-
Seite 1
For information on the latest products and peripheral devices, refer to the following Web page. ■ http://www.toshiba.com/taisisd The above URL is subject to change without prior notice. If the URL changes, refer to theToshiba website (http://www.toshiba.com/taisisd). If necessary, download “Advanced User's Guide” from above Toshiba websi[...]
-
Seite 2
2 Installation/Setup Others Operation Introduction T ested T o Comply W ith FCC Standards FOR HOME OR OFFICE USE Product Name : NETWORK CAMERA Model Number(s) : IK-WB01A, IK-WB11A FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to [...]
-
Seite 3
3 Installation/Setup Others Operation Introduction Introduction Thank you for purchasing the IK-WB01A/IK-WB11A Network Camera. Before you start using the camera, read this User's Guide carefully to ensure correct usage. Once you have finished reading this User's Guide, keep it in a convenient place for future reference. The design, specif[...]
-
Seite 4
4 Installation/Setup Others Operation Introduction Accessories Confirm that all of the following accessories have been supplied with the network camera. ● Accessories common to IK-WB01A and IK-WB11A AC adaptor (x1) Power cord (x1) Rear cover (waterproof cover and attachment holder for indoor and outdoor installation) with a tripod screw hole (x1)[...]
-
Seite 5
5 Installation/Setup Others Operation Introduction Table of Contents Introduction ● Introduction ............................................................................................................... 3 ● Table of Contents ................................................................................................... 5 ● IMPORTANT[...]
-
Seite 6
6 Installation/Setup Others Operation Introduction IMPORTANT SAFETY INSTRUCTIONS When using this camera, always follow basic safety precautions to reduce the risk of fire, electric shock, or personal injury. 1 . Read and understand all the instructions. 2 , Keep the User's Guide for future reference. 3 . Heed all warnings. 4 . Follow all the i[...]
-
Seite 7
7 Installation/Setup Others Operation Introduction Precautions for Use About the SD Memory Card(IK-WB11A only) ● There is a limit to the number of rewrites that is possible with the SD memory card. Replacing of the SD memory card when performing periodic maintenance of the camera is recommended. ● The camera supports the following SD memory car[...]
-
Seite 8
8 Installation/Setup Others Operation Introduction Be sure to use only the supplied AC adaptor. Using a different AC adaptor may cause the camera to malfunction, heat up, or catch fire. Before using the AC adaptor, carefully read and observe the Important Safety Instructions (→ page 6) and the notes below. ● Do not allow the connectors on the A[...]
-
Seite 9
9 Installation/Setup Others Operation Introduction Overview of the Network Camera The IK-WB01A/IK-WB11A network camera can deliver video images and sound in real time using the Internet or an intranet. The camera is equipped with Ethernet (RJ-45) 10BASE-T/100BASE-TX and wireless LAN IEEE 802.11b network interfaces. IK-WB11A can be used in various i[...]
-
Seite 10
10 Installation/Setup Others Operation Introduction Features of the Camera ● Supports wireless LAN The camera equips the wireless LAN IEEE 802.11b system. This enables you to connect the camera and your computer without using a LAN cable. ● Built-in pan/tilt mechanism A built-in pan (left/right) and tilt (up/down) mechanism enables you to use t[...]
-
Seite 11
11 Installation/Setup Others Operation Introduction ● High Sensitivity(IK-WB11A) The camera accomplishes highly sensitive night-time monitoring by using a slow-shutter speed (up to 4 seconds), Simple DAY/NIGHT function , and an auto sensitivity boost function. ● Employs ND(Neutral Density)switching mechanism(IK-WB11A) Outdoor an[...]
-
Seite 12
12 Introduction Installation/Setup Operation Others Requirements for Network Camera Monitoring System ○ Administrator's personal computer This camera cannot be used by itself. Be sure to connect the camera to a personal computer and network. This User's Guide refers to a personal computer that has been granted all privileges for configu[...]
-
Seite 13
13 Introduction Installation/Setup Operation Others ○ Appropriate connection devices (hub, router, etc.) and LAN cab l e f o r t he network system environment ・ Not required if you are going to connect the personal computer and network camera directly using a wireless LAN. ・ The type of LAN cable depends on the connection method used. For det[...]
-
Seite 14
14 Introduction Installation/Setup Operation Others Setting up the Network Camera Enviroment (Cont.) Names of Camera Parts(IK-WB01A) Front Side Bottom Rear Lens (Focal range: 35 cm to infinity) Lens cover (Transparent sphere) Reset button (→ page 39) ・ Reset the settings to the defaults by using a thin, pointed object to press the button fo[...]
-
Seite 15
15 Introduction Installation/Setup Operation Others Names of Camera Parts (IK-WB11A) Front Side Bottom Rear Sun visor (→ page 19) (Accessory) Lens (Focal range: 80 cm to infinity) Lens cover (Transparent sphere) Reset button (→ page 39) ・ Reset the settings to the defaults by using a thin, pointed object to press the button for at least 5 sec[...]
-
Seite 16
16 Introduction Installation/Setup Operation Others The IK-WB01A is for indoor use only. The following explains the installation procedure. Set the wall attachment to the wall ・ Attach each of the four corners to the wall using four wood screws . Important ● Securely tighten the screws during installation to ensure not to become loosen. Connect[...]
-
Seite 17
17 Introduction Installation/Setup Operation Others Set the camera to the wall attachment Front view Front view Rear view Rear view Front Rear view Front view ① Place the camera to the wall attachment at the angle shown in the picture. ② Turn the camera counter-clockwise. ・ Make sure that the camera and wall attachment are properly fitting to[...]
-
Seite 18
18 Introduction Installation/Setup Operation Others Some provided parts are required for installing the camera. ● Installing the camera indoors ・ Rear cover ● Installing the camera outdoors ・ Rear cover ・ Sun visor ■ Indoor Installation Install the rear cover to the wall ・ Install each of the four corners to the wall using four wood s[...]
-
Seite 19
19 Introduction Installation/Setup Operation Others Connect the AC adaptor cable and the LAN cable to the camera ・ For details, refer to "Connecting the Power Cord" (→ page 21) . ・ If you are going to use a wireless LAN, you need to connect the AC adaptor cable only. Install the camera to the rear cover ・ Fix the camera to the rea[...]
-
Seite 20
20 Introduction Installation/Setup Operation Others Connect the AC adaptor cable and LAN cable to the camera ・ The procedure is the same as that described in "Indoor Installation" Step 3 on page 19. Attach the camera to the rear cover ・ The procedure is the same as that described in "Indoor Installation" Step 4 on page 19. ?[...]
-
Seite 21
21 Introduction Installation/Setup Operation Others Connect the power cord to the AC adaptor Insert the AC adaptor plug into the camera power terminal Important ● There is not much space around the opening of the power terminal, so make sure that the plug is properly inserted. The camera may not work properly if the plug is not inserted properly.[...]
-
Seite 22
22 Introduction Installation/Setup Operation Others As shown in the figure below, use a wire clamp to fix the plug in place ・ For the wire clamp, use the self-tapping screw supplied with the camera to hold. ・ When the plug is fixed in place, check that it will not become disconnected by a moderate amount of pulling. Turning on the Power The cam[...]
-
Seite 23
23 Introduction Installation/Setup Others Operation ■ About the IP Address To connect to the network, the administrator needs to set the network camera IP address. There are two options to set the IP address. ・ Obtaining an IP address automatically from the DHCP server ・ Entering an IP address manually (→ page 36) ●Obtaining an IP[...]
-
Seite 24
24 Introduction Installation/Setup Others Operation Connecting the Camera and Personal Computer by Network (Cont.) Using LAN Cable The following shows two different network configurations using a LAN cable connection to operate the network camera. ・ Crossover connection ・ Connection via a hub ● Using a crossover cable to establish a connectio[...]
-
Seite 25
25 Introduction Installation/Setup Others Operation Using Wireless LAN The followings show different network configurations using a wireless LAN connection to operate the network camera. ■ When using adhoc method The adhoc method is used for connecting the network camera and a personal computer. Network camera Adhoc method Personal computer IP ad[...]
-
Seite 26
26 Introduction Installation/Setup Others Operation Connecting the Camera and Personal Computer by Network (Cont.) NO TE ● Information may be intercepted if you use a wireless LAN connection. Improve security by using WEP key. (→ page 33) ● Communication using a wireless LAN connection is slower compared to that of a wired connection, therefo[...]
-
Seite 27
27 Introduction Installation/Setup Others Operation About Wireless LAN Connection There are two methods to establish the wireless LAN connection. 1. Cofiguring the wireless network environment for the camera's wireless LAN settings. 2. Cofiguring the camera's wireless LAN settings for the wireless network environment. The default settings[...]
-
Seite 28
28 Introduction Installation/Setup Others Operation Connecting the Camera and Personal Computer by Network (Cont.) 4) Make sure of the reply from the personal computer to the network camera ● Start a command prompt. Type as "ping 192.168.0.30" and press "Enter" key. ● If the "Reply from..." message ap[...]
-
Seite 29
29 Introduction Installation/Setup Others Operation ■ Configuring the camera's wireless LAN settings for the wireless network environment Beforehand, connect the LAN cable (straight cable) to a hub that has the power turned on or connect the LAN cable (crossover cable) to a personal computer that has the power turned on. 1) Plug in the camer[...]
-
Seite 30
30 Introduction Installation/Setup Others Operation 6) Plug in the camera a) Confirm that the settings are the same as the wireless network environment. ● When any settings are different from the wireless network enviromment, set the same values. b) Disconnect the LAN cable from the camera. c) Unplug the camera once and plug it in again. 7) Confi[...]
-
Seite 31
31 Introduction Installation/Setup Others Operation Configuring Settings for Wireless LAN To establish a wireless connection, it is necessary for the administrator to configure the appropriate wireless LAN settings. The administrator also needs to set the IP address. For details on setting the IP address, refer to "About the IP Address" ([...]
-
Seite 32
32 Introduction Installation/Setup Others Operation Configure the communication mode ① Click ▼ for the "COM Mode" setting in the right side of the window. ② Select an item from the pull-down menu. ・ If you are going to connect the network camera to the network via a wireless broadband router or access point (AP), select "infr[...]
-
Seite 33
33 Introduction Installation/Setup Others Operation NO TE ● This setting determines the speed of the network camera communi cating with other devices on the wireless LAN. The IEEE 802.11b standard supports the communication speeds of 1.0, 2.0, 5.5, and 11 Mbps. However, it is recommended to select "auto." Configure the WEP key ① Click[...]
-
Seite 34
34 Introduction Installation/Setup Others Operation The camera search application "Camera Finder" is an application for searching network cameras, that can currently be viewed from the administrator's personal computer or a user's personal computer, and connecting to those cameras. You can use this application by downloading it [...]
-
Seite 35
35 Introduction Installation/Setup Others Operation Click the camera you want to login from the list of cameras ・ The chosen camera name and IP address is displayed in the Netwo rk camera log-in fields. To login as an administrator Click the "Administrator" button. ・ For details on Adminstrator Login procedure, refer to pag[...]
-
Seite 36
36 Introduction Installation/Setup Others Operation ● Entering an IP address manually ・ Enter an IP address manually if you are not using, or do not want to use the DHCP server. ・ If you use a DHCP server, the IP address changes from time to time. Therefore, the IP address you set last time may not be valid next time, and you may not able to [...]
-
Seite 37
37 Introduction Installation/Setup Others Operation Enter the camera name Important ● The camera name is displayed along with images in single-view or multi-view screens. If there are multiple cameras, enter a name that will make it easy to identify what the camera is monitoring. Set "DHCP" to "OFF" ・ The default setting is [...]
-
Seite 38
38 Introduction Installation/Setup Others Operation Click the sav e button ・ The settings are registered. NO TE ● Clicking the reset button restores the previous configuration. ● The network camera has a feature (useful for multi view) that automatically detects, and remember other cameras on the same network. If there are other cameras on th[...]
-
Seite 39
39 Introduction Installation/Setup Others Operation Log-in ID and Password Be sure to change the default login ID and password. You are able to change important information and settings of the camera through the Administrator Login. To have higher security, be sure to change your login ID and the password, and don't forget new login ID and pas[...]
-
Seite 40
40 Introduction Installation/Setup Others Operation Log-in ID and Password (Cont.) In the Admin menu, click the toggle (+) of "Administrator Functions" ・ The sub menus appear. Click "Changing the Password" ・ The settings appear in the right side of the window.[...]
-
Seite 41
41 Introduction Installation/Setup Others Operation Enter the login ID and password in the "Current Login ID", "Current Password", "New Login ID", "New Password", and "New Password (Confirm)" fields. Click the sav e button ・ The new login ID and password are saved in the network camera.[...]
-
Seite 42
42 Introduction Installation/Setup Others Operation Administrator Operation The viewing of images, listening sound and operating cameras are not restricted to the administrator. The administrator can use all the functions. However, it is necessary for the administrator to log in through the "Administrator Login" screen, because an adminis[...]
-
Seite 43
43 Introduction Installation/Setup Operation Others ● Admin Menu Screen Camera name Live button Displays images from the camera in single view. Exit button Closes the settings screen. Do not use X button to close the setting screen. Always use "Exit" button to close the setting screen when you made any se[...]
-
Seite 44
44 Introduction Installation/Setup Operation Others Screen Part Names and Functions (Cont.) ● Single View When you close the Single-View window, close the browser directly by pressing button. Camera name Alarm Notification Displayed when an alarm is detected. LIVE/PLAYBACK LIVE: Displaying live image PLAYBACK: Displaying recorded imag[...]
-
Seite 45
45 Introduction Installation/Setup Operation Others ● Administrator Controller Close button Closes the controller. Camera name 1 shot Captures one image from camera. Back Light button Performs back light compensation. Zoom in button Enlarges camera images. Zoom out button Reduces camera image. LIVE button Displ[...]
-
Seite 46
46 Introduction Installation/Setup Operation Others Screen Part Names and Functions (Cont.) ● Preset controller Preset Available/Unavailable Icon Displays whether the preset is configured. Preset Selection button Specifies preset. Preset name Go button Moves the lens to the preset camera position. Set button Resisters assi[...]
-
Seite 47
47 Introduction Installation/Setup Operation Others ● Record list controller (IK-WB11A) List number Displays List numbers from #1 to #168 (Max.) in 10s. Time and date of recording Play button Plays the images recorded at a time when things are normal. You can control the recorded images by using "control buttons for playing re[...]
-
Seite 48
48 Introduction Installation/Setup Operation Others For more details on the settings, please refer to the Advanced User's Guide at http://www.toshiba.com/taisisd. ■ Camera Settings 1.General Settings IK-WB11A 1280 x 960 800 x 600 640 x 480 320 x 240 160 x 120 HIGH/MIDDLE/LOW HIGH/MIDDLE/LOW Desktop/Wall, Ceiling?[...]
-
Seite 49
49 Introduction Installation/Setup Operation Others 2)Motion Sensor Item Function Sensitivity Size Detection Range Associate to P/T Operation Preset No Resume Function Resume Time IK-WB01A ― ― ― ― ?[...]
-
Seite 50
50 Introduction Installation/Setup Operation Others Setting Items (Cont.) 2)Normal Recording (Only Possible when SD Memory Card Inserted) Item Function Recording Cycle* Timer Association IK-WB01A ― ― ― IK-WB11A ON/OFF 1, 2, 5, 10, 30, 60, [...]
-
Seite 51
51 Introduction Installation/Setup Operation Others ■ Network Settings 1.Network Connection Settings 1)General Settings Item Camera Name Auto Identification of Other Cameras DHCP IP Address Subnet Mask Default Gateway IK-WB01A Enter up to 32 single-byte characters ON/OFF ON/OFF Enter the [...]
-
Seite 52
52 Introduction Installation/Setup Operation Others Setting Items (Cont.) 3.Mail Settings 1)Server Settings Item SMTP Server Name SMTP IP Address POP3 Server Name POP3 IP Address IK-WB01A Enter the server name Enter the IP address Enter the server name Enter the IP address IK-WB11A Enter the server name?[...]
-
Seite 53
53 Introduction Installation/Setup Operation Others 7)Conditions for Sending Mail when Internal Battery Runs Out Of Power Item Send Mail When Internal Battery Runs out Out Of Power Message Body IK-WB01A ON/OFF Enter up to 256 single- byte characters IK-WB11A ON/OFF Enter up to 256 single- byte characters ?[...]
-
Seite 54
54 Introduction Installation/Setup Operation Others 4.Routing Table Settings Item Static Routing Table Settings IK-WB01A Configure the following settings for up to ten entries: destination address, subnet mask, gateway address, and metric IK-WB11A Configure the following settings for up to ten entries: destination address, subnet mask,[...]
-
Seite 55
55 Introduction Installation/Setup Operation Others 2)FTP Server Setup IK-WB11A Enter the server name Enter the IP address Enter the User ID Enter the password Reenter the password 21 PORT/PASV Stay connected/ Re-connect IK-WB01A Enter the server name Enter the IP address Enter the User ID En[...]
-
Seite 56
56 Introduction Installation/Setup Operation Others 2.Filtering Settings Item Filtering by MAC Address MAC Address IK-WB01A ON/OFF Enter up to 20 MAC addresses IK-WB11A ON/OFF Enter up to 20 MAC addresses 3.User Restriction Settings Item User Restrictions Login ID Password Password (Confirm) IK-WB01A ON[...]
-
Seite 57
57 Introduction Installation/Setup Operation Others 2.Setting the Time 1)Time Zone Item Time Zone IK-WB01A GMT-12:00∼GMT+12:00 IK-WB11A GMT-12:00∼GMT+12:00 2)Changing the Time Manually Item Date Time IK-WB01A Select a date from the date boxes Select a time from the time boxes IK-WB11A Se[...]
-
Seite 58
58 Introduction Installation/Setup Operation Others ■ Log Management 1.Forwarding Settings Item Forward Log to Another Server Name of Destination Server IP Address of Destination Server IK-WB01A ON/OFF Enter the server name Enter the IP address IK-WB11A ON/OFF Enter the server name Enter the IP addre[...]
-
Seite 59
59 Introduction Installation/Setup Operation Others Specifications *1: The sound may not be clear depending on the conditions of th e lines. *2: The image output is for checking the image during installation. Images and sounds are not deliverd, and recording function will not work during installation. *3: The ND filter makes possible to monitor eit[...]
-
Seite 60
MEMO[...]
-
Seite 61
61 MEMO[...]
-
Seite 62
TOSHIBA AMERICA INFORMATION SYSTEMS. INC Imaging System Division 9740 Irvine Boulevard, Irvine California 92618-1697 PhoneNumber: (800)288-1354 V2.0[...]
-
Seite 63
63[...]
-
Seite 64
LIMITED W ARRANTY NETWORK CAMERA The Imaging Systems Division of T oshiba America information Systems, Inc. ("ISD") makes the following limited warranties with regard to this NETWORK Camera ("Product"). These limited warranties extend to the Original End-User ("Y ou[r]"). One (1) Y ear Limited Warranty of Labor and Par[...]