Ford 2010 Ranger Bedienungsanleitung

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 16 Entertainment Systems 19 AM/FM stereo 19 AM/FM Stereo single CD/MP3 system 21 CDX6/MP3 Premium/Audiophile Pioneer system 26 Auxiliary input jack (Line in) 32 Satellite radio information 38 Climate Controls 41 Heater only 41 Manual heating and air conditioning 42 Lights 44 [...]

Seating and Safety Restraints 69 Seating 69 Safety restraints 75 Airbags 90 Child restraints 101 Tires, Wheels and Loading 1 18 T ire information 120 T ire inflation 122 T ire Pressure Monitoring System (TPMS) 135 V ehicle loading 140 T railer towing 147 Recreational towing 157 Driving 159 Starting 159 Brakes 164 AdvanceT rac 威 167 T ransmission [...]

Maintenance and Specifications 232 Engine compartment 234 Engine oil 237 Battery 242 Engine coolant 244 Fuel information 250 Air filter(s) 266 Part numbers 267 Maintenance product specifications and capacities 268 Engine data 272 Accessories 276 Ford Extended Service Plan 278 Index 281 All rights reserved. Reproduction by any means, electronic or m[...]

CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following [...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage. SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’[...]

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Y our vehicle is not equipped with a snowplowing package. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Y our vehicle is not equipped with the Ford Ambulance Preparation Package. DATA RECORDING Service Data Recording Service data recorders in y[...]

• where the driver was positioning the steering wheel; and • longitude and latitude of vehicle at last location, using GPS technology and advanced vehicle sensors. T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder informatio[...]

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the service engine soon indicator to come on. It may take a long period of time for the system to detect an improperly installed or properly re-installed fuel filler cap depending on driving and fuel tank level conditions. Ref[...]

Airbag readiness: If this light fails to illuminate when the ignition is turned to on, continues to flash or remains on, contact your authorized dealer as soon as possible. A chime will sound when there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to remind you[...]

W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. AdvanceT rac 威 /T raction control: Illuminates when the AdvanceT rac 威 /T raction control is active. If the light remains on, contact your authorized dealer as soon as possible. Refer to the Driving chapter for more information. AdvanceT rac 威 /T raction cont[...]

Anti-theft system: Flashes when the SecuriLock 威 Passive Anti-theft System has been activated. Speed control (if equipped): Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay o[...]

Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine a[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on[...]

AUDIO SYSTEMS AM/FM stereo (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell [...]

3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns. 5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T re[...]

AM/FM stereo single CD/MP3 Satellite Compatible system (if equipped) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of t[...]

3. MUTE: Press to mute the playing media. Press again to return to the playing media. 4. MENU: Press MENU repeatedly to scroll through the following modes and use MENU to make an adjustment in those modes. SA TELLITE RADIO MENU (if equipped): Press MENU repeatedly when satellite radio mode is active until SA T MENU is displayed. Press SEEK or prese[...]

would like to delete, press SEEK or preset #6. The song will appear in the display for confirmation. Press SEEK or preset #6 again and the display will read SONG DELETED. If you do not want to delete the currently listed song, press MENU to select either RETURN or CANCEL. Note: If there are no songs presently saved, the display will read NO SONGS. [...]

Flat file/directory mode: In MP3 mode, use MENU to select flat file mode or directory mode. Normal / T rack title / File name: Use / to scroll through MP3 display options (track #, normal music name or file name). 5. TUNE: Press to manually go down/up ( / ) the radio frequency and also to select various settings in menu mode. 6. SHUFF (Shuffle): Pr[...]

11. SEEK/TRACK: Press to access the previous/next ( / ) strong station. In CD/MP3 mode, press to advance to the previous/next ( / ) track. In satellite radio mode (if equipped), press SEEK to seek to the previous/next channel. In CA TEGOR Y MODE, press SEEK to select a channel within that category . Press and hold SEEK to fast seek through the prev[...]

15. ON/OFF/V olume: Press to turn on/off. T urn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16. CD: Press to enter CD/MP3 mode. If a CD is already present in the system, the disc wil[...]

W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The driver’ s primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to[...]

7. MENU: Press MENU repeatedly to cycle through the following modes and use / to make adjustment in those modes. SA TELLITE RADIO MENU (if equipped): Press MENU when satellite radio mode is active to access. Press SEEK to enter into the satellite radio menu. Press / to cycle through the following options: • CA TEGOR Y : Press SEEK or preset #6 to[...]

• DELETE SONG: Press SEEK or preset #6 to delete a song title from the system’ s memory . Press MENU to cycle through the saved songs. When the song title appears in the display that you would like to delete, press SEEK or preset #6. The song will appear in the display for confirmation. Press SEEK or preset #6 again and the display will read SO[...]

Next/previous directory: In MP3 mode, press MENU / to go to the previous/next directory . Flat file/directory mode: In MP3 mode, press MENU to access this feature. Use MENU to select flat file mode or directory mode. T rack #/ normal music name/file name: Press MENU to access and use / to scroll through MP3 display options (track #, normal music na[...]

14. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. T o select a preset station, press the desired memory preset. Y ou can save up to 18 stations, six in AM, six in FM1 and FM2. In satellite radio mode (if equipped), there are 18 available presets, six each for S[...]

Satellite radio is available only with a valid SIRIUS 威 subscription. Check with your authorized dealer for availability . 17. ON/OFF/V olume: Press to turn on/off. T urn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the [...]

Required equipment: 1. Any portable music player designed to be used with headphones 2. An audio extension cable with stereo male 1/8 in. (3.5 mm) connectors at each end T o play your portable music player using the auxiliary input jack: 1. Begin with the vehicle parked and the radio turned off. 2. Ensure that the battery in your portable music pla[...]

5. For safety reasons, connecting or adjusting the settings on your portable music player should not be attempted while the vehicle is moving. Also, the portable music player should be stored in a secure location, such as the center console or the glove box, when the vehicle is in motion. The audio extension cable must be long enough to allow the p[...]

• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not[...]

Operating your audio system with MP3-formatted discs Y our MP3 system recognizes MP3 discs upon insertion and provides you with two ways to listen to these discs: • Flat file mode– This mode ignores any folders on the discs and plays all MP3 files found in any folder on the disc exactly as if there were no folders on the disc. When in flat file[...]

Note: The maximum number of playable MP3 files may be less depending on the structure of the CD and exact model of radio present. • MP3 directory mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001[...]

Satellite radio information (if equipped) Satellite radio channels: SIRIUS 威 broadcasts a variety of music, news, sports, weather , traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS 威 satellite radio channels, visit www .sirius.com in the United States, www .sirius-canada.ca in Canada, or cal[...]

Satellite radio electronic serial number (ESN): This 12–digit Satellite Serial Number is needed to activate, modify or track your satellite radio account. Y ou will need this number when communicating with SIRIUS 威 . While in satellite radio mode, you can view this number on the radio display by pressing the AUX and preset 1 controls simultaneo[...]

Radio Display Condition Action Required NO TEXT Artist information not available. Artist information not available at this time on this channel. The system is working properly . NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category informati[...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outs[...]

4. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selectio[...]

• Remove any snow , ice or leaves from the air intake area at the base of the windshield. During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the A/C in the MAX A/C position, reduce blower fan speed from the highest setting and put the vehicle’ s transmission into the P[...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the low beam headlamps on. Fog lamp control (if equipped) The fog lamps can be turned on when the headlamp control is in the or position and the high beams are not turned on. Pull the headlamp control towards you to[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) The daytime running light system turns the headlamps on with a reduced light output. T o activate: • the ignition must be in the on position and • the headlamp system is in the off position or parking lamp position. W ARNING: [...]

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. This will ensure that your displays are visible under all lighting conditions. AIMING THE HEADLAMPS The headlamps on your vehicle are p[...]

3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it. 5. Locate the vertical adjuster for [...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Courtesy/reading lamps (if equipped) The courtesy lamp lights when: • any door is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed an[...]

Examples of unacceptable moisture (usually caused by a lamp water leak) are: • W ater puddle inside the lamp • Large water droplets, drip marks or streaks present on the interior of the lens T ake your vehicle to dealer for service if any of the above conditions of unacceptable moisture are present. Using the right bulbs Replacement bulbs are s[...]

Replacing interior bulbs Check the operation of all bulbs frequently . Replacing exterior bulbs Check the operation of all the bulbs frequently . Replacing headlamp bulbs/front park bulbs/turn signal bulbs T o remove the bulb(s): 1. Make sure the headlamp switch is in the off position, then open the hood. 2. At the back of the headlamp, pry up the [...]

W ARNING: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order . Replacing front sidemarker bulbs 1. T urn the headlamp s[...]

4. Rotate bulb socket counterclockwise and remove from lamp assembly . 5. Carefully pull bulb straight out of socket and push in the new bulb. 6. Install the bulb socket in lamp assembly by turning clockwise. Install the new bulb in reverse order . Replacing tail lamp/backup lamp bulbs 1. Make sure the headlamp switch is in the off position, then o[...]

3. Rotate bulb socket counterclockwise turn and remove from lamp assembly . 4. Carefully pull the bulb straight out of the socket. Install the new bulb(s) in reverse order . Replacing fog lamp bulbs (if equipped) 1. Make sure the headlamp switch is in the off position and remove the bulb socket from the fog lamp by turning it counterclockwise. 2. D[...]

Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position and reach behind the rear bumper to locate the bulb socket. 2. T wist the socket counterclockwise and remove. 3. Carefully pull the bulb straight out of the socket. Install the new bulb(s) in reverse order . Lights 54 2010 Ranger (ran) Owners Guide, 1st Print[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers (from desired interval to low or high speed position); rotate towards you to decrease the speed of the wipers. W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. [...]

TILT STEERING WHEEL (IF EQUIPPED) T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. W ARNING: Never adjust the steering wheel when the v[...]

Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W . If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for fuse[...]

One-touch down Allows the driver’ s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation. INTERIOR MIRROR The interior rear view mirror has two pivot points on the sup[...]

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal. W ARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or [...]

Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Disengagi[...]

Turning of f speed control T o turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. BEDRAILS (IF EQUIPPED) • This bedrail is for appearance use only . W ARNING: T o help prevent injury , do not use bedrail to retain cargo. • Reta[...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . If your vehicle is equipped with the SecuriLock 威 passive anti-theft system, your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dea[...]

Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to your authorized dealer in order to aid [...]

Note: The panic alarm will only operate when the ignition is in the off position. Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVE[...]

How to reprogram your remote entry transmitters Y ou must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: Ensure the brake pedal is not pressed during this sequence. T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. [...]

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps after several minutes if they are left on accidentally . SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock 威 passive anti-theft system is an engine immobilization[...]

Anti-theft indicator The anti-theft indicator is located in the instrument cluster . V ehicles equipped with the SecuriLock 威 passive anti-theft system behave as follows: • When the ignition is in the off position, the indicator will flash once every two seconds for a total of 10 seconds to indicate the SecuriLock 威 system is functioning as a[...]

1. Insert a previously programmed coded key into the ignition. 2. T urn the ignition from the 3 (off) position to the 4 (on) position. Keep the ignition in the 4 (on) position for at least one second, but no more than 10 seconds. 3. T urn the ignition to the 3 (off) position, and remove the coded key from the ignition. 4. After three seconds but wi[...]

SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W ARNING: Before returning the seatback to its original position[...]

T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that [...]

T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front manual seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: S[...]

Pull lever located at the side of the seat cushion up to adjust seatback. 60/40 seat (if equipped) T o gain access to the storage compartment in your armrest (if equipped), lift the latch to open lid. The 60/40 seat cupholder (if equipped) is detachable for cleaning. • Firmly grasp the bottom of the cup holder and pull up. T o re-attach: • Slid[...]

T o return seat to original position, slide the seat bottom back, then push the seatback up to lock it in place. The seat will lock, and you will have to use the release bar to move the seat back to the original position. REAR SEATS Center facing jump seat (2–door SuperCab) (if equipped) T o open, pull inboard and down on the seat strap. T o stow[...]

SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System™ provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant classifications and conditions and crash severity before activat[...]

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy . A lower , less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints (S[...]

The front passenger sensing system can automatically turn off the passenger front airbag when a rear facing child seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology , parents are STRONGL Y encouraged to always properly restrain children in the rear seat. The sensor also turns off the airbag when the pas[...]

The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, front passenger sensing system, and the driver seat position sensor . In addition, the RCM also monitors the restraints warning light in the ins[...]

W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. W ARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . [...]

2. T o unfasten, press the release button and remove the tongue from the buckle. Lap belts Adjusting the front center seat and rear center facing jump seat lap belts (if equipped) The lap belt does not adjust automatically . W ARNING: The lap belt should fit snugly and as low as possible around the hips, not across the waist. Insert the tongue into[...]

Energy management feature • This vehicle has a safety belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision. • This energy management system has a retractor assembly that is designed to pay out webbing in a controlled manner . This feat[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the a[...]

W ARNING: BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer . W ARNING: Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Safety belt pr[...]

• 2–door SuperCab T o lower the shoulder belt height, press the button and slide the height adjuster down. T o raise the height of the shoulder belt, press the button and slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. W ARNING: Position the safety belt height adjusters so that the belt rests a[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the ve[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during our[...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

The driver and front passenger Belt-Minder 威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • the gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission) • The ignition switch is in the off positio[...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts. Airbags alon[...]

W ARNING: Rear facing child seats should NEVER be placed in front of an active airbag. W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided. W ARNING: National Highway T raffic Safety Administration (NHTSA) recommends a mini[...]

W ARNING: Do not attempt to service, repair , or modify the Airbag Supplemental Restraint System or its fuses. Contact your authorized dealer as soon as possible. W ARNING: The front passenger airbag is not designed to offer protection to an occupant in the center front seating position. W ARNING: Modifying or adding equipment to the front end of t[...]

W ARNING: Front seating positions only: If seating two adults and a child, Ford recommends properly restraining the child in the center front seating position, but only if doing so will not interfere with driving the vehicle. This arrangement provides lap and shoulder belt and airbag protection for adult occupants and an attachment method for a chi[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor V ehicle Safety Standard (FMVSS) 208 and is designed to turn off the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat, • the system determines that a small child is pr[...]

The front passenger sensing system is designed to enable (may inflate) the right front passenger’ s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the indicator will be unlit and stay unlit to remind you t[...]

In case there is a problem with the passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. Do NOT attempt to repair or service the system; take your vehicle immediately to the dealer . W ARNING: The front passenger airbag is not designed to offer protection to an occupant in the center seating position. W ARNIN[...]

Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness in the Instrument Cluster chapter . Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readin[...]

W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking [...]

W ARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase th[...]

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device [...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Small children Children who have outgrown or no[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lower anchors and top tether anchor) Safety belt only Rear facing [...]

W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age. Follow the child restraint manufacturer’ s instructions and warnings provided for installation and use in conjunction with the ins[...]

training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle. T o locate a child seat fitting station[...]

Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be sea[...]

1. Position the child safety seat in a seat with a combination lap and shoulder belt. W ARNING: Rear facing child seats should NEVER be placed in front of an active airbag. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue throug[...]

4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downwa[...]

9. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter . 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to [...]

Attaching child safety seats with LA TCH (Lower Anchors and T ethers for CHildren) attachments The LA TCH system is composed of three vehicle anchor points: two (2) lower anchors located where the vehicle seat back and seat cushion meet (called the “seat bight”) and one (1) top tether anchor located behind that seating position. Y our vehicle i[...]

• 60/40 seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat has been installed using the safety belt, you can attach the top tether strap. Perform the following steps to install a child safety se[...]

The tether anchor is located on the rear lower portion of the passenger seat. 3. Clip the tether strap to the anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. Seating and Safety Restraints 112 2010 Ranger (ran) Owners Guide, 1st Printing USA (fus)[...]

Center seating location When installing a child safety seat in the front center position, route the tether strap over the center arm rest and clip it to the center anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 4. T ighten the child safety seat tether strap accor[...]

Keep your child in the child safety seat if it properly fits the child, remains appropriate for their weight, height and age AND if properly secured to the vehicle. Although the lap/shoulder belt will provide some protection, children who have outgrown a typical child seat are still too small for lap/shoulder belts to fit properly , and wearing an [...]

T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head [...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon t[...]

Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of man[...]

Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended[...]

When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or T ire Label. T o check th[...]

TIRE CARE Inspecting your tires and wheel valve stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve [...]

W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear . However , heat caused by hot climates or frequent high loadi[...]

W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the T ire Label which is locate[...]

It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your T ire Pressure Moni[...]

vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically . Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer . Front wheel drive (FWD) vehicles and those wi[...]

Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire/wheel it is intended for temporary use only and should not be used in a tire rotation. Note: [...]

5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry . Y ou may find this information in your Owner’ s Guide. If not, contact a local tire [...]

numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability . This information is used to contact customers if a tire defect requires a re[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA)[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The[...]

Understanding your Tire Pressure Monitoring System (TPMS) The T ire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low T ire Pressure W arning Lamp will turn ON if the tire pressure is significantly low . Once the light is illuminated, your tires are under inflated and [...]

When you believe your system is not operating properly The main function of the T ire Pressure Monitoring System is to warn you when your tires need air . It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System:[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

SNOW TIRES AND CHAINS W ARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel n[...]

Base Curb W eight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment. V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires,[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . Tires, Wheels and Loading 144 2010 Ranger (ran) Owners Guide, 1s[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.” on your vehicle’ s placard. 2. Determine the combined weight of[...]

to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 [...]

Regular Cab Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum trailer weight - lb (kg) Short Wheel Base 2.3L w/manual transmission 3.73 4800 (2177) 1540 (698) 2.3L w/automatic transmission 4.10 5500 (2495) 2200 (998) Long Wheel Base 2.3L w/manual transmission 3.73 4800 (2177) 1500 (680) 2.3L w/automatic transmission 4.10 5500 (2495) 2160 (980) [...]

SuperCab 4x2 Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum trailer weight - lb (kg) 4–Door Payload Package 1 without Jump Seat 2.3L w/manual transmission 4.10 4800 (2177) 1260 (572) 2.3L w/automatic transmission 4.10 5500 (2495) 1920 (871) 4.0L w/manual transmission 3.55 7000 (3175) 3260 (1479) 4.0L w/automatic transmission 3.55 9500 (430[...]

SuperCab 4x2 Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum trailer weight - lb (kg) 2–Door Payload Package 2 without Jump Seat 4.0L w/manual transmission 3.55 7000 (3175) 3320 (1506) 4.0L w/automatic transmission 3.55 9500 (4309) 5780 (2622) 4–Door Payload Package 2 without Jump Seat 4.0L w/manual transmission 3.55 7000 (3175) 3240 (147[...]

SuperCab 4x2 Sport Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum trailer weight - lb (kg) 4–Door Payload Package 1 without Jump Seat 4.0L w/manual transmission 3.55 7000 (3175) 3160 (1433) 4.0L w/automatic transmission 3.55 9500 (4309) 5620 (2549) 2–Door Payload Package 1 with Jump Seat 4.0L w/manual transmission 3.55 7000 (3175) 3220 ([...]

SuperCab 4x4 Engine Rear axle ratio Maximum GCWR - lb (kg) Maximum trailer weight - lb (kg) 2–Door with Jump Seat 4.0L w/manual transmission All 7000 (3175) 3080 (1397) 4.0L w/automatic transmission All 9500 (4309) 5540 (2513) 4–Door with Jump Seat 4.0L w/manual transmission All 7000 (3175) 3000 (1361) 4.0L w/automatic transmission All 9500 (43[...]

Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. Contact your authorized dealer or a reliable trailer dealer as soon as possible if you require assistance. Hitches For towing trailers up to 2,000 lb (907 kg), use a weight carrying hitch and ball which uniformly distributes the tra[...]

T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Contact your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Using a step bumper (if equipped) The optional step bumper is equipped [...]

Refer to the following chart for information regarding the factory-equipped trailer tow connector: T railer tow connector Color Function Comment 1. Dark Green T railer right-hand turn signal Circuit activated when brake pedal is pressed or when ignition is on and right-hand turn signal is applied. 2. Y ellow T railer left-hand turn signal Circuit a[...]

• Anticipate stops and brake gradually . • Do not exceed the GCWR rating or transmission damage may occur . Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your scheduled maintenance information for more information. T railer towing tips • Practice turning, st[...]

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repa[...]

4WD automatic transmission vehicles with electronic shift transfer case (Neutral tow kit accessory): On vehicles equipped with 4WD, an accessory is available that allows you to tow your vehicle, behind another vehicle, with all the wheels on the ground. Contact your authorized dealer for more details. Do not tow your vehicle with all wheels on the [...]

STARTING Positions of the ignition 1. Accessory — allows the electrical accessories such as the radio to operate while the engine is not running. 2. Lock — locks the steering wheel, automatic transmission gearshift lever and allows key removal. For vehicles equipped with a manual transmission, you must press the ignition release lever to releas[...]

W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. W ARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately [...]

If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Press and hold the clutch pedal to the floor , then put the gearshift lever in the N (Neutral) position. 3. T urn the key to 4 (on) without turning the key to 5 (start). If there is difficulty in turning the key , firmly rotate the steering wheel left and [...]

1. T urn the key to 4 (on) without turning the key to 5 (start). If there is difficulty in turning the key , rotate the steering wheel until the key turns freely . This condition may occur when: • the front wheels are turned • a front wheel is against the curb 2. T urn the key to 5 (start), then release the key as soon as the engine starts. Exc[...]

W ARNING: Failure to follow engine block heater instructions could result in property damage or physical injury . W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater , follow these recommendations for proper and safe op[...]

• Finally , have the engine block heater system checked during your fall tune-up to be sure it’ s in good working order . How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater will use .4 t[...]

The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency . The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking wit[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released. W ARNING: Always set the parking brake f[...]

ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC 姞 ) STABILITY ENHANCEMENT SYSTEM W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the Advanc[...]

• Electronic stability control (ESC), which functions to help avoid skids or lateral slides • Roll Stability Control™ (RSC 威 ), which functions to help avoid a vehicle roll-over . The AdvanceT rac 威 with RSC 威 system automatically enables each time the engine is started. All features of the AdvanceT rac 威 with RSC 威 system (TCS, ESC[...]

Excessive wheel spin is controlled in two ways, which may work separately or in tandem: engine traction control and brake traction control. Engine traction control works to limit drive-wheel spin by momentarily reducing engine power . Brake traction control works to limit wheel spin by momentarily applying the brakes to the wheel that is slipping. [...]

The ESC system may be deactivated in certain situations. See the Switching off AdvanceT rac 威 with RSC 威 section following. Roll Stability Control™ (RSC 威 ) Roll Stability Control™ (RSC 威 ) may help to maintain roll stability of the vehicle during adverse maneuvers. RSC 威 operates by detecting the vehicle’ s roll motion and the rate[...]

AdvanceT rac 威 Features Button functions icon status RSC 威 ESC TCS Default at start-up Illuminated during bulb check Enabled Enabled Enabled Button pressed momentarily Illuminated solid Enabled Enabled Disabled Button pressed and held more than 5 seconds (speed under 35 mph) Flashes then illuminated solid Disabled Disabled Disabled Button press[...]

If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A hi[...]

BRAKE-SHIFT INTERLOCK The vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal pressed, it is possible that a fuse has blown or the vehicl[...]

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or rep[...]

D (Drive) with Overdrive The normal driving position for the best fuel economy . T ransmission operates in gears one through five. D (Drive) without Overdrive D (Drive) with Overdrive can be deactivated by pressing the transmission control switch on the end of the gearshift lever . • This position allows for all forward gears except overdrive. ?[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that prevents cranking the engine unless the clutch pedal is fully pressed. T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press and hold the clutch pedal to the floor , then put the gearshift lever in the neutr[...]

Recommended shift speeds Upshift and downshift according to the following charts: Upshifts when accelerating (for best fuel economy) Shift from: T ransfer case position (if equipped) 2H or 4H 4L 1 - 2 10 mph (14 km/h) 4 mph (5 km/h) 2 - 3 22 mph (32 km/h) 9 mph (11 km/h) 3 - 4 33 mph (50 km/h) 13 mph (19 km/h) 4 - 5 (Overdrive) 41 mph (71 km/h) 17 [...]

This is a lockout feature that protects the transmission from accidentally being shifted into R (Reverse) from 5 (Overdrive). Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. T urn the ignition off. W ARNING: Do not park your vehicle in Neutral, it may move [...]

If equipped with the Electronic Shift 4WD System, and 4WD Low is selected while the vehicle is moving above 3 mph (5 km/h), the 4WD system will not engage. This is normal and should be no reason for concern. Refer to Shifting to/from 4L (4WD Low) for proper operation. 4WD system indicator lights • 4x4 - Momentarily illuminates when the vehicle is[...]

2. On vehicles equipped with an automatic transmission, place the transmission in N (Neutral); on vehicles equipped with a manual transmission, press the clutch. 3. Move the 4WD control to the desired position. • If shifting into 4L (4WD Low), wait for the 4WD LOW light in the instrument cluster to turn on indicating the shift is complete. • If[...]

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or sh[...]

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more. Additionally , smooth variations of [...]

Normal characteristics On some 4WD models, the initial shift from two-wheel drive to 4x4 while the vehicle is moving can cause some momentary clunk and ratcheting sounds. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. A void reducing the tire pressures but shift to a lower gear and drive steadily throu[...]

“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treadin[...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t tu[...]

W ARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously . Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death. If the rear end of the vehicle slide[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadsi[...]

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arranty’ s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our webs[...]

Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. The fuel pump shut-off switch is located o[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Instrument panel dimmer switch 2 10A T railer tow park lamps 3 10A Right low beam headlamp 4 10A Left low beam headlamp 5 5A Windshield wiper module (RUN/ACCY) 6 10A Radio (RUN/ACCY), Door switch illumination 7 — Not used 8 10A Re[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 9 5A Cluster air bag indicator 10 10A Cluster (RUN/ST ART), 4x4 module (RUN/ST ART) 11 10A Passenger compartment fuse panel (Logic power) 12 15A Satellite radio 13 15A Horn, Interior lamps 14 15A High beam headlamp, High beam indicator (cluster) 15 — Not used 16 30A [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 31 20A Front park lamps, Rear park lamps, License plate lamps, Dimmer switch, T railer tow park lamps 32 5A Brake switch (logic) 33 5A Instrument cluster battery feed (B+) 34 20A Power point 35 15A Power locks Power distribution box The power distribution box is locate[...]

2.3L engine (if equipped) The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 40A** Passenger compartment fuse panel 2 — Not used 3 40A** Passenger compartment fuse panel 4 — Not used 5 50A** Passenger compartment fuse panel 6 — Not used 7 30A** Starter solenoid 8 — Not used [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 12 — Not used 13 30A** Blower motor (climate control) 14 — Not used 15 — Not used 16 — Not used 17 40A** Anti-lock brake system (ABS) module 18 — Not used 19 20A** Engine fan 20 — Not used 21 10A* PCM keep alive power , Canister purge valve solenoid 22 — Not used 2[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 40 — Not used 41 10A* Automatic transmission 42 7.5A* T railer tow (left turn) 43 20A* Engine fan relay coil, A/C relay coil, IAC, Mass air flow sensor , Heated exhaust gas oxygen sensor , Catalyst module sensor , V apor management valve solenoid 44 15A* Ignition coil, Capacit[...]

4.0L engines (if equipped) The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 40A** Passenger compartment fuse panel 2 — Not used 3 40A** Passenger compartment fuse panel 4 — Not used 5 50A** Passenger compartment fuse panel 6 — Not used 7 30A** Starter solenoid 8 — Not used 9 40A** Ignitio[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 12 — Not used 13 30A** Blower motor (climate control) 14 — Not used 15 — Not used 16 — Not used 17 40A** Anti-lock brake system (ABS) module 18 — Not used 19 — Not used 20 — Not used 21 10A* PCM keep alive power , Canister purge valve solenoid 22 — Not used 23 30A* Fuel pump mot[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 41 10A* Automatic transmission 42 7.5A* T railer tow (left turn) 43 20A* A/C relay coil, IAC, Mass air flow sensor , Heated exhaust gas oxygen sensor , Catalyst module sensor , V apor management valve solenoid, EGR solenoid, Heated PCV 44 15A* Ignition coil, Capacitor 45A — Not used 45B — N[...]

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. T o restore the full[...]

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T -type mini-spare: This spare tire begins with the letter “T” for tire size and may have “T emporary Use Only” molded in the sidewall 2. Full-size dissimilar s[...]

The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability • All-Wheel driving capability (if applicable) • Load leveling ad[...]

The spare tire and tools for your vehicle are stowed in the following locations: T ool Location Spare tire Under the vehicle, just forward of the rear bumper Jack, jack handle, wheel nut wrench Regular Cab: behind the passenger seat, underneath the jack and tools cover on the floor SuperCab: stowed in the passenger side rear cab under the plastic t[...]

• One wheel nut wrench. Press the button and slide together . 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the square end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward mo[...]

5. W ith the spare tire on the ground, remove the retainer from the spare tire. If equipped with a tether , perform the following additional steps: 6. Lift the spare tire on end to access tether attachment. 7. Use the lug wrench to remove the lug nut from the spare tire tether . 8. If not replacing the spare or flat tire to the underbody storage ar[...]

W ARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block the diagonally opposite wheel. 2. Insert tapered end o[...]

• Rear W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the differential as a jacking point. 5. Remove the wheel lug nuts with the lug wrench. 6. Replace [...]

Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. If you are stowing a tire that requires reattaching it to the vehicle with a tether , perform these steps first, then proceed with the steps following. 1. Place the tire on end with the valve stem facing rearward[...]

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Lug nut socket size/Bolt size Wheel lug nut torque* lb.ft. N • m Lug nut socket size: 3 ⁄ 4 inch (19 mm) hex Bolt size: 1 ⁄ 2 x2 0 100 135 * T orque specifications[...]

W ARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability . Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Preparing your vehicle When the[...]

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the neg[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. W ARNING: Do not connect[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • V ehicle is facing forward so that it is be[...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the c[...]

The CAMV AP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMV AP program, impartial third-party arbitrators conduct h[...]

If you are in another foreign country , contact the nearest authorized dealer . If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • [...]

• After polishing chrome bumpers, apply a coating of Motorcraft 威 Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft 威 Premium Liquid W ax (ZC-53-A), [...]

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine bl[...]

4.0L V6 ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42). WINDOWS AND WIPER BLADES The wi[...]

• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a ne[...]

4. Remove the soaked cloth, and if it is not soiled badly , use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil[...]

UNDERBODY Flush the complete underside of your vehicle frequently . Keep body and door drain holes free from packed dirt. FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically enginee[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Customer Information Guide to find out which parts and servi[...]

2. Block the wheels. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2.[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. W indshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. T ransmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. P[...]

4.0L V6 engine 1. W indshield washer fluid reservoir 2. T ransmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (manual transmission) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11. Engine coolant reser[...]

WINDSHIELD WASHER FLUID • 2.3L engine • 4.0L engine Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause [...]

W asher fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’ s paint finish, wiper blades or washer system. W ARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure to use washer fluid with an[...]

2. T urn the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level dipstick. • 2.3L [...]

• If the oil level is below the lower hole or the MIN mark, add enough oil to raise the level between the two holes or between the MIN-MAX range. • 2.3L I4 engine • 4.0L V6 engine • Oil levels above the upper hole or MAX mark may cause engine damage. Some oil must be removed from the engine by an authorized dealer . Maintenance and Specific[...]

7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour t[...]

Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty . Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are de[...]

Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft 威 oil filter or another with equ[...]

W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. W ARNING: When lifting a plastic-cased battery , excessive pr[...]

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is [...]

Y our vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly . A 50/50 mixture of coolant and water provides the following: • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265?[...]

• 4.0L engine When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level or within the COLD FILL RANGE as listed on the engine coolant reservoir (depending upon application). • Refer to the scheduled maintenance information for service interval schedules. • Be sure[...]

W ARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. W ARNING: Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it dif[...]

W ARNING: T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly . Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Befor[...]

Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Maintenance product specifications and capacities in this chapter . Fill y[...]

FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft 威 part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft 威 fuel filter [...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

the check fuel cap light to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by city and highway driving. Continuing to drive with the check fuel cap light on may cause the service engine soon light to turn on as well. If you must replace the fuel filler cap, replace it with a fuel fil[...]

Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may not be covered under warranty . Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality , per the recommendations in the Choosing the right fuel section. Octane recommendati[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally , adding 1 gallon (3.8L) of fuel is enough to restart the engine. If the vehicl[...]

• Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same[...]

• Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h[...]

• Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four -wheel[...]

W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the service engine soon indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of e[...]

4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the service engine soon indi[...]

The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop[...]

2. While the engine idles, turn the steering wheel left and right several times. 3. T urn the engine off. 4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5. If the fluid is low , add fluid in small amounts, until it reaches between the MIN and MAX lines. Ref[...]

1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir . T RANSMISSION FLUID Checking automatic transmission fluid • Refer to scheduled[...]

9. If necessary , add fluid in 1/2 pint (250ml) increments through the filler tube until the level is correct at normal operating temperatures. Refer to the Maintenance product specifications and capacities section in this chapter for the correct fluid type. The use of any other non-approved fluid may cause internal transmission damage. 10. Fluid c[...]

3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter . T RANSF[...]

DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Y our vehicle is equipped with universal joints that do not require lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, periodic lubrication will be necessary . AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for c[...]

6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. Note: [...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name or equivalent Ford part number / Ford specification Brake fluid and (clutch fluid–if equipped) Between MIN/MAX on brake fluid reservoir and to the line or step on clutch fluid reservoir Motorcraft 威 High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62[...]

Item Capacity Ford part name or equivalent Ford part number / Ford specification Engine coolant (2.3L engine with manual transmission) 10.5 quarts (10.0L) Motorcraft 威 Premium Gold Engine Coolant with bittering agent (yellow-colored) 1 VC-7-B / WSS-M97B51-A1 Engine coolant (2.3L engine with automatic transmission) 10.2 quarts (9.7L) Engine coolan[...]

Item Capacity Ford part name or equivalent Ford part number / Ford specification Automatic transmission fluid (4X2 vehicles with 2.3L engine) 9.9 quarts (9.4L) 3 Motorcraft 威 MERCON 威 VA T F 4 XT -5-QM / MERCON 威 V Automatic transmission fluid (4X2 vehicles with 4.0L engine) 10.0 quarts (9.5L) 3 Automatic transmission fluid (4X4 vehicles with[...]

Item Capacity Ford part name or equivalent Ford part number / Ford specification W indshield washer fluid 2.75 quarts (2.6L) Motorcraft 威 Premium W indshield W asher Concentrate ZC-32-A / WSB-M8B16-A2 Fuel tank–Regular cab (short wheel base) 17 gallons (64.4L) —— Fuel tank–Regular cab (long wheel base) 20.3 gallons (76.8L) —— Fuel tan[...]

ENGINE DATA Engine 2.3L I4 engine 4.0L V6 engine Cubic inches 138 245 Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system EDIS EDIS Spark plug gap 0.049–0.053 inch (1.25–1.35 mm) 0.052–0.056 inch (1.32–1.42 mm) Compression ratio 9.7:1 9.7:1 Engine drivebelt routing • 2.3L I4 engine with A/C • 2.3L I4 engin[...]

• 4.0L V6 engine with A/C • 4.0L V6 engine without A/C Maintenance and Specifications 273 2010 Ranger (ran) Owners Guide, 1st Printing USA (fus)[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSIO[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Lifestyle Ash cup / smoker’ s package Bed products Cargo organization and management T railer hitches, wiring harnesses and accessories T ripT unes™ Advanced portable audio connection Peace of mind Keyless entry keypad Remote start V ehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when[...]

FORD ESP EXTENDED SERVICE PLANS More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Components There [...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 280 2010 Ranger (ran) Owners Guide, 1st Printing USA (fus)[...]

A ABS (see Brakes) ..................... 164 AdvanceT rac .............................. 167 Air cleaner filter ............... 266–267 Airbag supplemental restraint system ....................................90, 98 and child safety seats .............. 92 description ..........................90, 98 disposal .................................... [...]

wheels ...................................... 226 wiper blades ............................ 228 Clock adjust AM/FM ....................................... 20 AM/FM stereo CD ..................... 21 Premium AM/FM stereo CD6/MP3 ................................... 27 Clutch fluid .......................................... 262 operation while driving[...]

preparing to drive your vehicle ..................................... 172 Fuel ............................................ 250 calculating fuel economy ....... 255 cap ........................................... 252 capacity ................................... 268 choosing the right fuel ........... 253 comparisons with EP A fuel economy estimates[...]

instrument panel, dimming ..... 45 interior lamps .....................48, 50 replacing bulbs .........................50 LA TCH anchors ......................... 110 Lights, warning and indicator .... 12 anti-lock brakes (ABS) .......... 165 Load limits ................................. 140 Loading instructions ................. 147 Locks doors ..[...]

for adults ....................... 79, 81–82 for children ............................. 101 lap belt ...................................... 80 Occupant Classification Sensor ........................................ 76 safety belt maintenance ......... 117 warning light and chime .... 84–85 Safety restraints - LA TCH anchors ....................[...]

camper bodies ........................ 158 V entilating your vehicle ........... 162 W W arning lights (see Lights) .......12 W asher fluid .............................. 236 W ater , Driving through ............. 187 W indows power ......................................... 57 W indshield washer fluid and wipers ....................................[...]