Canon SX6000 manual

© 2012 CANON INC. YT1-1451-000 MUL TIMEDIA PROJECT OR WX6000 / SX6000 User Commands Revision 1[...]

WX6000 / SX6000 User Commands - - ii T able of Contents 1. Overview ................................................................................................................. 1 2. Communication S pecifications ................................................................................. 2 Communication Sp ecifications ...................[...]

WX6000 / SX6000 User Commands - - iii DZOOM_RA T ............................................................................................................................ 36 ERR ........................................................................................................................... ................ 37 FINE_GA MMA_R ...........[...]

WX6000 / SX6000 User Commands - 1 - 1. Overview These specifications describe the methods of co ntrolling both the Projecto r WX6000 / SX6000 from the PC over an RS-232C connection or LAN. V irtually all operations possible with the re mote control can be cont rolled from the PC. The following symbols are used in these specifications: Symbol Descri[...]

WX6000 / SX6000 User Commands - 2 - 2. Communication S pecifications Communication S pecifications The projector can be cont rolled via RS-232C or LAN connection. PC - Projector connec tion configuration Item S pecifications Item S pecifications Connecti on system PC and projector connected on a "1:1" basis Connecti on system TCP / IP Con[...]

WX6000 / SX6000 User Commands - 3 - Usable Character Codes Use ASCII codes in the red and blue areas. No distinction is made between double-byte char acters and single-byte charac ters. Do not use double-byte or triple-byte charac ters. They will all be recogniz ed as single-byte characters. Uppercase and lowercase versions of the same alphab etic [...]

WX6000 / SX6000 User Commands - 4 - Communication System (Serial) Item S pecifications Communication system RS-232-C Start-stop synchronization Semi- duplex communication Transmission speed 19.2 Kbps Character length 8 bits / character Stop bit 2 bits Parity No ne Transmission format Variable-length re cords with terminals as delimiters Maximum tra[...]

WX6000 / SX6000 User Commands - 5 - Commands T ransmissions sent from the PC to the projector . T ransmission format △ <Command character strings> △ <Delimiter> <Command character st rings> Character string s consisting of 0 or more alphanumeric characters. <Delimiters> One of CR (0Dh), LF (0Ah), CR+LF (0Dh+0Ah), Null (0[...]

WX6000 / SX6000 User Commands - 6 - Response T ransmissions sent from the Projector to th e PC in response to commands from the PC. T ransmission format <Response character string> <Delimiter> <Response character string > Character strings co nsisting of one or more ASCII characters. The first two characters are always one lowerca[...]

WX6000 / SX6000 User Commands - 7 - Other T ransmission recognition On the receiving side (the Projector), the data that is able to be received within the character interval of T c is held, and the transmission is consid ered received when the delimiter is received. If the character inter val received exceeds the T c or if a delimiter is n ot recei[...]

WX6000 / SX6000 User Commands - 8 - 3. Communication Flow T ransmission sent At the PC, the transmission is se nt within character intervals of T c (character interval timeout). T ransmission received At the Projector , the data that is able to be received withi n the character interval of T c is held, and the transmission is considered received wh[...]

WX6000 / SX6000 User Commands - 9 - 4. Command System[...]

WX6000 / SX6000 User Commands - 10 -[...]

WX6000 / SX6000 User Commands - 1 1 - 5. Command List Item Commands Description 1 6AXADJ 6-axis adjustment ON/OFF 2 6AXR-Y 6-axis correction R-Y hue/saturation settings 3 AMBADJ Ambient light correction adjustment ON/OFF 4 AMBLEVEL Ambient li ght level settings 5 AMBTYPE Ambient light type settings 6 ASELA1 Analog PC-1 audi o terminal selection 7 A[...]

WX6000 / SX6000 User Commands - 12 - Item Commands Description 36 KREP Key repeat 37 LAMP Lamp output setting 38 LAMPCOUNTER Lamp ON time inquiry 39 LMPWRN Lamp warning indication at startup 40 MAIN Side control operation emulation 41 MEMCADJ Memory color adjustment 42 MODE Control mode switch 43 MUTE Mute control 44 NR Noise reduction 45 POWER Thi[...]

WX6000 / SX6000 User Commands - 13 - 6. Details of Commands Descriptions of each comm and are prov ided starting from the next page. The command descriptions have the format s hown below . Alphabetic command name This briefly describes the command functi on. Format This indicates the command format. Environment This defines the environments that su[...]

WX6000 / SX6000 User Commands - 14 - 6AXADJ 6-axis adjustment ON / OFF Format 6AXADJ=<6-axis adjustment parameter : ID> GET □ 6AXADJ / ? △ 6AXADJ <6-axis adjustmen t parameter:ID> ON This sets the 6-axis adjustment to ON. OFF This sets the 6-axis adjustment to OFF . Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X [...]

WX6000 / SX6000 User Commands - 15 - 6AXR-Y 6-axis correction R-Y hu e / saturation settings Format 6AXR=<R hue:Number> ▽ <R saturation:Number> ▽ <R brightness:Number> 6AXG=<G hue:Number> ▽ <G saturation:Number> ▽ <G brightness:Number> 6AXB=<B hue:Number> ▽ <B saturation:Number> ▽ <B br[...]

WX6000 / SX6000 User Commands - 16 - AMBADJ Ambient light correction adjustment ON / OFF Format AMBADJ=<Ambient light correction adjustment parameter:ID> GET □ AMBADJ / ? △ AMBADJ <Ambient light correction adj ustment parameter:ID> ON This sets the ambient light correction adjustment to ON. OFF This sets the ambient light correction[...]

WX6000 / SX6000 User Commands - 17 - AMBLEVEL Ambient light level settings Format AMBLEVEL=<Ambient light level settings parameter:ID> GET □ AMBLEVEL / ? △ AMBLEVEL <Ambient light level settings parameter:ID> WEAK This sets the ambient light level to WEAK. MIDDLE This sets the ambient light level to MIDDLE. STRONG This sets the ambi[...]

WX6000 / SX6000 User Commands - 18 - AMBTYPE Ambient light type settings Format AMBTYPE=<Ambient light type settings parameter:ID> GET □ AMBTYPE / ? △ AMBTYPE <Ambient light type settings parameter: ID> TG This sets the ambient light type to T ung sten. FL This sets the ambient light type to Fluorescent. FL_H This sets the ambient l[...]

WX6000 / SX6000 User Commands - 19 - ASELA1 Analog PC-1 audio termina l selection Format ASELA1=<Analog PC-1 audio terminal selection: ID> GET □ ASELA1 / ? △ ASELA1 <Analog PC-1 Audio terminal selection parame ter: ID> 1 Audio In 1 2 Audio In 2 OFF T urned off Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Resp[...]

WX6000 / SX6000 User Commands - 20 - ASELA2 Analog PC-2 Audio terminal selection Format ASELA2=<Analog PC-2 audio terminal selection: ID> GET □ ASELA2 / ? △ ASELA2 <Analog PC-2 audio terminal selection: ID> 2 Audio In 2 2 Audio In 2 OFF T urned off Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response '&[...]

WX6000 / SX6000 User Commands - 21 - ASELC Component audio terminal sel ection Format ASELC=<Component audio terminal selection parameter: ID> GET □ ASELC / ? △ ASELC <Component audio terminal select ion parameter: ID> 1 Audio In 1 2 Audio In 2 OFF T urned off Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Resp[...]

WX6000 / SX6000 User Commands - 22 - ASELD Digital PC audio terminal selection Format ASELD=<Digital PC audio terminal selection parameter: ID> GET □ ASELD / ? △ ASELD <Digital PC audio terminal selection parameter: ID> 1 Audio In 1 2 Audio In 2 OFF T urned off Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Res[...]

WX6000 / SX6000 User Commands - 23 - ASELH HDMI audio terminal selection Format ASELH=<HDMI audio terminal selection parameter: ID> GET □ ASELH / ? △ ASELH <HDMI audio terminal selection parameter: ID> H HDMI audio 1 Audio In 1 2 Audio In 2 OFF T urned off Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response[...]

WX6000 / SX6000 User Commands - 24 - ASPECT Screen settings Format ASPECT=<Screen setting parameters: ID> GET □ ASPECT / ? △ ASPECT <Screen setting parameters:ID> AUTO Auto 4:3 4:3 16:9 16:9 16:10 16:10 ZOOM Zoom TRUE Real Environment Power Input OFF ON PM Parameter D-RGB A-RGB COMP HDMI None X O X AUTO ○ ○ ○ ○ ○ 4:3 ○ ?[...]

WX6000 / SX6000 User Commands - 25 - Example Setting > ASPECT=16:9 This sets the sc reen size to 16:9. < i:OK Reference > GET ASPECT or ?ASPECT T his retrieves the screen size. < g:ASPECT=TRUE *Commands are indicated by ">", and responses are indicated by "<".[...]

WX6000 / SX6000 User Commands - 26 - AUTOPC Auto PC Format AUTOPC △ Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X X O X X X Response "i:OK" is returned if the control was executed properly . For details on other response s, refer to the "Error List" . Description (1) This executes Auto PC. (2) This command[...]

WX6000 / SX6000 User Commands - 27 - AUTOSETEXE Auto setup Format AUTOSETEXE □ <Auto set parameter:ID> <Auto set parameter:ID> INPUT Automatic signal sensing execution Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response  i:OK” is returned when the automatic processing was completed successfully . For det[...]

WX6000 / SX6000 User Commands - 28 - AV O L Audio volume adjustment Format AVOL=<Audio volume level:Number> GET □ AVOL / ? △ AVOL Setting values for <Audio volu me level:Number> are 0 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . [...]

WX6000 / SX6000 User Commands - 29 - BLANK BLANK function Format BLANK=<BLANK parameter:ID> GET □ BLANK / ? △ BLANK <BLANK parameter:ID> ON BLANK ON OFF BLANK OFF Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ' GET BLANK ' [...]

WX6000 / SX6000 User Commands - 30 - BRI Brightness setting Format BRI=<Brightness setting:Number> GET □ BRI / ? △ BRI Setting values for <Brightness setting: Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For &apos[...]

WX6000 / SX6000 User Commands - 31 - COLOR_TEMP Color temperature setting Format COLOR_TEMP=<Color temperature setting:Number> GET □ COLOR_TEMP / ? △ COLOR_TEMP Setting values for <Color temperat ure setting:Number> are -17 to 21. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is retur[...]

WX6000 / SX6000 User Commands - 32 - COMVER User command version inquir y Format GET □ COMVER / ? △ COMVER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns the user command version as g:COMVER="<User command version:Character string>" For details on other response s, refer to the "Error List[...]

WX6000 / SX6000 User Commands - 33 - CONT Contrast setting Format CONT=<Contrast setting:Number> GET □ CONT / ? △ CONT Setting values for <Contrast setting:Number > are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ' [...]

WX6000 / SX6000 User Commands - 34 - DGAMMA Dynamic gamma Format DGAMMA=<Dynamic gamma setting parameter:ID> GET □ DGAMMA / ? △ DGAMMA <Dynamic gamma setting parameter:ID> OFF Off WEAK W eak MIDDLE Middle STRONG Strong Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the p[...]

WX6000 / SX6000 User Commands - 35 - DZOOM_POS DZOOM position setting Format DZOOM_POS=<DZOOM position X:Number>,<DZOOM position Y:Number> GET □ DZOOM_POS / ? △ DZOOM_POS <DZOOM p osition X / Y :Number> is a signed integer indica ting the central posi tion of the enlarge d input image. Environment Power Input OFF ON PM D-RGB A[...]

WX6000 / SX6000 User Commands - 36 - DZOOM_RA T DZOOM ratio setting Format DZOOM_RAT=<DZOOM ratio parameter:ID> GET □ DZOOM_RAT / ? △ DZOOM_RAT <DZOOM ratio parameter:ID> 1 same size (DZOOM disabled) 1.5 1.5x 2 2x 3 3x 4 4x 5 5x 6 6x 8 8x 10 10x 12 12x Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X O O O O X Resp[...]

WX6000 / SX6000 User Commands - 37 - ERR Error information inquiry Format GET □ ERR / ? △ ERR Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns the current erro r information as 'g:ERR=<ErrorID:Character string>' For details on other response s, refer to the "Error List" . <ErrorID:Ch[...]

WX6000 / SX6000 User Commands - 38 - FINE_GAMMA_R Fine gamma (R) adjustment Format FINE_GAMMA_R=<Fine gamma (R) adjustment point 1 adjustment value:Number>, <Fine gamma (R) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (R) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_R / ? △ FINE_GAMMA_R A[...]

WX6000 / SX6000 User Commands - 39 - FINE_GAMMA_G Fine gamma (G) adjustment Format FINE_GAMMA_G=<Fine gamma (G) adjustment point 1 adjustment value:Number>, <Fine gamma (G) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (G) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_G / ? △ FINE_GAMMA_G A[...]

WX6000 / SX6000 User Commands - 40 - FINE_GAMMA_B Fine gamma (B) adjustment Format FINE_GAMMA_B=<Fine gamma (B) adjustment point 1 adjustment value:Number>, <Fine gamma (B) adjustment point 2 adjustment value:Number>, ・・・ ,<Fine gamma (B) adjustment point n adjustment value:Number> GET □ FINE_GAMMA_B / ? △ FINE_GAMMA_B A[...]

WX6000 / SX6000 User Commands - 41 - FL TW RN Filter warning indication at startup Format FLTWRN=<Filter warning parameter: ID> GET □ FLTWRN / ? △ FLTWRN <Filter warning parameter: ID> OFF T urned off ON T urned on Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned when setting[...]

WX6000 / SX6000 User Commands - 42 - FREEZE Freeze status Format FREEZE=<FREEZE parameter:ID> GET □ FREEZE / ? △ FREEZE <FREEZE parameter:ID> ON Image now frozen OFF Image now not frozen Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X O O O O X Response "i:OK" is returned if the parameter was set properl[...]

WX6000 / SX6000 User Commands - 43 - GAMMA Gamma adjustment Format GAMMA=<Gamma adjustment:Number> GET □ GAMMA / ? △ GAMMA Setting values for <Gamma adjustment: Number > are -10 to 10. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For &a[...]

WX6000 / SX6000 User Commands - 44 - HDMI_IN HDMI input setting Format HDMI_IN=<HDMI input setting parameter:ID> GET □ HDMI_IN / ? △ HDMI_IN <HDMI input setting parameter:ID> AUTO Select this when connecting t o an A V equipment. Image processing and menu displays are adjusted r espective to the connected video equipment. PC Select [...]

WX6000 / SX6000 User Commands - 45 - HDMI_OVSCAN HDMI overscan setting Format HDMI_OVSCAN=<HDMI overscan setting parameter:ID> GET □ HDMI_OVSCAN / ? △ HDMI_OVSCAN <HDMI overscan setting parameter:ID> OFF T urns overscan to OFF ON T urns overscan to ON Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - - - O O Respo[...]

WX6000 / SX6000 User Commands - 46 - HUE Hue setting Format HUE=<Hue setting value:Number> GET □ HUE / ? △ HUE Setting values for <Hue setting value:Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For ' GET HUE [...]

WX6000 / SX6000 User Commands - 47 - IMAGE Image mode setting Format IMAGE=<Image mode setting parameter:ID> GET □ IMAGE / ? △ IMAGE <Image mode setting parameter:ID> ST ANDARD Standard PRESENT A TION Presentation VIVID_PHOTO V ivid photo PHOTO_SRGB Photo / sRGB DCM_SIM DICOM Sim* DYNAMIC Dynamic VIDEO V ideo CINEMA Cinema USER_1 Us[...]

WX6000 / SX6000 User Commands - 48 - Setting Commands related to the settings Dynamic gamma FINE_GAMMA_R ∼ B Memory color adjustment MEMCADJ RGB gain / offset adjustment RGBGAIN / RGBOFFSET Lamp mode LAMP 6-axis adjustment 6AXADJ 6-axis color correction 6AXR ∼ Y (5) The current image quality can be acquired using the applicable GET c ommand. (&[...]

WX6000 / SX6000 User Commands - 49 - IMAGEFLIP Flip display Format IMAGEFLIP=<Image flip setting parameters:ID> GET □ IMAGEFLIP / ? △ IMAGEFLIP <Image flip setting parameters:ID> NONE None CEILING Ceiling REAR Rear projection REAR_CEILING Rear proj ection with ceiling Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O [...]

WX6000 / SX6000 User Commands - 50 - INPUT Input selection Format INPUT=<Input selection parameters:ID> GET □ INPUT / ? △ INPUT <Input selection parameters:ID> D-RGB Digital PC A-RGB1 Analog PC-1 A-RGB2 Analog PC-2 COMP Component HDMI HDMI Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK"[...]

WX6000 / SX6000 User Commands - 51 - KREP Key repeat Format KREP=<Key repeat parameter: ID> GET □ KREP / ? △ KREP <Key repeat paramet er: ID> OFF T urned off ON T urned on Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned when Key repeat parameter was completed successfully . [...]

WX6000 / SX6000 User Commands - 52 - LAMP Lamp output setting Format LAMP=<Lamp output setting parameters:ID> GET □ LAMP / ? △ LAMP <Lamp output setting parameters:ID> NORMAL Normal SILENT Silent cooling Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was se[...]

WX6000 / SX6000 User Commands - 53 - LAMPCOUNTER Lamp ON time inquiry Format GET □ LAMPCOUNTER / ? △ LAMPCOUNTER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Returns current lamp on time as ' g:LAMPCOUNTER="<Lamp ON time:Character string>" ' For details on other response s, refer to the &qu[...]

WX6000 / SX6000 User Commands - 54 - LMPWRN Lamp warning indication at startup Format LMPWRN=<Lamp warning parameter: ID> GET □ LMPWRN / ? △ LMPWRN <Lamp warning paramet er: ID> OFF T urned off ON T urned on Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned when setting of lam[...]

WX6000 / SX6000 User Commands - 55 - MAIN Side control operation emulation Format MAIN □ <Side control emulation button parameters:ID> <Side control emulation button parameters:ID> POWER POWER butto n POWER_OFF POWER bu tton pressed twice MENU MENU LENS LENS INPUT INPUT UP UP UP+REP Hold down the UP button *-REP Release the button DOW[...]

WX6000 / SX6000 User Commands - 56 - MEMCADJ Memory color adjustment Format MEMCADJ=<Memory color adjustment parameter:ID> GET □ MEMCADJ / ? △ MEMCADJ <Memory color adjustment parameter:ID> OFF No adjustment MEM_L Memory color adj ustment - light MEM_M Memory color adjustment - medium MEM_H Memory color adjustment - heavy Environmen[...]

WX6000 / SX6000 User Commands - 57 - MODE Control mode switch Format REMOTE LOCAL GET □ MODE / ? △ MODE Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response "i:OK" is always returned with the cont rol mode switch setting. For ' GET MODE ' or ' ?MODE ', current co ntrol mode is returned as &apos[...]

WX6000 / SX6000 User Commands - 58 - MUTE Mute control Format MUTE=<Mute control parameter: ID> GET □ MUTE / ? △ MUTE <Mute control para meter: ID> ON Disables the audio / beep sound. OFF Enables the audio / beep sound. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the [...]

WX6000 / SX6000 User Commands - 59 - NR Noise reduction Format NR=<Noise reduction setting parameter:ID> GET □ NR / ? △ NR <Noise reduction setting pa rameter:ID> OFF Off WEAK W eak MIDDLE Middle STRONG Strong Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X X X O O O Response "i:OK" is returned if noise [...]

WX6000 / SX6000 User Commands - 60 - POWER This controls the power supply Format POWER □ <Parameter:ID> GET □ POWER / ? △ POWER <Parameter:ID> ON Power ON OFF Power OFF Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response "i:OK" is returned if the parameter was set properly . For ' GET POWER &ap[...]

WX6000 / SX6000 User Commands - 61 - PRODCODE Product information inquiry Format GET □ PRODCODE / ? △ PRODCODE Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response Product name is returned as g:PRODCODE="<Product name:Character string>" For details on other response s, refer to the "Error List" . &[...]

WX6000 / SX6000 User Commands - 62 - RC Remote control operation emu late Format RC □ <Remote control emulation button parameters:ID> <Remote control emulatio n button parameters:ID> POWER POWER butto n POWER_OFF POWER bu tton pressed twice MENU MENU E X I T E X I T INPUT INPUT D P C D I G I T A L A P C 1 A N A L O G P C 1 A P C 2 A N[...]

WX6000 / SX6000 User Commands - 63 - * After setting the status of the button to be pressed down, send a command from t he PC to release the pressed status after predetermined time. . * Although emulation parameters for both values and func tion are av ailable for the common key for 1/DZOOM+, 3/VOL+, 4/DZOOM-, 6/VOL- and 9/MUTE, the re is no differ[...]

WX6000 / SX6000 User Commands - 64 - RGBGAIN RGB gain adjustment Format RGBGAIN=<R gain setting:Number> ▽ <G gain setting:Number> ▽ <B gain setting:Number> GET □ RGBGAIN / ? △ RGBGAIN Setting values for <R/G/B gain setting:Number> are -60 to 60. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Res[...]

WX6000 / SX6000 User Commands - 65 - RGBOFFSET RGB offset adjustment Format RGBOFFSET=<R offset setting:Number> ▽ <G offset setting:Number> ▽ <B offset setting:Number> GET □ RGBOFFSET / ? △ RGBOFFSET Setting values for <R/G/B offset setting :Number> are -60 to 60. Environment Power Input OFF ON PM D-RGB A-RGB COMP HD[...]

WX6000 / SX6000 User Commands - 66 - ROMVER ROM version inquiry Format GET □ ROMVER / ? △ ROMVER Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response ROM version of the firmwa re is returned as g:ROMVER="<ROM version:Character string>" For details on other response s, refer to the "Error List" . &l[...]

WX6000 / SX6000 User Commands - 67 - SA T Color saturati on setting Format RGBGAIN=<R gain setting:Number> ▽ <G gain setting:Number> ▽ <B gain setting:Number> GET □ RGBGAIN / ? △ RGBGAIN Setting values for <Color saturation setting value:Number> are -20 to 20. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI N[...]

WX6000 / SX6000 User Commands - 68 - SA VEIMGPRO F Create, save, delete user memory / Create user memory s tatus Format SAVEIMGPROF=<User memory save to parameter:ID> <User memory save to parameter:ID> USER_1 Save to User 1 USER_2 Save to User 2 USER_3 Save to User 3 USER_4 Save to User 4 USER_5 Save to User 5 DEL_ALL Delete all User me[...]

WX6000 / SX6000 User Commands - 69 - SCRNASPECT Screen aspect setting Format SCRNASPECT=<Screen aspect setting parameter:ID> GET □ SCRNASPECT / ? △ SCRNASPECT <Screen aspect setting parameter:ID> 16:10 16:10 16:9 16:9 display 4:3 4:3 display 16:10_DIS 16:10 digi tal image shift *Not available with WX6000 16:9_DIS 16:9 digital imag e[...]

WX6000 / SX6000 User Commands - 70 - SHARP Sharpness setting Format SHARP=<Sharpness setting:Number> GET □ SHARP / ? △ SHARP Setting values for <Shar pness setting:Number> are -10 to 10. Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response "i:OK" is returned if the parameter was set properly . For [...]

WX6000 / SX6000 User Commands - 71 - SIGNAL_INFO Input signal information inquiry Format GET □ SIGNAL_INFO / ? △ SIGNAL_INFO Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response Current input si gnal information is returned as ' g:SIGNAL_INFO="<Input signal information:Character string>" ' For [...]

WX6000 / SX6000 User Commands - 72 - SIGNALST A TUS Signal status inquiry Format GET □ SIGNALSTATUS / ? △ SIGNALSTATUS Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None X O X - Response Current image sign al input status is retur ned as 'g:SIGNALSTATUS=<Signal status:ID>' For details on other response s, refer to the [...]

WX6000 / SX6000 User Commands - 73 - TEMP T emperature sensor value inquiry Format GET □ TEMP / ? △ TEMP Environment Power Input OFF ON PM D-RGB A-RGB COMP HDMI None - - Response For ' GET TEMP ' or ' ?TEMP ', temperature sensor value is returned as ' TEMP=<Number of sensors>,<Sensor 1 value>,…,<Sensor [...]

WX6000 / SX6000 User Commands - 74 - TPTN T est pa ttern Format TPTN=<Test pattern parameter: ID> GET □ TPTN / ? △ TPTN < T est pattern parameter: ID> OFF T urned off CB1 Color bar SSH1 Stair step H No.1 SSH2 Stair step H No.2 SSH3 Stair step H No.3 SSV1 Stair step V No.1 SSV2 Stair step V No.2 SSV3 Stair step V No.3 RTF1 Raster 100[...]

WX6000 / SX6000 User Commands - 75 - Reference > GET TPTN or ?TPTN GET TPTN or ?TPTN T est pa ttern is acquired. < g:TPTN=OFF *Commands are indicated by ">", and responses are indicated by "<".[...]

WX6000 / SX6000 User Commands - 76 - 7. Error List Item Code TYPE Error character s trings Error Remedy 1 0001 e BAD_SEQUENCE Communication sequence err or Wait until a response is receiv ed before sending the next command. 2 0002 e INVALID_COMMAND Invalid (undefined) command. Send a va lid command. 3 0004 e INVALID_FORMAT Invalid command format. S[...]

WX6000 / SX6000 User Commands - 77 - Item Code TYPE Error character s trings Error Remedy 201F e INVALID_SIGNAL Cannot execute command with current input signal. Change the input signal. 17 0801 e INVALID_VALUE Numerical parameters are invalid or outside the specified range. Set the parameters in the correct range. 18 1002 e NO_LOGO_CAPTURED Cannot[...]

WX6000 / SX6000 User Commands - 78 - 8. Error Processing YES YES YES YES YES YES YES YES YES YES YES YES YES E rror j u d gmen t ST ART Invalid command format? "INV ALID_FORMA T" Command executable w hile power mode is OFF? Power mode is "OFF "? "NOT_POWER_SUPPLIED" Internal processin g in pro g ress? "BUSY" [...]

WX6000 / SX6000 User Commands - 79 - YES YES YES YES NO YES YES Incorrect inpu t source? "INV ALID_SOURCE ( ** ) " Limitations in in p ut source? Re q uires in p ut si g nal? No in p ut si g nal? "NO _ SIGNAL" Numerical paramete r outside the speci fied ran g e? "INV AL ID _ VA L U E " User command is ex ecutable FINIS[...]