Siemens 440 Bedienungsanleitung

MICROMASTER 440 Parameter List Issue 01/06 User Documentation 6SE6400-5BB00-0BP0[...]

Available Documentation for the MICROMASTER 440 Getting Started Guide Is for quick commissioning with SDP an d BOP. Operating Instructions Gives information about features of the MICROMASTER 440, Installation, Commissioning, Control modes, Syst em Parameter structure, Troublesh ooting, Specifications and available options of the MICROMASTER 440. Pa[...]

MICROMASTER 440 Parameter List User Documentation Valid for Issue 01/06 Converter Type Software Version MICROMASTER 440 V2.1 Issue 01/06 Block Diagram and Terminals Parameter List Function Diagrams Faults and Alarms Abbreviations[...]

Notes Issue 01/06 MICROMASTER 440 Parameter List 4 6SE6400-5BB00-0BP0 Warning Please refer to all Definitions an d Warnings containe d in the Operating Instructions. You will find the Operating Instructions on the Docu CD delivered with your inverter. If the CD is lost, it can be ordered via your local Siem ens department under the Order No. 6SE640[...]

Issue 01/06 Table of Contents MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 5 Parameters MICROMASTER 440 This Parameter List must only be use d together with the Operating Instructions o f the MICROMASTER 440. Please pay special attention to the Warnin gs, Cautions, Notices and Notes contained in these manual s. Table of Contents 1 Block Diagra[...]

Table of Contents Issue 01/06 MICROMASTER 440 Parameter List 6 6SE6400-5BB00-0BP0 3.21 Ramp-function generator....................................................................... 131 3.22 Flying restart .......................................................................................... 136 3.23 Automatic restart ..........................[...]

Issue 01/06 Block Diagram and Terminals MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 7 1 Block Diagram and T erminals 1.1 Block Diagram PE 1/3 AC 200 - 240 V 3 AC 380 - 480 V 3 AC 500 - 600 V SI PE L/L1, N/L2 L/L1, N/L2,L3 L1, L2, L3 = 3 ~ PE U,V,W M 12 ADC 1 ADC 2 12 60 Hz 50 Hz A/D A/D +10 V 0 V 0 - 20 mA max . 500 Ω NPN PNP CPU RS485 D/A [...]

Block Diagram and Terminals Issue 01/06 MICROMASTER 440 Parameter List 8 6SE6400-5BB00-0BP0 1.2 Power T erminals You can gain access to the mains an d motor terminals by removing the front covers. Fig. 1-1 Frame Size A - F[...]

Issue 01/06 Block Diagram and Terminals MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 9 Shield connection Mains cable PE Hoisting eyes Mains cable Phase U1/L1, V1/L2, W1/L3 T op adjustment rail Bottom adjustment rail Status Display Panel Shield connection control leads T ransformer adaption Motor cable Phase U2, V2, W2 Motor cable PE Shield con[...]

Block Diagram and Terminals Issue 01/06 MICROMASTER 440 Parameter List 10 6SE6400-5BB00-0BP0 Cable opening for mains conection U1/L1, V1/L2, W1/L3 Shield connection Mains cable PE Hoisting eyes C able opening DCP A, DCNA for connection of an external braking unit Mains cable Phase U1/L1, V1/L2, W1/L3 T op adjustment rail Bottom adjustment rail Stat[...]

Issue 01/06 Block Diagram and Terminals MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 11 1.3 Control T erminals Terminal De signation Function 1 - Output +10 V 2 - Output 0 V 3 ADC1+ Analog input 1 (+) 4 ADC1- Analog input 1 (-) 5 DIN1 Digital input 1 6 DIN2 Digital input 2 7 DIN3 Digital input 3 8 DIN4 Digital input 4 9 - Isolated output +24 V[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 12 6SE6400-5BB00-0BP0 2 Parameters 2.1 Introduction to MICROMASTER System Parameters The layout of the parameter description is as follows. 1 Par number 2 Parameter name 9 Min: [index] 3 CStat : 5 Datatype 7 Unit: 10 Def: 4 P-Group: 6 active: 8 Quick Com m: 11 Max: 13 Description: 1. Parameter n[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 13 3. CStat Commissioning status of the parameter . Three states are possible: Commissioning C Run U Ready to r un T This indicates when the parameter can b e changed. One, two or all three st ates may be specified. If all three states are specified, this mean s that it is pos[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 14 6SE6400-5BB00-0BP0 13. Description The parameter descriptio n consists of the sections an d contents listed below. Some of these sections and contents are optional an d will be omitted on a case- to-case basis if not applicable. Description : Brief explanation of the parameter function. Diagr[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 15 2.2 Quick commissioning (P0010 = 1) The following parameters are ne cessary for quick commissioni ng (P0010 = 1). Quick commissioning (P0010 = 1) Par.-No. Name Access level Cstat P0100 Europe / North America 1 C P0205 Inverter application 3 C P0300 Select motor type 2 C P03[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 16 6SE6400-5BB00-0BP0 Seven-segment display The seven-segment display is structure d as follows: 1 0 3 2 5 4 7 6 9 8 11 10 13 12 15 14 Segment Bit Segme nt B it The significance of the relevant bits in the display is described in t he status and control word parameters.[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 17 2.3 Command and Drive Dat aset s - Overview Command Datasets (CDS) ParNo Parameter text 1) P0700[3] Selection of command source X P0701[3] Function of digital input 1 X P0702[3] Function of digital input 2 X P0703[3] Function of digital input 3 X P0704[3] Function of digita[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 18 6SE6400-5BB00-0BP0 Drive Datasets (DDS) ParNo Parameter text P0005[3] Display selection r0035[3] CO: Act. moto r temperature P0291[3] Inverter protection P0300[3] Select motor type P0304[3] Rated motor voltage P0305[3] Rated motor current P0307[3] Rated motor power P0308[3] Rated motor cosPhi[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 19 ParNo Parameter text P1013[3] Fixed frequency 13 P1014[3] Fixed frequency 14 P1015[3] Fixed frequency 15 P1031[3] Setpoint memory of the MOP P1040[3] Setpoint of the MOP P1058[3] JOG frequency ri ght P1059[3] JOG frequency left P1060[3] JOG ramp-up time P1061[3] JOG ramp-do[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 20 6SE6400-5BB00-0BP0 ParNo Parameter text P1580[3] Efficiency optimization P1582[3] Smooth time for flux setpoint P1596[3] Int. time field weak. controller P1610[3] Continuous torque boost (SLVC) P1611[3] Acc. torque boost (SLVC) P1654[3] Smooth time for Isq setpoint P1715[3] Gain current contr[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 21 2.4 Binector Input Parameters ParNo Parameter text P0731[3] BI: Function of digital output 1 P0732[3] BI: Function of digital output 2 P0733[3] BI: Function of digital output 3 P0800[3] BI: Download parameter set 0 P0801[3] BI: Download parameter set 1 P0810 BI: CDS bit 0 ([...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 22 6SE6400-5BB00-0BP0 2.5 Connector Input Parameters ParNo Parameter text P0095[10] CI: Display PZD signals P0771[2] CI: DAC P1070[3] CI: Main setpoint P1071[3] CI: Main setpoint scaling P1075[3] CI: Additional setpoint P1076[3] CI: Additional setpoint scaling P1330[3] CI: Voltage setpoint P1478[...]

Issue 01/06 Parameters MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 23 2.7 Connector Output Parameters ParNo Parameter text r0020 CO: Freq. setpoint before RF G r0021 CO: Act. filtered frequency r0024 CO: Act. filtered output freq. r0025 CO: Act. filtered output voltage r0026 CO: Act. filtered DC-link volt. r0027 CO: Act. filtered output curre[...]

Parameters Issue 01/06 MICROMASTER 440 Parameter List 24 6SE6400-5BB00-0BP0 ParNo Parameter text r1597 CO: Outp. field weak. controller r1598 CO: Flux setpoint (total) r1718 CO: Output of Isq controller r1719 CO: Integral output of Isq ctrl. r1723 CO: Output of Isd controller r1724 CO: Integral output of Isd ctrl. r1725 CO: Integral limit of Isd ct[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 25 3 Parameter Description Note Level 4 Parameters are not visible with BOP or AOP. 3.1 Common p arameters r0000 Drive display Min: - Datatype: U16 Unit : - Def: - P-Group: ALWAYS Max: - Displays the user selected output as defined in P0005. Note: Pressing the "[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 26 6SE6400-5BB00-0BP0 Dependency: The parameters are sub-divided into groups (P-Group) according t o their functionality. This increases the transparency and allows a parame ter to be quickly searched for. Furthermore, pa rameter P0004 can be used to control the ability to be visualiz[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 27 P0010 Commissioning parameter Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: ALWAYS Act i ve : first confirm QuickComm.: No Max: 30 Filters parameters so that only those related to a particular functional group are selected. Possible Settings: 0 Ready 1 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 28 6SE6400-5BB00-0BP0 Index: P0013[0] : 1st user parameter P0013[1] : 2nd user parameter P0013[2] : 3rd user parameter P0013[3] : 4th user parameter P0013[4] : 5th user parameter P0013[5] : 6th user parameter P0013[6] : 7th user parameter P0013[7] : 8th user parameter P0013[8] : 9th u[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 29 3.2 Diagnosis p arameters r0018 Firmware version Min: - Datatype: Float Unit : - Def: - P-Group: INVERTER Max: - Displays version number of installed firmware. r0019 CO/BO: BOP control w ord Min: - Datatype: U16 Unit : - Def: - P-Group: COMMANDS Max: - Displays s[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 30 6SE6400-5BB00-0BP0 r0024 CO: Act. filtered outp ut freq. Min: - Datatype: Float Unit : Hz Def: - P-Group: CONTRO L Max: - Displays actual output frequency. Slip compensation, resonance damping and frequenc y limitation are included. r0025 CO: Act. filtered outp ut voltage Min: - Da[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 31 r0031 CO: Act. filtered torque Min: - Datatype: Float Unit : Nm Def: - P-Group: CONTRO L Max: - Displays electrical torque. i Z L L 2 3 m sq rd p R m M ⋅ Ψ ⋅ ⋅ ⋅ = : m M : L m : L R : rd Ψ : Z p : i sq : e Motor tor que Pol e pair number Rotor flux Roto[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 32 6SE6400-5BB00-0BP0 r0036 CO:Inverter ov erload utilization Min: - Datatype: Float Unit : % Def: - P-Group: INVERTER Max: - Displays inverter overload utilization calculated via I2t model. The actual I2t value relative to the max. possible I2t value supplies utilization in [%]. If t[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 33 P0040 Reset energy consumption meter Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: INVERTER Act i ve : first confirm QuickComm.: No Max: 1 Resets value of parameter r0039 (energy consum ption meter) to zero. Possible Settings: 0 No reset 1 Reset r0039 t[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 34 6SE6400-5BB00-0BP0 r0052 CO/BO: Act. status word 1 Min: - Datatype: U16 Unit : - Def: - P-Group: COMMANDS Max: - Displays first active status word of inverter (bit format) and can be used to diagnose inverter status. Bitfields: Bit00 Drive ready 0 NO 1 YES Bit01 Drive ready to run [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 35 t r 0054 Bit 0 0 ON / OF F 1 ON t r 0054 Bit 1 1 Rev ers e 0 t f ac t t r 0052 Bit 0 2 Dr iv e r unning t r 0052 Bit 1 4 M ot or ru n s r ight lef t not defined las t state i s di spl ayed r 0052 Bi t14 " Motor r uns r ight " ==> se e be lo w Details[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 36 6SE6400-5BB00-0BP0 f t t f OF F ON t ac t f se t 0 1 r 0053 Bit 0 9 Ramping fi nis hed r 0053 Bi t 09 "R ampi ng fi nis hed" ==> se e be lo w Details: See description of seven-segment display given in the "Introduction to MICROMASTER System Parameters" in thi[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 37 r0056 CO/BO: Status of motor control Min: - Datatype: U16 Unit : - Def: - P-Group: CONTRO L Max: - Displays status of motor control (MM420: V/f status), which can be used to diagnose inverter status. Bitfields: Bit00 Init. control finished 0 NO 1 YES Bit01 Motor [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 38 6SE6400-5BB00-0BP0 r0064 CO: Dev. frequency controller Min: - Datatype: Float Unit : Hz Def: - P-Group: CONTRO L Max: - Displays actual deviation of speed controller. This value is calculated from the frequency setpoint (r0062) and the actual frequency (r0063). Dependency: Applies [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 39 r0070 CO: Act. DC-link voltage Min: - Datatype: Float Unit : V Def: - P-Group: INVERTER Max: - Displays (unfiltered) DC-link voltage. Note: Used for process control purposes (in contrast to r0026 (actual DC-link voltage), which is filtered and is used to display [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 40 6SE6400-5BB00-0BP0 r0075 CO: Current setp oint Isd Min: - Datatype: Float Unit : A Def: - P-Group: CONTRO L Max: - Displays setpoint of flux generating current component. Dependency: Applies when vector control is selected in P1300 (control mode); otherwise, the display shows the v[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 41 P0095[10] CI: Display PZD signals Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: No Max: 4000:0 Selects source of display for PZD signals. Index: P0095[0] : 1st PZD signal P0095[1] : 2nd PZD signal P0095[[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 42 6SE6400-5BB00-0BP0 3.3 Inverter p arameters (HW) P0100 Europe / North America Min: 0 CStat: C Datatype: U16 Unit : - Def: 0 P-Group: QUICK Act i ve: first confirm QuickComm.: Yes Max: 2 Determines whether power settings (e.g. nominal rating plate po wer - P0307) are expressed in [k[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 43 r0200 Act. power stack code number Min: - Datatype: U32 Unit : - Def: - P-Group: INVERTER Max: - Identifies hardware variant as shown in table below. 41 6SE 6440- 2U C 11- 2A A x 1/ 3A C 200-240V + 10% - 10% 47-63H z 0,12 0,12 no A 42 6SE 6440- 2U C 12- 5A A x 1/[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 44 6SE6400-5BB00-0BP0 Code- No . MM440 MLF B Input Vol tage & F r equency CT Powe r kW VT Pow e r kW Inter nal Fi l t er Fram e Siz e 94 6SE 6440- 2A D 25- 5C A x 3A C 380- 4 80V +10% - 10% 47- 63H z 5,5 7,5 C l. A C 95 6SE 6440- 2A D 27- 5C A x 3A C 380- 4 80V +10% - 10% 47- 63H [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 45 r0204 Power stack features Min: - Datatype: U32 Unit : - Def: - P-Group: INVERTER Max: - Displays hardware features of power stack. Bitfields: Bit00 DC input voltage 0 NO 1 YES Bit01 RFI filter 0 NO 1 YES Note: Parameter r0204 = 0 indicates that no power stack ha[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 46 6SE6400-5BB00-0BP0 It is recommended to modify P0205 first. Afterwards motor paramet er may be adapted. Motor param eter will be overridden by changing this sequence. r 0207 I r 0208 P r 0209 I Inve r ter par ameter s I, n I, n I, m ax P0305 I P0307 P P0640 I Motor par ameter s M, [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 47 r0209 Maximum inverter current Min: - Datatype: Float Unit : A Def: - P-Group: INVERTER Max: - Displays maximum output current of inverter. Dependency: Parameter r0209 depends on the derating which is affected by pulse frequenc y P1800, ambient temperature and al[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 48 6SE6400-5BB00-0BP0 P0290 Inverter overload reaction Min: 0 CStat: CT Datatype: U16 Unit : - Def: 2 P-Group: INVERTER Act i ve : first confirm QuickComm.: No Max: 3 Selects reaction of inverter to an internal over-temperature. Following physical values influence the inverter overloa[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 49 P0292 Inverter temperature w arning Min: 0 CStat: CUT Datatype: U16 Unit : °C Def: 5 P-Group: INVERTER Act i ve : first confirm QuickComm.: No Max: 25 Defines the temperature difference (in ºC) bet ween the Overtemperature trip threshold and the warning thresho[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 50 6SE6400-5BB00-0BP0 3.4 Motor p a rameters P0300[3] Select motor ty pe Min: 1 CStat: C Datatype: U16 Unit : - Def: 1 P-Group: MOTOR Act i ve : first confirm QuickComm.: Yes Max: 2 Selects motor type. This parameter is required during commissioning to select motor type and optimize i[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 51 P0304[3] Rated motor voltage Min: 10 CStat: C Datatype: U16 Unit : V Def: 230 P-Group: MOTOR Act i ve : first confirm QuickComm.: Yes Max: 2000 Nominal motor voltage [V] from rating plate. Following diagram shows a typical rating plate with the locations of the r[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 52 6SE6400-5BB00-0BP0 NEMA Mo t o r T 1 T 4 T 7 T 3 T 6 T 9 T 8 T 5 T 2 Vol t s UV W T 1 -T 7 T 2 -T 8 T 3 -T 9 low T 4 -T 5 -T 6 T 1 T 2 T 3 high Connected together Connecti on T 1 -T 7 T 2 -T 8 T 3 -T 9 Y Y Y UV W T 1 -T 6 -T 7 T 2 -T 4 -T 8 T 3 -T 5 -T 9 - T 1 T 2 T 3 T 4 -T 7 T 5 [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 53 P0308[3] Rated motor cosPhi Min: 0.000 CStat: C Datatype: Float Unit : - Def: 0.000 P-Group: MOTOR Act i ve : first confirm QuickComm.: Yes Max: 1.000 Nominal motor power factor (cosPhi) from rating plate - see diagra m P0304. Index: P0308[0] : 1st. Drive data se[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 54 6SE6400-5BB00-0BP0 r0313[3] Motor pole pairs Min: - Datatype: U16 Unit : - Def: - P-Group: MOTOR Max: - Displays number of motor pole pairs that the inverter is currentl y using for internal calculations. Index: r0313[0] : 1st. Drive data set (DDS) r0313[1] : 2nd. Drive data set (D[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 55 r0332[3] Rated power factor Min: - Datatype: Float Unit : - Def: - P-Group: MOTOR Max: - Displays power factor for motor Index: r0332[0] : 1st. Drive data set (DDS) r0332[1] : 2nd. Drive data set (DDS) r0332[2] : 3rd. Drive data set (DDS) Dependency: Value is cal[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 56 6SE6400-5BB00-0BP0 P0340[3] Calculation of motor par ameters Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: MOTOR Act i ve : first confirm QuickComm.: No Max: 4 Calculates various motor parameters (see table below). This param eter is required during commissioning to optim[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 57 P0341[ 3] Motor inert ia [k g*m^2] P0344[ 3] Motor w eight P1521[ 3] CO: Lower tor que l imi t P1531[ 3] Regener ativ e power li mitati on P2002[ 3] Refer ence c ur r ent P2174[ 3] T or que threshol d M _t hr esh P2186[ 3] Lower t or que thr es hold 1 P0342[ 3] T[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 58 6SE6400-5BB00-0BP0 P0341[3] Motor inertia [kg*m^2] Min: 0.00010 CStat: CUT Datatype: Float Unit : - Def: 0.00180 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 1000.00000 Sets no-load inertia of motor. Together with P0342 (inertia ratio total/motor) and P1496 (scaling [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 59 P0347[3] Demagnetization time Min: 0.000 CStat: CUT Datatype: Float Unit : s Def: 1.000 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 20.000 Defines the de-magnetization time for the connected induction motor. The de-magnetization time is the time t[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 60 6SE6400-5BB00-0BP0 P0352[3] Cable resistance Min: 0.0 CStat: CUT Datatype: Float Unit : Ohm Def: 0.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 120.0 Describes cable resistance between inverter and motor for one phase. d M l l : Cable l ength d : Cable di ameter A [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 61 P0360[3] Main inductance Min: 0.0 CStat: CUT Datatype: Float Unit : - Def: 10.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 3000.0 Sets main inductance [mH] of the motor equivalent circuit (phase value), see diagram below. 1000 0360 P 0310 P 2 L f[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 62 6SE6400-5BB00-0BP0 Co n versio n : T - eq u ivalen t curcu it -- > L L 1 k m R R σ σ + = k L L R m m σ Γ = k R R 2 R R R σ Γ = k L L L R R S σ σ σ σ + = Co n versio n : L L 0.5 1 L L ) k 1 ( 1 k m m Γ σ Γ σ σ Γ σ ⋅ + = ⋅ − + = k R R 2 σΓ R Γ R ⋅ = L 5[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 63 P0364[3] Magnetizing curv e flux 3 Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 115.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 300.0 Specifies third flux value of saturation characteristic in [%] relative to rated motor voltage (P0304). In[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 64 6SE6400-5BB00-0BP0 P0369[3] Magnetizing curv e imag 4 Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 170.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 500.0 Specifies fourth magnetizing current value of saturation characteristic in [%] relative to rated magnetizi[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 65 r0374[3] Rotor resistance [%] Min: - Datatype: Float Unit : % Def: - P-Group: MOTOR Max: - Displays the rotor resistance of the motor equivalent circuit diagram (phase value) as a [%] at the ambient temperature (in the cold state). % 100 P035 8) (1 Z P0360 P035 4[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 66 6SE6400-5BB00-0BP0 r0384[3] Rotor time constant Min: - Datatype: Float Unit : ms Def: - P-Group: MOTOR Max: - Displays calculated rotor time constant [ms]. Index: r0384[0] : 1st. Drive data set (DDS) r0384[1] : 2nd. Drive data set (DDS) r0384[2] : 3rd. Drive data set (DDS) r0386[3][...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 67 3.5 S peed encoder P0400[3] Select encoder ty pe Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: ENCODER Acti ve : Immediately QuickCo mm.: No Max: 2 Selects encoder type (number of encoder channels). Possible Settings: 0 Disabled 1 Single channel encoder[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 68 6SE6400-5BB00-0BP0 r0403 CO/BO: Encoder status word Min: - Datatype: U16 Unit : - Def: - P-Group: COMMANDS Max: - Displays status word of encoder (in bit format). Bitfields: Bit00 Encoder module active 0 NO 1 YES Bit01 Encoder error 0 NO 1 YES Bit02 Signal o.k. 0 NO 1 YES Bit03 Enc[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 69 Note: The value of P0492 should be approx. 2x rated slip, if the motor po wer is less (<=) 90 kW The value of P0492 should be approx. 4x rated slip, if the motor po wer is greater (>) 90 kW P0494[3] Delay freque ncy loss reaction Min: 0 CStat: CUT Datatype:[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 70 6SE6400-5BB00-0BP0 r 0631 AD C 5 V Si gnal loss detec tion T 1 = 4 s 2 1 No sens or PT C KT Y 0 P 0604 F ault F 0015 & P0601 = 2 T her mal motor mode l r 0633 r 0632 r 0035 1 ≥ Motor temp . r eacti on P0610 P0601 Equi val ent c ir cui t data P V, mot Power dis si pation V ϑ [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 71 End temperatur e Ins ulati on cl ass Y A E B F 90 °C 105 °C 120 °C 130 °C 155 °C H 180 °C Ex tract o f IE C 85 The motor overheating disturbance threshold is automatically set by the inverter at 10% higher than th e temperature declared in parameter P0604. [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 72 6SE6400-5BB00-0BP0 P0625[3] Ambient motor temperatu re Min: -40.0 CStat: CUT Datatype: Float Unit : °C Def: 20.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 80.0 Ambient temperature of motor. The paramete r for the stator resistance P0350 and rot or resistance P035[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 73 P0627[3] Overtemperature stator w inding Min: 20.0 CStat: CUT Datatype: Float Unit : °C Def: 80.0 P-Group: MOTOR Act i ve : Immedia tely QuickComm. : No Max: 200.0 Overtemperature of the stator winding. Index: P0627[0] : 1st. Drive data set (DDS) P0627[1] : 2nd.[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 74 6SE6400-5BB00-0BP0 r0633[3] CO: Rotor winding temperature Min: - Datatype: Float Unit : °C Def: - P-Group: MOTOR Max: - Displays rotor winding temperature of motor mass model. Index: r0633[0] : 1st. Drive data set (DDS) r0633[1] : 2nd. Drive data set (DDS) r0633[2] : 3rd. Drive da[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 75 3.8 Command source P0700[3] Selection of command source Min: 0 CStat: CT Datatype: U16 Unit : - Def: 2 P-Group: COMMANDS Act i ve : first confirm QuickComm.: Yes Max: 6 Selects digital command source. Possible Settings: 0 Factory default setting 1 BOP (keypad) 2 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 76 6SE6400-5BB00-0BP0 P0840 722.0 19.0 722.0 2032.0 2036.0 2090.0 P0842 0.0 0.0 0.0 0.0 0.0 0.0 P0844 1.0 19.1 1.0 2032.1 2036.1 2090.1 P0845 19.1 19.1 19.1 19.1 19.1 19.1 P0848 1.0 1.0 1.0 2032.2 2036. 2 2090.2 P0849 1.0 1.0 1.0 1.0 1.0 1.0 P0852 1.0 1.0 1.0 2032.3 2036. 3 2090.3 P07[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 77 3.9 Digit a l input s P0701[3] Function of digital input 1 Min: 0 CStat: CT Datatype: U16 Unit : - Def: 1 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 99 Selects function of digital input 1. DIN ch an n el ( e. g . D IN 1 - PNP ( P0725 = 1)) 24 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 78 6SE6400-5BB00-0BP0 P0702[3] Function of digital input 2 Min: 0 CStat: CT Datatype: U16 Unit : - Def: 12 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 99 Selects function of digital input 2. Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON reverse /OFF1 3 [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 79 P0704[3] Function of digital input 4 Min: 0 CStat: CT Datatype: U16 Unit : - Def: 15 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 99 Selects function of digital input 4. Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON reverse /OFF1 3 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 80 6SE6400-5BB00-0BP0 P0706[3] Function of digital input 6 Min: 0 CStat: CT Datatype: U16 Unit : - Def: 15 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 99 Selects function of digital input 6. Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON reverse /OFF1 3 [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 81 P0708[3] Function of digital input 8 Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 99 Selects function of digital input 8 (via analog input) Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 82 6SE6400-5BB00-0BP0 Index: P0719[0] : 1st. Command data set (CDS) P0719[1] : 2nd. Command data set (CDS ) P0719[2] : 3rd. Command data set (CDS) Note: Using parameter P0719, it is possible to select the command or setpoint sources without changing the BICO connections (this is contr[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 83 P0724 Debounce time for digital inputs Min: 0 CStat: CT Datatype: U16 Unit : - Def: 3 P-Group: COMMANDS Act i ve : Immedia tely QuickComm. : No Max: 3 Defines debounce time (filtering time) used for digital inputs. Possible Settings: 0 No debounce time 1 2.5 ms d[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 84 6SE6400-5BB00-0BP0 3.10 Digit a l outputs r0730 Number of digital outputs Min: - Datatype: U16 Unit : - Def: - P-Group: COMMANDS Max: - Displays number of digital outputs (relays). P0731[3] BI: Function of digital output 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 52:3 P-Grou[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 85 P0732[3] BI: Function of digital output 2 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 52:7 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines source of digital output 2. Index: P0732[0] : 1st. Command data set (CDS) P0732[1] : 2nd. [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 86 6SE6400-5BB00-0BP0 r0747 CO/BO: State of digital outputs Min: - Datatype: U16 Unit : - Def: - P-Group: COMMANDS Max: - Displays status of digital outputs (also includes inversion of digital outputs via P0748). Bitfields: Bit00 Digital output 1 energized 0 NO 1 YES Bit01 Digital out[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 87 r0752[2] Act. input of ADC [V] or [mA] Min: - Datatype: Float Unit : - Def: - P-Group: TERMINAL Max: - Displays smoothed analog input value in volts before the characteristic block. KL 4 KL3 D I P sw it ch A D AD C ty pe AD C sca li n g P07 5 7 P07 5 8 P07 5 9 P0[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 88 6SE6400-5BB00-0BP0 r0755[2] CO: Act. ADC after scal. [4000h] Min: - Datatype: I16 Unit : - Def: - P-Group: TERMINAL Max: - Displays analog input, scaled using ASPmin and ASPmax. Analog setpoint (ASP) from the analog scaling block can vary from min. analog setpoint (ASPmin) to a max[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 89 AD C 1 A DC2 O F F = [V ], 0 - 10 V O N = [A ], 0 - 20 mA 12 34 5 6 789 O F F = [V ], 0 - 10 V O N = [A ], 0 - 20 mA Possible Settings: 0 Unipolar voltage input (0 to +10 V) 1 Unipolar voltage input with monitoring (0 to 10 V) 2 Unipolar current input (0 to 20 mA[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 90 6SE6400-5BB00-0BP0 ASPma x 100 % 10 V V x 100 % % P0760 P0758 P 0757 P0759 P 0756 = 4, P0761 = 0 ASPmin - 10 V 4000 h Index: P0757[0] : Analog input 1 (ADC 1) P0757[1] : Analog input 2 (ADC 2) Note: The ADC-linear characteristic is described by 4 coordinates, based on a two-point e[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 91 P0759[2] Value x2 of ADC scaling [V / mA] Min: -20 CStat: CUT Datatype: Float Unit : - Def: 10 P-Group: TERMINAL Ac ti ve : first confirm QuickComm.: No Max: 20 Sets value of X2 as described in P0757 (ADC scaling). Index: P0759[0] : Analog input 1 (ADC 1) P0759[1[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 92 6SE6400-5BB00-0BP0 ASPmax 100 % 10 V 20 mA V mA x 100 % % P 0760 P 0758 P0757 P0759 ASPm in P0761 4000 h P0761 > 0 an d P 0758 < 0 < P 07 60 The below example produces a -10 to +10 V analog input (-5 0 to +50 Hz) with center zero and a "ho lding point" 0.2 V wide[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 93 3.12 Analog outputs r0770 Number of DACs Min: - Datatype: U16 Unit : - Def: - P-Group: TERMINAL Max: - Displays number of analog outputs available. P0771[2] CI: DAC Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 21:0 P-Group: TERMINAL Ac ti ve : first confirm Qu[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 94 6SE6400-5BB00-0BP0 P0776[2] Type of DAC Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: TERMINAL Ac ti ve : first confirm QuickComm.: No Max: 1 Defines type of analog output. Possible Settings: 0 Current output 1 Voltage output Index: P0776[0] : Analog output 1 (DAC 1) P077[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 95 Note: The DAC-linear characteristic is described by 4 coordinates, based on a two-point equation: 0777 P 07 79 P 0778 P 07 80 P P0777 - x P0778 - y − − = For calculations the point-gradient form (offset and gradient) is more advantageous: 0 y x m y + ⋅ = Th[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 96 6SE6400-5BB00-0BP0 P0781[2] Width of DAC deadband Min: 0 CStat: CUT Datatype: Float Unit : - Def: 0 P-Group: TERMINAL Ac ti ve : first confirm QuickComm.: No Max: 20 Sets width of dead-band in [mA] for analog output. 20 P 0780 y 2 P0778 y 1 P07 7 7 x 1 P0779 x 2 100 % mA P 0781 % I[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 97 3.13 Parameter / command / drive dat a set P0800[3] BI: Do wnload parameter set 0 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines source of command to start download of parameter set[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 98 6SE6400-5BB00-0BP0 P0809[3] Copy command data se t (CDS) Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 2 Calls "copy Command Data Set (CDS)" function. The list of all Command Data Sets (CDS) are shown in the [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 99 The actual active command data set (CDS) is displayed in parameter r005 0. r 0055 Bit 15 r 0054 Bit 1 5 1. CDS 0 0 2. CDS 0 1 3. CDS 1 0 3. CDS 1 1 r 0050 0 1 2 2 se le ct e d CDS ac tiv e CDS Common Settings: 722.0 = Digital input 1 (requires P0701 to be set to [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 100 6SE6400-5BB00-0BP0 P0819[3] Copy driv e data set (DDS) Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 2 Calls "Copy Drive Data Set (DDS)" function. The list of all Drive Data Sets (DDS) are shown in the openi[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 101 The actual active drive data set (DDS) is displayed in parameter r0051[1]. r 0055 Bit 0 5 r 0055 Bit 04 1. DDS 0 0 2. DDS 0 1 3. DDS 1 0 3. DDS 1 1 r 0051 [0] 0 1 2 2 r 0051 [ 1] 0 1 2 2 se le c t e d DDS ac tiv e DDS Common Settings: 722.0 = Digital input 1 (re[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 102 6SE6400-5BB00-0BP0 P0821 BI: DDS bit 1 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4095:0 Selects command source from which Bit 1 for selecting a drive data set is to be read in (see parameter P0820). Common Set[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 103 P0842[3] BI: ON rev erse/OFF1 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Allows ON/OFF1 reverse command source to be selected using BICO. Normally in this case at a positive frequency [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 104 6SE6400-5BB00-0BP0 P0845[3] BI: 2. OFF2 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 19:1 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines second source of OFF2. The first three digits describe the parameter number of the command source and th e last[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 105 P0849[3] BI: 2. OFF3 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 1:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines second source of OFF3. The first three digits describe the parameter number of the command source and th e last [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 106 6SE6400-5BB00-0BP0 P0927 Parameter changeable via Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 15 P-Group: COMM Acti ve : first confirm QuickComm.: No Max: 15 Specifies the interfaces which can be used to change parameters. This parameter allows the user to easily protect the inv[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 107 r0948[12] CO: Fault time Min: - Datatype: U16 Unit : - Def: - P-Group: ALARMS Max: - Time stamp to indicate when the fault has occurred. Index: r0948[0] : Recent fault trip --, time stamp r0948[1] : Recent fault trip --, time stamp r0948[2] : Recent fault trip -[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 108 6SE6400-5BB00-0BP0 P0952 Total number of faults Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: ALARMS Act i ve : first confirm Quick Comm.: No Max: 8 Displays number of faults stored in r0947 (last fault code). Dependency: Setting 0 resets fault history. (changing to 0 al[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 109 r0968 Status w ord 1 Min: - Datatype: U16 Unit : - Def: - P-Group: COMM Max: - Displays active status word of inverter (in binary) and can be used to diagnose which commands are active. Bitfields: Bit00 Drive ready 0 NO 1 YES Bit01 Drive ready to run 0 NO 1 YES [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 110 6SE6400-5BB00-0BP0 3.16 Setpoint source P1000[3] Selection of frequency s etpoint Min: 0 CStat: CT Datatype: U16 Unit : - Def: 2 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: Yes Max: 77 Selects frequency setpoint source. In the table of possible settings below, the main [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 111 Index: P1000[0] : 1st. Command data set (CDS) P1000[1] : 2nd. Command data set (CDS ) P1000[2] : 3rd. Command data set (CDS) Example: Setting 12 selects main setpoint (2) derived from analog input with additional setpoint (1) taken from the motor potentiometer. [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 112 6SE6400-5BB00-0BP0 P1000 = xy y = 0 y = 1 y = 2 y = 3 y = 4 y = 5 y = 6 y = 7 0.0 1050.0 755.0 1024.0 2015.1 2018.1 2050. 1 755.1 P1070 1.0 1.0 1.0 1.0 1. 0 1.0 1.0 1. 0 P1071 0.0 0.0 0.0 0.0 0. 0 0.0 0.0 0. 0 P1075 x = 0 1.0 1.0 1.0 1.0 1. 0 1.0 1.0 1. 0 P1076 0.0 1050.0 755.0 10[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 113 3.17 Fixed frequencies P1001[3] Fixed frequency 1 Min: -650.00 CStat: CUT Datatype: Float Unit : Hz Def: 0.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Defines fixed frequency setpoint 1. There are three options available for selection[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 114 6SE6400-5BB00-0BP0 Direct selection of FF P1001 via DIN 1: P 1 0 1 6 P 0701 = 15 or P0701 = 99, P1020 = 722 .0, P1016 = 1 DIN1 r 1024 r 0722 .0 P1020 1 2, 3 P1001 0 0 P 0702 = 15 or P0702 = 99, P1021 = 722 .1, P1017 = 1 P 1 0 1 7 DIN2 r0722 .1 P1021 1 2,3 P1002 0 0 . . . . + . . .[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 115 P1006[3] Fixed frequency 6 Min: -650.00 CStat: CUT Datatype: Float Unit : Hz Def: 25.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Defines fixed frequency setpoint 6. Index: P1006[0] : 1st. Drive data set (DDS) P1006[1] : 2nd. Drive dat[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 116 6SE6400-5BB00-0BP0 P1012[3] Fixed frequency 12 Min: -650.00 CStat: CUT Datatype: Float Unit : Hz Def: 55.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Defines fixed frequency setpoint 12. Index: P1012[0] : 1st. Drive data set (DDS) P1012[1] : 2nd. Drive d[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 117 P1017[3] Fixed frequency mode - Bit 1 Min: 1 CStat: CT Datatype: U16 Unit : - Def: 1 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 3 Fixed frequencies can be selected in three different modes. Parameter P1017 defines the mode of selection Bit 1.[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 118 6SE6400-5BB00-0BP0 P1021[3] BI: Fixed freq. selection Bit 1 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines origin of fixed frequency selection. Index: P1021[0] : 1st. Command data set (CDS) P1021[1] [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 119 P1027[3] Fixed frequency mode - Bit 5 Min: 1 CStat: CT Datatype: U16 Unit : - Def: 1 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 2 direct selection or direct selection + ON for bit 5 Possible Settings: 1 Direct selection 2 Direct selection + O[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 120 6SE6400-5BB00-0BP0 3.18 Motorized potentiometer (MOP) P1031[3] Setpoint memory of the MOP Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 1 Saves last motor potentiometer setpoint (MOP) that was active before OFF comman[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 121 P1040[3] Setpoint of the MOP Min: -650.00 CStat: CUT Datatype: Float Unit : Hz Def: 5.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Determines setpoint for motor potentiometer control (P1000 = 1). Index: P1040[0] : 1st. Drive data set ([...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 122 6SE6400-5BB00-0BP0 3.19 JOG P1055[3] BI: Enable JOG right Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines source of JOG right. Index: P1055[0] : 1st. Command data set (CDS) P1055[1] : 2nd. Command dat[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 123 P1058[3] JOG frequen cy right Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 5.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Jogging increases the motor frequency by small amounts. The JOG buttons uses a non-latching switch on one [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 124 6SE6400-5BB00-0BP0 P1060[3] JOG ramp-up time Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 10.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 650.00 Sets jog ramp-up time. This is the time used while jogging is active. f ( Hz) t ( s ) f max ( P1082) P1060 t [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 125 3.20 Setpoint channel P1070[3] CI: Main setpoint Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 755:0 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Defines source of main setpoint. Index: P1070[0] : 1st. Command data set (CDS) P1070[1] : [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 126 6SE6400-5BB00-0BP0 P1076[3] CI: Additional setpoin t scaling Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 1:0 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Defines source of scaling for additional setpoint (to be added to main setpoint). Index: P1076[0] :[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 127 P1080[3] Min. frequency Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 0.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: Yes Max: 650.00 Sets minimum motor frequency [Hz] at which motor will run irrespective of frequency setpoint. The minimum frequ[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 128 6SE6400-5BB00-0BP0 P1082[3] Max. frequency Min: 0.00 CStat: CT Datatype: Float Unit : Hz Def: 50.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: Yes Max: 650.00 Sets maximum motor frequency [Hz] at which motor will run irrespective of the frequ ency setpoint. The value s[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 129 r1084 Resultant max. frequenc y Min: - Datatype: Float Unit : Hz Def: - P-Group: CONTRO L Max: - Displays resultant maximum frequency. P1300 < 20 P1800 ≤ 6 k H z → 650.00) , 15 P180 0 (P1082 , min r1084 = P1800 ≥ 8 k H z → 650.00) (P1082, min r1084 = [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 130 6SE6400-5BB00-0BP0 P1094[3] Skip frequency 4 Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 0.00 P-Group: SETPOINT Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Defines skip frequency 4 which avoids effects of mechanical resonance and suppresses frequencies within +/- P1[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 131 P1113[3] BI: Reverse Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 722:1 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines source of reverse command. Index: P1113[0] : 1st. Command data set (CDS) P1113[1] : 2nd. Command data set (CDS[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 132 6SE6400-5BB00-0BP0 P1121[3] Ramp-down time Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 10.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: Yes Max: 650.00 Time taken for motor to decelerate from maximum motor frequency (P1082) do wn to standstill when no rounding i[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 133 P1130[3] Ramp-up initial rounding time Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 0.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 40.00 Defines initial rounding time in seconds as shown on the diagram below. P1133 P1132 P1131 P1130 t [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 134 6SE6400-5BB00-0BP0 P1133[3] Ramp-do w n final rounding time Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 0.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: No Max: 40.00 Defines rounding time at end of ramp-down as shown in P1130 (ramp-up initial roun ding time). In[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 135 P1135[3] OFF3 ramp-do w n time Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 5.00 P-Group: SETPOINT Ac ti ve : first confirm QuickComm.: Yes Max: 650.00 Defines ramp-down time from maximum frequenc y to standstill for OFF3 command. f f max ( P1082) f 2 0 P1[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 136 6SE6400-5BB00-0BP0 3.22 Flying rest art P1200 Flying start Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: FUNC Act i ve : first confirm QuickComm.: No Max: 6 Starts inverter onto a spinning motor by rapidly changing the output frequenc y of the inverter until the actual [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 137 P1202[3] Motor-curre nt: Flying start Min: 10 CStat: CUT Datatype: U16 Unit : % Def: 100 P-Group: FUNC Act i ve : first confirm QuickComm.: No Max: 200 Defines search current used for flying start. Value is in [%] based on rated motor current (P0305). Index: P12[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 138 6SE6400-5BB00-0BP0 r1204 Status word: Flyi ng start V/f Min: - Datatype: U16 Unit : - Def: - P-Group: FUNC Max: - Bit parameter for checking and monitoring states during search, if V/f control mode is selected (see P1300). Bitfields: Bit00 Current applied 0 NO 1 YES Bit01 Current [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 139 3.23 Automatic restart P1210 Automatic restart Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 1 P-Group: FUNC Act i ve : first confirm QuickComm.: No Max: 6 Configures automatic restart function Possible Settings: 0 Disabled 1 Trip reset after power on, P1211 dis[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 140 6SE6400-5BB00-0BP0 0 −−−−− 1 −− 2 + −−− 3 ++++ 4 ++ −− − 5 + − ++ 6 ++++ + F ault ac knowl . F ault ac knowl . F ault ac knowl . F ault ac knowl . F ault ac knowl . F ault ac knowl . re s ta rt re s ta rt re s ta rt re s ta rt re s ta rt F ault ac knowl[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 141 3.24 Motor holding brake P1215 Holding brake enable Min: 0 CStat: T Datatype: U16 Unit : - Def: 0 P-Group: FUNC Act i ve : first confirm QuickComm.: No Max: 1 Enables/disables holding brake function. This function applies the following profile to the inverter: 0[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 142 6SE6400-5BB00-0BP0 Caution: 1. To activate the motor holding brake, in addition to parameter P1215 = 1, the status signal r0052 bit 12 "motor holding brake active" must be output via a digital output. The user must also select the signal - e.g. in parameter P0731. 2. If [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 143 3.25 DC braking P1230[3] BI: Enable DC braking Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Enables DC braking via a signal applied from an external source. Function remains active whil[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 144 6SE6400-5BB00-0BP0 P1232[3] DC braking current Min: 0 CStat: CUT Datatype: U16 Unit : % Def: 100 P-Group: FUNC Act i ve : Immedia tely QuickComm. : No Max: 250 Defines level of DC current in [%] relative to rated motor current (P 0305). % 100 P1 232 P0305 2 1 [A] r0027 Brake DC ?[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 145 Index: P1233[0] : 1st. Drive data set (DDS) P1233[1] : 2nd. Drive data set (DDS) P1233[2] : 3rd. Drive data set (DDS) Value: P1233 = 0.00 : Not active following OFF1 / OFF3. P1233 = 0.01 - 250.00 : Active for the specified duration. Caution: With the DC braking,[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 146 6SE6400-5BB00-0BP0 3.26 Compound braking P1236[3] Compound braking curr ent Min: 0 CStat: CUT Datatype: U16 Unit : % Def: 0 P-Group: FUNC Act i ve : Immedia tely QuickComm. : No Max: 250 Defines DC level superimposed on AC waveform after exeeding DC-link voltage threshold of compo[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 147 3.27 Dynamic braking P1237 Dynamic braking Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: FUNC Act i ve : Immedia tely QuickComm. : No Max: 5 Dynamic braking absorbs the braking energy. This parameter activates the function "Dynamic braking" [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 148 6SE6400-5BB00-0BP0 t V DC t V D C , C hopper V DC, a ct Chopper ac tiv e t t C hopper , ON C hopper t f 1 = C hopper Hz 2000 1 = t t C hopper , ON t 100 x ⋅ = C hopper V DC , a ct – V D C , C hopper 100 % V ∆ V 0 1 1 0 x Alar m A 0535 D u t y cycle moni tor ing 0 1 P1237 Mai[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 149 Caution: If P1245 increased too much, it may interfere with the drive normal operation. Note: Vdc max controller automatically increases ramp-down times to keep the DC-link voltage (r0026) withi n limits (r1242). Vdc min is activated if DC-link voltage falls bel[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 150 6SE6400-5BB00-0BP0 P1245[3] Switch on lev el kin. buffering Min: 65 CStat: CUT Datatype: U16 Unit : % Def: 76 P-Group: FUNC Act i ve : Immedia tely QuickComm. : No Max: 115 Enter switch-on level for kinetic buffering (KIB) in [%] relative to supply voltage (P0210). P0210 2 100 [% [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 151 P1253[3] Vdc-controll er output limitation Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 10.00 P-Group: FUNC Act i ve : Immedia tely QuickComm. : No Max: 600.00 Limits maximum effect of Vdc max controller. Index: P1253[0] : 1st. Drive data set (DDS) P1253[[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 152 6SE6400-5BB00-0BP0 P1256 = 1: Maintain dclink voltage until mains is returned or drive is tripped undervoltage or pulses disabled when frequency falls below the limit in P1257. P1245 t 0 1 V DC t t f V DC_m i n P1257 Pulse enabled P1256 = 2: This option ramps down the frequency to[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 153 3.29 Control mode P1300[3] Control mode Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: Yes Max: 23 Controls relationship between speed of motor and voltage supplied b y inverter as illustrated in the diagram[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 154 6SE6400-5BB00-0BP0 P1300 = 19 : V/f control with independent voltage setpoint The following table presents an overview of control parameters (V/f) that can be modif y in relationship to P1300 dependencies: ParNo. Level 012356 1 9 2 0 2 2 2 1 2 3 P1300[3] 2 x x x xxxxxxx x P1310[3][...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 155 Vector Control (VC): - P1460: P gain - P1462: I term The following table presents an overview of control parameters (SLVC, VC) that can be modify in relationship to P1300 dependencies: 1) If t he speed c ontr ol ( main s etpoint ) is sel ected a tor que setpoi n[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 156 6SE6400-5BB00-0BP0 3.29.1 V/f control technique P1310[3] Continuous boost Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 50.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 250.0 P1310 causes a voltage boost depending on the output frequency (see diagran). At l [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 157 Dependency: Continous boost P1310 has no effect during vector operation becaus e the inverter calculates continously the optimum operating conditions. Note: - Increasing the boost levels increases motor heating (especially at standstill). - The boost values are [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 158 6SE6400-5BB00-0BP0 P1312[3] Starting boost Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 0.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 250.0 Applies a constant linear offset (in [%] relative to P0305 (rated motor current)) to active V/f curve (either linea[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 159 P1316[3] Boost end frequen cy Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 20.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 100.0 Defines point at which programmed boost reaches 50 % of its value. This value is expressed in [%] relative t[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 160 6SE6400-5BB00-0BP0 P1321[3] Programmable V/f volt. coord. 1 Min: 0.0 CStat: CUT Datatype: Float Unit : V Def: 0.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 3000.0 See P1320 (programmable V/f freq. coord. 1). Index: P1321[0] : 1st. Drive data set (DDS) P1321[1][...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 161 P1333[3] Start frequency for FCC Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 10.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 100.0 Defines the FCC starting frequency as a percent age of the rated motor freq uency (P0310). When FCC is ac[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 162 6SE6400-5BB00-0BP0 3.29.1.1 Slip compensation P1335[3] Slip compensation Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 0.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 600.0 Dynamically adjusts output frequency of inverter so that motor speed is kept constant[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 163 P1336[3] Slip limit Min: 0 CStat: CUT Datatype: U16 Unit : % Def: 250 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 600 Compensation slip limit in [%] relative to r0330 (rated motor slip), which is added to frequenc y setpoint. Index: P1336[0] :[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 164 6SE6400-5BB00-0BP0 3.29.1.3 Imax controller P1340[3] Imax freq. controller prop. gain Min: 0.000 CStat: CUT Datatype: Float Unit : - Def: 0.000 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 0.499 Proportional gain of the I_max frequenc y controller. The Imax contr[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 165 r1343 CO: Imax controller freq. output Min: - Datatype: Float Unit : Hz Def: - P-Group: CONTRO L Max: - Displays effective frequency limitation. Dependency: If I_max controller not in operation, parameter norm ally shows max. frequency P1082. r1344 CO: Imax cont[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 166 6SE6400-5BB00-0BP0 3.29.1.4 Soft starting P1350[3] Voltage soft start Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: No Max: 1 Selecting the soft starting function. With soft starting, the flux in the motor is established wit[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 167 3.29.2 Field-orientated vector control P1400[3] Configuration of speed c ontrol Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 1 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 3 Configuration for speed control. Bitfields: Bit00 Automatic Kp adapti[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 168 6SE6400-5BB00-0BP0 3.29.2.1 Speed controller with/w ithout encoder P1442[3] Filter time for act. speed Min: 0 CStat: CUT Datatype: U16 Unit : ms Def: 4 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 32000 Sets time constant of PT1 filter to smooth actual speed of s[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 169 P1470[3] Gain speed controller (SLVC) Min: 0.0 CStat: CUT Datatype: Float Unit : - Def: 3.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 2000.0 Enters gain of speed controller for sensorless vector control (SLVC). r1438 r 1084 – Kp T n P 1 4 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 170 6SE6400-5BB00-0BP0 r1482 CO: Integral output of n -ctrl. Min: - Datatype: Float Unit : Nm Def: - P-Group: CONTRO L Max: - Displays integral part of speed controller output. 3.29.2.2 Droop P1488[3] Droop input source Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: CONTRO L[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 171 P1489[3] Droop scaling Min: 0.00 CStat: CUT Datatype: Float Unit : - Def: 0.05 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 0.50 Defines amount of droop in per unit at full load in [%]. Index: P1489[0] : 1st. Drive data set (DDS) P1489[1] : 2nd[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 172 6SE6400-5BB00-0BP0 3.29.2.3 Speed controller pre-control P1496[3] Scaling accel. precontrol Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 0.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 400.0 Enters scaling of acceleration in [%]. The response of setpoint ch[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 173 3.29.2.4 Torque control P1500[3] Selection of torque setpo int Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: Yes Max: 77 Selects torque setpoint source. In the table of possible settings below, the main set[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 174 6SE6400-5BB00-0BP0 Caution: Be aware, by changing of parameter P1500 all BICO pa rameters (see table below) are modified. Note: Changing this parameter sets (to default) all settings on item selected (see table). P1500 = xy y = 0 y = 2 y = 4 y = 5 y = 6 y = 7 0.0 755.0 2015.1 2018[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 175 P1501[3] BI: Change to torque c ontrol Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: No Max: 4000:0 Selects command source from which it is possible to change between master (speed control) and slave (t[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 176 6SE6400-5BB00-0BP0 P1503[3] CI: Torque setpoin t Min: 0:0 CStat: T Datatype: U32 Unit : - Def: 0:0 P-Group: CONTRO L Act i ve : first confirm QuickComm.: No Max: 4000:0 Selects source of torque setpoint for torque control. Index: P1503[0] : 1st. Command data set (CDS) P1503[1] : 2[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 177 3.29.2.6 Torque / power limiting P1521[3] CO: Lo w er torque limit Min: -99999.00 CStat: CUT Datatype: Float Unit : Nm Def: -5.13 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 99999.00 Enters fixed value of lower torque limitation. P152 1 max P1[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 178 6SE6400-5BB00-0BP0 r1527 CO: Lower torque limitation Min: - Datatype: Float Unit : Nm Def: - P-Group: CONTRO L Max: - Displays actual lower torque limitation. Details: See parameter r1526. P1530[3] Motoring power limitation Min: 0.00 CStat: CUT Datatype: Float Unit : - Def: 0.12 P[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 179 r1538 CO: Upper torque limit (total) Min: - Datatype: Float Unit : Nm Def: - P-Group: CONTRO L Max: - Displays total upper torque limitation. P1530 M otor ing pow er lim Cur r ent c ontr oll er Speed c ontr ol ler or T or que controll er CO : L o we r tr q . li [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 180 6SE6400-5BB00-0BP0 P1574[3] Dynamic voltage headroom Min: 0 CStat: CUT Datatype: U16 Unit : V Def: 10 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 150 Sets dynamic voltage headroom for vector control. If max. output voltage is reached, the voltage headroom is use[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 181 P1582[3] Smooth time for flux setp oint Min: 4 CStat: CUT Datatype: U16 Unit : ms Def: 15 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 500 Sets time constant of PT1 filter to smooth flux setpoint. Index: P1582[0] : 1st. Drive data set (DDS) P15[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 182 6SE6400-5BB00-0BP0 P1611[3] Acc. torque boost (SLVC) Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 0.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 200.0 Enters the dynamic torque boost for the low frequenc y range for sensorless closed-loop vector control (S[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 183 r1725 CO: Integral limit of Isd ctrl. Min: - Datatype: Float Unit : V Def: - P-Group: CONTRO L Max: - Displays limit of integral output voltage setpoint of Isd current controller. r1728 CO: Decoupling voltage Min: - Datatype: Float Unit : V Def: - P-Group: CONTR[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 184 6SE6400-5BB00-0BP0 SLVC open loop means that the speed controller does not get an y frequency feedback from the obse rver model. . . r 0062 Speed c ontr oll er Pr e- c ontr ol T or que limit at io n Cur r ent c ontr oll er i sq − open/c los ed loop F lux setpoi nt c los ed loop [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 185 P1755[3] Start-freq. motor model (SLVC) Min: 0.1 CStat: CUT Datatype: Float Unit : Hz Def: 5.0 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 250.0 Enter the start frequency of sensorless vector control (SLVC), ther eby SLVC switches over from op[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 186 6SE6400-5BB00-0BP0 P1764[3] Kp of n-adaption (SLVC) Min: 0.0 CStat: CUT Datatype: Float Unit : - Def: 0.2 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 2.5 Enters gain of speed adaptation controller for sensorless vector control. r 1771 ASM ) ˆ i ( I m ψ ⋅ ∆[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 187 P1781[3] Tn of Rs-ada ption Min: 10 CStat: CUT Datatype: U16 Unit : ms Def: 100 P-Group: CONTRO L Act i ve : Immedia tely QuickComm. : No Max: 2000 Enters Rs-adaptation controller integral time. Index: P1781[0] : 1st. Drive data set (DDS) P1781[1] : 2nd. Drive d[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 188 6SE6400-5BB00-0BP0 3.30 Inverter p arameters (Modulator) P1800 Pulse frequency Min: 2 CStat: CUT Datatype: U16 Unit : kHz Def: 4 P-Group: INVERTER Act i ve : Immediately QuickCo mm.: No Max: 16 Sets pulse frequency of power switches in inverter. The frequenc y can be changed in st[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 189 P1825 On-state voltage of IGBT Min: 0.0 CStat: CUT Datatype: Float Unit : V Def: 1.4 P-Group: INVERTER Act i ve : Immediately QuickCo mm.: No Max: 20.0 Corrects on-state voltage of the IGBTs. P1828 Gating unit dead time Min: 0.00 CStat: CUT Datatype: Float Unit [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 190 6SE6400-5BB00-0BP0 Notice: When choosing the setting for measurement, observe the following: 1. "with parameter change" means that the values are actually adopted as Pxxxx parameter settings (see common settings above) and applied to the controller as well as being shown[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 191 r1917[3] Identified stator inductance 2 Min: - Datatype: Float Unit : - Def: - P-Group: MOTOR Max: - Displays identified stator inductance. Index: r1917[0] : U_phase r1917[1] : V_phase r1917[2] : W_phase Details: See P1915 (identified nominal stator inductance) [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 192 6SE6400-5BB00-0BP0 3.32 S peed optimization P1960 Speed control optimisation Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: MOTOR Act i ve : first confirm QuickComm.: No Max: 1 The drive should be set into a vector mode (P1300 = 20 or 21) to car ry out speed controller op[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 193 Caution: Parameter P2000 represents the reference frequency of the above mentioned interfaces. A maximum frequency setpoint of 2*P2000 can be applied via the corresponding interface. Unlike paramete r P1082 (Max. Frequency) this limits the inverter frequenc y in[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 194 6SE6400-5BB00-0BP0 P2002[3] Reference current Min: 0.10 CStat: CT Datatype: Float Unit : A Def: 0.10 P-Group: COMM Acti ve : first confirm QuickComm.: No Max: 10000.00 Full-scale output current used over serial link (corresponds to 4000H). Index: P2002[0] : 1st. Drive data set (DD[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 195 3.34 Communication parameters (USS, CB) P2009[2] USS denormalization Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: COMM Acti ve : first confirm QuickComm.: No Max: 1 Enables denormalization for USS. Possible Settings: 0 Disabled 1 Enabled Index: P2009[[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 196 6SE6400-5BB00-0BP0 P2012[2] USS PZD length Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 2 P-Group: COMM Acti ve : first confirm QuickComm.: No Max: 8 Defines the number of 16-bit words in PZD part of USS telegram. Index: P2012[0] : Serial interface COM link P2012[1] : Serial inte[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 197 P2013[2] USS PKW length Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 127 P-Group: COMM Acti ve : first confirm QuickComm.: No Max: 127 Defines the number of 16-bit words in PKW part of USS telegram. The PKW part consists of the PKE part (1. word), IND part (2. [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 198 6SE6400-5BB00-0BP0 P2014[2] USS telegram off time Min: 0 CStat: CT Datatype: U16 Unit : ms Def: 0 P-Group: COMM Acti ve : Immediately Quick Comm.: No Max: 65535 Defines the telegram failure time for the serial interfaces with USS protocol. The telegram failure time defines the tim[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 199 P2016[8] CI: PZD to BOP link (USS) Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 52:0 P-Group: COMM Acti ve : Immediately Quick Comm.: No Max: 4000:0 Selects signals (process data PZD) to be transmitted to serial interface via USS on BOP link P 2012 P ZD m a pp[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 200 6SE6400-5BB00-0BP0 r2018[8] CO: PZD from COM link (USS) Min: - Datatype: U16 Unit : - Def: - P-Group: COMM Max: - Displays process data received via USS on COM link. . . . r 2037 r 2036 [0] r 2018 [1] [2] [3] [7] ST X LG E AD R Start of text Length Address PKW PZ D BC C P ara m et[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 201 P2019[8] CI: PZD to COM link (USS) Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 52:0 P-Group: COMM Acti ve : Immediately Quick Comm.: No Max: 4000:0 Selects signals (process data PZD) to be transmitted to serial interface via USS on COM link P2012 . . . PZ D 1[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 202 6SE6400-5BB00-0BP0 r2026[2] USS character frame error Min: - Datatype: U16 Unit : - Def: - P-Group: COMM Max: - Displays number of USS character frame errors. Index: r2026[0] : Serial interface COM link r2026[1] : Serial interface BOP link r2027[2] USS overrun error Min: - Datatyp[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 203 r2033 BO: CtrlWrd2 from BOP l ink (USS) Min: - Datatype: U16 Unit : - Def: - P-Group: COMM Max: - Displays control word 2 from BOP link (i.e. word 4 within USS). Bitfields: Bit00 Fixed frequency Bit 0 0 NO 1 YES Bit01 Fixed frequency Bit 1 0 NO 1 YES Bit02 Fixed[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 204 6SE6400-5BB00-0BP0 P2040 CB telegram off time Min: 0 CStat: CT Datatype: U16 Unit : ms Def: 20 P-Group: COMM Acti ve : Immediately Quick Comm.: No Max: 65535 Defines time after which a fault will be generated (F0070) if no telegram is received via the link. The telegramm off time [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 205 P2051[8] CI: PZD to CB Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 52:0 P-Group: COMM Acti ve : Immediately Quick Comm.: No Max: 4000:0 Selects signals (process data PZD) to be transmitted via CB on COM link . . . [0] P2051 [1] [2] [3] [7] r 0021 r 0052 r 005[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 206 6SE6400-5BB00-0BP0 r2090 BO: Control word 1 from CB Min: - Datatype: U16 Unit : - Def: - P-Group: COMM Max: - Displays control word 1 received from communication board (CB). Bitfields: Bit00 ON/OFF1 0 NO 1 YES Bit01 OFF2: Electrical stop 0 YES 1 NO Bit02 OFF3: Fast stop 0 YES 1 NO[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 207 3.35 Fault s, Alarms, Monitoring P2100[3] Alarm number selection Min: 0 CStat: CT Datatype: U16 Unit : - Def: 0 P-Group: ALARMS Act i ve : first confirm Quick Comm.: No Max: 65535 Selects up to 3 faults or warnings for non-default reactions. Index: P2100[0] : Fa[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 208 6SE6400-5BB00-0BP0 P2104[3] BI: 2. Faults ackno w ledgement Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Selects second source of fault acknowledgement. Index: P2104[0] : 1st. Command data set (CDS) P2104[[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 209 r2114[2] Run time counter Min: - Datatype: U16 Unit : - Def: - P-Group: ALARMS Max: - Displays run time counter. It is the total time the drive has been powered up. When power goes value is saved, then restored on powerup. The run time counter r2114 will be calc[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 210 6SE6400-5BB00-0BP0 Example: P2115[0] = 13625 P2115[1] = 2579 P2115[2] = 516 The conversion into binary quantities (U16) results in the following bit pattern: Seconds + minutes: - High byte (MSB) = 00110101 corresponding to the number 53, i.e. s econds 53 - Low byte (LSB) = 0011100[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 211 P2155[3] Threshold frequen cy f_1 Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 30.00 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 650.00 Sets a threshold for comparing actual frequency or frequency to threshold values f_1. This threshold co[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 212 6SE6400-5BB00-0BP0 P2159[3] Threshold frequen cy f_3 Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 30.00 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 650.00 Threshold_3 for comparing frequenc y to thresholds. T cons t . s peed f ilt 0 . .. 1000 [ m s] P 2153. [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 213 P2162[3] Hysteresis fr eq. for overfreq. Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 20.00 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 650.00 Hysteresis frequency for overfrequency-detection as illustrated in the diagram below. 0 1 { M ax[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 214 6SE6400-5BB00-0BP0 P2166[3] Delay time ramp up completed Min: 0 CStat: CUT Datatype: U16 Unit : ms Def: 10 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 10000 Delay time for signal that indicates completion of ramp-up. Index: P2166[0] : 1st. Drive data set (DDS) P216[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 215 r2169 CO: Act. filtered frequen cy 3 Min: - Datatype: Float Unit : Hz Def: - P-Group: ALARMS Max: - Filtered frequency for monitoring behind first-order lowpass filter. - |f_act| > f_1 (see P2155) - |f_act| > f_2 (see P2157) - |f_act| > f_3 (see P2159) [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 216 6SE6400-5BB00-0BP0 P2172[3] Threshold DC-link v oltage Min: 0 CStat: CUT Datatype: U16 Unit : V Def: 800 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 2000 Defines DC link voltage to be compared to actual voltage as illustrated in the diagram below. V dc t 0 1 0 1 P2[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 217 P2174[3] Torque threshold M_thre sh Min: 0.00 CStat: CUT Datatype: Float Unit : Nm Def: 5.13 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 99999.00 Defines torque threshold for comparing actual torque. – + 0 1 { 0 1 SET (Q= 1) Q R ESET (Q= 0) Q &[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 218 6SE6400-5BB00-0BP0 P2179 Current limit for no load ident. Min: 0.0 CStat: CUT Datatype: Float Unit : % Def: 3.0 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 10.0 Threshold current for A0922 (load missing) in [%] relative to P0305 (rated motor curre nt) as illustrate[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 219 P2182[3] Belt threshold frequency 1 Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 5.00 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 650.00 Sets a frequency threshold 1 for comparing actual torque to to rque the envelope for belt failure dete[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 220 6SE6400-5BB00-0BP0 P2184[3] Belt threshold frequency 3 Min: 0.00 CStat: CUT Datatype: Float Unit : Hz Def: 50.00 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 650.00 Sets a threshold F3 for comparing actual torque to torque the envelope for belt failure detection. In[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 221 P2190[3] Lo wer torque threshold 3 Min: 0.0 CStat: CUT Datatype: Float Unit : Nm Def: 0.0 P-Group: ALARMS Act i ve : Immediately QuickCo mm.: No Max: 99999.0 Lower limit threshold value 3 for comparing actual torque. Index: P2190[0] : 1st. Drive data set (DDS) P[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 222 6SE6400-5BB00-0BP0 3.37 T echnology controller (PID controller) P2200[3] BI: Enable PID controller Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Allows user to enable/disable the PID controller. : PID c ont r [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 223 P2201[3] Fixed PID setpoint 1 Min: -200.00 CStat: CUT Datatype: Float Unit : % Def: 0.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 200.00 Defines Fixed PID Setpoint 1 There are three options available for selection of the PID fixed setpoints: 1. [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 224 6SE6400-5BB00-0BP0 Direct selection of PID-FF1 P2201 via DIN 1: P 2 2 1 6 P0701 = 15 or P0701 = 99, P2220 = 722 .0, P2216 = 1 DIN1 r 2224 r 0722 .0 P2220 1 2,3 P2201 0 . . . . 0 . . . . . . . . Dependency: P2200 = 1 required in user access level 2 to enable setpoint source. Note: [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 225 P2206[3] Fixed PID setpoint 6 Min: -200.00 CStat: CUT Datatype: Float Unit : % Def: 50.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 200.00 Defines Fixed PID Setpoint 6 Index: P2206[0] : 1st. Drive data set (DDS) P2206[1] : 2nd. Drive data set (DD[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 226 6SE6400-5BB00-0BP0 P2212[3] Fixed PID setpoint 12 Min: -200.00 CStat: CUT Datatype: Float Unit : % Def: 110.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 200.00 Defines Fixed PID Setpoint 12 Index: P2212[0] : 1st. Drive data set (DDS) P2212[1] : 2nd. Drive data set [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 227 P2218[3] Fixed PID setpoint mode - Bit 2 Min: 1 CStat: CT Datatype: U16 Unit : - Def: 1 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 3 BCD or direct selection Bit 2 for PID setpoint. Possible Settings: 1 Direct selection 2 Direct selection + ON com[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 228 6SE6400-5BB00-0BP0 P2222[3] BI: Fixed PID setp. select Bit 2 Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 0:0 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines command source of fixed PID setpoint selection Bit 2 Index: P2222[0] : 1st. Command data se[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 229 P2227[3] Fixed PID setpoint mode - Bit 5 Min: 1 CStat: CT Datatype: U16 Unit : - Def: 1 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 2 Direct selection / direct selection + ON Bit 5 for PID setpoint. Possible Settings: 1 Direct selection 2 Direct s[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 230 6SE6400-5BB00-0BP0 P2235[3] BI: Enable PID-MOP (UP -cmd) Min: 0:0 CStat: CT Datatype: U32 Unit : - Def: 19:13 P-Group: COMMANDS Act i ve : first confirm QuickComm.: No Max: 4000:0 Defines source of UP command. Index: P2235[0] : 1st. Command data set (CDS) P2235[1] : 2nd. Command d[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 231 r2250 CO: Output setp oint of PID-MOP Min: - Datatype: Float Unit : % Def: - P-Group: TECH Max: - Displays output setpoint of motor potentiometer in [%]. % 100 P2000 f act ⋅ 1 0 1 0 t t t DIN BOP US S CB CO M l i nk 1 0 t P2235 P2236 P0840 r 2250 % 100 P2000 P[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 232 6SE6400-5BB00-0BP0 These structures are selected using parameters P2200 and P22 51 (refer to the following table). P2200 = 0: 0 2) P2251 = 0 1 P2200 = 1: 0 2) P2251 = 0 2 P2200 = 0: 0 1) P2251 = 1 3 P2200 = 1: 0 1) P2251 = 1 4 − − − O N: ac tiv e O F F 1/3: acti ve O N: - O [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 233 P2253[3] CI: PID setpoint Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Defines setpoint source for PID setpoint input. PI D MO P AD C PI D SU M PI D PI D FF US S BOP lin k US S C OM lin k C[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 234 6SE6400-5BB00-0BP0 P2257 Ramp-up time for PID setpoint Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 1.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 650.00 Sets the ramp-up time for the PID setpoint. PID Setpoi nt ( % ) 0 100 % t ( s ) x 2 x 1 P2257 t 12 P2257 [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 235 P2261 PID setpoint filter timeconstant Min: 0.00 CStat: CUT Datatype: Float Unit : s Def: 0.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 60.00 Sets a time constant for smoothing the PID setpoint. Note: 0 = no smoothing r2262 CO: Filtered PID setp[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 236 6SE6400-5BB00-0BP0 P2267 Max. value for PID feedback Min: -200.00 CStat: CUT Datatype: Float Unit : % Def: 100.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 200.00 Sets the upper limit for the value of the feedback signal in [%]. Note: - P2267 = 100 % corresponds to[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 237 P2274 PID derivative time Min: 0.000 CStat: CUT Datatype: Float Unit : s Def: 0.000 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 60.000 Sets PID derivative time. P2274 = 0: The derivative term does not have any effect (it applies a gain of 1). P2280[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 238 6SE6400-5BB00-0BP0 P2292 PID output lower limit Min: -200.00 CStat: CUT Datatype: Float Unit : % Def: 0.00 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 200.00 Sets lower limit for the PID controller output in [%]. Dependency: A negative value allows bipolar operation [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 239 P2354 PID tuning timeout length Min: 60 CStat: CUT Datatype: U16 Unit : s Def: 240 P-Group: TECH Ac ti ve : Immediately Quick Comm.: No Max: 65000 This parameter determines the time that the auto tu ning code will wait before aborting a tuning run if no oscillat[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 240 6SE6400-5BB00-0BP0 P2484[3] No. of shaft turns = 1 Unit Min: 0.01 CStat: CUT Datatype: Float Unit : - Def: 1.00 P-Group: CONTRO L Act i ve : first confirm QuickComm.: No Max: 9999.99 Sets the number of rotations of the motor shaft required to rep resent 1 unit of user selected uni[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 241 3.39 Free function blocks (FFB) P2800 Enable FFBs Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 1 Free function blocks (FFB) are enabled in two steps. 1. Parameter P2800 enables all free function block[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 242 6SE6400-5BB00-0BP0 P2802[14] Activ ate FFBs Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 3 Free function blocks (FFB) are enabled in two steps. 1. Parameter P2800 enables all free function blocks , normally (P2800 = 1) [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 243 P2810[2] BI: AND 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 P2810[0], P2810[1] define inputs of AND 1 element, output is P2811. P2800 P2801 [ 0] A B C & P2810 r2811 AB C 000 010 100[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 244 6SE6400-5BB00-0BP0 P2816[2] BI: OR 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 P2816[0], P2816[1] define inputs of OR 1 element, output is P2817. A B C P2816 r2817 AB C 00 0 01 1 10 1 11 1 1 P2800 P2801 [3[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 245 P2822[2] BI: XOR 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 P2822[0], P2822[1] define inputs of XOR 1 element, output is P2823. A B C P2822 r2823 AB C 00 0 01 1 10 1 11 0 1 = P2800 P280[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 246 6SE6400-5BB00-0BP0 P2828 BI: NOT 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 P2828 defines input of NOT 1 element, output is P2829. P2828 r2829 1 C A AC 01 10 P2800 P2801 [9] In d e x0 Dependency: P2801[9][...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 247 P2834[4] BI: D-FF 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 P2834[0], P2834[1], P2834[2], P2834[3] define inputs of D-FlipFlop 1, outputs are P2 835, P2836. 1 P2834 SET (Q=1) R ESET ( [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 248 6SE6400-5BB00-0BP0 r2838 BO: Q D-FF 2 Min: - Datatype: U16 Unit : - Def: - P-Group: TECH Max: - Displays output of D-FlipFlop 2, inputs are defined in P2837[0], P2837[1], P2837[2], P2837[3] Dependency: P2801[13] is active level for the D-FlipFlop. r2839 BO: NOT-Q D-F F 2 Min: - Da[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 249 r2845 BO: NOT-Q RS-FF 2 Min: - Datatype: U16 Unit : - Def: - P-Group: TECH Max: - Displays Not-output of RS-FlipFlop 2, inputs are defined in P2843[0], P2843[1] Dependency: P2801[15] is active level for the RS-FlipFlop. P2846[2] BI: RS-FF 3 Min: 0:0 CStat: CUT D[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 250 6SE6400-5BB00-0BP0 P2849 BI: Timer 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 0:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Define input signal of timer 1. P2849, P2850, P2851 are the inputs of the timer, outputs are P2852, P 2853. T 0 0 T TT r2 8 5 [...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 251 P2851 Mode timer 1 Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 13 Selects mode of timer 1. P2849, P2850, P2851 are the inputs of the timer, outputs are P2852, P2853. Possible Settings: 0 ON delay (se[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 252 6SE6400-5BB00-0BP0 r2858 BO: Nout timer 2 Min: - Datatype: U16 Unit : - Def: - P-Group: TECH Max: - Displays Not-output of timer 2 P2854, P2855, P2856 are the inputs of the timer, out puts are P2857, P2858. Dependency: P2802[1] is active level for the timer. P2859 BI: Timer 3 Min:[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 253 P2866 Mode timer 4 Min: 0 CStat: CUT Datatype: U16 Unit : - Def: 0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 13 Selects mode of timer 4. P2864, P2865, P2866 are the inputs of the timer, outputs are P2867, P2868. Possible Settings: 0 ON delay (se[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 254 6SE6400-5BB00-0BP0 P2873[2] CI: SUB 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 755:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Define inputs of Subtracter 1, result is in P2874. P2873 r2874 x 1 x 2 200 % - 200 % x1 - x2 P2800 P 2802[ 6] x 1 - x2 >[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 255 P2879[2] CI: MUL 2 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 755:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Define inputs of Multiplier 2, result is in P2880. Index: P2879[0] : Connector input 0 (CI 0) P2879[1] : Connector input 1 [...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 256 6SE6400-5BB00-0BP0 P2885[2] CI: CMP 1 Min: 0:0 CStat: CUT Datatype: U32 Unit : - Def: 755:0 P-Group: TECH Ac ti ve : first confirm QuickComm.: No Max: 4000:0 Defines inputs of Comparator 1, output is P2886. P2885 r2886 x 1 x 2 Out x1 ≥ x2 → Out = 1 x1 < x2 → Out = 0 P2800[...]

Issue 01/06 Parameter Description MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 257 3.40 Inverter p arameters P3900 End of quick commissioning Min: 0 CStat: C Datatype: U16 Unit : - Def: 0 P-Group: QUICK Act i ve: first confirm QuickComm.: Yes Max: 3 Performs calculations necessary for optimized motor operation. After completion of calculation,[...]

Parameter Description Issue 01/06 MICROMASTER 440 Parameter List 258 6SE6400-5BB00-0BP0 P3980 Commissioning command selection Min: 0 CStat: T Datatype: U16 Unit : - Def: 0 P-Group: - Act i ve : first confirm QuickComm.: No Max: 67 Toggles command and setpoint sources between freel y programmable BICO parameters and fixed command/setpoint profiles f[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 259 4 Function Diagrams - 10 - Function diagram 8 7 6 5 4 3 2 1 0010_Symbols.vsd MICROMASTER 440 16.01.2006 V2.1 Symbols in funktion diagr ams ParName [Dim] PNumber.C/D [3] (Default) ParName [Dim] PNum.C/D ParNam e (Default) PNum.C/D [3] PNum [3] ParName [Hz] ParName PN[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 260 6SE6400-5BB00-0BP0 - 1100 - Function diagram 8 7 6 5 4 3 2 1 1100_Overview.vsd Overview MICROMASTER 440 16.01.2006 V2.1 General Overview External inte rfac es Internal setpoint source Technology fun ctio ns Setpoint channel Motor control Modulator USS COM link USS BOP link Encoder Par[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 261 - 1200 - Function diagram 8 7 6 5 4 3 2 1 1200_B ICO_ Overv .v sd Overview MICROMASTER 440 16.01.2006 V2.1 Connection of External and Internal Setpoints CO/BO: Bin.inp.val r0722 r0722 (52:3) BI: Fct. of DOUT 1 P0731.C r0755 [2] CO:ADC scal[4000h] CO/BO: BOP CtrlWd r[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 262 6SE6400-5BB00-0BP0 r0722 - 2000 - Function diagram 8 7 6 5 4 3 2 1 2000_DIN.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 Digital Inputs 24 V T0 & 0 1 PNP/NPN DIN 0 ... 1 P0725 (1) KL5 0 V 24 V Debounce time: DIN 0 ... 3 P0724 (3) 24 V T0 & 0 1 KL6 0 V 24 V Debounce[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 263 - 2100 - Function diagram 8 7 6 5 4 3 2 1 2100_DOUT.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 Digital Outputs (52:3) BI: Fct. of DOUT 1 P0731.C -1 0 1 Invert DOUTs 0 ... 7 P0748 (0) CO/BO: State DOUTs r0747 r0747 NO COM NC Kl.20 Kl.19 Kl.18 (52:7) BI:[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 264 6SE6400-5BB00-0BP0 - 2200 - Function diagram 8 7 6 5 4 3 2 1 2200_ADC.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 Analog Input (ADC) D A Switching bipolar unipolar Digit Warning, signal lost (F0080) ADC after scal.[%] [%] r0754 [2] r0755 [2] CO:ADC scal[4000h] Act.ADC inp[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 265 - 2300 - Function diagr am 8 7 6 5 4 3 2 1 VisioDocu ment External Interfa ces MICROMASTER 440 16.01.20 06 V2.1 Analog Outpu t (DAC) Type of DAC 0 ... 1 P0776 [2 ] (0) A D x(t) Value x1 :DAC sca l. -99999.0 ... 99999.0 [%] P0777 [2] (0 .0) Value y1:DAC scal. 0 ... 2[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 266 6SE6400-5BB00-0BP0 POWER ON is selected, a changeover to the value di splay has taken place with the toggle key and the unit is in the "Operation" status. Raise motor potentio- meter from BOP Seven-segment display Raise key Toggle key Reversin g key ON key OFF key JOG key Pr[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 267 - 2500 - Function diagram 8 7 6 5 4 3 2 1 2500_USSonBOP.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 USS on BOP link, Receiving All parameters: Index = 1 => BOP link PKW PZD 1 [0] r2015 [1] [2] [3] 2 3 4 5 6 7 0 [4] [5] [6] [7] USS baudrate 4 ... 12 P[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 268 6SE6400-5BB00-0BP0 - 2510 - Function diagram 8 7 6 5 4 3 2 1 2510_USSonBOP.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 USS on BOP link, Transmitting PKW PZD 1 2 3 4 5 6 7 0 ADR BCC PZD PKW 0 7654321 Transmit telegram [0] P2016 [2] [3] [4] [1] [5] [6] [7] CO/BO: Act StatWd[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 269 - 2600 - Function diagram 8 7 6 5 4 3 2 1 2600_USSonCOM.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 USS on COM link, Receiving All parameters: Index = 0 => COM link PKW PZD 1 [0] r2018 [1] [2] [3] 2 3 4 5 6 7 0 [4] [5] [6] [7] USS baudrate 4 ... 12 P[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 270 6SE6400-5BB00-0BP0 - 2610 - Function diagram 8 7 6 5 4 3 2 1 2610_USSonCOM.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 USS on COM link, Transmitting PKW PZD 1 2 3 4 5 6 7 0 ADR BCC PZD PKW 7654321 Transmit telegram [0] P2019 [2] [3] [4] [1] [5] [6] [7] CO/BO: Act StatWd1 [...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 271 - 2700 - Function diagram 8 7 6 5 4 3 2 1 2700_CBonCOM.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 CB on COM link, Receiving PKW PZD 1 [0] r2050 [1] [2] [3] 2 3 4 5 6 7 [4] [5] [6] [7] CB tel. off time 0 ... 65535 [ms] P2040 (20) BO: Ctr lWd1 <- CB r[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 272 6SE6400-5BB00-0BP0 - 2710 - Function diagram 8 7 6 5 4 3 2 1 2710_CBonCOM.vsd External Interfaces MICROMASTE R 440 16.01.2006 V2.1 CB on COM link, Transmitting PKW PZD 1 2 3 4 5 6 7 0 Transmit telegram [0] P2051 [2] [3] [4] [1] [5] [6] [7] CO/BO: Act StatWd1 r0052 r0052 r0021 CO: f_ac[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 273 - 3100 - Function diagram 8 7 6 5 4 3 2 1 3100_MOP.vsd Internal Setpoint Source MICROMASTE R 440 16.01.2006 V2.1 Motor Pote ntiometer (MOP) (19:13) BI: Enable MOP(UP) P1035.C (19:14) BI:Enable MOP(DWN) P1036.C 0 1 1 0 1 1 0 0 -1 Max. frequency 0.00 ... 650.00 [Hz] P[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 274 6SE6400-5BB00-0BP0 - 3200 - Function diagram 8 7 6 5 4 3 2 1 3200_FF .vs d Internal Setpoint Source MICROMASTER 440 16.01.2 006 V2.1 Fixed Frequency (FF) bit coded Fixed frequency 4 -650.00 ... 650.00 [Hz] P1004.D (15.00) Fixed frequency 5 -650.00 ... 650.00 [Hz] P1005.D (20.00) Fixed[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 275 - 3210 - Function dia gram 8 7 6 5 4 3 2 1 3210_FF.v sd Internal Setpoint Source MICROMA STER 4 40 16.01.2 006 V2. 1 Fixed F requenc y ( FF) bina ry c oded 0 0 0 1 0 1 0 1 0 1 1 0 1 1 1 1 0 0 0 0 Fixed frequency 5 -650.00 ... 650.00 [Hz ] P1005.D (20.00) Fixed frequ[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 276 6SE6400-5BB00-0BP0 - 3300 - Function diagram 8 7 6 5 4 3 2 1 3300_FP ID. vsd Internal Setpoint Source MICROMASTER 440 16.01.2 006 V2.1 Fixed PID setpoint, bit coded Fixed PID setp. 4 -200.00 ... 200.00 [%] P2204.D (30.00) Fixed PID setp. 5 -200.00 ... 200.00 [%] P2205.D (40.00) Fixed [...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 277 - 3310 - Function dia gram 8 7 6 5 4 3 2 1 3310_FPI D.v sd Internal Setpoint Source MICROMA STER 4 40 16.01.2 006 V2. 1 Fixed PID setpoint, binar y co ded 0 0 0 1 0 1 0 1 0 1 1 0 1 1 1 1 0 0 0 0 Fixed PID setp. 5 -200.00 ... 200.00 [%] P2205.D (40.00) Fixed PID setp[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 278 6SE6400-5BB00-0BP0 - 3400 - Function diagram 8 7 6 5 4 3 2 1 3400_PIDMOP.v sd Internal Setpoint Source MICROMASTER 440 16.01.2006 V2.1 PID Motor Pot entiometer (P ID-MOP ) (19:13) BI: PID-MOP (UP) P2235.C (19:14) BI: PID-MOP (DWN) P2236.C 0 1 1 0 1 1 0 0 -1 Max. frequency 0.00 ... 650[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 279 - 4100 - Function diagram 8 7 6 5 4 3 2 1 4100_S W21. vs d Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Monitoring SwOff freq. f_off 0.00 ... 10.00 [Hz] P2167.D (1.00) |f_act| >= P2167 (f_off) 0 1 & 1 f_act Delay time T_off 0 ... 10000 [ms] P2168.D ([...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 280 6SE6400-5BB00-0BP0 - 4110 - Function diagram 8 7 6 5 4 3 2 1 4110_S W22. vs d Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Monitoring f_act >= f_set Tconst. freq. filt 0 ... 1000 [ms] P2153.D (5) Threshold freq f_1 0.00 ... 650.00 [Hz] P2155.D (30.00) Hyst. freq. f_hys 0.0[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 281 - 4150 - Function diagram 8 7 6 5 4 3 2 1 4150_STW1.vsd Technology Functions MICRO MASTER 440 16.01.2006 V2.1 Control word 1 (r0054) 1) (1:0) BI: 1. OFF2 P0844.C (19:1) BI: 2. OFF2 P0845.C (1:0) BI: Pulse enabling P0852.C (1:0) BI: RFG enable P1140.C (1:0) BI: RFG s[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 282 6SE6400-5BB00-0BP0 - 4160 - Function diagram 8 7 6 5 4 3 2 1 4160_STW2.vsd Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Control word 2 (r0055) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1) (0:0) BI: FF sel. Bit 0 P1020.C (722:3) BI: FF sel. Bit 3 P1023.C (0:0) BI: DDS bit 0 P0820 [...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 283 - 4170 - Function diagram 8 7 6 5 4 3 2 1 4170_ZSW1.vsd Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Status word 1 (r0052) 1) T he sequence control is the internal control (software) for realizing the drive status (r0002) CO/BO: Act StatWd1 r0052 r0052 1 0 [...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 284 6SE6400-5BB00-0BP0 - 4180 - Function diagram 8 7 6 5 4 3 2 1 4180_ZSW2.vsd Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Status word 2 (r0053) 1) T he sequence control is the internal control (software) for realizing the drive status (r0002) CO/BO: Act StatWd2 r0053 r0053 1 0 [...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 285 - 4600 - Function diagram 8 7 6 5 4 3 2 1 4600.vsd Technology Func tions MICROMASTER 440 16.01.2006 V2.1 Vdc Control (max , min) r0070 CO: Act. Vdc [V] r1242 CO: Vd c-max O N lev [V] Int. time Vdc ctrl 0.1 ... 1000.0 [ms] P1251.D (40.0) Diff.time Vdc ctrl 0.0 ... 10[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 286 6SE6400-5BB00-0BP0 - 4800 - Function diagram 8 7 6 5 4 3 2 1 4800_FreeBlocks1.v sd Free Blocks MICROMAST ER 440 16.01.2006 V2.1 AND-, OR- , XOR- and NOT- Elements 3 AND Elements with 2 I nputs P2800 P2801[0] & P2810 Index0 Index1 r2811 P2800 P2801[1] & P2812 Index0 Index1 r281[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 287 - 4810 - Function diagram 8 7 6 5 4 3 2 1 4810_FreeBlocks2.v sd Free Blocks MICROMAST ER 440 16.01.2006 V2.1 FlipFlops 1 P2834 Index0 Index1 Index2 Index3 SET (Q=1) RESET (Q=0) D STORE POWER ON r2835 r2836 Q Q 1 P2837 Index0 Index1 Index2 Index3 SET (Q=1) RESET (Q=0[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 288 6SE6400-5BB00-0BP0 - 4820 - Function diagram 8 7 6 5 4 3 2 1 4820_FreeBlocks3.vsd Free Blocks MICROMASTER 440 16.01.2006 V2.1 Timers T 0 ON Delay 0 T OFF Delay T T ON/OFF Delay Pulse G ernerator r2852 1 r2853 P2849 Index0 Index0 0 1 2 3 P2851(0) Mode P2850 (0.000) 0.000...6000.0 s P28[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 289 - 4830 - Function diagr am 8 7 6 5 4 3 2 1 4830_FreeBlocks 4.vs d Free Bl ocks MICROMASTER 440 16.01.2006 V2.1 Adders, Subtr acter s, Multipliers , Dividers , 2 Adders with 2 Inputs (1 Word) 2 Subtract ers with 2 Inputs (1 W ord) P2869 r2870 x1 x2 Index0 Index1 200 [...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 290 6SE6400-5BB00-0BP0 - 5000 - Function diagram 8 7 6 5 4 3 2 1 5000_Overview.vsd Overview MICROMASTER 440 16.01.2006 V2.1 Setpoint channel and Motor control 0 1 r1078 CO: Tot. freq.setp [Hz] r2294 CO: Act.PID output [%] (0:0) BI: Enab. PID ctrl P2200.C CI: PID setpoint (0:0) P2253.C CI:[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 291 - 5100 - Function diagram 8 7 6 5 4 3 2 1 5100_PID.vsd Setpoint Channel MICROMASTER 440 16.01.2006 V2.1 PID controller Kp Tn x y + + x y PID trim gain fact 0.00 ... 100.00 P2256 (100.00) PID setp.gain fact 0.00 ... 100.00 P2255 (100.00) PID setp. ramp-up 0.00 ... 65[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 292 6SE6400-5BB00-0BP0 No evaluation with PID - 5200 - Function diagram 8 7 6 5 4 3 2 1 5200_AFM.vsd Setpoint channel MICROMASTER 440 16.01.2006 V2.1 Additional Frequency Modifications (AFM) (0:0) BI: Inh. neg. setp P1110.C (722:1) BI: Reverse P1113.C -1 0 1 0 1 r1114 CO:Setp<-dir.ctrl[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 293 PID trim from AFM POWER ON (Freeze y) Stop RFG - 5300 - Function diagram 8 7 6 5 4 3 2 1 5300_RFG.vsd Setpoint Channel MICROMASTER 440 16.01.2006 V2.1 Ramp Function Gener ator P1133 P1132 (1:0) BI: RFG start P1141.C (1:0) BI:RFG enable setp P1142.C r1119 CO:Setp bef[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 294 6SE6400-5BB00-0BP0 PID trim from AFM Frequency output to modulator n/f(max) + control reser ve active - 6100 - Function diagram 8 7 6 5 4 3 2 1 6100_V_f.vsd V/f Control MICROMASTER 440 16.01.2006 V2.1 Overview of V/f Control Imax controller setpoint + − r1343 CO:Imax ctrl Foutp r134[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 295 Setpoint channel **) settable via P1000 *) Access level 4 - 7000 - Function diagram 8 7 6 5 4 3 2 1 7000.vsd Vector Control MICROMAST ER 440 16.01.2006 V2.1 Overv iew of Speed Control without Encoder (SLVC): – Asyc. Mot. 3~ + + 1 4 2 Max. frequency 0.00 ... 650.00[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 296 6SE6400-5BB00-0BP0 Encoder Setpoint channel – Asyc. Mot. 3~ + + 1 4 2 Max. frequency 0.00 ... 650.00 [Hz] P1082.D (50.00) Max. frequency 0.00 ... 650.00 [Hz] P1082.D (50.00) r1170 CO:Setp. after RFG [Hz] Scal acc. prectrl. 0.0 ... 400.0 [%] P1496.D (0.0) Inertia [kg*m^2] 0.00010 ...[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 297 **) The speed integrator doesn't w ork in the range of the observer mode l *) settable via P1500 - 7200 - Function diagram 8 7 6 5 4 3 2 1 7200.vsd Vector Control MICROMAST ER 440 16.01.2006 V2.1 Overv iew of Torque Control without Encoder: 2 CI: Add. trq. setp[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 298 6SE6400-5BB00-0BP0 Encoder **) The speed integrator doesn't w ork in the range of the observer mode l *) settable via P1500 - 7210 - Function diagram 8 7 6 5 4 3 2 1 7210.vsd Vector Control MICROMAST ER 440 16.01.2006 V2.1 Overv iew of Torque Control with Encoder: 2 CI: Add. trq.[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 299 Forward speed Speed precontrol Speed controller output Torque limitation Torque limitation **) changeable in run via DDS Observer model Torque limitation Torque limitation speed from observer model Ramp generator - 7500 - Function diagram 8 7 6 5 4 3 2 1 7500_SLVC.v[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 300 6SE6400-5BB00-0BP0 Forward speed Speed precontrol Speed controller output Torque limitation Torque limitation **) changeable in run via DDS Observer model Torque limitation Torque limitation Speed measurement Ramp generator - 7510 - Function diagram 8 7 6 5 4 3 2 1 7510_VC.vsd Vector [...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 301 Current control Observer model Forward speed **) selectable with P1500 enable Flux setpoint - 7700 - Function diagram 8 7 6 5 4 3 2 1 7700_TC.vsd Vector Control MICROMASTER 440 16.01.2006 V2.1 Torque Controller and Torque Limitation (SLVC) Speed precontrol Speed con[...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 302 6SE6400-5BB00-0BP0 Motor stall protection Current control **) selectable with P1500 act. frequency Flux setpoint - 7710 - Function diagram 8 7 6 5 4 3 2 1 7710_TC.vsd Vector Control MICROMASTER 440 16.01.2006 V2.1 Torque Controller and Torque Limitati on (VC) Power lim itation Speed p[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 303 Current control and stall protection Saturation characteristic P0362 ... P0369 *) Speed control Field weakening controller Efficiency optimization Field weakening characteri stic Act. frequency Current control Vdc measurement - 7800 - Function diagram 8 7 6 5 4 3 2 [...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 304 6SE6400-5BB00-0BP0 only SLVC: speed to speed controller Field weakening control Speed or torque control iq controller id controller Flux setpoint Rotor flux Speed control - 7900 - Function diagram 8 7 6 5 4 3 2 1 7900_MM.vsd Vector Control MICROMASTER 440 16.01.2006 V2.1 Current Contr[...]

Issue 01/06 Function Diagrams MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 305 from sheet from sheet from sheet from sheet from sheet from sheet - 8000 - Funct ion diagram 8 7 6 5 4 3 2 1 8000.vsd Vector Control MICROMASTER 440 16.01. 2006 V2 .1 Analog outputs and dis play va lues x y = f(x) y D A 12 13 AOUT1 D A 26 27 AOUT2 0 ... 20 mA 0 ... [...]

Function Diagrams Issue 01/06 MICROMASTER 440 Parameter List 306 6SE6400-5BB00-0BP0[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 307 5 Fault s and Alarms 5.1 Fault messages In the event of a failure, the inverter switches off and a fault code appears on the display. NOTE To reset the fault code, one of three methods li sted below can be used: 1. Cycle the power to the drive. 2. Press the button o[...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 308 6SE6400-5BB00-0BP0 F0003 Undervoltage STOP II Quit Refer to F0001 Cause - line voltage failed - shock stressing outside the permissible limits. Diagnosis & Remed y Please check the following: - is the line supply voltage within the permissible range? - is the line supply voltage s[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 309 F0015 No motor temperature signal STOP II Quit Refer to F0001 Cause - motor temperature sensor either short-circuited or open-circuit. - if it is identified that a signal has been lost, then the temperature monitoring changes-over to monitoring based on the thermal-[...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 310 6SE6400-5BB00-0BP0 F0023 Output fault STOP II Quit Refer to F0001 Cause - one output phase has not been correctly connected. Diagnosis & Remed y Please check the following: - are the connections at the motor terminal box o.k. ? - are the motor cable connections at the inverter o.k[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 311 F0041 Failure, motor data identification STOP II Quit Refer to F0001 Cause Motor data identification run unsuccessful (refer to fault value r0949): - r0949 = 0: Load missing. - r0949 = 1: Current limit was reached during the identification run. - r0949 = 2: Identifi[...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 312 6SE6400-5BB00-0BP0 F0054 Incorrect I/O module STOP II Quit Refer to F0001 Cause - incorrect I/O module i nserted. - no ID of the I/O module found, no data. Diagnosis & Remed y Please check the following: - check I/O data, if required repeat the operation - the installation of the [...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 313 F0090 Signal loss, encoder STOP II Quit Refer to F0001 Cause - encoder signal between the encoder and inverter is interrupted - excessively large difference between the setpoint (reference) and actual frequenc y Diagnosis & Remed y Please check the following: - [...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 314 6SE6400-5BB00-0BP0 F0452 Load torque fault detected STOP II Quit Refer to F0001 Cause - load conditions at the motor signify a load torque fault (e.g. belt failure) or a mechanical fault Diagnosis & Remed y Please check the following: - no braking, failure or destruction of the me[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 315 5.2 Alarm Messages Alarm messages are stored in para meter r2110 under their code number (e.g. A0503 = 503) and can be read out from there. A0501 Current limit value Cause - the motor power rating does not correspond t o the inverter power rating - motor cables are [...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 316 6SE6400-5BB00-0BP0 A0510 Motor overtemperature A0511 Motor overtemperature Cause - motor is overloaded. - load duty cycle is exceeded. Diagnosis & Remed y Check, independently of the type of temperature m onitoring: - P0604 alarm threshold, motor overtemperature - P0625 motor ambi[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 317 A0590 Alarm, no signals from the speed encoder Cause - no speed encoder signals - inverter has changed-over to encoderless vector control. Diagnosis & Remed y Stop the inverter, and - check the speed encoder, if an encoder is not being used, set P0400 to 0 and s[...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 318 6SE6400-5BB00-0BP0 A0707 CB alarm 8 Cause - CB-(Communications module)-spe cific Diagnosis & Remed y - refer to the CB User Manual A0708 CB alarm 9 Cause - CB-(Communications module)-spe cific Diagnosis & Remed y - refer to the CB User Manual A0709 CB alarm 10 Cause - CB-(Comm[...]

Issue 01/06 Faults and Alarms MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 319 A0920 ADC parameters not correctly set Cause ADC parameters should not be set to identical values, as this would lead to illogical results. - Index 0: Parameter settings for output identical. - Index 1: Parameter settings for input identical. - Index 2: Parameter se[...]

Faults and Alarms Issue 01/06 MICROMASTER 440 Parameter List 320 6SE6400-5BB00-0BP0[...]

Issue 01/06 Abbreviations MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 321 6 Abbreviations AC Alternating current AD Analog digital converter ADC Analog digital converter ADR Address AFM Additional frequency modification AG Automation unit AIN Analog input AOP Advanced operator panel AOUT Analog output ASIC Application-specific integrated circ[...]

Abbreviation s Issue 01/06 MICROMASTER 440 Parameter List 322 6SE6400-5BB00-0BP0 EMC Electro-magnetic compatibility EMF Electromotive force EMI Electro-magnetic interference ESB Equivalent circuit FAQ Frequently asked questions FB Function bloc k FCC Flux current control FCL Fast current limit FF Fixed freqeuncy FFB Free function block FOC Field or[...]

Issue 01/06 Abbreviation s MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 323 RCCB Residual current circuit breaker RCD Residual current device RFG Ramp function generator RFI Radio-frequency interference RPM Revolutions per minute SCL Scaling SDP Status display panel SLVC Sensorless vector control STW Control word STX Start of text SVM Space ve[...]

Abbreviation s Issue 01/06 MICROMASTER 440 Parameter List 324 6SE6400-5BB00-0BP0[...]

MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 325 Suggestions and/or Corrections Suggestions Corrections To Siemens AG Automation & Drives Group SD SPA PM 4 P.O. Box 3269 D-91050 Erlangen Federal Republic of Germany For Publication/Manual: MICROMASTER 440 Parameter List Email: documentation.sd@siemen s.com User Documentation From Name: Orde[...]

MICROMASTER 440 Parameter List 326 6SE6400-5BB00-0BP0[...]

MICROMASTER 440 Parameter List 6SE6400-5BB00-0BP0 327[...]

Siemens AG Automation and Drives Group (A&D) Standard Drives (SD) Division Postfach 3269, D-91050 Erlangen Federal Republic of Germany © Siemens AG, 2001, 2002, 200 3, 2004, 2005 Subject to change without prior noti ce Siemens Aktiengesellschaf t Order No.: 6SE6400-5BB00-0B P0[...]