Zenoah BKZ5000DL инструкция обслуживания

GB-1 G B BKZ4500DL / BKZ5000DL BKZ4500DL BKZ5000DL G B OWNER’S MANUAL BRUSHCUTTERS 848KH093A3 (704)[...]

GB-2 BKZ4500DL / BKZ5000DL EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS SOUND LEVEL VIBRA TION LEVEL ISO 10884 LwA measured guaranteed ISO 7916 racing MODEL LpA EN27917 idling BKZ4500DL 45.2 cm 3 99 dB(A) 117 dB(A) 118 dB(A) 0.8 m/s 2 7.2 m/s 2 BKZ5000DL 50.6 cm 3 102 dB(A) 118 dB(A) 120 dB(A) 0.8 m/s 2 7.5 m/s 2 APPRO V AL NUMBER OF CE EXHA UST EM[...]

GB-3 G B BKZ4500DL / BKZ5000DL 1. Par ts location (1) Primer (2) Air cleaner cov er (3) Choke le ver (4) Fuel tank (5) Star ter knob (6) Blade (7) Angle transmission (8) Cutting Attachment guard (9) Loop handle (10) Shaft tube (11) Fle xible shaft (12) Throttle trigger (13) Stop s witch (14) Throttle cable (15) F rame (16) Back cushion SAFETY FIRST[...]

GB-4 BKZ4500DL / BKZ5000DL 2. Specification 4. Symbols on the machine For safe operation and maintenance, symbols are carved in relief on the machine. Accor ding to these indications, please be careful not to make a mistake. The port to refuel the “MIX GASOLINE” P osition: FUEL T ANK CAP The direction to close the choke Position: ENGINE COVER T[...]

GB-5 G B BKZ4500DL / BKZ5000DL 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer fr om whom you purchased t[...]

GB-6 BKZ4500DL / BKZ5000DL BEFORE ST ARTING THE ENGINE 1. The area within a perimeter of 15 m (50 ft) of the person using the product should be consider ed a haz- ardous ar ea into which no one should enter . If necessary , yellow warning r ope, warning signs should be placed around the perimeter of the ar ea. When work is to be perfor med simul- t[...]

GB-7 G B BKZ4500DL / BKZ5000DL • IF SOMEONE COMES 1. Guard against hazar dous situa- tions at all times. W arn adults to keep pets and children away fr om the area. Be car eful if you are ap- proached. Injury may result fr om flying debris. 2. If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the en- gin[...]

GB-8 BKZ4500DL / BKZ5000DL 6. Set up INST ALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that the edge of CE label is matched with the handle. W ARNING • Stop tightening the screws when the gap A be- comes zero. FLEXIBLE SHAFT 1. Remove the bolt located on the joint of the shaft tube. 2. Match the groove of the li[...]

GB-9 G B BKZ4500DL / BKZ5000DL 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container . 3. Pour in all of the oil and agitate well. 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients[...]

GB-10 BKZ4500DL / BKZ5000DL ST ARTING ENGINE W ARNING • The cutting head will start rotating upon the en- gine starts. 1. Feed fuel into the fuel tank and tighten the cap se- curely . 2. Rest the unit on a flat, firm place. Keep the cutting head off the gr ound and clear of surrounding objects, as it will start rotating upon starting of the engin[...]

GB-11 G B BKZ4500DL / BKZ5000DL MET AL BLADE USAGE 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fas- tened according to instruction and the blade turns smoothly without abnormal noise. W ARNING • The rotating parts fastened incorrectly ma y cause serio[...]

GB-12 BKZ4500DL / BKZ5000DL d. Keep the blade sharp. A dull blade increase the chance of bounce. e. A void feeding the blade too rapidly . The blade can bounce away from material being cut if the blade is fed faster than its cutting capability . f. Cut only from your right to your left. g. Keep your path of advance clear of material that has been c[...]

GB-13 G B BKZ4500DL / BKZ5000DL 8. Operation 9. Maintenance Every Every Ever y 25 50 100 System/components Procedur e Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter , fuel filter inspect/clean ✔✔ r eplace, if necessary see adjusting replace carbur etor idle speed adjuster ✔ idl[...]

GB-14 BKZ4500DL / BKZ5000DL AIR FIL TER •T he air filter , if clogged, will reduce the engine per - formance. Check and clean the paper element by air blow as requir ed. If the element becomes dirty , re- place with a new one. (1) FUEL FIL TER • When the engine runs short of fuel supply , check the fuel cap and the fuel filter for blockage. (1)[...]

GB-15 G B BKZ4500DL / BKZ5000DL fler to become overheated and that in turn could cause the engine to catch on fire. Alwa ys make sure that the muffler is c lean and free of w ood c hips, lea ves, and other waste before use. • Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage, [...]

GB-16 BKZ4500DL / BKZ5000DL Limited warranty Should any failure occur on the pr oduct under normal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profession- ally , and 30 days if used for rental pu[...]