LG Electronics WD(M)-80130F Bedienungsanleitung

W ASHING MACHINE SER VICE MANUAL READ THIS MANUAL CAREFULL Y TO DIAGNOSE TROUBLE CORRECTL Y BEFORE OFFERING SERVICE. website : http://www .LGEservice.com e-mail : http://LGEservice.com/techsup.html MODEL : WD(M)-65130F WD(M)-80130F WD(M)-10130(5)F WD(M)-10131F CAUTION[...]

CONTENTS 1. SPECIFICA TION ............................................................................................................................3 2. FEA TURES & TECHNICAL EXPLANA TION ................................................................................ 4 3. P AR TS IDENTIFICA TION .............................................[...]

3 1. SPECIFICA TION ITEM WD(M)-65130F , WD(M)-80130F , WD(M)-10130(1, 5)F POWER SUPPL Y 220-240V~, 50Hz PRODUCT WEIGHT 67kg W ASHING 190W SPIN (800rpm) 450W DRAIN MOTOR 32W W ASH HEA TER 2000W W ASH 45rpm SPIN WD(M)-65130F 400/500/650 rpm WD(M)-80130F 400/600/800 rpm WD(M)-10130(1, 5)F 400/800/1000 rpm OPERA TION W A TER PRESSURE 0.3-10kgf/cm 2 (30[...]

Jumbo drum LG’s jumbo drum can wash about 40% more per load than conventional washing machine. A bigger drum improves the wash performance. Protection against wrinkles With the alternate rotation of the drum, wrinkling in the laundry is minimized. More economical by Fuzzy Logic System FUZZY Logic System detects the amount of load and water temper[...]

2-2.DETERMINE W ASHING TIME BY FUZZY LOGIC T o get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. 2-3.W A TER LEVEL CONTROL This model adopts a pressure sensor which can sense the water level in the tub. When the water level reaches to the preset level the wa[...]

3. P AR TS IDENTIFICA TION 6 Drain hose Wrench Power plug Control panel Door Lower cover Adjustable feet (For detergent and fabric softener) Drawer Drum Lower cover cap Drain pump filter Drain plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard.[...]

Before servicing ask the customer what the trouble is. Check the adjustment (power supply is 220-240V , remove the transit bolts....) Check the troubles referring to the troubleshooting. Decide service steps referring to disassembly instructions. Then, service and repair . After servicing, operate the appliance to see whether it works O K or NOT . [...]

HOW TO CONNECT INLET HOSE Check that the rubber washer is inside of the valve connector . Connect the inlet hose firmly to prevent leak. CONNECT DRAIN HOSE CONNECT POWER PLUG 8 Make sure that the hose is not twisted. The drain hose should be placed under 100cm from the floor . Connect the power plug to the wall outlet. Avoid connecting several elec[...]

TEST OPERA TION 9 Connect the power plug to In case of cotton program. the outlet. Connect the inlet hose. Preparation for Press the power button. Press the ST AR T/P AUSE washing. button. Check if the drum rotates Check if water is supplied clockwise and counterclockwise. through the detergent dispenser . Power off and then power on. Check if the [...]

10 5. OPERA TION Start/Pause button Use the button to start or pause wash cycle. The power turn off automatically 4 minutes after the pause button is pressed. Spin WD(M)-10130(1, 5)F No Spin ➔ Rinse Hold ➔ 400 ➔ 800 ➔ 1000 WD(M)-80130F No Spin ➔ Rinse Hold ➔ 400 ➔ 600 ➔ 800 WD(M)-65130F No Spin ➔ Rinse Hold ➔ 400 ➔ 500 ➔ 650[...]

11 Rinse Hold No Spin 400 800 1000 Cold 30 40 60 95 ˚ C Time Save Pre W ash Crease Care Rinse+ Spin T emp. Option Option Rinse+ : If you wish to rinse more, the Rinse+ option will remove any trace of detergents. Crease Care : If you want to prevent crease, select this function after selecting spin speed. W ater temperatur e selector Press the butt[...]

12 Start/Pause button Use the button to start or pause wash cycle. The power turn off automatically 4 minutes after the pause button is pressed. Spin WD(M)-10130(1, 5)F No Spin ➔ Rinse Hold ➔ 400 ➔ 800 ➔ 1000 WD(M)-80130F No Spin ➔ Rinse Hold ➔ 400 ➔ 600 ➔ 800 WD(M)-65130F No Spin ➔ Rinse Hold ➔ 400 ➔ 500 ➔ 650 W ash pr ogra[...]

13 Rinse Hold No Spin 400 800 1000 Cold 30 40 60 95 ˚ C Time Save Pre W ash Crease Care Rinse+ Spin T emp. Option Option Rinse+ : If you wish to rinse more, the Rinse+ option will remove any trace of detergents. Crease Care : If you want to prevent crease, select this function after selecting spin speed. W ater temperatur e selector Press the butt[...]

14 6. WIRING DIAGRAM / PROGRAM CHAR T * Water Supply : WÆ S * Intermittent Spin : I Æ S * Disentangle : D Æ T * Basic Cycle * Optional Cycle * Pre-Setting Time : Water Supply - 120 sec. * Basic time is minute in washing chart Drain - 60 sec. * The actual program time can be varied with the load amount, * ~ Time for varies as the temperature or t[...]

7. TROUBLESHOOTING 7-1. BEFORE PERFORMING SER VICE ■ Be careful of electric shock or disconnecting the parts while troubleshooting. ■ V oltage of each terminal in 220-240V~ and DC while applying an electric current. 7-2. QC TEST MODE. ① Pressing T emp, and Option button simultaneously . ② Power supply ON with pressing upper two button. ③ [...]

ERROR SYMPTOM 1 W A TER INLET W ater has not reached to the pre-set level within 4 min. since ERROR inlet valve operated, or water has not reached to the normal level within 25 min. 2 IMBALANCE The appliance is tilted. ERROR Laundry is gathered to one side. Non distributable things are put into the drum. 3 DRAIN ERROR W ater has not drained enough [...]

SYMPTOM GUIDE FOR SERVICE CALL NO POWER W ater inlet trouble 17 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERA TION 8. ERROR DIAGNOSIS AND CHECK LIST YES YES YES NO NO YES NO NO Is the power plug connected firmly to 220-240V~ outlet? Power failure? or Breaker opened? Is the outlet controlled by a switch. Visit to check Is displayed? Is the tap opened?[...]

18 SYMPTOM GUIDE FOR SERVICE CALL DOOR OPEN ERROR Refer to 7-3 ERROR DISPLA Y Drain T rouble NO YES YES NO NO YES Did you press the Start/Pause button when the door is open? Visit to check Check if the door switch is O.K Is displayed? Is the debris filter clogged with foreign material such as pins, coins, etc.? Is the drain hose frozen with water ,[...]

19 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener YES YES YES YES YES Is low-sudsing detergent for the durm washing machine used? Is the proper amount of detergent used as recommended? Recommend to reduce the amount of detergent. Is softener put in th[...]

20 8-2.FAUL T DIAGNOSIS AND TROUBLESHOOTING 1. Be careful of electric shock or disconnecting the parts while troubleshooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the PWB assembly (Main), put in the connectors correctly . CAUTION NO NO YES YES PWB ASSEMBLY 1 NO NO YES YES Check the fuse?[...]

21 NO YES NO YES NO YES NO NO YES YES YES NO NO NO YES Wiring diagram option (HOT) option (HOT) MAX max Is the water supply shut-off? Is the tap opened? Is the inlet valve filter clogged with impurity? Is resistance of the inlet valve connector between the 2 to 8 k ? Check the voltage between each terminals of inlet V alve is 220 - 240V~. (Refer to[...]

22 YES YES YES NO NO NO NO NO YES YES YES YES Wiring diagram option (HOT) MAX max ABNORMAL SOUND SOFTENER DOES NOT FLOW IN Fix the bolt tightly . Replace the V -belt (4400FR31 16A) Replace the motor . Refer to NO W A TER SUPPL Y Check the wiring on the dispenser . Put it in the correct compartment. Clean the cap and drawer . Is the pulley bolt loos[...]

23 YES YES NO NO NO NO YES YES NO PWB ASSEMBLY PWB ASSEMBLY YES NO 1 2 Clean the air chamber and hose. Replace the sensor . (pressure) Repair drain hose Remove foreign material. Reconnect or repair the connector Replace the pump assembly Replace the PWB Are there any problem at air chamber , the hose or pressure sensor? Replace the PWB assembly . I[...]

24 NO YES YES WASH HEATER TROUBLE 4 1 AC 220-240V NO NO YES NO YES (1) Replace the thermistor (6322FR2046B) Push the thermistor tightly to the rubber . When disconnect the connector (1) on the PWB assembly is the resistance of the Natural connectors ( White), (Blue / White) between 2.5 k to 180 k (105 ~0 )? When checking thermistor on the tub, is t[...]

25 3 4 2 1 1 10 12 3 4 5 6 7 8 9 10 5 YES YES YES NO NO NO YES T emp. Option SPIN TROUBLE Normal. Reconnect or repair it. Replace the motor assembly . (4681FR1 194A) or (4681FR1 194B) Check the sensor (Pressure) or hose (Sensor). If the problem is on the sensor or the hose, replace the sensor or the hose. Press Power button with both T emp. and Opt[...]

26 Be sure to unplug the machine out of the outlet before disassembling and repairing the parts. 9. DISASSEMBL Y INSTRUCTIONS Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward as shown. Disconnect the PWB Assembly connector from Main lead wire Assembly . Pull out the drawer and unscrew 2 screws. Push upper hooks [...]

27 Disassemble the top plate assembly . Pull out the drawer to arrow direction. Unscrew 2 screws. The hose clamps and the hose are disassembled. The ventilation bellows and the water inlet bellows are disassembled on the tub. Option DISPENSER ASSEMBL Y DISPENSOR ASSEMBL Y DRA WER[...]

28 Disconnect the wiring receptacle. Unscrew 2 screws from the back. When reconnecting the connector Open the lower cover plate by using coin and pull out the lower cover in the arrow direction after a screw is unscrewed. Open the door completely . Remove the two screws from the hinge. When removing the door assembly , it is necessary to hold the b[...]

29 T ake apart the cabinet gasket clamp. Unscrew 2 screws from the cabinet cover . Open the lower cover cap and unscrew 1 screw inside. T ake apart the lower cover . Unscrew all the screws on the upper and lower sides of the cabinet cover . T ake apart the tub gasket clamp. Make sure that the drain hole of the gasket is put beneath when reassemblin[...]

30 Remove the back cover . T ake off the belt turning the pulley . Unscrew the bolt to pull out the pulley . Unscrew 2 screws from the bracket. Push the motor in the arrow direction for disassembling. When reassembling the motor , make sure that motor mounting bushings are not taken off from the bracket. Pull out the hinge, pressing its snap. Do no[...]

Cap (Remaining Hose) Screw Pump Outlet Hose Tub Pump Bellows 31 Remove pump outlet hose. Remove tub pump bellows. Remove cap (Remaining Hose.) Disconnect the wiring. Unscrew 2 screws. Remove the pump. Loosen the M6 heater nut to pull out the heater . When mounting the heater , be sure to insert the heater into the heater clip on the bottom of the t[...]

32 SWITCH ASSEMBL Y , DOOR LOCK WHEN FOREIGN MA TERIAL IS STUCK BETWEEN DRUM AND TUB T ake apart the cabinet cover clamp and release the gasket. Unscrew 2 screws holding the door lock. Disconnect the door lock from the wiring connector . Remove the heater . Remove the foreign material (wire, coin and others) by inserting a long bar through the hole[...]

10-1.THE EXPLODED VIEW OF CABINET ASSEMBL Y 33 10. EXPLODED VIEW A485 A480[...]

10-2 THE EXPLODED VIEW OF CONTROL P ANEL & DISPENSER ASSEMBL Y 34 F430 A450[...]

10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBL Y 35[...]

Mar . 2002 PRINTED IN KOREA P/No.:3828ER3013A[...]