Zanussi ZGP 982 инструкция обслуживания

INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB GAS HOB ZGP 982[...]

2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low Vo ltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Guide to Use the instructions The following symbols will be found in the text to guide you throughout [...]

3 Content s For the User For the Inst aller Import ant Safety Information 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Service and S pare Parts 5 Guarantee Conditions 6 Important Safety Requirements 10 Installation 1 0 Fitting the hob to the worktop 1 1 Electrical connections 12 Wiring Diagram 13 Fault [...]

4 Operation Hob burners To light a burner: l push in the relevant control knob and turn it to maximum position. l Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (Fig. 1 letter C) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. l Then adjust[...]

5 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMP[...]

6 Zanussi Guarantee conditions W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditio[...]

7 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale, Guernsey Channel Islands JERSEY Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN 54 Claremont Street (M05) Aberdeen AB 10 6RA A[...]

8 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East (M18) Wyrley Road Ind. Est ate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate (M44) Pinfold Road Bourne PE10 9HT BRIDGNOR T H 68 St. Mary s Street (M72) Bridgnorth Shropshire WV16 4DR GLOUCESTER 1[...]

9 BURNER RAPID SEMI-RAPID AUXILIARY (large) (m edium) ( small) POSITION M A X MI N M A X M IN M A X MI N M A X MI N NOMINAL THERMAL POW ER k W 3 . 0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 NOMINAL FLOW RATE m 3 /h 0.286 0.062 0.190 0.043 0.095 0.031 0.333 0.114 NOZZLE REFERENCE 1 1 9 A d j u s t . 9 6 A d j u s t . 7 0 A d j u s t . 1 3 6 A d j u s t . NOMI[...]

10 FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 400 mm 100 mm 20 mm 900 mm 700 mm 400 mm 400 mm 100 mm 20 mm 900 mm FO 2540 FO 2541 Import ant safety requirement s This hob must be inst alled in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detaile[...]

11 Carry out the installation of the hob as follows (follow also the instructions given on the Assembly and cut outlines supplied with the appliance): 1 ) measure the worktop for the exact positioning of the hob; 2 ) make the holes for the gas and electric pipe outlet and the safety holes to block the hob to the worktop (follow the instructio[...]

12 A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . Connection to the gas supply can be carried out on the le ft or on the right of the hob connection pipe. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male t[...]

13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A Wiring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance [...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

15 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguishe[...]

CUST OMER CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux Household Appliances Limited 2000 Grafiche MDM - Forlì 35683-4501 09 /00 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More [...]