Deutsch dropdown-ico

Hearth and Home Technologies GARNET-D-CSB Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Hearth and Home Technologies GARNET-D-CSB an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Hearth and Home Technologies GARNET-D-CSB, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Hearth and Home Technologies GARNET-D-CSB die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Hearth and Home Technologies GARNET-D-CSB. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Hearth and Home Technologies GARNET-D-CSB sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Hearth and Home Technologies GARNET-D-CSB
- Den Namen des Produzenten und das Produktionsjahr des Geräts Hearth and Home Technologies GARNET-D-CSB
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Hearth and Home Technologies GARNET-D-CSB
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Hearth and Home Technologies GARNET-D-CSB zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Hearth and Home Technologies GARNET-D-CSB und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Hearth and Home Technologies finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Hearth and Home Technologies GARNET-D-CSB zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Hearth and Home Technologies GARNET-D-CSB, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Hearth and Home Technologies GARNET-D-CSB widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    www .quadrafire.com September 1, 2008 R GARNET -T DIRECT VENT ROOM HEA TER Owner ’ s Manual Installation and Operation Model: 7016-127F GARNET -MBK GARNET -D-MBK GARNET -D-PMH GARNET -D-CSB GARNET -D-CWL O-T L T ested and Listed by Portland Oregon USA OMNI-T est Laboratories, Inc. C US DO NOT DISCARD THIS MANUAL CAUTION • Important operating a[...]

  • Seite 2

    Page 2 Quadra-Fire · Garnet-T · 7016-127F September 1, 2008 and Welcome to the Quadra-Fire Family ! Hearth & Home T echnologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality , durability , and performance. This commitment begins with our research of the market[...]

  • Seite 3

    Page 3 Quadra-Fire · Garnet-T · 7016-127F - T ABLE OF CONTENTS - September 1, 2008 Section 1: Listing and Code Approvals A. Appliance Certifications ...................... 4 B. Glass Specifications ............................ 4 C. BTU Specifications .............................. 4 D. High Altitude Installations .................... 4 E. Non-[...]

  • Seite 4

    Page 4 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 1 Listing and Code Approvals The product is listed to ANSI standards for “V ented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recre- ational V ehicles” and "Gas Fired Appliances for use at High Altitudes".[...]

  • Seite 5

    September 1, 2008 Page 5 Quadra-Fire · Garnet-T · 7016-127F NOTE: The following requirements reference various Massachusetts and national codes not contained in this document. For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including t[...]

  • Seite 6

    Page 6 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 2 Getting Started Check building codes prior to installation. • Installation MUST comply with local, regional, state and national codes and regulations. • Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and perm[...]

  • Seite 7

    September 1, 2008 Page 7 Quadra-Fire · Garnet-T · 7016-127F 3 Appliance Location and Clearances A. Selecting Appliance Location NOTE: · Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONL Y . · Illustrations/diagrams are not drawn to scale. · Actual installation may vary due to individual design preference. When select[...]

  • Seite 8

    Page 8 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 4 T ermination Locations A. V ent T ermination Minimum Clearances Gas T ermination Wood & Fuel Oil T ermination Comments A 6 in. 20 in. min. Horizontal distance between terminations B 20 in. 24 in. min. Distance to perpendicular wall C 18 in. 18 in. V ertical distance between termina[...]

  • Seite 9

    September 1, 2008 Page 9 Quadra-Fire · Garnet-T · 7016-127F Figure 4.4 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED A = 12 inche s ............. clearances above grade , veran- da, porch, deck or balcony B = 1 2 i n ch es ............ clearances to window or door that may be opened, or to per- manently closed win[...]

  • Seite 10

    Page 10 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 5 V ent Information A. V enting Components B. Use of Elbows In order to comply with applicable codes and product warranties, use only following venting components: • Hearth & Home T echnologies (HHT) • Simpson Dura-V ent • Selkirk Direct-T emp • Amerivent Direct • Security[...]

  • Seite 11

    September 1, 2008 Page 1 1 Quadra-Fire · Garnet-T · 7016-127F D. How to Use the V ent Graph E. V enting Guidelines Figure 5.2 VERTICAL DIST ANCE FROM APPLIANCE TO 90° ELBOW EXCEPTIONS FOR HORIZONT AL INST ALLA TIONS: T he maximum horizontal vent run is 30 in. (762mm). The maximum horizontal vent run with a 45° elbow is 18 in. (457mm). No extern[...]

  • Seite 12

    Page 12 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Female Locking Lugs Male Locking Lugs Step 1. Determine the desired location of the appliance. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance. F . Horizonta[...]

  • Seite 13

    September 1, 2008 Page 13 Quadra-Fire · Garnet-T · 7016-127F NOTE: (1) Installation requires a minimum of 6 in. (152mm) horizontal run of vent with a 1/4 in. (6mm) rise run towards the termination. Each 1 ft. (305mm) of horizontal venting must include a 1/4 in. (6mm) rise. Never allow the vent to run downward. This could cause high temperatures a[...]

  • Seite 14

    Page 14 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Fold Strap Here Wall Thimble Cover/Ceiling Firestop as Required by Local Jurisdiction 1/4 in. (6mm) Strap Sheet Metal Screw Wall Thimble Figure 5.9 WALL THIMBLE COVER WALL THIMBLE Vinyl siding standoff with siding beneath removed SCREWS Bolt horizontal top to vinyl standoff SCREWS Apply[...]

  • Seite 15

    September 1, 2008 Page 15 Quadra-Fire · Garnet-T · 7016-127F Step 1. Check the installation instructions for required 1 in. (25mm) clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. See page 17, Figure 5.16. Check the instructions below for maximum v[...]

  • Seite 16

    Page 16 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Step 4. Assemble the desired lengths of pipe and elbows necessary to reach from the appliance up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-locked position. Assemble as instructed. Step 5. Cut a hole in the roof centered on the sma[...]

  • Seite 17

    September 1, 2008 Page 17 Quadra-Fire · Garnet-T · 7016-127F Step 8. Slip the storm collar over the pipe, and push it down to the top of the flashing ( Figure 5.15 ). Use non-hardening sealant above and below the joint between the storm collar and the pipe. Optional High Wind T ermination Cap Secure Flashing with Non-Hardening Sealant and Roofing[...]

  • Seite 18

    Page 18 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 2. Cathedral Ceiling Level Cathedral Ceiling Support Box 2 in. (51mm) Min. below finished ceiling Cut hole 1/8 in. (3mm) greater in size than pattern of support box as it is projected onto roof line Figure 5.17 Figure 5.18 Step 1. Follow installation Steps 1 and 2 under vertical install[...]

  • Seite 19

    September 1, 2008 Page 19 Quadra-Fire · Garnet-T · 7016-127F High Wind T ermination Cap Sheet Metal Screws Drill Four 1/8 in. (3mm) Diamater Holes Figure 5.22 Figure 5.23 Step 4. Pass the flex pipe down through the center of the chimney system, and center the top adapter on the top of the chimney pipe. Drill four 1/8 in. (3mm) diameter holes thro[...]

  • Seite 20

    Page 20 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 4. Existing Masonry Chimney Figure 5.24 T ype C - Up & Out Installation T ype A & B - Co-Axial to Co-Linear Chimney Liner T ermination Cap Co-Axial to Co-Linear Connector 25 ft. (8m) of 3 in. (76mm) Flex Liner Exhaust Section Pipe Length Optional 4 ft. (1m) of 3 in. (76mm) Flex [...]

  • Seite 21

    September 1, 2008 Page 21 Quadra-Fire · Garnet-T · 7016-127F 10 in. x 10 in. (254mm x 254mm) framed opening in wall Studwall Masonry Chimney Retro Connector (4) Masonry Bolts (Not Included) Wa ll Thimble Cover Figure 5.25 Step 1. Before cutting any holes, assemble the desired sections of direct vent pipe to determine the center of the masonry pen[...]

  • Seite 22

    Page 22 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F High Wind T ermination Cap T op Adaptor (3) Sheet Metal Screws Flashing Step 9. Attach the flex to the retro connector. Use three sheet metal screws to attach the flex liner to the connector ( Figure 5.29 ). Mount the retro connector to the masonry wall using masonry bolts. Redrill larg[...]

  • Seite 23

    September 1, 2008 Page 23 Quadra-Fire · Garnet-T · 7016-127F 3/4 3/4 3/4 BEFORE YOU BEGIN: Review the venting configurations in Figures A, B and C on the next page . H. Slim Line W all Thimble 1. Assembling Slim Line T rim Ring and Heat Shield 2. Installing Slim Line T rim Ring and Heat Shield Figure 5.31 Lay the trim ring on flat surface and b[...]

  • Seite 24

    Page 24 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F FIG. A 90 DEGREE ELBOW FIG. C MINIMUM CLEARANCE Figure 5.33 FIG. B 45 DEGREE ELBOW TERMINA TION CAP HEA T SHIELD OVER TOP HALF OF PIPE TRIM RING W ALL THIMBLE CENTER LINE MINIMUM OF 6 in. (152Mm) OF PIPE THROUGH THE WALL INTERIOR W ALL (2 in. (51mm) clearance from rear of stove) 90° EL[...]

  • Seite 25

    September 1, 2008 Page 25 Quadra-Fire · Garnet-T · 7016-127F 6 Gas Information A. Fuel Conversions Before making gas connections ensure that the appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a quali- fied technician us[...]

  • Seite 26

    Page 26 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F A B C Mounting Screws Pressure Regulator T ower Diaphragm Figure 6.5 T urn control knob to the OFF position, ensure that gas supply to the valve has been turned off. Using a T orx TH20, or slotted screwdriver , remove the three pressure reg- ulator mounting screws (A) , pressure regulat[...]

  • Seite 27

    September 1, 2008 Page 27 Quadra-Fire · Garnet-T · 7016-127F B. Gas Pressures If the pressure is not sufficient, ensure: 1) the piping used is large enough. 2) the supply regulator is adequately adjusted. 3) that the total gas load for the residence does not exceed the amount supplied. The supply regulator (the regulator that attaches directly t[...]

  • Seite 28

    Page 28 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F • A small amount of air will be in the gas supply lines. When first lighting appliance it will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally . Air only needs to be purged again if gas valve has been turned to the[...]

  • Seite 29

    September 1, 2008 Page 29 Quadra-Fire · Garnet-T · 7016-127F 7 Electrical Information A. Recommendation for Wire C. Standing Pilot Ignition System Wiring See B5 below for recommended maximum lead length (two wire) when using wall thermostat/switch. B. Connecting to the Appliance This appliance DOES NOT require 1 10 V AC supply for operation. A wi[...]

  • Seite 30

    Page 30 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Figure 7.1 CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. V erify proper operation after servicing. Shock hazard. • Replace damaged wire with type 105 O C rated wire. • Wire must have high temperature[...]

  • Seite 31

    September 1, 2008 Page 31 Quadra-Fire · Garnet-T · 7016-127F 8 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the firebox. B. Leg Leveling System Figure 8.1 Thread Allen bolts through nuts until flush. The Allen bolts and nuts are included in the component pack inside the appliance firebox. Fig[...]

  • Seite 32

    Page 32 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F D. Accessories Install approved accessories per instructions included with accessories. Refer to Section 12 for appropriate accesso- ries. Shock or fire risk. Use ONL Y optional accessories approved for this appliance. • Using non-listed accessories voids warranty . • Using non-lis[...]

  • Seite 33

    September 1, 2008 Page 33 Quadra-Fire · Garnet-T · 7016-127F H. Blower Installation 11 10 KIT CONTENTS: 1 - Blower Mounted in Housing 2 - Speed Control Knob 3 - Pal Nut 4 - Ceramic Snap Disc 5 - Speed Control (Rheostat) 6 - Wire Harness (attached to Blower) 7 - 12 Screws 8 - 12 inch Glass T ape 9 - 1 Zip T ie 10 - Bracket #1 11 - Snap Disc Bracke[...]

  • Seite 34

    Page 34 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Figure 8.12 Install the snap disc. A snap disc bracket is located in the appliance's component bag. Bend the two spade temi- nals on the snap disc from a horizontal to a vertical position. Insert the snap disc through the hole in the snap disc bracket and attach the two white wires[...]

  • Seite 35

    September 1, 2008 Page 35 Quadra-Fire · Garnet-T · 7016-127F Figure 8.15 Blower Wiring Diagram Fan Speed Control Thermal Disc (1 10 V AC) Power Cord BLACK Bushing Strain Relief GREEN BLACK Ground Fan Assembly BLACK BLACK WHITE WHITE WHITE[...]

  • Seite 36

    Page 36 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F I. Ignition Module Access and Battery Replacement Figure 8.16 The ignition module is located under the appliance attached to the decorative cover . Lift off the appliance top and place it on a flat surface, with the porcelain side up to prevent damage. Remove the appliance front by slid[...]

  • Seite 37

    September 1, 2008 Page 37 Quadra-Fire · Garnet-T · 7016-127F 9 Operating Instructions A. Before Lighting Appliance Read this entire manual prior to using the appliance. Failure to follow the instructions may result in property damage, bodily injury, or even death. Glass door must be in place when appliance is operating. Risk of: • Combustion Fu[...]

  • Seite 38

    Page 38 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F C. Lighting Appliance 1. Set the thermostat to lowest setting. 2. T urn off all electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "OFF" position. FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS [...]

  • Seite 39

    September 1, 2008 Page 39 Quadra-Fire · Garnet-T · 7016-127F D. After Appliance is Lit When you light your appliance, you may notice that it pro- duces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours [...]

  • Seite 40

    Page 40 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 10 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective act[...]

  • Seite 41

    September 1, 2008 Page 41 Quadra-Fire · Garnet-T · 7016-127F Symptom Possible Cause Corrective Action 3. (Continued) c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter at the thermopile terminals. The millivolt meter should read greater than 125mV . If the reading is [...]

  • Seite 42

    Page 42 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 11 Maintaining and Servicing Y our Appliance Although the frequency of your appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-up at the beginning of each heating season. Risk of injury o[...]

  • Seite 43

    September 1, 2008 Page 43 Quadra-Fire · Garnet-T · 7016-127F Inspect Maintenance T asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to air flow . 3. V erify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gasket seal [...]

  • Seite 44

    Page 44 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F 12 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only . For clearances refer to Section 3. Figure 12.1 Appliance Dimensions A B F C D E Location Inches Millimeter Location Inches Millimeter A 27-3/4 705 D 17-3/8 441 B 17[...]

  • Seite 45

    September 1, 2008 Page 45 Quadra-Fire · Garnet-T · 7016-127F B. V ent Components Diagram Figure 12.2 SL-D Series V ent Components 4 in. (102 mm) inner pipe 6-5/8 in. (168 mm) outer pipe 9-1/4 in. (235mm) 6-1/2 in. (165mm) 6-5/8 in. (168mm) 17-24 in. (432-610mm) 1 1-3/4 in. (298mm) 5-3/4 in. (146mm) 6-5/8 in. (168mm) 6-3/8 in. (162mm) 6-1/2 in. (1[...]

  • Seite 46

    Page 46 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F C. V ent Components List Description HHT SL-P M= Multi Pack (6) Simpson Dura-V ent DirectV ent Pro Selkirk Direct-T emp Amerivent Direct Security Secure V ent 4” Pipe Length, Galvanized SLP4M ---- 4” Pipe Length, Black SLP4-BK ---- 6” Pipe Length, Galvanized SLP6M 46-DV A-06 4DT -[...]

  • Seite 47

    September 1, 2008 Page 47 Quadra-Fire · Garnet-T · 7016-127F 45° Elbow , Swivel, Black - 46DV A-E45B - - SV4EB45 90° Elbow , Galvanized SLP90M See Swivel 4DT -EL905 4D90LS - 90° Elbow , Black SLP90-BK See Swivel 4DT -EL90SB 4D90LBS SV4EBR90 90° Elbow , Swivel, Galvanized - 46DV A-E90 - - SV4E90 90° Elbow , Swivel, Black - 46DV A-E90B - - SV4[...]

  • Seite 48

    Page 48 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F D. Service Parts List R GARNET -T (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 6-16-04 Ending Manufacturing Date: Item # Description Item # Description Item # Description 1 V alve Cover 9 Pilot Assembly 17 Baffle 2 Knob, Extension, SIT , ON/OFF 10 Air Shutter Assembly [...]

  • Seite 49

    September 1, 2008 Page 49 Quadra-Fire · Garnet-T · 7016-127F IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealer's VIP site. When ordering, supply serial and model numbers to ensure correct service parts. D. Service Parts List (cont’d.) R GARNET -T (NG, LP) Exploded Parts Diagram Beginning Manuf[...]

  • Seite 50

    Page 50 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Hinge Pins, Gold (set of 2) 844-5750 6 Ignition Module 230-1880 Injector , Pilot, EZ, LP , 35 200-2630 3 Knob, Extension, HI/LO, S.I.T . 571-533 2 Knob, Extension, ON/OFF , S.I.T . 571-534 Knob, Speed Control 19942 Latch, Draw 229-0640 Leveling Assembly 7000-000 5 Log Set 7016-018 Magne[...]

  • Seite 51

    September 1, 2008 Page 51 Quadra-Fire · Garnet-T · 7016-127F IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealer's VIP site. When ordering, supply serial and model numbers to ensure correct service parts. E. Accessories R GARNET -T (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 6-16[...]

  • Seite 52

    Page 52 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Date of Service Performed By Description of Service F . Service And Maintenance Log[...]

  • Seite 53

    September 1, 2008 Page 53 Quadra-Fire · Garnet-T · 7016-127F G. Homeowner ’ s Notes[...]

  • Seite 54

    Page 54 September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F H. W arranty Policy Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the Unite[...]

  • Seite 55

    September 1, 2008 Page 55 Quadra-Fire · Garnet-T · 7016-127F  HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or main- tenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identification label furnished with the[...]

  • Seite 56

    Page 56 Quadra-Fire · Garnet-T · 7016-127F September 1, 2008 Hearth & Home T echnologies 1445 North Highway Colville, W A 991 14 Division of HHT INDUSTRIES CONT ACT INFORMA TION : DEALERSHIP WHERE PURCHASED: ______________________________________ _______________________________________ _______________________________________ DEALER TELEPHONE:[...]