Zanussi ZBA32050SA инструкция обслуживания

EN User manual Refrigerator ZBA32050SA[...]

Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Care and Cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 What to do if… _ _ _ _ _ _ _ _ _ _ _[...]

If the refriger ant circuit should become dam- aged: – avoid open flames and sources of ignition – thoroughly ventilate t he room in which the appliance is situated • It is dangerous to alter the specifications or modify this product in a ny way. Any damage to the cord may cause a short-circuit, fire and/or electric shock. Warning! Any electr[...]

• This product must be serviced by an autho r- ized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in ei- ther its refrigerant circui t or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbi[...]

First use Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typi cal smell of a brand-new product, then dry thoroughly. Important! Do not use detergents or abrasive powders, as these will dama ge the finish. Daily use Mova[...]

Care and Cleaning Caution! Unplug the appliance before carrying out any maintenance operation. This appliance contains hydrocarbons in its cooling unit; main t enance and recharging must therefore only be carried out by authorized technicians. Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with lu [...]

Problem Possible cause Solution The appliance does not op- erate. The lamp does not operate. The appliance is switched off. Switch on the appliance. The mains plug is not connected to the mains socket correctly. Connect the mains plug to the mains socket correctly. The appliance has no power. There is no voltage in the mains socket. Connect a diffe[...]

Installation Caution! Read the "Safety Information" carefully for your safety and correct operation of t he appliance before installing the appliance. Positioning Warning! If you are discarding an old appliance that has a lock or catch on the door, you must ensure that it is made unusable to prevent young childr en being trapped inside. I[...]

6. Switch on the appliance. The appliance is supplied with a 13 amp plug fitted B . In the event of having to change the fuse in the plug supplied, a 13 amp ASTA ap- proved (BS 1362) fuse must be used. Warning! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely. Door reversibility T[...]

Installing the appliance Caution! Make sure that the mains cable can move freely. Do the following steps: x x If necessary cut the adhesi ve sealing strip and then apply it to the appliance as shown in figure. 2 3 Ø 2.5 mm 13 mm 1 Drill the appliance using a Ø 2.5 mm drill (10 mm max. penetration). Fix the square fitting to the appliance. 1 2 Ins[...]

44mm 4mm Adjust the appliance in the niche. Make sure that the distance between the appli- ance and the cupboard front-edge is 44 mm. The lower hinge cover (in the accessories bag) makes sure that the distance between the appli- ance and the kitchen furniture is correct. Make sure that the cl earance between the appli- ance and the cupboard is 4 mm[...]

B E D C E Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. Disconnect the parts (Ha), (Hb), (Hc) and (Hd). 21 mm ~50 mm ~50 mm 90 o 90 o 90 o Install the part (Ha) on t he inner side of the kitch- en furniture. 12 www.zanussi.com[...]

Ha Hc Push the part (Hc) on the part (Ha). Ha Hb 8 mm Open the appliance door and the kitchen furni- ture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. Remove the small squares and drill holes with ø 2 mm at 8 mm from the out er edge of the door. P[...]

Hb Align the kitchen furniture door and the appli- ance door by adjusting the part (Hb). Hb Hd Press the part (Hd) on the part (Hb). Do a final check to make sure that: • All screws are tightened. • The sealing strip is attached tightly to the cabinet. • The door opens and closes correctly. Noises There are some sounds during normal running ([...]

BRRR ! HISSS! CLICK! BLUBB! CRACK! SSSRR R! OK CLICK! CLICK! SSSRRR! SSSRRR! BRRR! BRRR! HISSS! HISSS! BLUBB! BLUBB! CRACK! CRACK! 15 www.zanussi.com[...]

Technical data Dimension of the recess Height 1780 mm Width 560 mm Depth 550 mm Voltage 230-240 V Frequency 50 Hz The technical inform ation are situat ed in the rat- ing plate on the internal left side of the appli- ance and in the energy label. 16 www.zanussi.com[...]

17 www.zanussi.com[...]

18 www.zanussi.com[...]

19 www.zanussi.com[...]

www.zanussi.com/shop 222365861-A-102013[...]