Yamaha EMX640 инструкция обслуживания

POWERED MIXER E Owner’ s Manual Contents Front and rear panel ............................................ 2 Control panel .......................................................... 2 Input/output panel .................................................. 6 Rear panel .............................................................. 7 Connections ....[...]

2 Front and rear panel EMX640—Owner’s Manual Front and rear panel Control panel ■ Channel section In this section, y ou can adjust equalization (fre- quency response), volume level, effect and moni- tor output levels for the input signal of each channel. 1 Equalizer controls (HIGH, MID, LOW) This is a 3-band equalizer that adjusts the high fr[...]

Control panel 3 EMX640—Owner’s Manual ■ DIGIT AL EFFECT section This section allows y ou to turn the built-in digital effect on/off and to select the effect ty pe. 6 Effect select switch Select the effect ty pe for the built-in digital effect. 7 DIGIT AL EFFECT ON switch W hen this switch is on (pressed), the digital effect built into the EMX[...]

4 Front and rear panel EMX640—Owner’s Manual ■ MONITOR section This section allows y ou to adjust the t one and volume of the MONITOR bus, and specify the mix level of the built-in effect. 9 Graphic equalizer This is a 7-band graphic equalizer that allows you to adjust the frequency r esponse of the MONI- T OR bus signal, pr oviding a maximum[...]

Control panel 5 EMX640—Owner’s Manual ■ POWER AMP section This section allows y ou to select the signals that will be output from the built-in two-channel powe r amplifier , and t o select the BRIDGE mode. I LIMITER indicator This indicator lights up when the level of the sig- nal output from the po wer amp section re aches the maximum and t[...]

6 Front and rear panel EMX640—Owner’s Manual Input/output panel 1 Channel input jacks (Hi-Z, Lo-Z) 1~4 These are the input jacks for channels 1~4. By using the P AD switches (c ontrol panel 5 ) you can connect an y of the jacks to a w ide range of sources fr om mics to line lev el dev ices (synthesiz- ers or rhythm bo x es etc.). The Lo-Z jacks[...]

Rear panel 7 EMX640—Owner’s Manual The nominal input level and impedance ar e – 10 dB/600 Ω for the A UX IN jack, and –10 dB V/ 600 Ω for the T APE IN jacks. 6 External output jacks (REC OUT/MONI- TOR/MAIN) These are output jacks which send line lev el sig- nals from the EMX640 t o external devices. A ste- reo rec ording device such as [...]

8 Connections EMX640—Owner’s Manual Connections W hen connecting various devices, be sur e to use cables and plugs of the appropriate standar d. ■ Speaker connection There ar e three wa ys in which speakers can be c onnected t o the EMX640; a single speaker each can be c on- nected to either the A or the B jack of POWER AMP 1 and of POWER AMP[...]

Basic Operation 9 EMX640—Owner’s Manual Basic Operation This section explains basic operation of the EMX640. Connecting microphones and instruments 1 Before connecting mics or instruments, make sure that the power of all equip- ment (where applicable) is turned off. Also make sure that the level controls of each channel of the EMX640 and the MA[...]

10 Example setups EMX640—Owner’s Manual Example setups This section pro vides some ways in which the EMX640 can be used, and explains c onnections and operation. As a conference P A system/installed sound system Her e is an example of using the EMX640 as a conference P A system or as an installed sound system. Connections • Connect mics t o c[...]

As a band PA 11 EMX640—Owner’s Manual As a band P A Her e is an example of using the EMX640 as a small P A for a band. In this example, the monitor speakers are being sent a mix that is independent of the MAIN speaker mix. An ext ernal effect such as delay or r everb is also being used. Connections • Connect mics or instruments, such as k eyb[...]

12 Example setups EMX640—Owner’s Manual Sending an independent mix to the monitor speakers 1 Set the MONITOR section MASTER con- trol to the √ √ √ √ position. 2 Raise the MONI controls for the channels that you wish to hear from the monitor speakers. 3 Use the graphic equalizers and MASTER controls of the MAIN/MONITOR sections to adjust[...]

Specifications 13 EMX640—Owner’s Manual Specifications ■ General specifications Maximum output po wer 200 W/4 Ω @0.5% THD at 1 kHz Frequency response 20 Hz~20 kHz +1 dB, –3 dB @1 W output into 8 Ω (POWER AMP OUT) 20 Hz~20 kHz +1 dB, –3 dB @+4 dB output into 10 k Ω (MAIN OUT , MONIT OR OUT , EFFECT SEND) T otal harmonic distortion [...]

14 Specifications EMX640—Owner’s Manual ■ Input specifications ■ Output specifications • All output jacks are unbalanced. • 0 dB=0.775 Vrms, 0 dBV=1 Vrms. Specifications are subject to c hange without pr ior notice. 1. Sensitivity is the lo west lev el that can produce an output of +4 dB (1.23 V) or the nominal output level when the [...]

Dimensions 15 EMX640—Owner’s Manual ■ Dimensions ■ Block and Level diagram 470 W: 480 260 H: 275 D: 275 Unit: mm Clipping level EFFECT OUT REC OUT MAIN, MONITOR POWER AMP BRIDGE 30 dB MAIN BRIDGE MAIN MAIN MAIN MONITOR ADD SUM DIGITAL EFFECT TAPE IN AUX IN LINE HI-Z PAD:ON MIC Lo-Z PAD:ON HI-Z PAD:OFF EFFECT RTN EFFECT RTN Lo-Z PAD:OFF EFFE[...]

Y AMAHA CORPORA TION VY66080 R2 1 IP 16 Pro Audio Division, #18/3 P .O. Box 3, Hamamatsu, 430-8651, Japan NP Printed in T aiwan FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by[...]