Zanussi ZGL 62 инструкция обслуживания

GAS HOBS ZGL 62 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB[...]

2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low Vo ltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Guide to Use the instructions The following symbols will be found in the text to guide you throughout [...]

3 Content s For the User For the Installer Important Safety Information 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Service and S pare Parts 5 Customer Care Department 6 Guarantee Conditions 6 Engineers technical data 9 Ins tallation 1 0 Important Safety Requirements 1 0 Building In 1 1 Electrical conn[...]

4 Operation Hob Burners To light a burner: l turn the relevant control knob anticlockwise to maximum position; l at the same time push the electric ignition pushbutton which is marked by a little spark; l then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. T o ensure maximum burner efficie[...]

5 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMP[...]

6 Zanussi Guarantee conditions W e , Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditi[...]

7 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale, Guernsey Channel Islands JERSEY Jersey Electricity Comp any PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN 54 Claremont Street (M05) Aberdeen AB10 6 RA [...]

8 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East (M18) Wyrley Road Ind. Est ate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate (M44) Pinfold Road Bourne PE10 9HT BRIDGNORT H 6 8 St. Marys Street (M72) Bridgnorth Shropshire WV16 4DR GLOUCESTER 10[...]

9 BURNER RAPID SEMI-RAPID AUXILIARY (large) (m edium) ( small) POSITION M A X M IN M A X M IN M A X M IN NOMINAL THERMAL POWER k W 3 . 0 0.65 2 .0 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 / h 0.286 0.057 0.190 0.038 0.095 0.028 NOZZLE REFERENCE 1 1 9 A d just. 9 6 Adjust. 7 0 Adjust. NOMINAL THERMAL POWER k W 2 . 8 0.65 2 .0 0.45 1.0 0.33 NOMINAL FLOW R[...]

10 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm FO 0812 FO 0813 Import ant safety requirement s This hob must be inst alled in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contai[...]

11 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Dimensions are given in mm. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to ca[...]

12 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break t[...]

13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A Wiring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance [...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

15 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguishe[...]

CUST OMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705-727727 © Electrolux Household Appliances Limited 2000 Grafiche MDM - Forlì 35675-2601 09/00 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More t[...]