Zanussi ZHC 913 инструкция обслуживания

COOKER HOOD ZHC 613 ZHC 913 INSTRUCTION BOOKLET[...]

2 Thank you for buying a Zanussi product. T o enable you to use your appliance effectively and safely , please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Depar[...]

3 IMPORT ANT SAFETY INFORMA TION These warnings are provided in the interests of your safety . Ensure that you understand them all before installing or using this appliance. Y our safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Any installation w[...]

4 YOUR APPLIANCE OPERA TING INSTRUCTIONS The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air . Cooker Hood Controls The cooker hood functions are controlled by three switches located to the right on the underside of the hood i[...]

5 To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack. Extraction In [...]

6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleane[...]

7 Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day . To Remove/Replace the Charcoal Filters 1. First remove the metal grea[...]

8 SOMETHING NOT WORKING SERVICE AND SP ARE P ARTS If, having followed these instructions carefully , your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks, the fault p[...]

9 GUARANTEE CONDITIONS We Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage o[...]

10 INST ALLA TION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way . T echnical Information DIMENSIONS HEIGHT OF CANOPY : 24cm HEIGHT OF CHIMNEY : (UPPER SECTION) 40cm (LOWER SECTION) 5 6cm WIDTH OF CANOPY - ZHC 613: 59,8cm WIDTH OF CANOPY - ZHC 913: 89,8cm DEPTH OF CANOPY : 49cm GROSS - ZHC 613:[...]

11 INST ALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Befo[...]

12 A: Built-in Electric Hob: 650mm minimum clearance B: Built-in Gas hob: 700mm minimum clearance C: Slot-in Electric Cooker: 685mm minimum clearance D: Slot-in Gas Cooker: 787mm minimum clearance Hob Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of t[...]

13 4. Draw a horizontal line through the vertical line at X . X is a distance between the centre of the top and bottom fixing holes on the upper chimney stack. Mark the centre positions for the middle bracket fixing screws (3) at 95mm either of the vertical line (screws not supplied) . 5. Drill the holes for the fixing screws using an 8mm masonary [...]

14 V enting The hood is more effective when used in the extraction mode (ducted to the outside). V enting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 125mm (5”). The 120-125mm collar should be fitted onto the ducting spigot to suit UK diameter ducting, and held in position by a jubilee clip ([...]

15 Fitting the Chimney Stack The chimney stack consists of two sections. 1. Fit the upper section (S) first. Expand the chimney slightly to allow it to be fitted over the brackets (1) and (2), and then secure the chimney stack to bracket (2) using two self tapping screws provided in the fitting kit. 2. Fit the lower chimney section (I) by expanding[...]

16[...]

17[...]

18[...]

19[...]

© Electrolux Household Appliances Limited 2000 4329515 04 - 010905[...]