Enterasys Networks 2G4082-25 Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 58 Seiten
- 1.46 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Network Router
Enterasys Networks 3000
60 Seiten 1.46 mb -
Network Router
Enterasys Networks RBT-4102
168 Seiten 2.3 mb -
Network Router
Enterasys Networks RBT-1002-EU
56 Seiten 0.53 mb -
Network Router
Enterasys Networks XSR-3020
110 Seiten 2.32 mb -
Network Router
Enterasys Networks RBT-1002C
56 Seiten 0.53 mb -
Network Router
Enterasys Networks XSR-1805
25 Seiten 0.57 mb -
Network Router
Enterasys Networks FN 100
54 Seiten 0.52 mb -
Network Router
Enterasys Networks 1G58x-09
808 Seiten 5.83 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Enterasys Networks 2G4082-25 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Enterasys Networks 2G4082-25, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Enterasys Networks 2G4082-25 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Enterasys Networks 2G4082-25. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Enterasys Networks 2G4082-25 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Enterasys Networks 2G4082-25
- Den Namen des Produzenten und das Produktionsjahr des Geräts Enterasys Networks 2G4082-25
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Enterasys Networks 2G4082-25
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Enterasys Networks 2G4082-25 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Enterasys Networks 2G4082-25 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Enterasys Networks finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Enterasys Networks 2G4082-25 zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Enterasys Networks 2G4082-25, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Enterasys Networks 2G4082-25 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
8.5x11-inch cover with bleed on 4 sides Enterasys Matrix ® DFE-Platinum Series Hardware Installation Guide Module 2G4082-25 P/N 9034310-01[...]
-
Seite 2
[...]
-
Seite 3
i Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web si te without prior notice. The reader should in all cases co nsult Enterasys Netw orks [...]
-
Seite 4
ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device complie s with Par t 15 of the FCC rules. Operation is subject to the following tw o conditions: (1) this device may not cause harmful interference, a[...]
-
Seite 5
iii Electromagnetic Compatibility (EMC) This product complies with the following: 47 CFR Par t s 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN 61000 ‐ 3 ‐ 2, EN 61000 ‐ 3 ‐ 3, EN 55024, AS/NZS CISPR 22, VCCI V ‐ 3. Compatibilidad [...]
-
Seite 6
iv ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 &U ⒈㘨㣃 3%% ⒈Ѡ㣃䝮 3%'( 䞥ሲ䚼ӊ (Metal Parts) hƻ ƻ h ƻ ƻ ⬉䏃ഫ ( Circuit [...]
-
Seite 7
v VCCI Notice This is a class A product based on the standard of the Vo l u n t a r y Contro l Counc il for Interferenc e by Information T echnology Equipment (VCCI). If this equipm ent is used in a domestic environme nt, radi[...]
-
Seite 8
vi Declaration of Conformity Application of Co uncil Directiv e(s): 2004/108/EC 2006/95/EC Manufacturer ’ s Name: Enterasys Networks, Inc. Manufacturer ’ s Address: 50 Minuteman Road Andover , MA 01810 USA European Representative Addre ss: Enterasys Networks, Ltd. Nexus House, Newbury [...]
-
Seite 9
vii shall not be permitted by that applicable law , such rights are expressly excluded. Info rmation necessary to achieve interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasy[...]
-
Seite 10
viii 8. AUDIT RIGHTS. You hereby acknowledge that the intellectual pr operty rights associated with the Program are of critical value to Enterasys, and, accordi ngly, You hereby agree to maintain complete books, records and accoun[...]
-
Seite 11
ix Contents About This Guide Who Should Use This G uide .............. ............. ................ ............. ................ ............. ................ ............. ........... xi How to Use This Guide ............. ................ ............. ................ ............. ................ ............. ..... ..................... [...]
-
Seite 12
x Recommended Shutdown Procedure .......................... ................ ............. ................ ................ ......... ...... 4-6 Last Resort Shutdo wn Procedure ...................... ................. ............. ................ ............. ............ ... ............ 4-6 Appendix A: Specifications DFE-Platinum Module Speci[...]
-
Seite 13
Matrix DFE-Platinum Series Installation Guide xi About This Guide This guide provides an overview , installation and tr oubleshooting instructions, and specifications for the Enterasys Matrix ® DFE ‐ Platinum 2G4082 ‐ 25 module. For information about the CLI ?[...]
-
Seite 14
How to Use This Guide xii About This Guide How to Use This Guide Read through this guide completely to familiarize you rs e lf with its contents and to gain an understanding of the features and capabilities of the DFE module. A general work i[...]
-
Seite 15
Conventions Used in This Guide Matrix DFE-Platinum Series Installation Guide xiii Conventions Used in This Guide The following conventions are used in this guide. Lowercase x: Indicates the general use of an alphanumeric character (for example, 6x1xx, the x’ s [...]
-
Seite 16
Getting Help xiv About This Guide •T h e device history (for example, have you returned the device before, is this a recurring problem) •A n y previous Return Material Authorization (RMA) numbers[...]
-
Seite 17
Matrix DFE-Platinum Series Installation Guide 1-1 1 Introduction This chapter provides an overview of the DFE module capabilities, and introduces the 2G4082 ‐ 25 DFE module. Overview of DFE Series Cap abilities The Platinum Distributed Forw arding Engine (DFE) is [...]
-
Seite 18
DFE-Platinum Module 1-2 Introduction DFE-Platinum Module This section provides an overview of the 2G4082 ‐ 25 DFE module ( Figure 1 ‐ 1 ). For information about features of the DFE ‐ Platinum modules and how to configure them, refer to the [...]
-
Seite 19
DFE-Platinum Module Matrix DFE-Platinum Series Installation Guide 1-3 Figure 1- 1 DFE-Platinum 2G4082-25 Module 1 OFFLINE/RESET switch 6 GROUP st atus LEDs 2 RJ45 COM (Console Port) 7 GROUP selected LEDs 3 CPU LED 8 NEM option slot 4 MGMT LED 9 Ports (1-24) 10/100/1000 Mbps, via 24 RJ45s 5 GROUP SELECT button Â Ã Ä Æ Á À Å È Ç COM OFFL[...]
-
Seite 20
Network Expansion Module (NEM) Option 1-4 Introduction Network Exp ansion Module (NEM) Option The 2G4082 ‐ 25 option slot provides access to an installed network expansion module. Refer to the Enterasys Netw orks web site for a current listing of the ?[...]
-
Seite 21
Secure Networks Policy Support Matrix DFE-Platinum Series Installation Guide 1-5 Secure Networks Policy Support A fundamental concept that is key to the implementation of the Enterasys Secure Networks methodology is policy ‐ enabled networking. This approach provides [...]
-
Seite 22
LANVIEW Diagnostic LEDs 1-6 Introduction[...]
-
Seite 23
Matrix DFE-Platinum Series Installation Guide 2-1 2 Network Requirements This chapter provides information concerning the network requirements that mu st be met to ensure a satisfactory performance from the DFE module. The information consists of the[...]
-
Seite 24
10BASE-T Network 2-2 Network Requirements 10BASE-T Network When connecting a 10BASE ‐ T segment to any of the fixed front panel ports of the 2G4082 ‐ 25, ensure that the network meets the Ether net ne twork requirements of the IEEE 80[...]
-
Seite 25
Matrix DFE-Platinum Series Installation Guide 3-1 3 Installation This chapter provides the instructions to install the DFE ‐ Platinum 2G4082 ‐ 25 module. Follow the order of the sections list ed below to correctly install the module. Electrical Hazard: Only [...]
-
Seite 26
Unpacking the DFE-Platinum Module 3-2 Installation Unp a cking the DFE-Platinum Module Unpack the DFE ‐ Platinum module as follows: 1. Open the box and remov e the packing material protecting the DFE ‐ Platinum module. 2. V erify the contents of the carton a[...]
-
Seite 27
Installing Module into Ma trix E7 or N7 Chassis Matrix DFE-Platinum Series Installation Guide 3-3 Prep aration 1. Remove the blank pan el covering th e module slot in which the module will be installed. All other slots must remain covered to ensure proper ?[...]
-
Seite 28
Installing Module into Matrix E7 or N7 Chassis 3-4 Installation 4. Refer to the Caution note above, then rotate the two lever s into the closed position. 5. If the chassis in which the module is instal led was powe red down for the instal[...]
-
Seite 29
Installing Module into Matrix N1, N3, or N5 Chassis Matrix DFE-Platinum Series Installation Guide 3-5 Inst alling Module into Matrix N1, N3, or N5 Chassis The 2G4082 ‐ 25 can be installed in the single slot of the Matrix N1 chas sis, or any av ailable chassis slot in the [...]
-
Seite 30
Connecting to the Network 3-6 Installation Figure 3-2 Inst alling Module into N3, N1, or N5 Chassis (N3 shown) Connecting to the Network This section provides the procedures for connecting unshielded twi sted pair (UTP) segments from the network or other devices to the [...]
-
Seite 31
Connecting to the Network Matrix DFE-Platinum Series Installation Guide 3-7 Figure 3 ‐ 3 shows connecting a twisted pair segment to the 2G4082 ‐ 25 module. It is assumed that the chassis pow er is turned on to provide powe r to the module. ?[...]
-
Seite 32
Connecting to the Network 3-8 Installation Figure 3-4 Four-W ire Crossove r Cable RJ45 Pinout s, Connections Between Hub Devices Figure 3-5 Four-W ire Straig ht-Through Cable RJ45 Pinout s, Connections Between Switches and End Use r Devices 1 RJ45 device port 3 RJ45-to-RJ45 crossover cable 2 Other device port 4 RX+/RX- and TX+/TX- conn ections. The[...]
-
Seite 33
Connecting to the Network Matrix DFE-Platinum Series Installation Guide 3-9 Figure 3-6 Eight-Wire Crossover Cable RJ45 Pinout s, Connectio ns Between Hub Devices Figure 3-7 Eight-Wire Straight-Throu gh Ca ble RJ45 Pinout s, Connections Between Switches and End-Use r Devices e. Ensure that the twisted pair connection meet s ?[...]
-
Seite 34
Connecting to COM Port for Local Management 3-10 Installation Connecting to COM Port for Local Management This section describes how to install a UTP straight ‐ through cable with RJ45 connectors and optional adapters to connect a PC, a VT series terminal,[...]
-
Seite 35
Connecting to COM Port for Local Management Matrix DFE-Platinum Series Installation Guide 3-11 Figure 3-8 Connecting an IBM PC or Comp atible Connecting to a VT Series T erminal To connect a VT Series terminal to an Enterasys Networks DFE ‐ Pl atinum module COM port ( Figure 3 ‐ 9 ), use ?[...]
-
Seite 36
Connecting to COM Port for Local Management Connecting to Modem 3-12 Installation Figure 3-9 Connecting a VT Series T erminal Connecting to a Modem To connect a modem to an Enterasys Networks DFE ‐ Platinum module COM port ( Figure 3 ‐ 10 ), use a UTP straight ‐ through cable [...]
-
Seite 37
Pin Out Descriptions Connecting to COM Port for Local Management Matrix DFE-Platinum Series Installation Guide 3-13 Figure 3-10 Connec ting to a Modem Adapter Wiring and Signal Assignment s 1 UTP straight-through cable with RJ45 connectors 4 Local modem 2 RJ45 COM port 5 Remote modem 3 RJ45-to-DB25 modem adapter 6 Remote PC Ä Â Ã À Å 2G4082-25[...]
-
Seite 38
Connecting to COM Port for Local Management Pin Out Descriptions 3-14 Installation VT Series Port Adapter W iring and Signal Diagram RJ45 DB25 Pin Conductor Pin Signal 4 Red 2 T ransmit (TX) 1 Blue 3 Receive (RX) 6 Y ell ow 5 Clear to Send (CTS) 5 Green 7 Ground (GRD) 2 Orange 20 Data T erminal Ready Modem Port Adapter W iring and Signal Diagram RJ[...]
-
Seite 39
Pin Out Descriptions Completing the Installation of a New System Matrix DFE-Platinum Series Installation Guide 3-15 Completing the Inst allation of a New System The 2G4082 ‐ 25 becomes the management module on the Matrix chassis pow er up. A complete list of the factory defau[...]
-
Seite 40
Completing the Installation of a New System Pin Out Descriptions 3-16 Installation Figure 3-1 1 Matrix DFE St artup Screen Example (N 7 Chassi s) Logging in with an Administrati vely-Configured User Account If the device’ s default user account settings have been changed, proceed as follows: 1. At ?[...]
-
Seite 41
Matrix DFE-Platinum Series Installation Guide 4-1 4 T roubleshooting This chapter provides information concerning the following: Unless otherwise noted, the following information applies to all DFE modules. Using LANVIEW The modules use a built ‐ in visual dia[...]
-
Seite 42
Using LANVIEW 4-2 Troubleshooting Figure 4-1 LANVIEW LEDs Ta b l e 4 ‐ 1 describes the LED indications and provides recommended actions as appropriate. 1 MGMT LED 2 Group 1, Port 1 LEDs The terms used in T able 4-1 indica te the followin g: • Flashing indicates an LED is flashing randoml y . • Blinking [...]
-
Seite 43
Using LANVIEW Matrix DFE-Platinum Series Installation Guide 4-3 CPU None Power off. Ensure chassis has a dequate power . Amber Blinking . Module in process of booting. None. Solid . T esting. If the LED remains amber for several minutes, contact Enterasys Networks for technical support. Green Blinking . Image start s running. None. Solid . Function[...]
-
Seite 44
Troubleshooting Checklist 4-4 Troubleshooting T roubleshooting Checklist If the module is not work i ng properly , refer to Ta b l e 4 ‐ 2 for a checklist of problems, possible causes, and recommended actions to resolve the problem. T able 4-2 T roubleshoo[...]
-
Seite 45
Overview of DFE-Platinum Module Shutdown Procedure Matrix DFE-Platinum Series Installation Guide 4-5 Overview of DFE-Platinum Module Shut down Procedure The DFE ‐ Plati num module must shut down in an orderly fashion to ensure tha t the other modules in the system and [...]
-
Seite 46
Overview of DFE-Platinum Module Shutdown Procedure 4-6 Troubleshooting Recommended Shut down Procedure Before pulling a DFE ‐ Platinum module out of a chassi s, press or tap on its OFFLINE/RESET switch for less than 1 second. Its CPU LED changes from ?[...]
-
Seite 47
Matrix DFE-Platinum Series Installation Guide A-1 A Specifications This appendix provides information about the foll owing: Enterasys Networks reserves the right to change the specifications at any time without notice. DFE-Platinum Module S pecifications Ta b l e A ‐ 1 pr[...]
-
Seite 48
COM Port Pinout Assignments A-2 Specifications COM Port Pinout Assignment s The COM port is a serial communications port for local access to Local Management. Refer to Ta b l e A ‐ 2 for the COM port pin assignments. Regulatory Compliance The 2G4082 ‐ 25[...]
-
Seite 49
Matrix DFE-Platinum Series Ha rdware Installation Guide B-1 B Mode Switch Bank Settings and Optional Installations This appendix covers the following items: Required T ools Use the following tools to perform the procedures provided in this appendix: •A n t i s t a t i c wrist [...]
-
Seite 50
Memory Locations and Replacement Procedures B-2 Mode Switch Bank Settings and Optional Installations •S w i t c h 8 – Clear Admin Pa s s wo r d . Changing the position of this swi tch clears the admin password, and restores the factory default pas sword on ?[...]
-
Seite 51
Memory Locations and Replacement Procedures Matrix DFE-Platinum Series Ha rdware Installation Guide B-3 Location of Memory Modules Figure B ‐ 2 shows the locations of the DRAM SIMM and DIMM on the main board of the 2G4082 ‐ 25. Figure B-2 Memory Module Locat ions on the 2G4082-25 F[...]
-
Seite 52
Memory Locations and Replacement Procedures B-4 Mode Switch Bank Settings and Optional Installations Figure B-3 NEM Removal and DIMM Connector Location 2. Refer to Figure B ‐ 4 . Push the connector arms aw ay from the DIMM and simultaneously lift the DIMM enough to release ?[...]
-
Seite 53
Memory Locations and Replacement Procedures Matrix DFE-Platinum Series Ha rdware Installation Guide B-5 Inst alling the DIMM To install a DIMM, refer to Figure B ‐ 5 and proceed as follows: 1. Insert the DIMM down between the connector fingers. 2. Pivot the DIMM downw[...]
-
Seite 54
Memory Locations and Replacement Procedures B-6 Mode Switch Bank Settings and Optional Installations DRAM SIMM Replacement Procedure Removing the DRAM SIMM To remove the existing DRAM SIMM, proceed as follows: 1. Locate the DRAM SIMM connector on the main PC board. Refer ba[...]
-
Seite 55
Memory Locations and Replacement Procedures Matrix DFE-Platinum Series Ha rdware Installation Guide B-7 Figure B-7 Inst alli ng the DRAM SIMM 1 DRAM SIMM Connector arms 3 Connector contacts 2 DRAM SIMM 4 DRAM SIMM alignment notches (2) Á Â Ã À Ã À[...]
-
Seite 56
Memory Locations and Replacement Procedures B-8 Mode Switch Bank Settings and Optional Installations[...]
-
Seite 57
Index-1 Index Numerics 1000BASE-SX/LX/ELX network connections requirements for 2-2 1000BASE-T network connections requirements for 2-2 100BASE-TX requirements 2-2 10BASE-T connection 3-6 requirements 2-2 2G4082-25 introduction to 1-2 C Cable connections 2G4082-25 3-6 Cable specifications 1000BASE-SX/LX/ELX network 2-2 1000BASE-T network 2-2 100BASE[...]
-
Seite 58
Index-2[...]