Intel SR9000MK4U Bedienungsanleitung

Intel ® Server System SR9000MK4U Product Guide Intel Order Number D71314-004[...]

ii Intel ® Server System SR9000 MK4U Product Guide Disclaimer Information in this document is provid ed in connection wi th Intel® p roducts. No licens e, express or implied, by estoppel or otherwise, to any intellectual property righ ts is granted by this document. Exce pt as provided in Intel's Terms and Conditions of Sale for such product[...]

iii Safety Information Important Safety Instructions Read all caution and safety statements in th is documen t before performing any of the instructions. See also Intel Server Boards an d Server Chassis Safety Information on the Resource CD and/or at http://support.intel.com/suppo rt/motherboards/server/sb/cs- 010770.htm . Wichtige Sicherheitshinwe[...]

iv Intel ® Server System SR9000MK4U Product Guide Warnings Heed safety instructions: Before working with your server product, whether you are using this guide or any oth er resource as a reference, pay close attention to the safety instructions. Y ou must adhere to the assembly instructions in this guide to ensure and maintain compliance with exis[...]

Intel ® Server System SR9000MK4U Product Guide v Installing or r emoving jumpers: A jumper is a small pla stic encased conductor that slips over two jumper pins. Some jumpers have a sm all tab on top that you can grip with your fingertips or with a pair of fine needle nosed p liers. If your jumpers d o not have su ch a tab, take care when using ne[...]

vi Intel ® Server System SR9000MK4U Prod uct Guide[...]

vii Preface About this Manual Thank you for purchasing and using Intel ® server products. This manual is written for system technici ans who are responsible for troubleshooting, upgrading, and ma nag ing the Intel ® Server System SR9000MK4U . Th is document provides an overview of the features of the serv er syst em utilities, an d instructions o[...]

viii Intel ® Server System SR9000MK4U Product Guide Product Accessories Y ou may need or want to purchase one or mo re of the following accessory items for your server: Processor , memory D IMMs, hard drive, USB floppy drive, CD-ROM or DV D-ROM drive, RAID controller , operating system. For information about which accessories, memo ry , processors[...]

Intel ® Server System SR9000MK4U Product Guide ix See also the Resource CD that came with your server system. DIMMs that have been tested with this prod uct Tested Memory List For drivers Driver (for an extensive list of available drivers) Operating System Driver (f or operating system drivers) For firmware and BIOS updates, or for BIOS recovery F[...]

x Intel ® Server System SR9000MK4U Product Guide Powering the System On and Off Powering On the System Power 1. Connect the power cables to AC input po wer connectors in the back of the system and to the outlet. If 100 - 1 10 V AC is used, both power supplies must be connected. 2. If peripheral devices are attached that ne ed to be turned on fi rs[...]

Intel ® Server System SR9000MK4U Product Guide xi Contents Safety Information ......... ................................. ................................................. .......... iii Important Safety Instructions ................................................................ ................................ i ii Wichtige Sicherheitshinweise [...]

xii Intel ® Server System SR9000MK4U Product Guide Installing the Front Bezel ........................................... .................................................. 35 Installing and Removing the Top Cover .................................................. ............................ 36 Removing the Top Cover .............................[...]

Intel ® Server System SR9000MK4U Product Guide xiii Removing the KVM Card ........................................ ..................................................... 89 Installing the KVM Card ..................................................... .......................................... 90 Installing and Removing the PCI Card Divider ........[...]

xiv Intel ® Server System SR9000MK4U Product Guide How to Use Selview to Read the System Event Log ........................................... ..... 160 How to Collect System and Error Logs ................................ ..................................... 160 Taking Corrective Actio n ..........................................................[...]

Intel ® Server System SR9000MK4U Product Guide xv Consignes de sécurité sur le serveur ..................... ................................................... 208 Sécurité: avertissements et mises en garde .............................................................. 208 Domaines d’utilisation prév us ................................. ..[...]

xvi Intel ® Server System SR9000MK4U Prod uct Guide[...]

Intel ® Server System SR9000MK4U Product Guide xvii List of Figures Figure 1. Intel ® Server System SR9000MK4U Three Dimensional View .................................. 1 Figure 2. Chassis Front View ......................................................................................... .......... . 4 Figure 3. Front Panel Controls and Indicat [...]

xviii Intel ® Server System SR9000MK4U Product Guide Figure 43. Removing Optica l Drive from Server ..................................................................... 53 Figure 44. Removing the Optical Drive from th e Bracket........................................................ 54 Figure 45. Locating the Fans ................................[...]

Intel ® Server System SR9000MK4U Product Guide xix Figure 90. Checking the Backplane Cover Latches ................................................................ 89 Figure 91. Locating the KVM Card ............................................................ .............................. 90 Figure 92. Removing the PCI Card Divide r ............[...]

xx Intel ® Server System SR9000MK4U Prod uct Guide Figure 137. SATA Connections on Hard Drive Backplane ............................................... .... 168 Figure 138. IDE Connection and Ca ble Routing .................................................... ............... 169 Figure 139. MVR Connectors ..........................................[...]

Intel ® Server System SR9000MK4U Product Guide xxi List of Tables Table 1. Additional Information and Software ............................................................... .......... viii Table 2. Server Physical Specifications .................................................................................... 1 Table 3. Chassis Feature Summar[...]

xxii Intel ® Server System SR9000MK4U Product Guide[...]

1 1 Intel ® Server System SR9000MK4U Chassis Overview The Intel ® Server System SR9000MK4U as shown in Figure 1 is a compact, high -density rack-mount server syst em with support for up to fo ur Intel ® Itanium ® 2 processors and 256-GB DDR2 SDRAM memory . The system is based on the Hitachi CF-3e board set and the Hitachi CF-3e chipset. The sys[...]

2 Intel ® Server System SR9000MK4U Product Guide Chassis Description Features are outlined in T able 3. Table 3. Chassis Feature Summary Feature Comment Server Configuration • Stand-alone system including external I/O PCI slots and disk expansion as needs grow • Support for Intel ® Itanium ® 2 processors • Support for 533 MHz Fron t Side B[...]

Intel ® Server System SR9000MK4U Product Guide 3 External Chassis Features System control buttons and indicators are located in several places on the chassis: • Chassis front — Front panel: Front panel switches and LEDs — Optical drive bay — Hot-swap hard drive bay: hard drive LEDs — Memory box: Memo ry box serviceability LEDs • Chassi[...]

4 Intel ® Server System SR9000MK4U Product Guide Chassis Front Figure 2 shows the front view of the chassis with the snap-on bezel in place. The bezel provides access to the optical drive, front pa nel controls, and the hot-swap hard drives. The bezel must be remove d to access the memory boxes. Figure 2. Chassis Front View A. Front Panel, see “[...]

Intel ® Server System SR9000MK4U Product Guide 5 Front Panel The front panel is located below the slimline op tical drive on the left-side of the chassis front. The front panel provides buttons and status indicator LEDs. Figure 3 shows the control buttons and status indicators on the fro nt panel. Figure 3. Front Panel Controls and Indic ators AF0[...]

6 Intel ® Server System SR9000MK4U Product Guide Optical Drive Bay The slim-line optical drive (DVD-ROM / CD-ROM drive) is ins erted from the front of the optical drive bay . The system power must be turned of f to remove or install this drive. Figure 4. Optical Drive Bracket wit h Drive Installed Note: Intel validates specific DVD-ROM / CD-ROM dr[...]

Intel ® Server System SR9000MK4U Product Guide 7 The hard drive carriers contain light-pipes that allow dual-color LED indicators to display through the bezel. The hard drive status is described in T able 4. Notes: • T o test the har d drive LEDs, do the following: — Install a har d drive. — Power on the system. — W atch for the LED status[...]

8 Intel ® Server System SR9000MK4U Product Guide Memory Box In memory mirror mode, memory box 0 is pair ed with memory box 1. Memory box 2 is paired with memory box 3. When mirro ring mode is used, either of the memory boxes with a pair can be hot-swapped. Figure 6 shows the front view of the memory box. Figure 6. Memory Box Front View Callout LED[...]

Intel ® Server System SR9000MK4U Product Guide 9 Chassis Rear Figure 7 shows the features found on the rear panel. Figure 7. Chassis Rear View AF001087 A B C D E F G H I A AC input power connectors B AC input power connectors C PCI Slots All slots support hot-plug PCI add-in cards. From left to right: – Slot 6: 133 MHz, 64-bit PCI-X*, full lengt[...]

10 Intel ® Server System SR9000MK4U Product Guide Table 5. NIC LEDs Item LED Color State Description Gigabit Ether, ports GbE1 and GbE0 ACT/LNK (right LED) Green On Link Green Blink Active None Off No link SPEED (left LED) Yellow On 1000 Green On 100 None Off 10 Fast Ether (Management LAN, KVM LAN), ports Ether0 and Ether1 ACT/LNK (right LED) Gree[...]

Intel ® Server System SR9000MK4U Product Guide 11 Internal Layout The following diagram shows the location of components inside of the server system. Figure 8. Open System, Top View AF001089 A B C D E F G H I J K L M N O P Q R S BB AA Z Y X W V U T A. System Fan 2 K. PCI-Express, x16, Slot 5 U. M emory Box 2 B. System Fan 0 L. PCI-X, Slot 6 V. DIM[...]

12 Intel ® Server System SR9000MK4U Product Guide Internal Chassis Features Power Supply Subsystem The 12 V hot-swap power supply modules are rated at 1390 W over an in put range of 200 - 240 V AC, and at 990 W over an input range o f 100-127 V AC. The power supply module has two outputs, that is, +12 V and +5 Vsb. The standby voltages +5 Vsb is a[...]

Intel ® Server System SR9000MK4U Product Guide 13 Each power supply contains three LEDs on the top surface. The LED locations and descriptions are as follows. Figure 9. Power Supply Indicators A Input Good LED I ndicates input pow er is good, when this LED (green) is on. B DC Output Good LED Indicates ou tput power is g ood, when this LED (green) [...]

14 Intel ® Server System SR9000MK4U Product Guide Cooling Subsystem The cabinet inlets have hot-s wap pable, 5+1 redundant fan s for cooling. 120 mm x 38 mm fans are used. They prov ide enough airflow to cool the system components, processors, memory and chipset, even if one of the six fans fails. The fans are located across the ce nter of the cab[...]

Intel ® Server System SR9000MK4U Product Guide 15 PCI Card Slot Figure 11. PCI Card Slot Indicator A Power LED Indicates PCI slot status is active. B Attention LED and lens switch Indicates error, when this yellow LED is on. The lens switch is used for hot installs / removals. AF001092 A B[...]

16 Intel ® Server System SR9000MK4U Product Guide[...]

17 2 Intel ® Server System SR9000MK4U Board Set Overview The board set for the Intel ® Server System SR9000MK4U consists of one main board, four memory box cards (installed in the memory bo xes), one hard drive backplane and one front panel board. The block diagram of Intel ® Server System SR9000MK4U is as follows. The connection points between [...]

18 Intel ® Server System SR9000MK4U Product Guide Main Board Figure 13. Main Board Layout AF001095 Processor Socket0 NDC0 NDC1 FAN0 VHDM0 PCI slot1 PCI slot2 PCI slot3 PCI slot4 PCI slot5 PCI slot6 PS0 COM VGA GbE LAN0/1 LAN0 (Management) USB2/3 USB0/1 ESB2 PXH Main Boa rd LAN1 (KVM) SAS VGA LAN VHDM1 VHDM2 VHDM3 ID SW FAN1 FAN2 FAN3 FAN4 FAN5 LAN[...]

Intel ® Server System SR9000MK4U Product Guide 19 Table 7. Main Board Components Board Location Component Desc ription P1/P2 Hitachi* NDC Node Controller: • One Front Side Bus – 533/667 MHz FSB support – Two processors per bus • Four interfaces connectin g to the memory controller • Three x8 PCI Express* ports • Proprietary high-speed [...]

20 Intel ® Server System SR9000MK4U Product Guide P9 LSI Logic* SAS1068 PCI-X* to 3 Gb/s 8-port SAS controll er. Four of the eight ports are used. • 1.5 and 3 Gb/s SAS a nd SATA data transfer rates per port, full duplex • 64-bit, 133 MHz PCI-X host interface • Integrated RAID support – Fusion-MPT* architecture – Integrated Striping* tech[...]

Intel ® Server System SR9000MK4U Product Guide 21 Table 8. Main Board External I/O Connectors Board Location Connector Description E1 Serial RS232C D-sub 9-pin serial port E2 VGA Mini D-sub 15-pin video port E3 USB 0/1/2/3 USB Type A port x4 E4 GbE LAN 0/1 RJ45 LAN port x2 E5 100 MbE LAN RJ45 LAN port x1 E6 100 MbE LAN RJ45 LAN port x1 (for KVM) T[...]

22 Intel ® Server System SR9000MK4U Product Guide Configuration Restrictions Note: When one or two 75-watt PCI-Expr ess* graph ics car ds ar e installed, the system will supply power for that slot during the powe r -on sequence or hot-add process. Then, on finding the vio lation of the configu ration r estri ction, the system halts the power suppl[...]

Intel ® Server System SR9000MK4U Product Guide 23 Processor Configurations Figure 14 shows the top view of main board, indicating the processor locations. T able 1 1 shows the allowed processor configurations . Choose your configuration from T able 1 1 and install each processor in the locations indicated by Figure 14. Figure 14. Processor Locatio[...]

24 Intel ® Server System SR9000MK4U Product Guide Memory Box Card Figure 15. Memory Box Card Layout Table 12. Memory Box Card Compone nts Board Location Component Description P1/P2 MC0/2 Memory Controller P3 Mirror LED See “Memory Box” on page 8 . P4 Attention LED See “Memory Box” on page 8 . P5 Power LED See “Memory Box” on page 8 . P[...]

Intel ® Server System SR9000MK4U Product Guide 25 DIMM Configurations Figure 16 shows the DIMM locations within e ach memory box. One memory box houses either four or eight DIMMs. For a four -D IMM configuration, th e DIMMs should be installed into locations JD0A1 , JD0B1, JD2B1 and JD2A1. Figure 16. DIMM Locations (Top View of Memory Box ) C8 JD2[...]

26 Intel ® Server System SR9000MK4U Product Guide Three memory modes are available. The me mory mode is selected depending on the number of memory boxes that are connected to one NDC chip, an d whether the BIOS i s configured for mirror mode. See th e following table for information. The following figures show the installation or der and upgrade p[...]

Intel ® Server System SR9000MK4U Product Guide 27 In the path to 1 -B no new memory box is needed and therefore ha s a lower cost for capacity addition. Memory mirroring is applicable to 3-A, but not to 2-A nor 1-B. AF001102 Upgr ade Pat h MC MC NDC NDC Single Mo de 1MMR/4DIMM Up gr a d e P at h Upgrad e Path MC MC MC MC MC MC MC MC NDC NDC Doubl [...]

28 Intel ® Server System SR9000MK4U Product Guide Figure 17. Memory Upgrade Path AF001103 Upgrad e Path MC MC NDC NDC Si ngle M ode 1MMR/8DIMM Up gr a d e P at h MC MC MC MC MC MC MC MC NDC NDC Doubl e Mode Mirror Mo de 4MMR/2 4DIMM W Z 1 - B 4-B MMR MMR MMR Upgr ade Path Upgrad e Path MC MC MC MC NDC NDC Si ngle M ode 2MMR/16DI MM X MMR MMR Up gr[...]

Intel ® Server System SR9000MK4U Product Guide 29 Hard Drive Backplane Figure 18. Hard Drive Ba ckplane Top View Figure 19. Hard Drive Backplane Bottom View Note: A vailable when additional SAS PCI ca r d is inserted into PCI slot. Table 15. Hard Drive Backplan e Connectors Board Location Connector Description C0 HDD0/1/2/3 SFF-8482 (SAS internal [...]

30 Intel ® Server System SR9000MK4U Product Guide Hard Drive Population The on-board SAS controller is connected to four of the eight hard drives, drives 0 through 3. Hard drives 4 through 7 requir e the addition of an add-in SAS card. Front Panel Board Figure 20. Front Panel Board Layout Table 16. Front Panel Board Components Board Location Compo[...]

Intel ® Server System SR9000MK4U Product Guide 31 Table 17. Front Panel Board Connectors Board Locatio n Connector Description C1 HM C2 DVD C3 USB4/5 USB Type A port x2[...]

32 Intel ® Server System SR9000MK4U Product Guide[...]

33 3 Installing and Removing Components T o complete many of the insta llation or removal procedures in this chapter, you will need to first install or remove other components. Fo r example, to remove the PCI card divider , you first need to remove the chassis cover , the power supplies, the power supply b ox, the CPU1/CPU2 MVR cable, the KVM card,[...]

34 Intel ® Server System SR9000MK4U Product Guide Installing and Removing the Front Bezel Y ou will need to remove th e front bezel to perform the following operations: • T o install or remove a memory box • T o install or remove DIMMs • T o install or remove an optical drive • T o install or remove the front control panel • T o install [...]

Intel ® Server System SR9000MK4U Product Guide 35 Installing the Front Bezel 1. Set the left or right side of the bez e l into place at the front of the system. 2. Set the opposite side of the bezel into place. 3. Push firmly until the bezel snaps into place. Figure 22. Installing the Front Bezel AF001105[...]

36 Intel ® Server System SR9000MK4U Product Guide Installing and Removing the Top Cover Y ou will need to remove the top cover to perform the following operations: • T o install or re move a power supply • T o install or remove the power supply box • T o install or remove the power supply su pport • T o install or remove a fan • T o inst[...]

Intel ® Server System SR9000MK4U Product Guide 37 Installing the Top Cover 1. Place the front edge of the cover on th e chassis . 2. Lower the rear of the cover into place, as shown by letter “A” in the figure below . Figure 24. Installing the Top Cover Installing and Removing a Hard Drive Y ou will need to remove the hard drive(s) or the hard[...]

38 Intel ® Server System SR9000MK4U Product Guide Installing a Hard Drive Caution: Befor e performing the pr ocedures written in this chapter , except for when hot-swapping, be sur e to turn off the system and disconnect all power plugs. 1. Push down on the button at the top of th e drive carrier lever . See letter “A” in the figure below . 2.[...]

Intel ® Server System SR9000MK4U Product Guide 39 Figure 26. Mounting a Hard Drive 7. Open the hard drive carri er lever if it is closed. 8. Slide the hard drive carrier into the bay along the guide rail. See the figure be low . 9. When the lower part of the lever touch es the bay , push the lever closed while pushing the carrier into the system. [...]

40 Intel ® Server System SR9000MK4U Product Guide Removing a Hard Drive Cautions: • Befor e performing the procedur es in this chapter , except for when hot-swapping, turn off the system and disconnect all power plugs. • If you attempt to replace a faulty har d driv e using inappropriate pr ocedures may r esult in data corruption. • Befor e [...]

Intel ® Server System SR9000MK4U Product Guide 41 4. Remove the four screws at the sides of the hard drive carrier . T wo screws are at each side of the carrier . See letter “A” in the figure below . Note: Do not r emove the metal EM I shield fr om the carrier . 5. Lift the drive from the carrier . Figure 29. Unmounting a Hard Drive 6. Determi[...]

42 Intel ® Server System SR9000MK4U Product Guide Hot-swapping a Hard Drive Note: Remove only the failed drive. Removing the wr ong drive could cause the syste m to malfunction or may cause data loss. 1. Use the LED indicators at the top of th e hard drive carriers to determine which drive has failed. The red LED indicates the failed hard drive. S[...]

Intel ® Server System SR9000MK4U Product Guide 43 Installing a Memory Box T o perform this procedure, you will first need to remove the front bezel. The steps below will direct you to the instructions on removi ng the front bezel at the appropriate location in the step sequence. Caution: Befor e performing the procedur es in this chapter , except [...]

44 Intel ® Server System SR9000MK4U Product Guide 6. Carefully slide the memory box into the bay . When the memory box is correctly inserted the notches at the sides of the meta l cover align with the edge of the bay . See the figure below . Figure 32. Installing the Memory Box 7. Close the metal cover . See letter “A” in th e following figure[...]

Intel ® Server System SR9000MK4U Product Guide 45 Removing a Memory Box T o perform this procedure, you will first need to remove the front bezel. The steps below will direct you to the instructions on removi ng the front bezel at the appropriate location in the step sequence. Caution: Befor e performing the procedur es in this chapter , except fo[...]

46 Intel ® Server System SR9000MK4U Product Guide Hot-swapping a Memory Box T o perform this procedure, you will first need to remove the front bezel. The steps below will direct you to the instructions on removi ng the front bezel at the appropriate location in the step sequence. Cautions: • Befor e hot-swapping the memory box, confirm that hot[...]

Intel ® Server System SR9000MK4U Product Guide 47 1. Remove the front bezel. For instructions , se e “Removing the Front Bezel” on page 34 . 2. Push the hot-swap button for the memory box you want to remove. T o cancel the operation, push the button ag ain within five seconds. 3. The power LED blinks; wait for all memory box LEDs to tu rn off.[...]

48 Intel ® Server System SR9000MK4U Product Guide Installing and Removing DIMMs DIMM Installation Guidelines Each installed memory box must have either four o r eight DIMMs installed, as sh own below . • Four DIMM installation: Install DIMM s in JD0B1, JD0A1, JD2B1, JD2A1 • Eight DIMM installation: DIMM s installed in each socket Note: When fa[...]

Intel ® Server System SR9000MK4U Product Guide 49 Installing DIMMs T o perform this procedure, you will first need to remove: • The front bezel • The memory box The steps below will direct you to the instructions for these procedures at the appropriate location in the step sequence. Cautions: • Befor e performing the pr oced ur es in this ch[...]

50 Intel ® Server System SR9000MK4U Product Guide Removing DIMMs T o perform this procedure, yo u will first need to remove: • The front bezel • The memory box The steps below will direct you to the instruc tions for these procedur es at the appropriate location in the step sequence. Cautions: • Befor e performing the procedur es in this cha[...]

Intel ® Server System SR9000MK4U Product Guide 51 Installing and Removing an Optical Drive Installing an Optical Drive T o perform this procedure, you will first need to remove the front bezel. The steps below will direct you to the instructions on removi ng the front bezel at the appropriate location in the step sequence. Note: Before performing [...]

52 Intel ® Server System SR9000MK4U Product Guide 4. W ith the rear of the optical drive facing you, as shown by letter “A” below , install the left side of the bracket onto the drive. The bracket (letter “B” in the figure) has a small tab that fits into a di mple in the drive sheetmetal. 5. Roll the right side of the bracket down until it[...]

Intel ® Server System SR9000MK4U Product Guide 53 Removing the Optical Drive T o perform this procedure, you will first need to remove the front bezel. The steps below will direct you to the instructions on removi ng the front bezel at the appropriate location in the step sequence. Note: Before performing the pr oced ur es in this section, turn of[...]

54 Intel ® Server System SR9000MK4U Product Guide 4. Push the lever to release the drive from th e bracket. See letter “A” in the figure below . Figure 44. Removing the Optical Drive from the Bracket 5. If you are not replacing the drive, insert the optical drive filler into the server until it clicks into place. Caution: Insert a blank/filler[...]

Intel ® Server System SR9000MK4U Product Guide 55 Installing and Removing a Fan Y ou will need to remove the fan(s) to perform the fo llowing operatio ns: • T o replace a fan • T o install or remove the fan box • T o install or remove the hard drive backplane • T o install or remove the mounting plate Installing a Fan T o perform this proc[...]

56 Intel ® Server System SR9000MK4U Product Guide 3. Note the fan orientati on in the figure below to make sure you insert the fan correctly . Insert th e fan into the bay . Figure 46. Installing a Fan 4. Determine your next course of action and refer to the appropriate steps: — If you are following these steps as part of another procedure, retu[...]

Intel ® Server System SR9000MK4U Product Guide 57 Removing a Fan T o perform this procedure, you will first need to remove the top co ver . The steps below will direct you to the instruc tions to remove the top cover at the appropriate location in the step sequence. Caution: Befor e performing the procedur es in this chapter , except for when hot-[...]

58 Intel ® Server System SR9000MK4U Product Guide 5. Determine your next course of action and refer to the appropriate steps: — If you have removed a fan to replace a failed fan, see “Installing a Fan” on page 55 . — If you are following these steps as part of another procedure, return to tha t procedure. Hot-swapping a Fan T o perform thi[...]

Intel ® Server System SR9000MK4U Product Guide 59 Installing and Removing a PCI Card Y ou will need to remove the PCI card(s ) to perform the fo llowing op eratio ns: • T o replace a PCI card • T o install or remove the PCI card divider • T o install or remove the fan box • T o install or remove the air flow guide • T o install or remove[...]

60 Intel ® Server System SR9000MK4U Product Guide 4. Push the PCI card lock firmly to unlock the card or the slot cover . See the figure below . Figure 51. Unlocking a PCI Card Lock 5. Remove the PCI slot cover . See the figure below . Keep the slot cover for future use. Figure 52. Removing a PCI Slot Co ver AF001139 AF001140[...]

Intel ® Server System SR9000MK4U Product Guide 61 6. Install the PCI card. See Figure 54. — For a short-length card, insert the PCI card firmly into the slot. — For a full-length card: Insert the PCI card in to the slot. The end of the card at the front side of the chassis must inserted an d locked into place in the PCI tail lock. See Figure 5[...]

62 Intel ® Server System SR9000MK4U Product Guide 7. Pull the PCI card lock firmly until i t clicks into place. See the figure below . Figure 55. Locking a PCI Ca rd into Place 8. Lower the PCI caution plate. Se e letter “A” in the figure below . Figure 56. Closing the PCI Caution Pl ate 9. Attach any cables necessary for the card you installe[...]

Intel ® Server System SR9000MK4U Product Guide 63 Removing a PCI Card T o perform this procedure, you will first need to remove the top co ver . The steps below will direct you to the instruc tions to remove the top cover at the appropriate location in the step sequence. Cautions: • Befor e performing the pr ocedures in this section, except for [...]

64 Intel ® Server System SR9000MK4U Product Guide 3. Push the PCI card lock firmly to un lock the PCI card. See the figure below . Figure 58. Unlocking a PCI Card Lock 4. Remove the PCI card and place it on a clean, static-free surface. — For a short-length card, pull the PCI card from the slot. — For a full-length card: Pull back on the PCI t[...]

Intel ® Server System SR9000MK4U Product Guide 65 5. Insert the slot cover over the opening at the rear of the chassis. Note: Be sur e to inse rt a slot cov er ov er an y unused slot. An uncover ed slot may affect the cooling system. Figure 60. Installing a PCI Slot Cover 6. Pull the PCI card lock until it locks into place. See the figure below . [...]

66 Intel ® Server System SR9000MK4U Product Guide 7. Close the PCI caution plate. See the figure below . Figure 62. Closing the PCI Caution Pl ate 8. Determine your next course of action and refer to the appropriate steps: — If you have removed a PCI card and need to replace it, see “Installing a PCI Card” on page 59 . — If you are followi[...]

Intel ® Server System SR9000MK4U Product Guide 67 Hot-Plugging a PCI Card T o perform this procedure, you will first need to remove the top co ver . The steps below will direct you to the instruc tions to remove the top cover at the appropriate location in the step sequence. Caution: Use caution when installing th e add-in car d to avoid touching [...]

68 Intel ® Server System SR9000MK4U Product Guide Installing and Removing a Power Supply Y our system was shipped to you with two po wer supplies installed. Both power supplies must be installed and plugged in when a 1 1 0 V out let is used. Hot-swapping is not available under this condition. One power supply can be used when it is connected to a [...]

Intel ® Server System SR9000MK4U Product Guide 69 Figure 64. Removing a Power Supply Filler 3. Simultaneously push the two levers on the top of the po wer supply slightly outward and then raise them to un lock the power supply . See letter “A” in the following figure. 4. Use the handle on the power supply to lowe r it into the system. See lett[...]

70 Intel ® Server System SR9000MK4U Product Guide 5. Push down the two levers on the top of the power supply to lock it into place. See letter “A” in the figure below . 6. Lower the handle on the power supp ly . See letter “B” in the figure. Figure 66. Locking the Power Supply into Place 7. Determine your next course of action and refer to[...]

Intel ® Server System SR9000MK4U Product Guide 71 1. Remove the top cover . For instructions, see “Removing the T op Cover” on page 3 6 . 2. Simultaneously push the two levers on the top of the po wer supply slightly outward and then raise them to unlo ck the power supply . See lette r “A” in the figure below . Figure 67. Opening the Power[...]

72 Intel ® Server System SR9000MK4U Product Guide 4. If you are not installing a replacement power supply , insert the power supply filler panel (see letter “A” in the figure below) and tighten the captive screw to attac h it to the open slot. See letter “B” in the figure. Caution: Install a filler panel into any unused slot. An open slot [...]

Intel ® Server System SR9000MK4U Product Guide 73 Hot-swapping a Power Supply T o perform this procedure, you will first need to remove the top co ver . The steps below will direct you to the instruc tions to remove the top cover at the appropriate location in the step sequence. Cautions: • Be sur e to remove only the failed component. R emoving[...]

74 Intel ® Server System SR9000MK4U Product Guide 3. Disconnect the power cable from the power supply you want to replace . 4. Remove the power supply . For instructions, see “R emoving a Power Supply” on page 70 . Return to these steps after removing the power supply . 5. Install the new power supp ly . For instructions, see “Installing a P[...]

Intel ® Server System SR9000MK4U Product Guide 75 4. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you have removed your front control panel / optic al drive assembly and need to replace it, see “Installing the Front Control Panel and Optical Drive Assembly” on page 75 . — If you are following these steps[...]

76 Intel ® Server System SR9000MK4U Product Guide Installing and Removing the Power Supply Box Before beginning these steps, po wer down your server system and u nplug all AC power cords. Y ou will need to remo ve the power supply box to pe rform the followi ng operations: • T o install or remove the power supply su pport • T o install or remo[...]

Intel ® Server System SR9000MK4U Product Guide 77 1. Disconnect the CPU1 / CPU2 MVR cable fro m the main board . T o disconne ct this cable, press and hold the latch on th e cable connector while pulling on the connector . See the figure below to locate the MVR cable connection. Figure 73. Locating the CPU1 / CPU2 MVR Conn ection 2. Disconnect the[...]

78 Intel ® Server System SR9000MK4U Product Guide 5. Loosen the two captive screws on the exteri or of the system. One screw is on each side of the system. See the figure below . Figure 75. Loosening the Exterior Captive Screws 6. Loosen the two captive screws inside the system. See the figure below . Figure 76. Loosening the Interior Captive Sc r[...]

Intel ® Server System SR9000MK4U Product Guide 79 7. Lift up the front end of the power supply box first, then lift the power supply box from the system. See the figure below . Figure 77. Lifting the Power Supply Box from System 8. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as p[...]

80 Intel ® Server System SR9000MK4U Product Guide Installing the Power Supply Box These steps assume you have just removed the power supply box, as des cribed in “Removing the Power Supply Box ” on page 76 and your system is partia lly disassembled. 1. Set the rear of the power supply box into the chassis, ensuring th at the two slots in the c[...]

Intel ® Server System SR9000MK4U Product Guide 81 3. T ighten the two captive screws at the bottom of the power supply box. See the figure below . Figure 80. Tightening the Internal Power Supply Box Screws 4. T ighten the two screws on the exterior of the system. One screw is on each side of the system, as shown below . Figure 81. Tightening the E[...]

82 Intel ® Server System SR9000MK4U Product Guide Figure 82. Locating the CPU1 / CPU2 MVR Connection 6. Connect the IDE cable from the main board. See letter “A” in the figure below . 7. Connect the SAS4I cable from the main boa rd. T o disconnect the cable, press both ends of the cable to be unlocked, and then disconnect it. See letter “B?[...]

Intel ® Server System SR9000MK4U Product Guide 83 9. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — If you are ready to re-assemble your ser ver system, install the following items, in order: ✧ All installed power supp[...]

84 Intel ® Server System SR9000MK4U Product Guide 1. Loosen the two screws that hold the power supply support in place. See the figure below . Figure 84. Loosening the Power Supply Support Captive Screws 2. Lift the power supply suppo rt to remove it from the system. See the figure below . Figure 85. Lifting the Power Su pply Support from System A[...]

Intel ® Server System SR9000MK4U Product Guide 85 3. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — Install a replaceme nt po wer supply support. For instructions, see “Installing the Power Supply Support” on pa ge 8[...]

86 Intel ® Server System SR9000MK4U Product Guide 2. T ighten the two captive screws at the botto m of the power supply support. See the figure below . Figure 87. Tightening the Powe r Supply Support Screws 3. Determine your next course of action and refer to the appropriate steps: — If you are following these steps as part of another procedure,[...]

Intel ® Server System SR9000MK4U Product Guide 87 Installing and Removing the Hard Drive Backplane Cover Before beginning these steps, power down yo ur server system and unplug all AC power cords. Y ou will need to remove the hard drive back plane cover to perform the follo wing operations: • T o install or remove the fan box • T o install or [...]

88 Intel ® Server System SR9000MK4U Product Guide Installing the Hard Drive Backplane Cover These steps assume the top cover is already removed from the system. 1. Set the hard drive backplane cover into th e chassis, inserting the three tabs on the backplane cover through the slots in the chassis, as shown in the figure below . Figure 89. Install[...]

Intel ® Server System SR9000MK4U Product Guide 89 Figure 90. Checking the Backplane Cover Latc hes 4. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — Install the top cover . For instructions, see “Installing the T o p C[...]

90 Intel ® Server System SR9000MK4U Product Guide Remove these compon ents, in order , before beginning the steps below . The steps below do not guide you through re installing the component s you are removing or disconnecting in this step sequence. These steps assume you are removing the KVM card to either replace it, or to access anot her compon[...]

Intel ® Server System SR9000MK4U Product Guide 91 2. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — If you are ready to re-assemble your ser ver system, install the following items, in order: ✧ The power supp ly box. F[...]

92 Intel ® Server System SR9000MK4U Product Guide Remove these compon ents, in order , before beginning the steps below . The steps below do not guide you through re installing the component s you are removing or disconnecting in this step sequence. Th ese steps assume you are removing the PCI card divider to either replace it, or to access an oth[...]

Intel ® Server System SR9000MK4U Product Guide 93 Installing the PCI Card Divider These steps assume you have just removed the PCI card divider , a s described in “Removing the PCI Card Divider” on page 91 and your system is partially disassembled. 1. Insert the two guides of the PCI divider in to two guide holes near the bottom of the system.[...]

94 Intel ® Server System SR9000MK4U Product Guide 3. Install the CPU1 / CPU2 MVR cable. See th e figure below to lo cate the connection point on the server board. Figure 94. Locating the CPU1 / CPU2 MVR Connection 4. Determine your next course of action and refer to the appropriate steps: — If you are following these steps as part of another pro[...]

Intel ® Server System SR9000MK4U Product Guide 95 Installing and Removing the Air Flow Guide Before beginning these steps, power down yo ur server system and unplug all AC power cords. Y ou will need to remove the airflow guid e to complete the following procedures: • T o install or remove the fan box • T o install or remove the hard drive bac[...]

96 Intel ® Server System SR9000MK4U Product Guide 1. Pull the air flow guide upward to remo ve it from the system. See the figure below . Figure 95. Removing the Air Flow Guide 2. Determine your next course of action and refer to the appropriate steps: — If you are following these steps as part of another procedure, return to tha t procedure. ?[...]

Intel ® Server System SR9000MK4U Product Guide 97 Installing the Air Flow Guide These steps assume you have removed th e air flow guide, as described in “Removing the Air Flow Guide” on page 95 and your system is partially disassembled. 1. Place the air flow guide i n the chassis . 2. V e rify all thre e hooks in the chassis alig n with the co[...]

98 Intel ® Server System SR9000MK4U Product Guide ✧ The KVM card, if necessary . For instructions, see “Installing the KVM Card” on page 90 . ✧ All installed PCI cards. For instructions, see “Installing a PCI Card” on page 59 . ✧ The hard drive backplane c over . For instructions, see “Installing the Hard Drive Backplane Cover” o[...]

Intel ® Server System SR9000MK4U Product Guide 99 • The air flow guide. For instructions, see “Removing the Air Flow Guide” on page 95 . • All installed fans. For instructions, see “Removing a Fan” on page 57 . Remove these components, in order , before beginning the st eps below . The steps below do not gu ide you through re inst alli[...]

100 Intel ® Server System SR9000MK4U Product Guide 2. Loosen the two captive screws on the interi or of the system, as shown by the figure below . Figure 98. Loosening the Interior Screws 3. Lift the fan box from the system, as shown below . Figure 99. Lifting the Fan Box from the Sy stem AF001222 AF001223[...]

Intel ® Server System SR9000MK4U Product Guide 101 4. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — Reinstall the fan box. For instructions, see “Installing the Fan Box” on page 101 . Installing the Fan Box These st[...]

102 Intel ® Server System SR9000MK4U Product Guide 2. T ighten the two screws at the bottom of th e fan box, as sh own by the figure below . Figure 101. Tightening the Internal Fan Box Screws 3. T ighten the two external screws, one at each side of the system, as shown by the figure below . Figure 102. Tighten the External Fan Box Screws AF001224 [...]

Intel ® Server System SR9000MK4U Product Guide 103 4. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — If you are ready to re-assemble your ser ver system, install the following items, in order: ✧ All installed fans. For[...]

104 Intel ® Server System SR9000MK4U Product Guide • All installed power suppli es. For instructions, see “Removing a Power Supply” on page 70 . • The power supply filler panel, if one is installed. For instructions, see “Installing a Power Supply” on page 68 . Follow step 2 only . • The power supply box. For instructions, see “Rem[...]

Intel ® Server System SR9000MK4U Product Guide 105 1. Disconnect all cables from the hard drive ba ckplane. 2. Remove the four screws from the hard dr ive backplane. See the following figure. Table 18. Loosening the Hard Driv e Backplane Screws AF001225[...]

106 Intel ® Server System SR9000MK4U Product Guide 3. Pull up slightly on the hard drive backplane to unhook the 12 hook s that hold the backplane into place. See letter “A” in the figure below . 4. Pull the backplane toward the center of th e system to disengage the 12 hooks. See letter “B” in the figure. 5. Lift the backplane from the sy[...]

Intel ® Server System SR9000MK4U Product Guide 107 Installing the Hard Drive Backplane These steps assume you have removed th e air flow guide, as described in “Removing the Hard Drive Backplane” on page 103 and your system is partially disassembled. 1. Set the hard drive backplane into place in the system. See lette r “A” in the figure be[...]

108 Intel ® Server System SR9000MK4U Product Guide 3. Install the four screws on the hard driv e backplane to secure the backplane to the system. See the figure below . Figure 105. Attaching the Hard Drive Backp lane to the System 4. Connect the cables to the backplane: — Connect the SAS cable to J54 P0 — If you have a second SAS cable, connec[...]

Intel ® Server System SR9000MK4U Product Guide 109 ✧ The hard drive backpl ane cover . For instructions, see “Installing the Hard Drive Backplane Cover” on page 88 . ✧ The power supp ly box. For instructions, see “Installing the Power Supply Box” on page 80 . ✧ All installed power supplies. For instructions, see “Installing a Power[...]

110 Intel ® Server System SR9000MK4U Product Guide Installing and Removing a Processor Before beginning these steps, po wer down your server system and u nplug all AC power cords. The following figure shows the components of th e processor assembly . Refer to this figure as needed during the installation process to identify the components discusse[...]

Intel ® Server System SR9000MK4U Product Guide 111 Removing a Processor T o perform this procedu r e, yo u first need to remove: • The top cover . For instruc tions, see “Removing the T op Cover” on page 36 . • All installed power suppli es. For instructions, see “Removing a Powe r Supply ” on page 70 . • The power supply filler pane[...]

112 Intel ® Server System SR9000MK4U Product Guide 1. Lift up on the MVR handles to remo ve them. One handle is on eac h side of the MVR. See the figure below . Figure 107. Removing the MVR Handles 2. Use a T orx-15 screwdriver to loosen th e two captive screw s on the LGA terminal that is located between the MVR and the heat sink. See letter “A[...]

Intel ® Server System SR9000MK4U Product Guide 113 5. If necessary , disassemble the pr ocessor . For instructions, see “Disassembling a Processor Assembly” on page 122 . 6. Determine your ne xt co urse of actio n and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure.[...]

114 Intel ® Server System SR9000MK4U Product Guide • The KVM card, if it is installed. For instructions, see “Removing the KVM Card” on page 89 . • All installed PCI cards. For instructions, see “Removing a PCI Card” on page 63 . • The PCI card divider . For instructions, see “Removing the PCI Card Divider” on page 91 . • The a[...]

Intel ® Server System SR9000MK4U Product Guide 115 4. Snap the pin shroud over the processor , verifying that the posi tioning pins of the pin shroud align with the notches in the processor . Figure 110. Installing the Pin Shroud over the Process or 5. Set the spring clip into place on the pr ocessor as shown below . The rounded edge of the spring[...]

116 Intel ® Server System SR9000MK4U Product Guide 6. While holding the spring clip in place on the processor , align the positioning pins on processor with the hol es in the h eat sink. 7. Set the processor in place over the heat sink. See the figure below . Figure 112. Setting the Processor ov er the Heat Sink 8. Use a T ork-15 screwdriver to ti[...]

Intel ® Server System SR9000MK4U Product Guide 117 9. Install the bolster plate onto the LGA terminal. See the figure below . Figure 114. Installing the Bolste r Plate onto the Processor 10. Make sure the processor lock on the main board i s in the unlocked position. See the figure below . Figure 115. Making Sure the Process or Socket is Unlocked [...]

118 Intel ® Server System SR9000MK4U Product Guide 1 1. Carefully set the processor assembly into place on the main board, aligning the heatsink screws with the co rresponding ho les in the server board. See the figure below . Caution: Do not allow the pr ocess or pins to ru b against the pr ocessor socket. If the pr ocessor does not seated easily[...]

Intel ® Server System SR9000MK4U Product Guide 119 14. Remove the protective cover from the LGA terminal on the back of the MVR. See the figure below . Figure 118. Removing the Protectiv e Cover from the LGA Terminal 15. Align the LGA terminal of the MVR with the LGA terminal pad of the processor assembly . Figure 119. Setting the MVR into Place o[...]

120 Intel ® Server System SR9000MK4U Product Guide 16. Use a T orx-15 screwdriver to tighten the four screws at the corners of the MVR. Use a torque level of 0.68[N .m] (6.9[kgf.cm]). See letter “B” in the figure bel ow . 17. Use a T orx-15 screwdriver to tighten the two screws on the LGA terminal. See letter “A” in the figure. Figure 120.[...]

Intel ® Server System SR9000MK4U Product Guide 121 19. Determine your next course of ac tion and refer to the appropriate steps: — If you are following these steps as part of another p r oc edure, return to that procedure. — If you removed the processor to replace it, see “Installing the Processor” on page 1 13 . — If you are ready to re[...]

122 Intel ® Server System SR9000MK4U Product Guide Disassembling a Processor Assembly Before beginning this procedure, follow a ll steps necessary to remove the processor from the server system. For instructions, see “Removing a Processor” on page 11 1 . 1. On the underside of the MVR, i nstall the protective cover over on the LGA terminal. Fi[...]

Intel ® Server System SR9000MK4U Product Guide 123 6. Lift the bolster plate from the LGA termin al on the underside of the heat sink / processor assembly . See the figure below . Caution: The pr ocessor c an be damaged if hand led improperly . Do not touch the pr oce ssor pins. Figure 124. Removing the Bolster Plate from the Processor 7. Use a T [...]

124 Intel ® Server System SR9000MK4U Product Guide 8. Lift the spring clip from the processor . See the following figure. Figure 126. Removing the Spri ng Clip 9. Lift the processor from the heat sink. 10. Carefully push out on one side of the pin shroud to release it from the processor . Cautions: • Do not touch the pr oc essor pins with either[...]

Intel ® Server System SR9000MK4U Product Guide 125 Installing and Removing the Mounting Plate Before beginning these steps, power down yo ur server system and unplug all AC power cords. Removing the Mounting Plate T o perform this procedu r e, yo u first need to remove: • The front bezel. For instructions, see “Removing the Front Bezel” on p[...]

126 Intel ® Server System SR9000MK4U Product Guide The steps do not guide you through reinsta lling the compon ents you are removing or disconnecting in this step seq uence. These steps assume you are removing the mounting plate to replace it. After completing these steps, continue with “Installing the Mounting Plate” on page 127 to replace yo[...]

Intel ® Server System SR9000MK4U Product Guide 127 Installing the Mounting Plate These instructions assume your server syst em is disa ssembled and you are replacing a mounting plate. 1. Hold the mou ntin g pla te by the front and b ack handles. 2. Set the back of the mounting plate into pl ace, verifying that the guid e pins in the chassis align [...]

128 Intel ® Server System SR9000MK4U Product Guide — The PCI card divider . For instructions, see “Installing the PCI Card Divider” on page 93 . — The KVM card, if necessary . For instructions, see “Installing the KVM Card” on page 90 . — All installed PCI cards. For instructi ons, see “Installing a PCI Card” on page 59 . — The[...]

Intel ® Server System SR9000MK4U Product Guide 129 Installing and Removing Chassis Handles Installing Chassis Handles T wo handles can be inst alled on each side of the server chas sis to aide in lifting and carrying the server system. Use the followi ng instructions to install each handle. 1. Set the handle into place in the sheetmetal indentatio[...]

130 Intel ® Server System SR9000MK4U Product Guide[...]

131 4 Configuration Software and Utilities The Extensible Firmware Interface (EFI) Boot Manager The EFI boot manager ena bles the user to control the bootin g environment of server . After power is on, the boot manager activates the sy stem with various wa ys according to the boot option settings. For example, the user can boot the EFI sh ell, an o[...]

132 Intel ® Server System SR9000MK4U Product Guide Table 19. Boot Maintenance Me nu Options Option Descript ion Boot from a File Automatically adds EFI applications or allows the user to boot from a specific file. When the user selects this option, the system searches for the EFI directory in all EFI System Part itions in the system. For each EFI [...]

Intel ® Server System SR9000MK4U Product Guide 133 Delete Boot Options Deletes a specific boo t option or all boot opti ons. To delete boot options: 1. Use the arrow keys to select [Delete Boot Option] 2. Press the <Enter> key. 3. Use the arrow keys to select the boot option to delete 4. Press the <Enter> key. 5. Press the <Y> ke[...]

134 Intel ® Server System SR9000MK4U Product Guide The Extensible Firmware Interface (EFI) Shell The EFI Shell is an EFI application that enabl es other EFI applications to start, EFI device drivers to load, and operating systems to bo ot. The combination of the EFI firmware and the EFI shell provides the system environment that can be changed eas[...]

Intel ® Server System SR9000MK4U Product Guide 135 EFI shell commands are listed below . Table 20. EFI Shell Commands Command Description alias [-d|-v|-b][AliasName][value] Displays, creates, or deletes alias on EFI shell. attrib [+/-ashr][-b][file...][ directory...] Displa ys or modifies attribute for file and directory. bcfg driver|boot [dump [-[...]

136 Intel ® Server System SR9000MK4U Product Guide help [-b]|[cmd] Displays command help informa tion. hexedit [[-f]FileName|[-d DiskName Offset Size]|[-m Offset Size]] Edits files in hex mode. if [not] condit ion then Executes co mmands under spec ific conditio n. load [-nc] file [file...] Loads the EFI driver. loadbmp [-c] [-t] [-i[UGA Instance][...]

Intel ® Server System SR9000MK4U Product Guide 137 LSI* SAS Utility See also “Integrated RAID User's Guide” at http://www .lsilogic.com. Formatting a Hard Drive Use the LSA SAS utility to format your hard drive. Use the fol lowing instructions. Note: Because ther e is a time lag between scr een ch anges, use caution in pr essing the [Ente[...]

138 Intel ® Server System SR9000MK4U Product Guide 4. The SAS T opology is di splayed. Select Direct Attach Devices and press the <Enter> key . 5. Select the hard drive and press the <D> key . LSI Logic MPT Setup Utility 2.00.06 .00 SAS Topology -- SAS1068 Device Identifier Device SAS1068(09:01:00) Info Controller Direct Attach Devices[...]

Intel ® Server System SR9000MK4U Product Guide 139 6. When the device properties are displaye d, select Format and press the <Enter> key . 7. When the following screen appears, press the <F> key to begin the format. Formatting a 36 GB hard dr ive takes about 15 minutes. LSI Logic MPT Setup Utility 2.00.06.00 Device Properties -- SAS106[...]

140 Intel ® Server System SR9000MK4U Product Guide 8. After the format has completed, press the <Esc> key several times, until you see the following screen. 9. Select Exit the Configuration Utility and Restart and press the <Enter> key to exit from the utility . Clearing the CMOS T o clear the CMOS, use the following steps : 1. T urn o[...]

Intel ® Server System SR9000MK4U Product Guide 141 Figure 131. Firmware Update Block Diagram AF001197 Integrated ROM file (The file that integrates the update ROM data.) LPC Bus Removable media Fwu pdate .ef i SAL code BMC code SDR data Removable device ESB2 FPGA BMC FWH SAL 8MB Flash ROM#1 SAL 8MB Flash ROM#0 BMC 512KB Hard ware Software EFI Shar[...]

142 Intel ® Server System SR9000MK4U Product Guide Fwupdate provides the following functions. • SAL/BMC update This function updates the SAL (FHW/SAL Spool) and the BMC (external flash) to SAL/BMC in the integrated ROM file specified by file name. When the “target machine type” and “model” existing in the integrated ROM file is unmatched[...]

Intel ® Server System SR9000MK4U Product Guide 143 Table 21. Command Line Descrip tion Option Functio n File name Integrated ROM file na me. The forma t is as follows: fw_aa-bb_cc-dd.rom aa-bb: SAL version cc-dd: BMC version The file name must be entered unless the /V or /H option is specified. /f or /F Does not confirm th e write oper atio n. Nor[...]

144 Intel ® Server System SR9000MK4U Product Guide Execution Screen Figure 133. FWUPDATE Execution Screen fs0:>fwupdate fw_01-02_01-03.rom[Enter] Firmware Update Utility Ver 1.0 Copyright (C) 1996-2000 Intel Corporation. All rights reserved. ************************************************************ Copyright (c) Hitachi, Ltd, 2000-2005. All [...]

Intel ® Server System SR9000MK4U Product Guide 145 Using System Setup This section describes the System Setup. This utility provides a way for the user to to modify the default server settin gs. Users can execute thi s u tility regardless of whether an operating system h as been installed. Setup stores most of the setting values in th e battery-ba[...]

146 Intel ® Server System SR9000MK4U Product Guide Navigating Setup Utility Screens The system setup utility consists of ten prim ary menus. Each menu occupies one screen and displays a list of menu items. Some menu items have sub-menus. The user can modify the settings of some menu items on the screen. T a ble 22 describes how to navigate the uti[...]

Intel ® Server System SR9000MK4U Product Guide 147 When the power button is pressed and release d while the main power is on, the power turns of f or the operating system begin s a shut down process. If the p ower button is held down, a forced power off is executed. If the po wer is forced of f, th en the server is not powered on after AC power re[...]

148 Intel ® Server System SR9000MK4U Product Guide When the system is configured with AfterPowerFailure = On, the power turns on automatically in the following situations: • When a power loss occurs while the equipment main power is on. • When the operating system is shut down normally , the main power turns off, and then a power loss occurs. [...]

Intel ® Server System SR9000MK4U Product Guide 149 Devices Screen T able 27 describes the menu items available on the Devices screen. Default values appear in brackets. Table 27. Devices Screen Primary Menu Item Sub Menu Item Options Description VGA Onboa rd VGA [Enable] Disable Enables / disables on-boa rd VGA.[...]

150 Intel ® Server System SR9000MK4U Product Guide Server Managem ent Screen T able 28 describes the menu items available on the Server Management scree n. Default values appear in brackets. Table 28. Server Mana gement Screen Primary Menu Item Sub Menu Item Options Description Console Redirection COM1 Console Redirection Press <Enter> Press[...]

Intel ® Server System SR9000MK4U Product Guide 151 System Information Screen System information as firmware version, and board, cha ssis, and product information are displayed. Configuring Serial-Over LAN 1. Open “System Setup Menu” on the screen. 2. Choose “Server Ma nagement”: System Information SAL Revision:xx-xx BMC Firmware Revision:x[...]

152 Intel ® Server System SR9000MK4U Product Guide 3. Choose “Console Redirection”: 4. Choose “COM1 Co ns ole Redirection”: 5. Set the COM1 Spee d to 9600/19200 : The baud rate must be equal to the speed specified for serial redi rec tion functions of the BIOS, and the speed used for the configuration of the boot loader an d operating syst[...]

153 5 Troubleshooting Initial Troubleshooting Steps The Intel ® Se rver System SR9000MK4U implements indicators to display the system status. These are useful as a first step in iden tifying a problem. Begin troubleshooting by using the table below to view symptoms and solutions. If you do not find the answer you need in the table, contin ue with [...]

154 Intel ® Server System SR9000MK4U Product Guide Cooling F ault LED System powe rs on, but then turns off quickly. Cooling Fault LED (orange) is on. Check that the cooling fan module is installed properly. Check that no fore ign matter is put in cooling fan module. Check that the intake/exhaust air is flowing. After the power-on, cooling fault L[...]

Intel ® Server System SR9000MK4U Product Guide 155 Processor System does not recognize part of the processors that were installed. Check that the processor/MVR are installed properly. Check that the MVR power cable is properly connected. Check that the processor is configured . Memory Box Memory capacity is ind icated less than actual loaded capac[...]

156 Intel ® Server System SR9000MK4U Product Guide Collecting System State Information If the information in the tabl e above did not resolve your p r ob lem, continue with the troubleshooting steps below . 1. Collect information: Collect informatio n about the state at which the problem occurs. POST (Power On Self T est) code and SEL (System Even[...]

Intel ® Server System SR9000MK4U Product Guide 157 Power Off State 1. Power up the system. 2. W ait for the EFI shell to begin. 3. Use the selview utility to obtain the system event log information. For instructions, see “How to Use Selview to Read the System Event Log” on page 160 . 4. Attempt to boot th e operating system. 5. Obtain operatin[...]

158 Intel ® Server System SR9000MK4U Product Guide EFI Shell Working State 1. Read the POST code. For instructions, see “How to Read the POST Codes” on page 159 . 2. Use the selview utility to ob tain the system event log in formation. For instructions, see “How to Use Selview to Read th e System Event Log” on page 160 . 3. Attempt to boot[...]

Intel ® Server System SR9000MK4U Product Guide 159 System Hang Status 1. Read the POST code. For instructions, se e “How to Re ad the POST Codes” on page 159 . 2. Boot the system to the EFI shell. 3. Use the selview utility to obtain the system event log information. For instructions, see “How to Use Selview to Read the System Event Log” o[...]

160 Intel ® Server System SR9000MK4U Product Guide How to Use Selview to Re ad the System Event Log 1. Use the EFI utility “selview” to acquire system event log (SEL) information. See the EFI Utility User ’ s Guide for help with this utility . 2. Record the output of selview utility . How to Collect System and Error Logs Collecting System an[...]

Intel ® Server System SR9000MK4U Product Guide 161 — Select an appropriate drive letter in the “Save in” list. — Enter “security .evt” as the file name. 13. Click Save. 14. Select “Save Log File As” from th e Operation menu on the menu bar . 15. The dialog box, “Save Security Log As”, opens. — Select an appropriate drive lett[...]

162 Intel ® Server System SR9000MK4U Product Guide security.csv ap.evt ap.csv system32.txt drivers.txt 30. Use Notepad to confirm the fo llowing files contain some texts: system32.txt drivers.txt 31. S top the external storage and re move the device from the system. Taking Corrective Action See “POST Codes” on pa ge 171 for suggested correc ti[...]

163 Appendix A: Console Setup On-board VGA The Intel ® Server System SR9000MK4U server can outpu t the SAL and EFI d isplays to on-board VGA. This subsection describes ho w to enable/disable the on-board VGA. 1. Select System Setup from the Boot Maintenance Menu of the EFI Boot M anager . See “The Extensible Firmware Interface (EFI) Boot Manager[...]

164 Intel ® Server System SR9000MK4U Product Guide 4. Select Onboard VGA from the VGA Menu. Set the option to either Enable or Disable . When you want to use on-board VGA, set it to Enable . 5. Select Exit twice and return to the System Setup Menu. 6. Select Save changes and Exit to end the System Setup. VGA Menu Examine and set VGA parameters. On[...]

Intel ® Server System SR9000MK4U Product Guide 165 Serial Console The Intel ® Server System SR9000MK4U server suppor ts headless functio n that redirects the VGA output and key board inp ut of SAL and EFI to t he COM1 po rt input /output . This subsection describes how to enab le/disable the headless functi on and how to set baud rate. 1. Select [...]

166 Intel ® Server System SR9000MK4U Product Guide 4. Select COM1 Console Redirection on the Console Redirection Menu screen. 5. Select Headless Support on the COM1 Console Redirection Menu and set it to Enable or Disable . When you want to use headless function, set it to Enable . 6. Select COM1 Speed and set i t to 9600 bps or 1920 0 bps. Set th[...]

167 Appendix B: Cabling This appendix provides a a brief guideline ab out how to correctly attach and detach cables to prevent damage to the cable, or to the conn ector on the cable end or the server board. This appendix also provides photographs of the cable connections in the server sys tem. Working with Ribbon Cables Make sure to detach (or atta[...]

168 Intel ® Server System SR9000MK4U Product Guide Cable Connections Figure 136. Connections Near Power Supply Box and PCI Card Divider Note: The figur e above shows the system with the power supply box r emoved. Figure 137. SATA Connections on Ha rd Drive Backplane A. SATA cable clip D. SATA 0 - 3 on-board connector B. IDE cable clip E. IDE conne[...]

Intel ® Server System SR9000MK4U Product Guide 169 Figure 138. IDE Connection and Cable Routing Note: The figur e above shows the system with the fans r emoved. Figure 139. MVR Connectors Note: The figur e above shows the system with the PC I car d divider and the power supply box re m o v e d . A. IDE connector on hard drive backplane B. IDE cabl[...]

170 Intel ® Server System SR9000MK4U Product Guide A. Control panel power connection on hard drive backplane C. Control panel data connector on server board B. Control panel data connector on hard drive backpl ane D. Control pa nel power cable on server board AF001438 A D C B[...]

171 Appendix C: POST Codes Table 31. POST Codes Generated by the BMC and Logge d at the Seven Segment LED Code Descriptions Classification Operation to Recover 0 0 reserved 0 1 SRAM Check Started Progr ess 0 2 SRAM Check Completed Progress 0 3 Active side BMC F/W binary file checking Progress 0 4 Spool side BMC F/W binary file checking Progress 0 5[...]

172 Intel ® Server System SR9000MK4U Product Guide 1 A Active side f ile update error Error 1 B Checksum error detected in active side Error 1 C SRAM check error (SRAM testing) Error 1 D SRAM check error (Hardware detects error in SRAM testing) Error 1 E Checksum error detected in both banks Error 1 F SRAM Par ity error detected Error 2 0 F/W in N[...]

Intel ® Server System SR9000MK4U Product Guide 173 3A r e s e r v e d 3B r e s e r v e d 3 C Detailed log collection started by WDT overflow Error BMC Error 3 D BMC restarted by WDT overflow Error 3 E Failed in task generat ion Error 3 F Illegal or mismatch format of GUID Error 4 0 CPU0 Thermal Trip Error, error event logged to SEL 4 1 CPU0 Config[...]

174 Intel ® Server System SR9000MK4U Product Guide 5 3 CPU3 Configuration Error (Disabled) Error, error event logged to SEL 5 4 CPU3 Configuration Error (Illegal Type) Error, error event logged to SEL 5 5 CPU3 Configuration Error (Different Type) Error, error event logged to SEL 5 6 CPU3 I2C Access Error (PIROM) Error, error event logged to SEL 5 [...]

Intel ® Server System SR9000MK4U Product Guide 175 6 A PS0 Power Failure (Insuffi cient Resources) Error, error event logged to SEL 6 B PS1 Power Failure (Insuffi cient Resources) Error, error event logged to SEL 6 C CPU / MMR Overinstall (PS Insufficient Resources) Error, error event logged to SEL 6 D MB I2C Access Error (Sensor0) Error, error ev[...]

176 Intel ® Server System SR9000MK4U Product Guide 9 0 Multiple Machine Check Interrupt Error, error event logged to SEL 9 1 MB Config Access Error (NDC30) Error, error event logged to SEL SEL List 9 2 MB Config Access Error (NDC31) Error, error event logged to SEL 9 3 MB Config Access Error (ESB2) Error, error event logged to SEL 9 4 MB Config Ac[...]

Intel ® Server System SR9000MK4U Product Guide 177 A B reserved AC r e s e r v e d AD r e s e r v e d A E reserved AF r e s e r v e d B7 r e s e r v e d B8 r e s e r v e d B9 r e s e r v e d B A reserved B B reserved BC r e s e r v e d BD r e s e r v e d B E reserved BF r e s e r v e d CX r e s e r v e d DX r e s e r v e d E X reserved FX r e s e [...]

178 Intel ® Server System SR9000MK4U Product Guide 4 1EA Console initialization 5 1F5 Chipset initialization Memory initialization 6 1F4 Recovery SDA initialization 7 1EC SAL_A shadowi ng Both BSP and AP jump to the shadowing code. 8 1E2 Decides whether recovery is necessary 9 1E4 Decides whether recovery is necessary 10 1E6 FIT checksums 11 1E7 R[...]

Intel ® Server System SR9000MK4U Product Guide 179 32 0F5 Clear error flags in chipset 33 0D0 EFI code shadowing EFI execution 34 AF~15 EFI POST task execution Table 32. POST Codes Generated by SAL and Logged at the Seven Segment LED No Code Description Operation to Recover Table 33. Error POST Codes Generated by SAL No Code Description Classifica[...]

180 Intel ® Server System SR9000MK4U Product Guide 25 0x8017 Unexpected failu re Error 26 0x8018 Unexpected failu re Error 27 0x8019 Unexpected failu re Error 28 0x8020 Unexpected failu re Error 29 0xC086 Unexpected failure detecte d while initializing memory. Error 30 0xC090~C092 OS machine check handler is not registered or not valid Error Pleas[...]

181 Appendix D: Installation/Assembly Safety Instructions English The power supply in this pr oduct contains no user-serviceable parts. Refer servicing onl y to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact typ e required. A product with more than one power supply will have a separate AC powe[...]

182 Intel ® Server System SR9000MK4U Product Guide After you have completed the six SAFETY steps above, you can remove the system covers. To do this: 1. Unlock and remove th e padlock from the ba ck of the system if a padlock has been installed. 2. Remove and save all screws from the covers. 3. Remove the cover(s). For proper cooling and airflow, [...]

Intel ® Server System SR9000MK4U Product Guide 183 Deutsch Benutzer können am Netzgerät dies es Produkts ke ine Reparaturen vornehmen. Das Produkt enthä lt möglicherweise mehrere Netzgeräte. Wartungsarbeiten müss en von qua lifizierten Technikern ausgeführt werden. Versuchen Sie nicht, das mitgeliefe rte Netzkabel zu ändern ode r zu verwen[...]

184 Intel ® Server System SR9000MK4U Product Guide SICHERHEISMASSNAHMEN: Immer wenn Sie die Gehäuseabdeckung abnehmen um an das Systemi nnere zu gelangen, sollten Sie folgende Schr itte beachten: 1. Schalten Sie alle an Ihr System angeschlossene n Peripheriegeräte aus. 2. Schalten Sie das System mit dem Hauptschalter aus. 3. Ziehen Sie den Strom[...]

Intel ® Server System SR9000MK4U Product Guide 185 Français Das System wurde für den Betrieb in einer normalen Büroumgebung entwickelt. Der Standort sollte: • "sauber und staubfrei sein (Haussta ub ausgenommen); • "gut gelüftet und keinen He izq uellen ausgesetzt sein (einschließlich direkter Sonnene instrahlung); • "kein[...]

186 Intel ® Server System SR9000MK4U Product Guide CONSIGNES DE SÉCURITÉ -Lorsque vo us ouvrez l e boîtier pour accéder à l'intérieur du système, suivez les consignes s uivantes: 1. Mettez hors tension tous les périphériques connectés au système. 2. Mettez le système hors tensio n en mettant l'interrupteur général en positi[...]

Intel ® Server System SR9000MK4U Product Guide 187 Español Le système a été conçu pour fonc tionner dans un cadre de travail normal. L'em placement choisi doi t être: • "Propre et dépourvu de poussi ère en suspension (sauf la poussière normal e). • "Bien aéré et loin des sources de cha leur, y compris du soleil direct[...]

188 Intel ® Server System SR9000MK4U Product Guide INSTRUCCIONES DE SEGURIDAD: Cu ando extraiga la tapa del chasis para acceder al interior del sistema, siga las siguientes instrucciones: 1. Apague todos los dispositivos peri féricos conectados al sistema. 2. Apague el sistema presionando el interruptor encendido / apagado. 3. Desconecte todos lo[...]

Intel ® Server System SR9000MK4U Product Guide 189 Italiano Existe peligro de explosión si la pila no se camb ia de forma adecuada. Utilice solamente pila s iguales o del mismo tipo que las recomendadas por el fabrican te de l equi po. Para deshacerse de las pilas usadas, siga igualmente las instruccio nes del fabricante. El sistema está diseña[...]

190 Intel ® Server System SR9000MK4U Product Guide L'interruttore attivato/disattivato nel pa nnello anteriore non interrompe l'alimentazione in c.a. del sistema. Per inte rromperla, è necessario scollegare tutti i cavi di alimen tazione in c.a. d alle prese a muro o dall'alimentazione di corrente. PASSI DI SICUREZZA: Qualora si ri[...]

Intel ® Server System SR9000MK4U Product Guide 191 Esiste il pericolo di un esplosione se la pila non vi ene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equ ivalente a quelle consigliate dal produttore. Per disfarsi delle pile usat e, seguire le istruzi oni del produttore. Il sistema è progettato per funzionare in un ambien[...]

192 Intel ® Server System SR9000MK4U Product Guide[...]

193 Appendix E: Safety Information Warning Labels The Intel ® Server System SR9000MK4U contains sev eral warning labels on the interior and exterior of the server system. These warnin g labels indicate comp onents that present a potential danger . Do not remove these warnin g labels. The following diagrams show the labels and their locations. A la[...]

194 Intel ® Server System SR9000MK4U Product Guide A warning on the side of the chassis warns you th at the chassis is heavy . Do not attempt to lift the server system alone. If handles are in stalled, at least two people should lift the system by grasping the handles. If the handles are not installed, at least two people should lift the handle by[...]

Intel ® Server System SR9000MK4U Product Guide 195 One of the following labels will be attached to your power supply . English Server Safety Information This document applies to Intel ® server boards, Intel ® server chassis (pedes tal and rack- mount) and installed peripherals. T o reduce the risk of bodily injury , el ectrical shock, fire , and[...]

196 Intel ® Server System SR9000MK4U Product Guide Safety Warnings and Cautions T o avoid personal injury or property damage , before you begin install ing the product, read, observe, and adhere to all of the follo wing safety instructions and information. The following safety symbo ls may be used throug hout the documentatio n and may be marked o[...]

Intel ® Server System SR9000MK4U Product Guide 197 Site Selection The system is designed to operate in a typica l office environment. Choose a site that is: • Clean, dry , and free of airb orne partic les (other than normal room dust). • W ell-ventilated and away fro m sources of heat including direct sunlight and radiators. • A way from sou[...]

198 Intel ® Server System SR9000MK4U Product Guide Power and Electrical Warnings Cautions: • The power button, indicated by th e stand-b y power marking, DOES NOT completely turn off the system AC power , 5V standby power is active whenever the system is plugged in. T o re move power fr om system, you must unplug the AC power cor d fr om the wal[...]

Intel ® Server System SR9000MK4U Product Guide 199 System Access Warnings Caution: T o avoid personal in jury or pr operty dama ge, the following safety instructions apply whenever accessing the inside of the pr oduct: • T urn off all peripheral dev i ces c onnected to this pr oduct. • T urn off the system by pressi ng the power button to off.[...]

200 Intel ® Server System SR9000MK4U Product Guide Rack Mount Warnings The equipment rack must be anchored to an unmovable support to p reven t it from tipping when a server or piece of equipment is exte nded from it. The equipment rack must be installed according to the rack manufacturer's instructions. Install equipment in the rack from the[...]

Intel ® Server System SR9000MK4U Product Guide 201 Other Hazards Battery Replacement Caution: Ther e is the danger of explosion if the battery is incorr ectly r eplaced. When r eplacing the battery , use only the b attery r e commended by th e equipment manufac tu r er . Dispose of batteries acco r ding to local or dinances and r egulations. Do no[...]

202 Intel ® Server System SR9000MK4U Product Guide Deutsch Sicherheitshinweise für den Server Das vorliegende Doku ment bezieht sich auf Inte l ® Serverplatinen, Intel ® Server gehäuse (Standfuß und Rack) sowie installierte Peri pheriegeräte. Es en thält W arnungen und V orsichtsmaßna hmen zur V ermeidung von Ge fahren durch V erletzung, S[...]

Intel ® Server System SR9000MK4U Product Guide 203 Zielbenutzer der Anwendung Dieses Produkt wurde in seiner Eigenschaft als IT -Gerät getestet, da s in Büros, Schulen, Computerräumen und äh nlichen öffentlichen Räumlichkeite n installiert werden kann. Die Eignung dieses Produkts für andere Einsatzb ereiche als IT (z. B. Medizin, Industrie,[...]

204 Intel ® Server System SR9000MK4U Product Guide Handhabung von Geräten Beachten Sie zur V ermeidung vo n V erletzungen oder Beschädigungen an den Geräten die folgenden Hinweise: • Halten Sie beim T ransportieren und Anhe ben von Geräten die örtlichen Gesundheits und Sicher heitsvorschriften ein. • V erwenden Sie mechanische oder andere[...]

Intel ® Server System SR9000MK4U Product Guide 205 Hinweis für Netzkabel W enn kein Netzkabel mit dem Produkt geliefert wurd e, kaufen Sie ein Kabel, das für die V orsicht: Pr üfen Sie zur V erme idung von S tromschlag- oder Feuer gefahr die mit dem Pr odukt zu verwendenden Netzkabel wie folgt: • Nehmen Sie keine Änderungen an einem Ne tzkab[...]

206 Intel ® Server System SR9000MK4U Product Guide Einbauen von Hot-Plug-Kompon enten sor gfältig vor , um nicht mit heißen Komponenten in Berührung zu kommen. Vo r s i c h t : Ber ühr en Sie nicht die r otierenden Lüfterflüge l, um V erletzungen zu vermeiden. Falls Ihr System mit eine Lüfterabdeckung besitzt, dar f es nicht ohne diese Abde[...]

Intel ® Server System SR9000MK4U Product Guide 207 Andere Gefahren Batterieaustausch V orsicht: W ird die Batterie unsachgemä ß ausgetauscht, besteht Explosionsgefahr . V erwenden Sie als Ersatz nur die vom Geräte hersteller empfohlene Batterie. Beachten Sie bei der En tsor gung von Batterien die gültigen B estimmungen. V ersuchen Sie nicht, e[...]

208 Intel ® Server System SR9000MK4U Product Guide Français Consignes de sécurité sur le serveur Ce document s’applique aux carte s serveur Inte l®, au châssis de serveur Intel® (sur pieds et sur rack) et aux périphériques install és. Pour réduire les risques de dommages corporels, d’électrocution, d’incendie et de dommages matér[...]

Intel ® Server System SR9000MK4U Product Guide 209 Domaines d’utilisation prévus Ce produit a été testé comme équipement informa tique (ITE) et peut être installé dans des bureaux, des écoles, des salle s informatiques et des endro its commerciaux similaires. L ’utilisation du présent produit dans des catégories et environnements de [...]

210 Intel ® Server System SR9000MK4U Product Guide Alimentation et av ertissements en m atière d’électricité Attention: Le bouton d’alimentation, indiqué par le symbole de mise en veille, NE COUPE P AS complètement l’alimentation secteur du système car le courant de veille 5 V r este actif lorsque le système est sous tension. Pour cou[...]

Intel ® Server System SR9000MK4U Product Guide 211 Avertissements sur l’accès au système Attention: Pour éviter de vous blesser ou d’endommager votr e équipement, les consignes de sécurité suivantes s’appliquent chaque fo is qu e vous accédez à l’intérieur du pr oduit: • Mettez hors tension tous les périphériques connectés à[...]

212 Intel ® Server System SR9000MK4U Product Guide Avertissements sur le montage en rack Le rack doit être fixé à un support inamov ible pour éviter qu’il ne bascule lors de l’extension d’un serveur o u d’un élément de l’équi pement. Le rack doit être installé conformément aux in structio ns du fabricant. Installez les équipem[...]

Intel ® Server System SR9000MK4U Product Guide 213 Refroidissement et ventilation Attention: Routez les câbles avec précaution comme indiqué pour minimiser les blocages de cir culation d’air et les pr oblèmes de r efr oidissement. Afin de permettre une ventilati on et un refr oi dissement corrects, ne mettez le système en marche que lorsque[...]

214 Intel ® Server System SR9000MK4U Product Guide Español Información de seguridad del servidor Este documento se aplica a las tarjetas de servidor de Intel ® , las carcasas de servidor de Intel ® (montaje en bastidor y en pedestal) y lo s dispositivos periférico s. Para reducir el riesgo de daños corporales, descargas eléctricas, fuego y [...]

Intel ® Server System SR9000MK4U Product Guide 215 Aplicaciones y usos previstos Este producto ha sido evaluado como equipo de tecnología in formática (ITE) que puede instalarse en oficinas, escuelas, salas de eq uip os informáticos o lugares de ámb ito comercial similares. Es posible que sea ne cesario llevar a cabo una evaluación adicional [...]

216 Intel ® Server System SR9000MK4U Product Guide Advertencias de alim entación y eléctricas Precaución: El botón de encendido, indicado con la ma r ca del modo de r eposo o stand-by , NO DESCONECT A completamente la alimentación de CA del sistema, ya que el modo de r eposo de 5 V sigue activ o mientras el si stema está enchufado. Para desc[...]

Intel ® Server System SR9000MK4U Product Guide 217 • Los cables de la fuente de alimentación deben estar conectados a los enchufes con una toma de tierra ad ecuada. Advertencias el acceso al sistema Precauci ón: Para evitar lesiones p ersonales o daños en la pr opiedad, se aplican las si gu ientes instrucciones de segurida d siempr e que se a[...]

218 Intel ® Server System SR9000MK4U Product Guide Advertencias sobre el montaje en bastidor El bastidor del equipo se debe su jetar con un soporte fijo para evitar que se caiga cuando se extraiga un servid or o una pieza del mism o. El bastidor del equipo debe instalarse siguiendo las instrucciones de l fabricante del bastidor . Instale el equipo[...]

Intel ® Server System SR9000MK4U Product Guide 219 Enfriamiento y circulación de aire Precauci ón: El tendido de los cables debe r ealizarse cuid adosamente tal y como se le indica para r educir al mínimo los pr oblemas de obstrucc ión de la ventilación y de r efrigeración. Para conseguir una r efrigeraci ón y corriente de air e adecu adas,[...]

220 Intel ® Server System SR9000MK4U Product Guide 简体中文 服务器安全信息 本文档适用于 Intel® 服 务器主板、Intel® 服务器机箱（基座和机架 固定件）和已安装的外设。为减少 人身伤害、电击 、 火 以及设备毁坏的危险，请 在安装或维护 Intel® 服务器产品之前阅读本文 档?[...]

Intel ® Server System SR9000MK4U Product Guide 221 预期应用使用 根据评估，本产 品为信息技术设备 (ITE)，可安装在 办公室、学校、 计算机房和类 似的商业场所。本产品对于 非 ITE 应用的其他产品 种类和环境（如医 疗、工业、住 宅、报警系统和测 试设备） 的适用 性尚有?[...]

222 Intel ® Server System SR9000MK4U Product Guide 为避免电击，请 在打开服务器之前 ，关闭服务器 并断开服务器上连 接的电源 线、电 信系统、网络和 调制解调器。 电源线警告 如果产品未提供 交流电线，请购买 一根您所在国 家批准使用的交流 电线。 注意事项 为避免电?[...]

Intel ® Server System SR9000MK4U Product Guide 223 注意事项 为避免受伤，请 勿触摸运转的风机 叶片。如果系 统的风机上配有防 护装置， 请勿卸 下风机防护装置 运行系统。 机架固定件警告 设备的机架须固 定在稳固的支座上 ，以防从中安 装服务器或设备时 倒塌。须 按照?[...]

224 Intel ® Server System SR9000MK4U Product Guide 其他危险 替换电池 注意 事项 不正确替换电池 可能导致爆炸危险 。替换电池时 ，请只使用设备生 产商推荐 使用的 电池。 请按当地法规处 置电池。 请勿对电池充电 。 请勿拆卸、刺穿 或以其他方式损坏 电池。 冷却和气流 [...]

225 Appendix F: Getting Help World Wide Web http://support.intel.com/support/motherboards/server/SR9000MK4U . Telephone All calls are billed per incident, levied in local currency at the ap plicable credit card exchange rate plus applicable taxes. (Intel reserves the right to change the pricing for telephone support at any time without notice). Bef[...]

226 Intel ® Server System SR9000MK4U Product Guide In Asia-Pacific Region Australia .... 1800 64 9931 Cambodia .. 63 2 636 9797 (via Phili ppines) China ......... 800 820 1 100 (toll-free) ................... . 8 621 33104691 (not toll-free) Hong Kong 852 2 844 4456 India ........... 0006517 2 68303634 (manual toll-free. Y ou need an IDD-equipped [...]

Intel ® Server System SR9000MK4U Product Guide 227 Colombia ... Contact A T&T USA at 01 800 91 1 0010. Once connected, dial 800 843 4 481 Costa Rica . Contact A T&T USA at 0 800 0 1 14 1 14. Once connected, dial 800 84 3 4481 Ecuador (Andimate) .... Contact A T&T USA at 1 999 1 19. Once connected, dial 800 843 4 481 (Pacifictel) ..... [...]

228 Intel ® Server System SR9000MK4U Product Guide[...]

229 Appendix G: Regulatory and Compliance Information T o ensure regulatory complian ce, you must adhere to the assembly instructions in this guide to ensure and maintain compliance with existing product certifi cations and approvals. Use only the des cribed, regulated components specified in this guide. Use of other products / components will void[...]

230 Intel ® Server System SR9000MK4U Product Guide • GS License (Germany) • GOST R 50377-92 - License (Russia) • Belarus License (Belarus) • Ukraine License (Ukraine) • CE - Low V oltage Directive 73/23/EEE (Europe) • IRAM Certification (Ar gentina) • GB4943- CNCA Certification (China) Product EMC Compliance - Class A Compliance Note[...]

Intel ® Server System SR9000MK4U Product Guide 231 • C-T ick Declaration of Conformity (Australia) • MED Declaration of Conformity (New Zealand) • BSMI Certification (T aiwan) • GOST R Certification / License (Russia) • Belarus Certification / License (Belarus) • RRL Certification (Korea) • IRAM Certification (Argentina) • CNCA Cer[...]

232 Intel ® Server System SR9000MK4U Product Guide Any changes or modifications not expressly ap proved by the grantee of th is device could void the user's authority to operate the eq uipment. The customer is responsible for ensuring compliance of the modified product. Only peripherals (computer input/output devices, terminals, printers, etc[...]

Intel ® Server System SR9000MK4U Product Guide 233 BSMI (Taiwan) The BSMI Certification Marking and EMC warnin g is located on the outside rear area of the produc t. RRL (Korea) English translation of the notice above: 1. T ype of Equipment (Model Name): On License and Product 2. Certification No.: On RRL certificate. Obtain certificate from local[...]

234 Intel ® Server System SR9000MK4U Product Guide Regulated Specified Components T o maintain the UL listing and complian ce to other regula tory certifications and/or declarations, the following regu lated components must be used and conditions adhered to. Interchanging or use of other component w ill void the UL listing and other product certif[...]

Intel ® Server System SR9000MK4U Product Guide 235 Restriction of Hazardous Substances (RoHS) Compliance Intel has a system in place to restrict the use of banned subs tances in accordance with the European Di rective 2002/95 /EC. Compliance is b ased on decl aration that m aterials banned in the RoHS Directive are either (1) be low all applicable[...]

236 Intel ® Server System SR9000MK4U Product Guide[...]