make sure: - the parking brake is on; - the PTO is disengaged; - the traction drive is in NEUTRAL. - When starting the engine, make sure hands and feet are clear of the blades. - Do not start the machine while st[...]

9 WOODS SAFETY W ARNING MANEUVERING SAFEL Y In general - Slow down before turning. - Do not mow in reverse unless absolutely necessary . Always look behind and down for small children and pets before and during backing. - Be aware when approaching blind corners, shrubs, trees, tall grass or other objects that may obscure vision. - If tires lose tra[...]

10 WOODS SAFETY MAINTENANCE SAFETY In general - Maintain machine according to manufacturer's schedule and instructions for maximum safety and best mowing results. - Park machine on level ground. - Never allow untrained personnel to service ma- chine. - Adjust or repair only after the engine has been stopped and the blades have quit rotating. -[...]

11 WOODS SAFETY BA TTER Y Battery acid is caustic and fumes are explosive and can cause serious injury or death. T o reduce the risk of personal injury when working near a bat- tery: - When working with battery acid, use protective equipment such as, but not limited to, goggles, face shield, rubber gloves and apron. - Avoid leaning over a battery .[...]

12 WOODS SET -UP INSTRUCTIONS TOOLS REqUIRED FOR ASSEMBL Y - Wrecking bar - Claw hammer - Sockets: 1/2”, 15/16 - Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16” - T ire pressure gauge NOTE: All references below to the “right” or “left” are with respect to an operator at the controls. 1. UNCRA TE UNIT a) Discard packing materials. Loosen[...]

13 WOODS SET UP INSTRUCTIONS 4. FINAL PREP ARA TIONS - Check the engine and hydraulic oil levels. T op off with the correct oil if necessary . Use 10W30 motor oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. See engine operation manual for specied motor oil viscosity . - Charge battery and properly connect cables. S[...]

14 WOODS LABELS[...]

15 WOODS LABELS[...]

16 WOODS LABELS DECAL IS LOCA TED UNDER FOOTPLA TE .[...]

17 WOODS LABELS[...]

18 WOODS CONTROLS At operator's right side KEYSWITCH (K) - The keyswitch has three positions: OFF , RUN , and ST ART . Insert the key and turn it clockwise to move the switch from OFF to RUN . T urn it further to ST ART and hold to engage the starter . Release the key and the switch will return to RUN from ST ART . T urn the key counterclockwi[...]

19 WOODS FUEL SELECT OR V AL VE (U) The fuel tank selector valve is located behind the seat. The fuel tank selector valve has three positions: Off : The tank selector is of f when the lever points down. The selector should be of f whenever the machine is transported or stands unused for any length of time. Shutting off the fuel supply avoids the po[...]

20 WOODS Reverse movement - T o move the machine straight back, pull both traction levers back equally from their neutral position. Reverse speed increases as the levers are moved back farther . Maximum reverse speed is reached when the levers hit the rear of the forward-reverse slot. When moving in reverse, push- ing the levers forward slows the m[...]

21 WOODS CONTROLS P ARKING BRAKE (R) - Pull the parking brake lever up and back to put the parking brake ON. Push it forward and down to put the parking brake OFF . The parking brake must be ON to start the engine. It must also be ON to keep the engine running if the operator leaves the seat. The parking brake must be OFF to keep the engine running[...]

22 WOODS PRE-OPERA TION CHECK LIST PRE-OPERA TION CHECK LIST (OPERA TOR’S RESPONSIBILITY) ___ Review and follow all safety rules and safety decal instructions. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Check to make sure all shields and guards are properly installed and in good condition. Be sur[...]

23 WOODS OPERA TION FUELING - Fill fuel tank with good quality , clean, unleaded regular gasoline. Do not use hi-test fuel. - Use a funnel to avoid spilling. W ARNING TO CHECK OR ADD FUEL: – Do it outdoors – Do not smoke – Stop engine; allow to cool – Fill to one inch below bottom of ller neck – Do not overll – Clean up spilled fu[...]

24 WOODS OPERA TION OPERA TING NOTES - Practice at slow engine and travel speeds with the PTO of f until fully familiar with the controls. - For normal cutting the throttle should be set at the full open position. By using the traction levers to speed up or slow down the machine during use, maximum control and cutting efciency can be maintained.[...]

25 WOODS OPERA TION CUTTING 1. Place the discharge chute in the down position or correctly t a grass collector or mulcher plate. 2. Sit in the seat. 3. Start the engine. 4. T urn the blades on by pulling up on the PTO switch. Do not start the blades at full throttle. Instead, use the slowest throttle setting that will al- low the engine to pick [...]

26 WOODS MAINTENANCE CHART E C N A N E T N I A M N O I T A R E P O n e e w t e b s e m i t m u m i x a m e r a s l a v r e t n i e s e h T . b o j g n i o g n o n a s i e c n a n e t n i a M . s n o i t i d n o c e r e v e s r e d n u n e t f o e r o m m r o f r e P . s n o i t a r e p o e c n a n e t n i a m 5 T S R I F S R U O H E R O F E B H C A[...]

27 WOODS MAINTENANCE RECORD NOTES ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ______________________[...]

28 WOODS MAINTENANCE CHECK DAIL Y Operator Presence Interlock System - Start Operation For the engine to crank, the parking brake must be on, the PTO (blades) of f and traction levers in the neutral lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the blades on, and either traction lever out[...]

29 WOODS MAINTENANCE LUBRICA TION Every 50 hours of operation, lubricate the following points (1-3) with grease: 1. Deck lift lever (1 point) 2. Deck lift pivots (4 points) 3. Pull arms (2 points located at the front of the cutterdeck) 4. Caster wheel pivots (2 points) (Lubricate every 500 hours or once a year) NOTE ON BLADE SPINDLES - The blade sp[...]

30 WOODS MAINTENANCE SP ARK PLUGS Remove each plug and check condition. - Good operating conditions are indicated if the plug has a light coating of grey or tan deposit. - A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both may be caused by a clogged air cleaner or improper carburetor adj[...]

31 WOODS MAINTENANCE AIR CLEANER Clean and replace the air cleaner element as speci- ed in the service chart. Uneven running, lack of power or black exhaust may indicate a dirty air cleaner . 1. Unclamp end cover C and remove existing cleaner element A . 2. Insert new element A and replace cover C . Ensure breathing port B is pointing down and t[...]

32 WOODS MAINTENANCE ENGINE COOLING Continued operation with a clogged cooling system will cause severe overheating and can result in en- gine damage. - Daily : Clean air intake screen V . - Every 100 hours : Clean cooling ns beneath blower housing H with reference to information in the engine manufacturer's manual. SPECIFIC TORqUES S T L O[...]

33 WOODS MAINTENANCE TRANSAXLES Inattention to proper safety , operation, or maintenance procedures could result in personal injury , or damage to the equipment. Schiller Grounds Care, Inc. recommends returning the machine to your authorized Schiller Grounds Care, Inc. dealer for service or repair . Perform transaxle maintenance with the engine off[...]

34 WOODS MAINTENANCE BLADE BALANCE Blade balance must be maintained at 5/8 oz-in (19.4 g-cm) or less. Failure to keep blades balanced causes excess vibration, wear , and shortened life of most components of the machine. T o balance a blade: 1. Sharpen blade rst. 2. Balance the blade at the center . 3. Attach a 1/8 oz (3.9 g) weight at a distance[...]

35 WOODS ADJUSTMENTS DECK LEVELING 1. Park the machine on a smooth, level surface. Raise the deck to the transport position. 2. Lower the deck onto a set of equal height blocks under the rear corners of the deck. Place an- other set of blocks under the front of the deck so that the deck top is pitched forward 1/8". NOTE: The front and rear of [...]

36 WOODS ADJUSTMENTS FIGURE 1 P ARKING BRAKE FOR 36", 42", 48", AND 52" MODELS NOTE: There are 2 brakes, 1 on each transaxle. The parking brake should keep the machine from moving. T o check the parking brake, park the ma- chine on a level surface, open the bypass valves and set the parking brake to ON . Attempt to move the mach[...]

37 WOODS ADJUSTMENTS X B FIGURE 1 P ARKING BRAKE FOR 61" MODELS NOTE: There are 2 brakes, 1 on each transaxle. The parking brake should keep the machine from moving. T o check the parking brake, park the ma- chine on a level surface, open the bypass valves and set the parking brake to ON . Attempt to move the machine forward and backward by pu[...]

38 WOODS ADJUSTMENTS HYDROST A TIC TRANSAXLE ADJUST - MENTS A turnbuckle style hydro stat neutral adjustment is provided. Neutral: 1. Support the machine with the rear wheels off the ground. Use jack stands or equivalent sup- port. Do not rely only on mechanical or hydraulic jacks. 2. Move the traction levers out into the neutral lock position and [...]

39 WOODS ADJUSTMENTS ARM REST HEIGHT ADJUSTMENTS 1. Remove acorn nuts 1 , plastic washers 2 , arm rest 3 and second set of plastic washers 4 . 2. Adjust carriage bolts 5 to desired height A , B , or C by pushingg on the carriage bolts 5 until they are free from the locking slot, adjusting them to the desired height and then pulling the carriage bol[...]

40 WOODS BEL T REPLACEMENT NOTE: Always use Woods replacement belts, not general purpose belts. Woods belts are specially designed for use on this mower and will normally last longer . CUTTERDECK BEL T 1. Remove oorplate. 2. Set the cutterdeck in a middle height-of-cut posi- tion. 3. Use a 3/8" ratchet and extension to back tensioning idler[...]

41 WOODS HYDRO TRANSAXLE DRIVE BEL T 1. Remove cutterdeck belt (see cutterdeck belt replacement). 2. Disconnect wire I at clutch M . Remove bolts J and remove torque restraint. 3. Using a ratchet with a 9/16" socket, place over nut at location P . Use the ratchet to rotate it enough to remove the transaxle drive belt. 4. Install a new transaxl[...]

42 WOODS NOTES ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ _________________________________________[...]

43 WOODS P ARTS SECTION P ARTS SECTION[...]

44 WOODS FIGURE 1 FRAME-ENGINE/CLUTCH ASSY 4 3 2 19 8 9 20 12 24 22 5 10 6 7 18 14 30 17 15 JUMPER HARNESS 11 16 ON LY ON LY 10 16 KA W ENGINE B & S ENGINE 25 23 1 27 26 21 27 28 13 29 31 32[...]

ITM P ART NO. DESCRIPTION qTY 45 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 1 FRAME-ENGINE/CLUTCH ASSY 1 4164364 ENGINE-18HP KA W 1 4164365 ENGINE-20HP KA W 1 38666.W FIL TER-FUEL 4164537 FIL TER-OIL 4164329 FIL TER-AIR (USED ON MODELS 9CZ2048K) 4164366 ENGINE-22HP KA W 1 4164367 ENGINE-24HP KA W 1 38666.W FIL TER-FUEL 4164630 FIL TER-AIR 4164631 F[...]

46 WOODS 42 FIGURE 2 TRANSAXLE ASSY[...]

ITM P ART NO. DESCRIPTION qTY 47 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 2 TRANSAXLE ASSY 1 4164049 S-FRAME W/LABELS 1 2 4162973 SHAFT -PULLARM MOUNT 1 3 4163957.7 WLDMT -PULL ARM 2 4 4163819 ARM-CONTROL 2 5 4156464 AXLE-LH 1 (INCLUDES ITEMS 4, 25, 26, 27, 32, 39 & 40) (USED ON 36", 48" AND 52" DECKS ONL Y) 6 64163-29 W ASHER [...]

48 WOODS FIGURE 3 FUEL T ANK/BUMPER & CONTROL P ANEL 4 18 22 3 2 9 13 10 5 11 14 12 6 7 21 8 19 17 15 16 24 23 25 18 / 27 21 16 15 17 30 32 31 30 28 29 26 33 35 34[...]

ITM P ART NO. DESCRIPTION qTY 49 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 3 FUEL T ANK/BUMPER & CONTROL P ANEL 1 4164049 S-FRAME W/LABS 1 2 4142840-3 T ANK-FUEL RH 1 3 4142841-3 T ANK-FUEL LH 1 4 4163041.7 BUMPER 1 (USED ON 36", 42", 48" AND 52" DECKS) 4164221.7 BUMPER 1 (USED ON 61" DECKS ONL Y) 5 4164526 S-CONTROL P[...]

50 WOODS FIGURE 4 FUEL V AL VE & COVER PLA TE 1[...]

ITM P ART NO. DESCRIPTION qTY 51 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 4 FUEL V AL VE & COVER PLA TE 1 4164049 S-FRAME W/LABS 1 2 4142840-1 T ANK-FUEL RH 1 3 4142841-1 T ANK-FUEL LH 1 4 64197-001 BL T -TDFM 5/16-18X3/4 4 5 4164803.7 COVER-FRAME, REAR 1 6 88042N HOSE CLAMP 6 7 4162977-009 HOSE-1/4 FUEL LINE 24" 3 8 2188161 V AL VE-T AN[...]

52 WOODS FIGURE 5 DECK LIFT ASSEMBL Y 1 9 9 10 16 17 10 8 20 34 24 33 21 29 27 21 22 7 6 19 19 25 18 2 5 15 14 14 4 14 14 15 13 14 14 11 12 11 12 17 16 3 CUTTERDECK 11 31 11 32 26 11 30 28 23 6 2 16[...]

ITM P ART NO. DESCRIPTION qTY 53 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 5 DECK LIFT ASSEMBL Y 1 4164049 S-FRAME W/LABS 1 2 64205-060 BOL T -MET M12-1.75X50 4 3 4164565.7 WLDMT -DECKLIFT , FRONT 1 4 4163894.7 WLDMT -DECKLIFT REAR 1 5 4109960 WLDMT -DECK LIFT ROD 2 6 64221-02 E-RING .250 2 7 4163891.7 BRKT -LIFT LINK 1 8 2188143 GRIP 1 9 64123-50[...]

54 WOODS FIGURE 6 CASTER ASSEMBL Y 20 19[...]

ITM P ART NO. DESCRIPTION qTY 55 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 6 CASTER ASSEMBL Y 1 4164049 S-FRAME W/LABS 1 2 4162986 DUST COVER 2 3 85010N ZERK-1/4-28 2 4 64025-20 NUT -HEX 3/4-16 SLOT U 2 5 64163-26 W ASHER 2 6 48043-03C CUP-OUTER BEARING 4 7 48043-04C CONE-OUTER BEARING 4 8 48480.W SEAL 2 9 4143675.7 WLDMT -CASTER 2 (USED ON 36&quo[...]

56 WOODS FIGURE 7 KICKPLA TE/SEA T ASSEMBL Y 13 1 6 7 5 5 3 12 12 11 8 9 8 10 12 9 21 16 17 22 23 24 14 19 20 18 15 4 2[...]

ITM P ART NO. DESCRIPTION qTY 57 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 7 KICKPLA TE/SEA T ASSEMBL Y 1 4164049 S-FRAME W/LABS, 1 2 4163703 SEA T ASSY . 1 *4163703-01 SEA T BACK 1 *4163703-02 SEA T BOTTOM 1 *4163703-03 ARM REST P AD 2 *4163703-04 LH ARM MOUNTING BRKT 1 *4163703-05 RH ARM MOUNTING BRKT 1 3 4163281.7 PLA TE-SEA T 1 4 4124009 SWITC[...]

58 WOODS FIGURE 8 STEERING[...]

ITM P ART NO. DESCRIPTION qTY 59 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 8 STEERING 1 4144705 GRIP-HANDLE 2 2 4156297.7 LEVER-TRACTION CNTRL 2 3 4156295 WLDMT -CONTROL BAR, RH 1 * 4156294 WLDMT -CONTROL BAR, LH 1 4 4143673.7 WLDMT -CONTROL BOX RH 1 5 4143674.7 WLDMT -CONTROL BOX LH 1 6 108208.W SWITCH DBL POLE 2 7 64197-015 BL T -TDFM 10-32X1/2 [...]

60 WOODS FIGURE 9 P ARKING BRAKE 2 17[...]

ITM P ART NO. DESCRIPTION qTY 61 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 9 P ARKING BRAKE 1 4164049 S-FRAME W/LABST 1 2 4156464 TRANSAXLE, RH 1 (USED ON 36", 42", 48", AND 52" ONL Y) 3 64197-015 BL T -TDFM 10-32X1/2 T ORX 2 4 64168-2 COTTER-HAIRPIN.08X1.19 2 5 4148697 ROD-BYP ASS CONTROL 2 6 4146187 BEARING-FLANGE 1 7 64221-0[...]

62 WOODS FIGURE 10 WIRE HARNESS OB PO OP DB WB BRY YB RW GY BR YELLOW W/ BLACK STRIPE RED W/ WHITE STRIPE GREEN W/ YELLOW STRIPE BROWN W/ YELLOW STRIPE ORANGE W/ BLACK STRIPE PURPLE W/ ORANGE STRIPE ORANGE W/ PURPLE STRIPE DARK BLUE YELLOW BROWN Y BLACK GREEN RED B G R WHITE W/ BLACK STRIPE WIRE COLORS PURPLE ORANGE WHITE P O W 2 (BLACK) ENGINE BLO[...]

ITM P ART NO. DESCRIPTION qTY 63 ITM P ART NO. DESCRIPTION qTY WOODS 1 4154880 HARNESS-MAIN WIRE 1 2 148082-20 FUSE 20 AMP 2 3 30-419 CABLE-BA TT 4 GA BLK 29" 1 4 4124009 SWITCH-SEA T NO 1 5 4136792 METER-HOUR 1 6 30-180 CABLE-BA TT 4 GA RED 29" 1 (USED ON 22HP , 23HP , AND 24HP ONL Y) 2722227-02 CABLE-BA TTERY W/COND 1 (USED ON 18HP AND [...]

64 WOODS FIGURE 1 1 36" SIDE DISCHARGE 26 15 16 5 4 14 17 23 3 22 16 TO RQUE TO 70 FT -LBS 12 13 4 11 10 9 10 5 14 16 17 15 2 21 21 25 6 24 28 29 7 30 8 31 27 1 20 18 6 21 33 37 38 21 39 37 34 40 35 21 37 41 45 37 42 43 44 31 32 36 36 44 42 43 19 46[...]

ITM P ART NO. DESCRIPTION qTY 65 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 1 1 36" SIDE DISCHARGE 1 4152858 S-36 DECK W/LABELS 1 2 41471 15 CHUTE-RUBBER 1 3 1 1 2 1 1 1 - 0 2 K T 2 BLADE 18.00 OFFST HLFT 2 4 41 15850 S-ASSY SPINDLE OUTER 2 5 4144947 PULLEY -SPINDLE 2 6 128169 PULLEY , IDLER 5.50 2 7 4146065 ARM, DECK IDLER ASSY 1 (INCLUDES IT[...]

66 WOODS FIGURE 12 48" SIDE DISCHARGE 57[...]

ITM P ART NO. DESCRIPTION qTY 67 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 12 48" SIDE DISCHARGE 1 4146864 S-48 DECK W/LABELS 1 2 4146596.25 GUARD-LH 48" DECK 1 3 4146595.25 GUARD-RH 48" DECK 1 4 41471 15 CHUTE-RUBBER 1 5 64123-50 BOL T -HEX 3/8-16X1 9 6 64018-1 1 BOL T -CRG 1/2-13X3LG 2 7 64229-03 LOCKNUT -NYLON 3/8-16 25 8 64205-0[...]

68 WOODS FIGURE 13 52" SIDE DISCHARGE[...]

ITM P ART NO. DESCRIPTION qTY 69 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 13 52" SIDE DISCHARGE 1 4153817 S-52 DECK W/LABELS 1 2 4143552.25 GUARD-LH 52" DECK 1 3 4143553.25 GUARD-RH 52" DECK 1 4 41471 15 CHUTE-RUBBER ASSY 1 5 64123-50 BOL T -HEX 3/8-16X1 9 6 64018-1 1 BOL T -CRG 1/2-13X3LG 2 7 64229-03 LOCKNUT -NYLON 3/8-16 24 8 64[...]

70 WOODS FIGURE 14 61" SIDE DISCHARGE 40 69 32 22 33 14 57 58 62 57 59 4 24 60 3 35 39 9 13 7 45 7 37 12 69 40 36 6 21 44 11 34 38 63 54 52 35 15 28 18 19 11 27 41 55 17 25 10 21 11 34 38 16 30 23 29 8 31 7 16 47 53 47 47 42 51 61 53 48 53 46 49 53 48 53 50 46 45 43 45 35 35 35 53 56 35 26 2 4 64 7 5 20 53 53 65 67 TO RQUE TO 70 FT . LBS 66 70[...]

ITM P ART NO. DESCRIPTION qTY 71 ITM P ART NO. DESCRIPTION qTY WOODS 61" SIDE DISCHARGE FIGURE 14 1 4164130 S-61" DECK 1 2 4163809.25 BEL T COVER RH 1 3 4163808.25 BEL T COVER LH 1 4 38524.W KNOB-4 PRONG 3/8-16 2 5 4147399 CHUTE-RUBBER ASSY 1 6 64158-08 EYE BOL T 1 7 64229-03 LOCKNUT NYLON 3/8-16 28 8 64123-31 BL T -HEX 1/2-13X3 2 9 27215[...]

72 WOODS FIGURE 15 BEL TS-CUTTERDECK 2 3 4 5[...]

ITM P ART NO. DESCRIPTION qTY 73 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 15 BEL TS-CUTTERDECK 1 4144212 BEL T -36" CUTTERDECK 1 2 4143733 BEL T -52" CUTTERDECK 1 3 4147095 BEL T -48" CUTTERDECK 1 4 4163569 BEL T -61" CUTTERDECK 1 5 4147716 BEL T -42" CUTTERDECK 1[...]

74 WOODS FIGURE 16 DECALS-POWERUNIT 1 2 4 5 (UNDER SEA T) 8 17 11 13 14 7 6 10 16 4 12 9 18 18 3 (UNDER FOOTPL AT E)[...]

ITM P ART NO. DESCRIPTION qTY 75 ITM P ART NO. DESCRIPTION qTY WOODS FIGURE 16 DECALS-POWERUNIT 1 4144768 LABEL-CONTROL P ANEL 1 2 2000570 LABEL-W ARN FUEL PICT . 2 3 4164525 LABEL-INFORMA TION 1 4 4152340 LABEL-WOODS 2 5 2000590 LABEL-W ARN BA TTERY 1 6 2000701 LABEL-LH TRACTION 1 7 2000700 LABEL-RH TRACTION 1 8 4126804 LABEL-P ARKING BRAKE 1 9 41[...]

F-8045 MM & Boundary (Rev . 12/1/2008) Wo od s Eq u i p me n t Comp any 260 6 South Illinois R oute 2 Post Of fice Box 1000 Oregon, Illinois 610 61 8 00-319-663 7 tel 800-3 99-6 63 7 fax www .W oodsEquipment.com LIMITED W ARRAN TY (Mow ’ n Machine TM Zer o-T ur n Mo wers and W oods Boundary TM Utility V ehicles) Please Enter Information Belo [...]

F-8495 MM & Boundary Repair Parts (Rev . 2/15/2006) W oods Equip ment Company 260 6 South Illinois Route 2 Post Office B ox 1000 Oregon, Illinois 610 61 800-319-663 7 tel 800-39 9-663 7 fax www .W oodsEquipment.com LIMITED W ARRANTY (Mo w’ n Machine TM Zero-T urn Mo wer and W oods Boundary TM Utility V ehicle R eplacement P arts) W oods Equip[...]

Woods Equipment Company 2606 South Illinois Route 2 Post Ofce Box 1000 Oregon, Illinois 61061 800-319-6637 tel 800-399-6637 fax www .WoodsEquipment.com ©2008 Woods Equipment Company . All rights reserved. WOODS, the Woods logo, and “T ested. Proven. Unbeatable.” are trademarks of Woods Equipment Company . All other trademarks, trade names, [...]