Dodge 2004 Ram 2500 manual

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 1 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ...................................[...]

[...]

INTRODUCTION CONTENTS m Introduction ........................... 4 m A Message From DaimlerChrysler Corporation . . . 4 m How T o Use This Manual .................. 5 m W arnings And Cautions ................... 5 m V an Conversions/Campers ................. 6 m V ehicle Identification Number ............... 6 m V ehicle Modifications / Alterations[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

Almost 100% of the heavy duty trucks in the United States are diesel power ed because of the fuel economy , rugged durability , and high torque which permits pulling heavy loads. Cummins engines power well over half of these trucks. Now this same technology and pr oven performance is yours in your new Dodge Ram truck equipped with the Cummins 5.9 l[...]

V AN CONVERSIONS/CAMPERS The Manufacturer’s W arranty does not apply to body modifications or special equipment installed by van conversion/camper manufacturers/ body builders. Such equipment includes video monitors, VCRs, heaters, stoves, refrigerators, etc. For warranty coverage and service on these items, contact the applicable manufac- turer [...]

NOTE: It is illegal to remove the VIN plate. VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 7 1[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 1 ▫ Key-In-Ignition Reminder ................ 1 1 ▫ Sentry Key — If Equipped ................ 1 1 m Ignition And Steering Lock ................. 1 4 ▫ Manual T ransmissions ................... 1 4 ▫ Automatic T ransmissions .............[...]

m Security Alarm System — If Equipped ......... 2 9 ▫ Rearming Of The System ................. 2 9 ▫ T o Set The Alarm ...................... 2 9 ▫ T o Disarm The System ................... 3 0 m W indows ............................. 3 1 ▫ Power W indows—If Equipped ............. 3 1 ▫ Sliding Rear W indow—If Equipped ......... 3 2[...]

A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to or der duplicate keys from your dealer or a locksmith. If you r eceived your keys without the bag, ask your dealer to giv[...]

The 9 Security Light 9 , located in the instrument cluster , will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not r eceive a valid signal from the ignition key , the 9 Security Light 9 will flash continuously to signal that the vehicle has been immobilized. If the 9 Secur[...]

Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. T urn the ignition back to the OFF position and remove the first key . 2. Insert the second[...]

IGNITION AND STEERING LOCK Manual T ransmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your vehicle. It may be dif ficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until i[...]

Automatic T ransmissions In the LOCK position, the steering and ignition systems are locked to pr ovide antitheft protection for your ve- hicle. It may be difficult to turn the key fr om the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily . The key can be inserted or withd[...]

DOOR KEY The same key used to start the vehicle is also used to unlock the doors. T o unlock the vehicle doors, insert the key into the lock and turn. T o lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle wit[...]

Power Door Locks — If Equipped NOTE: V ehicles equipped with remote keyless entry do not have a passenger side door lock cylinder . V ehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pr essing the LOCK or UNLOCK buttons on the Remote Keyless E[...]

As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking — If Equipped V ehicles with security will have a feature called 9 Central Locking 9 . When the key is placed in the door cylinder and turned to the 9 Unlock[...]

2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming pr ocedure). 3. Place the key into the ignition. 4. W ithin 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. W ithin 30 seconds, press the drive[...]

Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedur e: Customer Programming sequence to disable or enable: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confu[...]

Child Protection Door Lock T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, th[...]

W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. NOTE: For emergency exit with the s[...]

T o unlock the doors: Press and r elease the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programmed [...]

T o lock the doors: Press and r elease the LOCK button on the transmitter to lock all doors. If the ignition is OFF , when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped fr om the assembly plants activated. If desired this featur e can be disabled by using the followi[...]

V ehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desir ed, this feature can be disabled by using the following pr ocedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedur e). 3[...]

automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will func- tion normally . Panic mode will not disarm the security system on vehicles so equipped. Programming Additional T ransmitters V ehicles with the keyless entry option will be shipped f[...]

9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. W ithin 4 seconds of hearing the chime, press and release any button on the fob being pr ogrammed. 1 1. A single chime will be hear d. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 1 1 for a total of 4 fobs. 13. T urn the ignitio[...]

2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios. T ransmitter Battery Service The recommended r eplacement battery is a 3V lithium 2016 cell. This transmitter requir es two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit bo[...]

SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly . For an addi- tional 15 minutes only the h[...]

T o Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also [...]

WINDOWS Power Windows—If Equipped The control on the left fr ont door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of Quad Cab models. The windows will operate only when the ignition swit[...]

Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, r elease, and the window will go down automatically . W indow Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. T o disable t[...]

WIND BUFFETING W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buf feting occurs with the rear windows open, open the fr ont and rear[...]

Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown fr om the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belte[...]

W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or[...]

2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.?[...]

4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. W ARNING! • A lap belt worn too high can increase[...]

6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , ch[...]

2. T o reattach the seat belt to the fr ont center seat, pull the black buckle latch plate forward fr om the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage. W ARNING! • If the black latch and black buckle are not prop- erly connected when the s[...]

W ARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly . Inserting Latch Plate In Use Position 40 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE[...]

Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located on the upper belt guide, and then move it up or down to the position that serves you best. As a guide, if you are shorter than average, you will pre[...]

2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How T o Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract[...]

NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the airbag control module. Like the airbags, the pretensioners ar e single use items. After a collision that is severe enough to deploy the airbags and preten[...]

3. W ithin 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least thr ee times within 10 seconds, ending with the seat belt buckled. 4. T urn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced W arning System (BeltAlert) can be reacti- [...]

W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver And Right Front Passenger Supplemental Restraint Syste[...]

W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not mount any aftermarket equipment[...]

• Infants in rear facing child r estraints must NEVER ride in the front seat of a vehicle with a passenger fr ont airbag unless the airbag is turned off (Standar d Cab V ehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section. • If your vehicle does not h[...]

Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Crash Sensor • Interconnecting W iring • Knee Impact Bolsters • Passenger Side Frontal Airbag ON/OFF Switch (Stan- dard Cab V e[...]

• The airbag control module also monitors the r eadiness of the electronic parts of the system whenever the ignition switch is in the ST AR T or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column. If the key is in the 9 Off 9 position, in the ACC position or[...]

• When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes yo[...]

because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no r ear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able[...]

T o T urn On the Passenger Airbag (Standard Cab V e- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key fr om the switch. This will turn on the passenger airbag. The “Off” light near the switch will be off when the ignition switch is turned to the ON position.[...]

irritation, move to fresh air . If the irritation continues, see your doctor . If these particles settle on your clothing, follow the garment manufacturer’s instr uc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to prot[...]

bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window . The airbag inflates in about 30 milliseconds (about one-quarter of the time it takes to blink your eyes) with en[...]

Airbag Light Y ou will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: • The airbag light does not come on or flickers during the 6 to 8 seconds when the ignition switch is [...]

W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper re[...]

unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh mor e than 20 lbs (9 kg) and who are older than one year can ride forwar d-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing dir ection are for children w[...]

Here are some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. W e also recommend that you make sure that you can install the child restraint in the vehicle where you will use it befor e you buy it. • The restrain[...]

• In the rear seat, you may have tr ouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the rele[...]

outboard positions and also featur e tether strap anchor- ages, which must be used, located behind the seatback (refer to Child Restraint T ether Anchor later in this section). Identification dots are located above the standar d cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the fr ont seat of a [...]

Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufactur ers will provide add-on tether strap kits for some of their older produc[...]

Installing the Child Restraint System W ARNING! Do not install child restraint systems equipped with LA TCH attachments in the center position of a Quad Cab model rear seat. The LA TCH anchorages in this seat are designed for the two outboard seating posi- tions only . A child may be placed in the rear center seating position of a Quad Cab model us[...]

W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Child Restraint T ether Anchor Child restraints having tether straps and hooks for[...]

T ether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor dir ectly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in [...]

Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the r ear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly impr oved by raising the seat cushion to the “up” position. Remove t[...]

Multiple Child Restraints 66 THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE[...]

Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be lo[...]

• Check the coolant and oil levels frequently . • V ary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins Diesel engine, engine run-in is enhanced by loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 miles (10[...]

Lock Y our V ehicle Always remove the keys fr om the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. T ry to park your vehicle in a well-lighted area and never invite theft by leaving ar - ticles of value exposed. Exhaust Gas W ARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic[...]

Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor , torn webbing, etc.) o[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors ............................... 7 5 ▫ Inside Mirror ......................... 7 5 ▫ Automatic Dimming Mirror— If Equipped .... 7 6 ▫ Outside Mirrors ....................... 7 6 ▫ Exterior Mirrors Folding Featur e ........... 7 7 ▫ Electronic Power Mirr ors — If Equipped .[...]

▫ Adjustable Head Restraints ............... 9 3 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped ............... 9 4 ▫ Power Seats — If Equipped ............... 9 5 ▫ Heated Seats — If Equipped .............. 9 6 m T o Open And Close The Hood .............. 9 7 m Lights ................................ 9 9 ▫ Interior Lights [...]

▫ T o Set At A Desir ed Speed ............... 1 1 0 ▫ T o Deactivate ........................ 1 1 0 ▫ T o Resume Speed ..................... 1 1 0 ▫ T o V ary The Speed Setting ............... 1 1 1 ▫ T o Accelerate For Passing ............... 1 1 1 m Overhead Console— If Equipped ........... 1 1 2 ▫ Courtesy/Reading Lights ..........[...]

▫ Erasing Homelink Buttons ............... 1 2 4 ▫ Reprogramming a Single Homelink Button . . . 125 ▫ Security ............................ 1 2 5 m Electrical Power Outlets .................. 1 2 6 m Cigar Lighter And Ash Receiver ............ 1 2 7 m Cupholders ........................... 1 2 8 ▫ Front Instr ument Panel Cupholders — Auto[...]

MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the r ear window . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). UNDERST ANDING THE FEA TURES OF [...]

Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cleaning, [...]

W ARNING! V ehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mir[...]

The controls for the power mirr ors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror , and set it to the center off position to pr event accidentally moving a mirror when you ar e finished adjusting the mirror . T o adjust a mirror , select left or right with the top switch, and pre[...]

T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. HANDS–FREE COMM[...]

“Call” or “Dial”). Y our cellular phone’s audio is trans- mitted through your vehicle’s ster eo system; the system will automatically mute your radio before r eceiving or sending a call. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the syst[...]

The UConnect™ system can be used with any Hands Free Pr ofile certified Bluetooth™ cellular phone. If your cellular phone has a differ ent profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts[...]

• Y ou will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. Y ou can enter any four-digit pin number . Y ou will not need to remember this pin number after the initial registration pr ocess. • The UConnect™ system will th[...]

• After the 9 Ready 9 prompt, say 9 Dial 9 or 9 Call 9 wait for the ready pr ompt followed by the name and designa- tion of a phonebook entry that you wish to dial. For example, you can say 9 Call John Doe W ork 9 . Add Names to Y our UConnect™ Phonebook • Press the “Phone” button to begin. • After the 9 Ready 9 prompt, say 9 Phonebook [...]

After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mob[...]

List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the 9 Ready 9 prompt, say 9 Phonebook List Names 9 . • The UConnect™ system will play the names of all the phonebook entries. • T o call one of the names in the list, press the ’V oice Recognition’ button during the playing of the desired name[...]

Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. T o reject the incoming call, you can disr egard the call and continue with your current conversation. Making a Second Cal[...]

Three-W ay Calling T o initiate three-way calling, pr ess the ’V oice Recogni- tion’ button while a call is in progr ess and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call T ermination T o end a[...]

• Y ou will be asked to say the name of the phone that you wish to delete. Y ou can either say the name of the phone that you wish to delete or you can say 9 All 9 to delete all the phones. Connect or Disconnect the Connection between the UConnect™ System and Y our Cellular Phone Y our cellular phone can be paired with many dif ferent electroni[...]

• The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle. UConnect™ System Features Barge In - T ouch T one Phone Inputs Y ou can use your UConnect™ system to access a voice mail system, an automated service, or any other phone numbe[...]

T urning Confirmation Prompts On/Off T urning confirmation prompts of f will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number befor e you dial it). • Press the ’Phone’ button to begin. • After the 9 Ready 9 prompt, say 9 Setup Confirmation 9 . The UConnect™ system will play the cur[...]

Help If you need assistance at any prompt or if you want to know what your options are at any pr ompt, say 9 Help 9 . The UConnect™ system will play all the options at any prompt if you ask for help. Cancel At any prompt, you can say 9 Cancel 9 and you will be returned to the pr evious menu. Emergency Assistance If you are in an emer gency , say [...]

40-20-40 Front Seat As the name implies, the seat is divided into 3 segments. The outboard seat portions ar e each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armr est/center storage compartment (if equipped). Each outboard seat is independently adjustable forwar d or backward and is equi[...]

Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle to release the seat back and adjust for comfort. W ARNING! Y ou can be seriously , even fatally injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest[...]

T o lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decr eases the lumbar support. Lumbar Adjustment 94 UNDERST A[...]

Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. The power seat controls ar e on the outboard side of the front seat cushions. Thr ee switches control the seat move- ment. The four-way switch in the center can be moved forward or backwar ds to get the most comfortable posi- tion[...]

control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Heated Seats — If Equipped The heated seat switches are located in the instr ument panel under the climate controls. The engine must be running for the heated seats to operate. T ilt Adjustment 96 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desir ed heating position and press a second time in the same dir ection to turn the heated seats OFF . If you do not purposefully turn the switch OFF , the heating element in the seat will remain activated until the ignition is turned of f. The indicators on[...]

T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the fr ont center of the hood to ensure that both latches engage. W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. 98 UNDERST ANDIN[...]

LIGHTS Interior Lights Courtesy/ dome lights are turned on when the fr ont doors are opened, when the dimmer contr ol (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob. Rotating the dimmer control to the optional fully upwar d position w[...]

turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer contr ol all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the 9 Party 9 mode because it allows the doors to stay open for extended periods of time without discharging t[...]

Headlamp Delay — If Equipped T o aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off. The headlamps will [...]

Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedures must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solven[...]

CARGO LIGHT The cargo lights ar e turned on by rotating the dimmer control to the optional fully upwar d position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature. MUL TIFUNCTION CONTROL LEVER The multifunction control lever is located on the left side of the steering colu[...]

Passing Light Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully towar d the steering wheel to switch the headligh[...]

Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever . T urn the end of the handle to select the desired wiper speed. Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desira[...]

The delay interval decreases as you r otate the knob until it enters the LO continual speed position. The delay can be regulated fr om a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less. W ARNING! Sudden loss of visibility through the[...]

TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehi[...]

DRIVER ADJUST ABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and[...]

CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at [...]

T o Set At A Desired Speed When the vehicle has reached the desir ed speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, clutch pressur e while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed cont[...]

T o V ary The Speed Setting When the speed control is on, speed can be incr eased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. T apping the ACCEL button once will result i na2m p h (3km/h) speed increase. Each time the button is tapped, speed increases so that tapping the button thr ee [...]

V ehicles equipped with a 4–speed automatic transmis- sion may exhibit several 4-3 downshifts under the above conditions. T o reduce the fr equency of the downshifts and to improve vehicle performance, it is advisable to lock out overdrive by pr essing the O/D OFF button located at the end of the gear shifter . W ARNING! Speed Control can be dang[...]

Courtesy/Reading Lights In the middle of the console are two courtesy/r eading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is r otated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter , if so equipped. These light[...]

This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units. RESET Button Use this button to reset the following displays to zer o: A verage Fuel Economy T rip Odometer Elapsed time 1 14 UND[...]

Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays. Step Button Use this button to choose or cycle through the four trip conditions. A verage Fuel Economy (A VG ECO) Shows the average fuel economy since the last reset. This display mode becomes les[...]

capacity , which corresponds to approximately 8% of tank volume. This reserve capacity was put in place to pr event the likelihood of customers running out of fuel when operating at maximum load conditions in areas wher e there ar en’t many gas stations. NOTE: The Distance T o Empty will remain equal to zero, until the vehicle r uns out of fuel o[...]

C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such condition[...]

Manual Compass Calibration NOTE: T o ensure pr oper compass calibration, make sure the compass variance is pr operly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear , you must manually put the compass into the “Calibration” mode. T o Put Into a Calibration Mode T urn on the igniti[...]

T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Pr ess the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside T emperature Because the ambient temp[...]

GARAGE DOOR OPENER — IF EQUIPPED The HomeLink t Universal T ransceiver replaces up to three r emote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal T ransceiver operates off your vehicle’s battery and chargin[...]

Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal. 1. Press and hold the two outer Hom[...]

W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inch[...]

If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with ( Program- ming ( steps 6-8 to complete the programming of a r olling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the 9 learn 9 or 9 smart 9 button. This[...]

If you live in Canada or you are having dif ficulties programming a gate operator by using the 9 Pr ogram- ming 9 procedur es (regardless of wher e you live), replace ( Programming HomeLink ( step 3 with the following: NOTE: If programming a garage door opener or gate operator , it is advised to unplug the device during the 9 cycling 9 process to p[...]

Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. DO NOT release the button. 2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink button, proceed with 9 Programming 9 step 2 For[...]

ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instrument panel below the ash receiver . A cap is attached to the outlet base indicating “Power Outlet” 12V -20A. There is an additional Power Outlet in the [...]

CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the r eceiver and then allowing the receiver to open. The cigar lighter is located above and to the left of the ash receiver . As a child safety precaution, the lighter only operates with the ignition switch ON. It heats when pushed in and pops o[...]

CUPHOLDERS Front Instrument Panel Cupholders — Automatic T ransmission Only Y our new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. T o secure the cup, place the cup to be h[...]

STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armr est to raise the cover . Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to configure the stor[...]

Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat. Lift the seat to access the storage compartment. FOLD FLA T LOAD FLOOR — IF EQUIPPED Fold Flat Load Fl[...]

W ARNING! Do not operate the vehicle with loose items stored on the load floor . While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury . Unfolding the Load Floor 1. Lift the [...]

2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to stor e the load floor . Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor . 3. Lift th[...]

4. Reverse the procedur e to put the load floor back in the secured down position befor e you operate the vehicle. PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the fr ont of the pickup box, you must use Mopar t toolbox brackets available from you dealer . [...]

Y ou can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor . Place lumber across the box in the indentations pr ovided above the wheel housings and in the bulkhead dividers to form the floor . W ARNING! The pickup box is intended for load carrying pur- poses only , not for passengers, who should sit in seats [...]

There ar e stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards acr oss the box from side to side to create separate load compartments in the pickup box. There ar e four tie-down cleats bolted to the lower sides of the pickup box that can sustain loads up to 1000 lbs (45[...]

NOTE: Dual rear wheel pickup models r equire properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. W ARNING! T o avoid inhaling carbon monoxide, which is deadly , the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the over- hanging cam[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instruments And Controls ................. 1 4 1 m Instrument Cluster ...................... 1 4 2 m Instrument Cluster Description ............. 1 4 3 m Electronic Digital Clock .................. 1 5 1 ▫ Clock Setting Procedur e................. 1 5 1 m Sales Code RBB—AM/FM Stereo Radio W ith C[...]

▫ Cassette Player Features ................ 1 5 4 ▫ CD Changer Control Capability — If Equipped ........................... 1 5 6 ▫ Radio Display Messages ................ 1 5 7 m Sales Code RAZ—AM/ FM Stereo Radio W ith Cassette T ape Player , CD Player And CD Changer Controls — If Equipped ........... 1 5 8 ▫ Operating Instructions [...]

▫ Pinch Roller Release ................... 1 6 4 ▫ Noise Reduction ...................... 1 6 4 ▫ Operating Instructions — CD Player ........ 1 6 4 ▫ Inserting The Compact Disc .............. 1 6 4 ▫ Seek Button ......................... 1 6 5 ▫ EJT CD (Eject) Button .................. 1 6 5 ▫ FF/T une/R W ........................ 1[...]

m Remote Sound System Controls — If Equipped . . 181 ▫ Radio Operation ...................... 1 8 2 ▫ T ape Player ......................... 1 8 2 ▫ CD Player .......................... 1 8 2 m Cassette T ape And Player Maintenance ....... 1 8 3 m Compact Disc Maintenance ................ 1 8 4 m Radio Operation And Cellular Phones ........[...]

INSTRUMENTS AND CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 141 4[...]

INSTRUMENT CLUSTER 142 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started. If the vehicle[...]

2. V oltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains ther e during normal driving, the electrical sys- tem should be serviced. NOTE: If the gauge pointer moves to eit[...]

7. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt W arning Light will flash or remain o[...]

12. ABS W arning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not fun[...]

NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come[...]

If brake failure is indicated, immediate r epair is necessary and continued operation of the vehicle in this condition is dangerous. Acceleration which causes the rear wheels to slip for a period of time may result in the r ed brake light illumi- nating and a brake switch code being set on ABS equipped vehicles. Depressing the brake pedal should ex[...]

hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned off or the engine is started. 21. LAMP OUT Light The LAMP OUT indicator in the instr ument cluster alerts the driver if a defective bulb or wiring circuit is detected for headlamps, turn signal lamps, and stop lamps. 22. TOW/HAUL (Automatic T rans[...]

27. Low Fuel W arning Light Glows when the pointer is between “E” and 1/8 indication mark (approximately 15% of tank vol- ume) on the fuel gauge. When the fuel gauge pointer is on “E” (equivalent to Distance T o Empty [DTE] = 0 on the overhead console if so equipped) ther e is reserve fuel capacity , which corresponds to appr oxi- mately 8%[...]

NOTE: When the ignition switch is turned to OFF , the Fuel Gage, V oltmeter , Oil Pressure and Engine Coolant T emperature gages may not show accurate r eadings. When the engine is not running, turn the ignition switch to ON to obtain accurate readings. ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A[...]

SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE T APE PLA YER AND CD CHANGER CAP ABILITY Operating Instructions NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. NOTE: When first learning the control functions, the user should set the controls as shown in the follo[...]

For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is ON. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make an[...]

Every time a preset button is used a corr esponding button number will be displayed. Balance The balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The fade control pr ovides for balance between the front and rear speakers. Pr ess the F ADE b[...]

Y ou can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player . Music Search Pressing the SEEK button while playing a ta[...]

NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display . Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactur ed under license from Dolby Laboratories Licensing Corporation. Dolby an[...]

Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to pr otect your CD player , one of the fo[...]

SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER AND CD CHANGER CONTROLS — IF EQUIPPED Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. 158 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

Power Switch, V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and r elease the Seek button to search for the next station in either the AM or FM mode. Press the [...]

Program T ype Radio Display News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when[...]

Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned. Fade The Fade control pr ovides for balance between the front and rear speakers. Push in the button and it[...]

T o Set The Radio Push-button Memory When you are r eceiving a station that you wish to commit to push-button memory , press the SET button. SET 1 will show in the display window . Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button,[...]

Press the SEEK button up or down to move the track number to skip forward or backwar d 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed aga[...]

Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch r oller will automatically retract to protect the tape from any damage. When power is r estored to the tape player , the pinch roller will automatically r eengage and the tape will resume play . Noise Reduction The Dolby Noise Reduction System* is on wheneve[...]

If the volume control is ON, the unit will switch fr om radio to CD mode and begin to play . The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: • Y ou may eject a disc with the radio OFF . The ignition switch must be in the ON or ACC position to insert a disc with the rad[...]

FF/TUNE/RW Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play . This feature plays the tracks on the se- lected disc in random order to pr ovide an interesti[...]

Time Button Press this button to change the display fr om elapsed CD playing time to time of day . Scan Button Press this button to play the first 10 seconds of each track. T o stop the scan function, press the button a second time. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available thr[...]

CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to pr otect your CD player , one of the following warning symbols may appear on your display . A CD HOT symbol indicates the player is too hot. [...]

NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station un[...]

AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency . The display will show ST when a stereo station is received. T o Set The Radio Push-Button Memory When you are r eceiving a station that you wish to commit to push-button memory , press the SET button. SET 1 will show [...]

NOTE: Changes or modifications not expressively ap- proved by the party r esponsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON befor e the CD player will operate. Inserting The Compact Disc CAUTION! This CD play[...]

If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition OFF . FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — RND/Progr[...]

Mode Button T o activate the CD changer , press the MODE button until CD information appears on the display . Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one curr ently being played. Seek Button Press the SEEK up or down to select another [...]

An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following r easons: • Excessive vibration • Disc inserted upside down • Damaged disc • W ater condensation on optics Radio Display Messages Y our radio has been designed to display certain messages when a problem is detected with the CD player . 17[...]

SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press th[...]

Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it. T une Press the T[...]

5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory . Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in[...]

Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If you insert a disc wit[...]

If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not r emoved, the radio will continue to play the non-removed CD. If the CD is removed and ther e are other CD’s in the radio, the radio will play the next CD. If the CD is removed and there ar e no other CD’s in the radio, the radio will ret[...]

PTY (Program T ype) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn of f. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently br oad- cast PTY information. T oggle the PTY b[...]

By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when sear ching for the next PTY station. If no station is found with the sel[...]

increase the volume and pr essing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode. The left hand control is a r ocker type switch with a push button in the center . The function of the left hand control is differ ent depending on which mode you are in. The following de[...]

If you press the switch up or down twice it plays the second track, three times, it will play the thir d, etc. The button in the center of the left hand switch has no function in this mode. CASSETTE T APE AND PLA YER MAINTENANCE T o keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes lo[...]

COMP ACT DISC MAINTENANCE T o keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents[...]

CLIMA TE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desir ed interior conditions. Heater Only — Fleet V ehicles The mode control (at the right of the control panel) can be set in any of the following positions: UNDERST ANDING YOUR IN[...]

NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows through the outlets located in the instrument panel. Recirculation Modes (Panel or Bi-Level ) Select the recir culation modes when the [...]

T emperature Control The rotary knob at the center of the control panel contr ols the temperature of the inte- rior air . Y ou can choose your degree of comfort by r otating the knob. The coldest tem- perature setting is to the ex- treme left (blue r egion) and the warmest setting is to the extreme right (r ed region) of the rotation. Air Condition[...]

snowflake button shows that the air conditioning is on. Press the button a second time to turn the air condition- ing off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compr essor will cycle on and off to maintain comfort and incr ease fuel economy . The mode c[...]

Floor Outside air flows primarily through the floor out- lets located under the instrument panel. Mix Outside air flows in equal proportions thr ough the floor and defroster outlets, and the air conditioning may be on. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield, a[...]

T emperature Control The rotary knob at the center of the control panel contr ols the temperature of the inte- rior air . Y ou can choose your degree of comfort by r otating the knob. The coldest tem- perature setting is to the ex- treme left (blue r egion) and the warmest setting is to the extreme right (r ed region) of the rotation. Circulation T[...]

Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear W indow Defroster and Heated side view mirrors ar e activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. T urning Off the ignition will deactivate the Electric Rear W indow Defroster and Heated side view [...]

Air Conditioning Operation T o turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be dir ected through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Press the button a second time to turn t[...]

Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recir culate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior . See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: [...]

Mix Outside air flows in equal proportions thr ough the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defr oster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even i[...]

Dual Zone T emperature Control Use this control to r egulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature contr ol slides for both the driver and front passenger . The blue area of the scale indicates cooler temperatures while the r ed area indicates warmer temperatures. Electric R[...]

edges of the instrument panel. The demisters also pr o- vide extra air ducts for circulation. They ar e in operation whenever the Floor , Mix or Defrost modes ar e in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time. This is a normal condition that occurs if the air conditioning sys[...]

speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigar ette smoke, perfumes, etc.) from sticking to the windows. Contaminates incre[...]

Operating Tips Chart 198 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

ST ARTING AND OPERA TING CONTENTS m Ignition/Starter Switch ................... 2 0 4 ▫ Lock .............................. 2 0 4 ▫ O f f ............................... 2 0 4 ▫ O n ................................ 2 0 4 ▫ Start .............................. 2 0 4 ▫ A C C .............................. 2 0 5 ▫ Manual T ransmission Key [...]

▫ Operating Precautions .................. 2 1 6 ▫ Cooling System T ips — Automatic T ransmission ........................ 2 1 6 m T ransmission Shifting .................... 2 1 8 ▫ Four-Speed Overdrive Automatic T ransmission — If Equipped ............. 2 1 8 ▫ Manual T ransmission – 5–Speed (NV - 4500) — If Equipped ...........[...]

▫ T ire Loading And T ire Pressur e ........... 2 4 7 m T ires—General Information ................ 2 5 1 ▫ T ire Pressur e ......................... 2 5 1 ▫ T ire Inflation Pressur es ................. 2 5 2 ▫ Radial-Ply T ires ...................... 2 5 5 ▫ Compact Spare T ire — If Equipped ......... 2 5 5 ▫ T ire Spinning .......[...]

▫ T railer T owing — Hitches ............... 2 7 5 ▫ Connecting T railer Lighting And Electric T railer Brakes ........................ 2 7 6 ▫ T railer W eight And T railer T ongue W eight .... 2 7 8 ▫ T railer T owing Information (Maximum T railer W eight Ratings) ......... 2 7 9 ▫ T railer T owing Mirrors — If Equipped ...... 2 7 9[...]

m Driving Off-Road ....................... 2 9 2 m T raction ............................. 2 9 3 m Engine Data Plate ...................... 2 9 4 ST ARTING AND OPERA TING 203 5[...]

IGNITION/ST ARTER SWITCH LOCK Locks the automatic transmission shift control into the P ARK position. It also engages the steering wheel lock (if equipped) when the steering wheel is turned. NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P). OFF Unlocks the steer[...]

ACC Allows the electrical accessories to be used when the engine is not running. Manual T ransmission Key Release Button T o remove the key on vehicles equipped with manual transmissions, turn the key to the Lock position and press the button to remove the ignition key . Key Reminder An alarm will sound to remind you if the key is left in the ignit[...]

• A heated intake air system both improves engine starting and reduces the amount of white smoke generated by a warming engine. Normal Starting Procedure — Engine Manifold AirT emperature Above 66°F (19°C) Observe the Instrument Panel Cluster lights when start- ing the engine. 1. Always apply the parking brake. 2. Shift into P ARK for an auto[...]

CAUTION! Do not crank engine for more than 15 seconds at a time as starter motor damage may result. T urn key to OFF and wait at least two minutes before trying again. 5. When the engine starts, release the key . 6. Check to see that there is oil pressur e. 7. Release the parking brake. Starting Procedure — Engine Manifold Air T emperature Below [...]

• After the W AIT TO ST ART light goes of f, turn the ignition key to ST AR T . Do not press the accelerator during starting. • Check to see that there is oil pr essure. • Allow the engine to idle at fast idle for about three minutes until the manifold heaters have completed the post-heat cycle. • Release the parking brake and drive. NOTE: [...]

• Heat generated by the manifold heaters dissipates rapidly in a cold engine. If more than two minutes pass between the time the W AIT TO ST ART light goes OFF and the engine is started, recycle the manifold heaters by turning the ignition OFF and then back ON. • If the vehicle is driven and vehicle speed exceeds 18 mph (29 km) before the manif[...]

W ARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. NOTE: The engine may run r ough until the air is forced from all the fuel lines. Starting Fluids W ARNING! ST AR TING FLUIDS or flammable liquids are NEVER TO BE USED in[...]

W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death. NORMAL OPERA TION Observe the following when the engine is operating. • All message center lights are of f. • Check Engine Lamp is off. • Engine Oil Pressur e is above 10 psi (69 kPa) at idle. • Low Oi[...]

Fuel Operating Range *No. 1 diesel fuel should only be used where extended arctic conditions (-10°F/-23°C) exist. NOTE: • Use of Climatized Diesel Fuel or Number 1 Diesel Fuel results in a noticeable decr ease in fuel economy . • Climatized Diesel Fuel is a blend of Number 2 and Number 1 Diesel Fuels which reduces the temperatur e at which wa[...]

W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10–1 15 volt electrical cord could cause electrocution. NOTE: The block heater will requir e 1 10 V olts AC and 6.5 Amps to activate the heater element. Block Heater Usage A. T emperatures below 0°F (-18°C) • Block Heater Required for 15W -40 • Block Heater Recommende[...]

Arctic Operation Where ther e are no provisions to keep the engine warm when it is operating in ambient temperatures consistently below (-10°F/-23°C), use 5W -40 synthetic engine oil and fuel that meets the requir ements in Section 7, “Mainte- nance Procedur es,” Engine Oil Selection. Engine W arm-Up A void full throttle operation when the en[...]

• automatic transmission is in Park (P) • vehicle speed is zero • Applying the throttle will cancel fast idle • If the engine is equipped with an aftermarket exhaust brake (manual transmissions only), operating the ex- haust brake at idle will greatly impr ove warm up rate and will help keep the engine close to operating temperature during [...]

Engine Speed Control CAUTION! Prevent overspeeding the engine going down hill. When descending steep grades, use a combination of gears and service brakes to control vehicle/engine speed. Overspeed can cause severe engine damage. Operating Precautions A void Overheating The Engine The temperature of the coolant (a mixtur e of 50% ethylene-glycol an[...]

• Highway Driving — reduce your speed. • Up Steep Hills — select a lower transmission gear , but try and keep the torque converter locked. • Air Conditioning — turn it off temporarily . Do Not Operate The Engine W ith Low Oil Pressure When the engine is at normal operating temperature, the minimum oil pressur es required ar e: Idle 700 [...]

• sudden change, outside the normal operating range, in the engine operating temperature • excessive smoke • oil pressur e drop TRANSMISSION SHIFTING Four-Speed Overdrive Automatic T ransmission — If Equipped The gear shift selector display , located in the instrument panel cluster , indicates the transmission gear range (the selector is il[...]

W ARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idlin[...]

“1” First Use this position for driving up very steep hills and for engine braking at low speeds 20 mph (32 km/h) or less when going downhill. T o prevent excessive engine speed, do not exceed 25 mph (40 km/h) in this range. NOTE: Use caution when operating a heavily loaded vehicle in “2” Second or “1” First gear selections in high ambi[...]

• the engine coolant has reached normal operating tem- perature; • vehicle speed is above approximately 30 mph (48 km/h); • the “TOW/HAUL” switch has not been activated; • transmission has reached normal operating tempera- ture. The transmission will downshift from Over drive to Drive if the accelerator pedal is fully depressed at vehic[...]

occurs, press the “T OW/HAUL” button. This will im- prove performance and r educe the potential for transmis- sion overheating or failur e due to excessive shifting. T orque Converter Clutch A featur e, designed to improve fuel economy , has been included in the automatic transmission on your vehicle. A clutch within the torque converter engage[...]

T ruck models with manual transmission are equipped with a clutch interlocking ignition system. The clutch pedal must be fully depressed to start the vehicle. Fully depress the clutch pedal befor e shifting gears. As you release the clutch pedal, lightly depr ess the accelera- tor pedal. When launching a stationary vehicle, keep the engine speed lo[...]

avoid overspeeding the engine and clutch. For accelera- tion at speeds less than 15 mph (25 km/h), 2nd gear is recommended. CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. Manual T ransmission — 6-Speed (NV -5600) — If Equipped NOTE: The parking br[...]

together and the overall close ratios enable the driver to optimize available engine power with road speed. For improved clutch life, all six forwar d gears should be used. For steady highway driving with light acceleration, 6th gear is recommended. When shifting fr om 4th to 5th gear , apply side effort away and forwar d without push- ing hard eno[...]

CAUTION! When descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause valve damage. FOUR-WHEEL- DRIVE OPERA TION — IF EQUIPPED • Four-Wheel-Drive Dodge Ram T rucks ar e equipped with either a Manually Shifted transfer case or an Electronically Shifted transfer case. See the operating[...]

The 4-wheel-drive light (4WD), located in the instrument cluster , alerts the driver that the vehicle is in 4-wheel drive and that the front and r ear driveshafts are locked together . This light illuminates when the transfer case is shifted to either the 4H or 4L positions. Ther e is no light for the 2H or N (Neutral) positions. When operating you[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission p[...]

Shifting Procedure - Manually Shifted T ransfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). W ith the vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after co[...]

NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be requir ed for clutch teeth alignment and shift completion to occur . The pre- ferred method is with the vehicle r olling 2 to 3 mph (3 to 5 km/h). A void [...]

position - see Shifting Procedur e section for specific shifting instructions. The 4HI and 4LO positions ar e designed for loose, slippery road surfaces only . Driving in the 4HI and 4LO positions on dry hard surfaced r oads may cause increased tir e wear and damage to the driv- eline components. NOTE: The transfer case Neutral (N) position is sele[...]

NOTE: Before r etrying a selection, make certain that all the necessary requir ements for selecting a new transfer case position have been met. T o retry the selection, turn the control knob back to the curr ent position, wait five (5) seconds, and retry selection. T o find the shift require- ments, refer to the 9 Shifting Pr ocedure 9 for your tra[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission p[...]

Shifting Procedure - Electronically Shifted T ransfer Case NOTE: If any of the requir ements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requir ements for th[...]

return the contr ol knob back to the original position, make certain all shift requir ements have been met, wait five (5) seconds and try the shift again. NOTE: If all the requir ements to select a new transfer case position have been met, the current position indica- tor light will turn OFF , the selected position indicator light will flash until [...]

Preferred Procedure 1. W ith engine RUNNING, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL (depr ess clutch on manual transmissions). 3. While still rolling, rotate the transfer case contr ol switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back[...]

LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differ ential provides additional traction on snow , ice, mud, sand and gravel, particularly when there is a dif ference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit per- forms similarly [...]

P ARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster r ed brake warning light will come on and flash to indicate that the parking brake is applied. Y ou must be sure that the parking brake i[...]

W ARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury . Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear . Failure to do so may allow the vehicle to roll and cause damage or injury . • Leaving children in a vehicle unatten[...]

Brake Noise During normal operation of the brake system certain noises may be present fr om time to time. Occasional 9 groan 9 or 9 squeal 9 noises may occur during normal operation of the brake system which may not be indica- tive of a problem. These noises may be hear d at any time the brakes are applied but may be mor e noticeable during the fir[...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

ABS W arning Light The Anti-lock Brake System includes an amber warning light, located in the instrument cluster . When the light is illuminated, the Anti-lock Brake System is not function- ing. The system reverts to standar d non-anti-lock brakes. W ARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accide[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d have[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ( ....blank.... ( = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = Aspec[...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corr esponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be [...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your [...]

Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size and cold tire inflation pressur es specified on the T ire and Loading Information placard and the V ehicle Loading section o[...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the avail[...]

250 ST ARTING AND OPERA TING[...]

W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressure is essential to the safe and satisfactory oper[...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tire rolling r esistance and results in higher fuel consumption. 3. Ride Comfort and V ehicle Stability—[...]

check tire pr essure. Do not make a visual judgement when determining proper inflation. Radial tir es may look properly inflated even when they ar e underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which coul[...]

T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressure is very important. Increased tir e pressure and r educed vehicle loading may be requir ed for h[...]

Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial [...]

Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spar e tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car[...]

T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent gr ooves, the ti[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can cause unpredictable handling and stress to steeri[...]

Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . SUPPLEMENT AL TIRE PRESSURE INFORMA TION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo[...]

These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. T ire chain use is permitted only on the rear tir es of Ram 4X2 trucks. NOTE: The use of class “U” chains is permitted on the front and r ear of 4X4, 2500 Ram T rucks with L T245/ 70R17E tires. NOTE: The use of class “U” chains is permitted on th[...]

SNOW TIRES Snow tires should be of the same size and type constr uc- tion as the front tir es. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requir ement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressur es under any load condition. While studded tire[...]

Follow the recommended tir e rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More fr equent rotation is permis- sible if desired. The r easons for any rapid or unusual wear should be corrected prior to r otation being per- formed. NOTE: On Canadian vehicles only , if your Ram truck is equ[...]

Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tir e in a set. T o check if tires ar e even, lay a straight edge across all four tires. The straight edge should touch all the tir es. CAUTION! 3500 Dual Rear T ires have only one approved direc- tion of rotation. This is to accommodate t[...]

ENGINE RUNA W A Y W ARNING! In case of engine runaway due to flammable fumes from gasoline spills or turbocharger oil leaks being sucked into the engine do the following to help avoid personal injury and/or vehicle damage: 1. Shut off engine ignition switch. 2. Using a CO 2 or dry chemical type fire extin- guisher , direct the spray from the fire e[...]

Diesel fuel is seldom completely free of water . T o prevent fuel system trouble, drain the accumulated water fr om the fuel/water separator using the fuel/water separator drain provided. If you buy good quality fuel and follow the cold weather advice above, fuel conditioners should not be requir ed in your vehicle. If available in your area, a hig[...]

CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. W ARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury . • The volatil[...]

A void Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system which is not covered by the warranty . Proper maintenance of the engine fuel filter and fuel tank is essential. (See Section 7 for Maintenance Procedur es). NOTE: Climatized diesel fuel is a blend of Number 2 and Number 1 Dies[...]

Number 2 Diesel Fuel Specifications Fuel Properties - No. 2 - Diesel Reference V iscosity - 1.9to 4.1 centistokes (ASTM D-445) Cetane Number - 40 min. (ASTM D613) Sulfur Content -.05% by weight (ASTM D-2622) W ater & Sediment - less than 0.05 % by volume (ASTM D-2709) Carbon Residue - Less than.35% (Ramsbottom ASTM D-524 Flash Point - 125°F mi[...]

VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar . This label contains the month and year of manufacture, Gross V ehicle W eight Rating (GVWR), Gross Axle W eight Rating (GA WR) front and r ear , and[...]

T ire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tir e size listed. Inflation Pressure This is the cold tire inflation pr essure for your vehicle for all loading conditions up to full GA WR. Curb W ei[...]

Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose [...]

TRAILER TOWING All Dodge Ram Pickup trucks ar e intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package. See your Dodge dealer for package content. T [...]

CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer . Doing so may damage your vehicle. • When first towing a trailer , limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. Perform the maintenance listed in the “Maintenance Schedules” section of this manual (Section [...]

must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross V ehicle W eight Rating. W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Axle Lubricant and T railer T owing 2500/3500 Models ?[...]

• Use an approved wiring harness connector on the trailer . Standard equipment on all RAM pickup mod- els provides a 4-way trailer tow connector located under the bumper . This connector contains the follow- ing vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/turn lamp, and ground. W ith the optional T railer T ow Prep package [...]

W ith a Class III Hitch, your vehicle can be equipped to tow trailers with a Gross T railer W eight (GTW) of 5,000 lbs (2 268 kg) maximum. Factory-installed rear step bumpers are rated a Class III hitch. T ongue weight must be equal to at least 10% of the gross trailer weight (GTW), but no more than 15% of the GTW . A frame mounted hitch of up to C[...]

CAUTION! Adding lights or electrical devices to the headlamp/ park lamp circuit can be accomplished by connecting to the standard 4-way trailer tow connector located behind the rear bumper . The maximum current ca- pacity for the park lamp circuit should not exceed 15 amps total (a typical park lamp bulb can draw from 0.5 to 1.0 amperes of current)[...]

T railer Weight and T railer T ongue Weight Gross T railer W eight (GTW) means the weight of the trailer plus the weight of all cargo, consumables and equipment loaded on the trailer when in actual under- way towing condition. The recommended way to mea- sure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trail[...]

NOTE: When towing a trailer , the following require- ments must be adhered to: • GCWR must not be exceeded • T otal weight must be distributed between the tow vehicle and the trailer such that the following four (4) ratings are not exceeded: 1. GVWR 2. GTW 3. T ongue weight rating for the trailer hitch utilized (This requirement may limit the a[...]

NOTE: • These mirrors ar e power adjustable and heated. • The passenger side main mirror is flat. Cooling System Tips — T railer T owing T o reduce potential for engine and transmission over - heating, take the following actions in high ambient temperatures: • City Driving— when stopped, put the transmission in N (Neutral) and increase th[...]

• Highway Driving— reduce your speed. • Air Conditioning— turn it off temporarily . • Hilly T errain— T urn overdrive of f. See Cooling System Operating information in the Service and Maintenance section of this manual for more infor - mation. Automatic T ransmission Oil T emperature Warning Light All vehicles with heavy duty transmissi[...]

If your vehicle has an automatic transmission and you tow a trailer frequently , change transmission fluid and filter every 30,000 miles (48 000 km) SNOWPLOW Snowplow Prep Packages ar e available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow . NOTE: Before installation of a snowplow[...]

Before plowing • Check the hydraulic system for leaks and proper fluid level. • Check the mounting bolts and nuts for proper tight- ness. • Check the runners and cutting edge for excessive wear . The cutting edge should be 1/4 to 1/2 inch above ground in snow plowing position. • Check that snowplow lighting is connected and func- tioning pr[...]

of the plow . Front end tow-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tir e wear . The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equip- ment following the recommendations pr ovided by the specific snowplow ma[...]

NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside tempera- ture display will show higher temperatur es than the outside ambient temperature. The higher displayed tem- perature is due to blocked or r educed airflow to the underhood ambient temperatur e sensor by the snow- plow . This is common and outside [...]

RECREA TIONAL TOWING — 4–WHEEL DRIVE VEHICLES (BEHIND MOTORHOME, ETC.) CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the Manual Shift and Electronic Shift transfer cases must be shifted into Neutral (N) for recr eational towing. Automatic transmissions must be[...]

5. Shift transfer case lever into N (NEUTRAL). 6. Start the engine. 7. Shift automatic transmission into Reverse (R). 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with the transmission in Drive (D). 10. Shut OFF the engine and place the ignition key to the unlocked OFF position. 1 1. [...]

4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions. 5. Shift transfer case lever to desired position. 6. Shift automatic transmission into P (Park). W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the N (NEUTRAL) position without first fully engaging [...]

CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts. 1. Bring vehicle to a complete stop. 2. Shut OFF the engine. 3. Place ignition key in the ON position. 4. Depress the brake pedal. 5. Shift automatic transmission to Neutral (N) [...]

NOTE: Items 1 through 5 ar e requirements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until the 4 seconds elaspes and the shift has been completed. If any of these requir e- ments (with the exception of 3 - Key ON) are not met prior to depressing the Neutral (N) button or ar e no longer met dur[...]

4. Depress the brake pedal. 5. Shift automatic transmission to Neutral (N) or depress clutch on manual transmission. 6. Using the point of a ballpoint pen or similar object, depress the r ecessed transfer case Neutral (N) button for 1 second. 7. After the Neutral (N) indicator light turns off release the Neutral (N) button. 8. After the Neutral (N)[...]

W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission positio[...]

If you must back down a hill, back straight down using REVERSE gear . Never back down in NEUTRAL, or diagonally across the hill. When driving over sand, mud, and other soft terrain, shift to low gear and drive steadily . Apply the accelerator slowly to avoid spinning the wheels. DO NOT REDUCE the tire pr essures for this type of driving. NOTE: Afte[...]

3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop. ENGINE DA T A PLA TE Use the information from the engine data plate when discussing service or sourcing parts for your engine. The engine [...]

WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Lights .................. 2 9 6 m Adding Fuel — 24–V alve Cummins T urbo Diesel ............................... 2 9 7 m Jack Location .......................... 2 9 8 ▫ All Models .......................... 2 9 8 m Changing A Flat T ire .................... 2 9 9 ▫ Removing The Spare T [...]

HAZARD W ARNING LIGHTS The Hazard W arning switch is mounted on the top of the steering column as shown in the illustration. T o engage the Hazard W arning lights, depress the button on the top of the steering column. When the Hazard W arning switch is activated, all directional turn signals will flash off and on to warn oncoming traf fic of an eme[...]

ADDING FUEL — 24–V AL VE CUMMINS TURBO DIESEL W ARNING! A fire may result if fuel is pumped into a portable container that is on a truck bed. Y ou could be burned. Always place fuel containers on the ground while filling. NOTE: When a diesel engine is allowed to run out of fuel, air is pulled into the fuel system. Y ou may try priming as descri[...]

4. Repeat the procedure if the engine does not start. CAUTION! Do not engage the starter motor for more than 15 seconds at a time. Allow two minutes between the cranking intervals. NOTE: The engine may run r ough until the air is forced from all the fuel lines. JACK LOCA TION All Models The jack and jack tools are stor ed under the passenger seat. [...]

W ARNING! The jack is designed to use as a tool for changing tires only . The jack should not be used to lift the vehicle for service purposes, unless suitable sup- ports are placed under the vehicle as a safety mea- sure. The vehicle should be jacked on a firm level surface only . A void ice or slippery areas. W ARNING! After using the jack and to[...]

It is recommended that you stow the flat or spar e to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only . Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure W ARNING! Getting under a jacked-up vehicle is dangerous. The vehicle c[...]

Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in P ARK (automatic transmission) or REVERSE (manual transmission). On four-wheel drive vehicles, shift the transfer case to the “4L” position. W ARNING! Do not attempt to change a tire on the side of the vehi[...]

Instructions W ARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly before[...]

When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending to the rear . Connect the jack tube extension and wheel wrench. Before raising the wheel off the ground, make sure that the jack[...]

4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. 304 WHA T TO DO IN EMERGENCIES[...]

W ARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel [...]

hand, it may be necessary to use the jack drive tube in order to lower the jack. Stow the r eplaced tire, jack, and tools as previously described. 9. Adjust the tire pressur e when possible. NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. Hub Caps The hub caps must be removed befor e raising the veh[...]

Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the gr ound when tightening to insure wheel centering and maximum wheel clamping. Dual wheel models requir e a spe[...]

1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go thr ough the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel [...]

wheel. The nuts should then be tightened to recom- mended torque. T ighten the nuts to final torque in increments. Pr ogress around the bolt cir cle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended tor ques are shown in the following chart. Disc Wheels T ype Nut Stud Size T orque Ft. Lbs.[...]

JUMP-ST ARTING W ARNING! T o prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other . Keep open flames or sparks away from battery vent holes. Always wear eye protection when work- ing with batterie[...]

CAUTION! Use the Jump Start Procedure only when the charge indicator (if equipped) in both batteries is dark in the center . Do not attempt jump starting when either battery charge indicator (if equipped) is bright or yellow . If charge indicator (if equipped) has a green dot in the center , failure to start is not due to a discharged battery and c[...]

2. Connect one end of the other jumper cable to negative (-) post of booster battery . Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery . Make sure a good connection is made, free of dirt and gr ease. W ARNING! • Do not connect the cable to the negative post of the discharge[...]

W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. With Portable Starting Unit There ar e many types of these units available. Foll[...]

transmission selector in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and r educe the risk of transmis- sion failure during pr olonged efforts to free a stuck vehicle. EMERGENCY T OW HOOKS — IF EQUIPPED Y our vehicle may be equipped with emergency tow hooks. W ARNING! Chains are not recomm[...]

TOWING A DISABLED VEHICLE Proper towing or lifting equipment is r equired to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instr uctions. Use of safety chains is mandatory . Attach a tow bar or other towing device to the main structural members of the vehicle?[...]

[...]

MAINT AINING YOUR VEHICLE CONTENTS m Engine Compartment .................... 3 2 0 ▫ 5.9L/5.9L HO Cummins T urbo Diesel ....... 3 2 0 m Onboard Diagnostic System (OBD II) ......... 3 2 1 m Replacement Parts ...................... 3 2 2 m Dealer Service ......................... 3 2 2 m Service Information ..................... 3 2 2 m Maintenance[...]

▫ Body Lubrication ..................... 3 4 0 ▫ W indshield W iper Blades ................ 3 4 1 ▫ W indshield W ashers ................... 3 4 1 ▫ Exhaust System ...................... 3 4 2 ▫ Cooling System ....................... 3 4 3 ▫ F a n ............................... 3 4 7 ▫ Charge Air Cooler (Inter-Cooler) .......... 3 4 [...]

m Replacement Light Bulbs ................. 3 6 7 m Bulb Replacement ...................... 3 6 7 ▫ Headlight (Halogen)/Front Park And T urn Lights ............................. 3 6 7 ▫ T ail, Stop, T urn And Backup Lights ......... 3 7 1 ▫ Center High-Mounted Stoplight W ith Cargo Light .............................. 3 7 3 ▫ Cab T op Clear[...]

ENGINE COMP ARTMENT 5.9L/5.9L HO CUMMINS TURBO DIESEL 320 MAINT AINING YOUR VEHICLE[...]

ONBOARD DIAGNOSTIC SYSTEM (OBD II) CARB emission control vehicles ar e equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating pr operly , your vehicle will provide excellent performance and fuel [...]

REPLACEMENT P ARTS Use of genuine Mopar t parts for normal/scheduled maintenance and repairs is highly r ecommended to in- sure the designed performance. Damage or failur es caused by the use of non-Mopar parts for maintenance and repairs will not be cover ed by the manufacturer’s warranty . DEALER SERVICE Y our dealer has the qualified service p[...]

NOTE: Failure to perform maintenance service at the specified intervals as outlined in the Maintenance Schedules may void provisions of your V ehicle W arranty . CAUTION! T o maintain your vehicle safely follow these guide- lines: • W atch your vehicle’s mileage and check your Mainte- nance Schedules regularly for r equired servicing. Ex- cessi[...]

• Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. • If an engine has been operating and the coolant is hot, allow the engine to cool before you slowly loosen the filler cap and relieve the pr essure from the cooling system. • T o [...]

MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there ar e fixed maintenance intervals, there ar e other items that should operate satisfactorily without periodic maintenance. However , if a malfunction of these item[...]

Checking the vehicle while it’s on level ground will also improve the accuracy of the oil level r eadings. Add oil only when the level on the dipstick is below the “ADD” mark. The total capacity from the low mark to the high mark is 2 quarts (1.9 liters). Never operate the engine with oil level below the “ADD” mark or above the upper “S[...]

• Driving in dusty conditions. • Frequent trailer towing. • T axi, police, or delivery service (commercial service). • Off-r oad or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% thr ottle). If ANY of these apply to you, then change your engine oil at every interval shown [...]

NOTE: The same oil change interval is to be followed for synthetic oil as for petroleum based oil. Also, syn- thetic oil must meet the same performance specifications as petroleum oil. Engine Oil Filter Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct part number . The engine oil filter should be changed at every engine oil[...]

Always check the condition of the used oil. This can give you an indication of some engine problems that might exist. • Thin, black oil indicates fuel dilution. • Milky discoloration indicates coolant dilution. Clean the area ar ound the oil filter base. Remove the filter from the underside of the vehicle using a cap style oil filter wrench. Cl[...]

Apply a light film of lubricating oil to the sealing surface of the filter gasket before installing the filter . CAUTION! Overtightening may distort the threads or damage the filter element seal. Install the filter as specified by the filter manufacturer . T urn the filter 3/4 to one full turn after making contact with the gasket. Check the conditi[...]

Disposing Of Used Engine Oil And Filter Care should be taken in disposing of the used engine fluids from your vehicle. Used fluids, indiscriminately discarded, can pr esent a problem to the environment. Contact your local dealer , service station, or governmen- tal agency for advice on recycling pr ograms and where used fluids and filters can be sa[...]

Do not remove the top of the air filter housing to inspect the filter element on your diesel engine under normal operating conditions. The clear plastic housing on the Filter Minder™ allows you to view the amount of air pressur e drop across the filter element. It consists of a diaphragm and a calibrated spring sealed inside the plastic housing. [...]

A visual inspection of the air cleaner filter element is never recommended under normal cir cumstances. A badly restricted element may appear clean while a soiled element may be quite effective in filtering particles without restricting air flow . Rely on the Filter Minder™ to determine when a filter change is necessary . After a new filter eleme[...]

Draining Fuel/W ater Separator Filter CAUTION! Do not drain the fuel/water separator filter when the engine is running. Drain a small amount from the fuel/water separator filter periodically or when the W A TER IN FUEL indicator lamp is on. Pull outward on the drain valve lever , located on the side of the filter , and allow any accumulated water t[...]

W ARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. Priming if the engine has run out of fuel 1. Add a substantial quantity of fuel to the tank 5 to 10 gallons (19L to 38L). 2. Crank the engine for 1 to 2 seconds. If the [...]

W ARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. NOTE: Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system. Hence, use of these fuels will void the warranty on the engine[...]

T o determine the battery charge, check the battery test indicator (if equipped) on top of each battery . If the test indicator (if equipped) appears light or yellow , replace the battery . NOTE: Replacement batteries should both be of equal capacity to prevent damage to the vehicle’s char ging system. CAUTION! It is essential when replacing the [...]

Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decr eases to 0°F (-18°). For the same de- crease in temperatur e, the engine requires twice as much power to crank at the same RPM. The use of 120 V AC powered battery blankets will gr eatly increase starting capability at low temperatures. Suitable batter[...]

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and r ecycling equ[...]

Front Suspension Ball Joints The ball joints originally supplied with the vehicle are permanently lubricated at the factory and do not requir e service. The ball joints and seals should be inspected whenever the vehicle is serviced for other reasons. Steering Linkage — Inspection Whenever the vehicle is hoisted, all steering linkage joints should[...]

Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner . This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid [...]

directed on the container , aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust[...]

Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Coolant protection checks should be made every 12 months (prior to the onset of freezing weather , where applicable). If coolant is dirty or rusty in appearance, the system[...]

Coolant bottle level check The coolant reserve system pr ovides a quick visual method of determining that the coolant level is adequate. W ith the engine idling, and warmed to the normal operating temperature, the level of the coolant on the coolant bottle should be between the fluid level marks. Check the coolant level whenever the hood is raised.[...]

NOTE: Mixing coolant types will decrease the life of the engine coolant and will requir e more frequent coolant changes. When additional coolant is needed to maintain the proper level, add the r ecommended concentration of antifreeze and water to the overflow bottle. Do not overfill. NOTE: Failure to follow the antifr eeze concentration and replace[...]

CAUTION! Mixing of coolants other than specified (HOA T), may result in engine damage that may not be cov- ered under the new vehicle warranty , and decreased corrosion protection. If a non-HOA T coolant is intro- duced into the cooling system in an emergency , it should be replaced with the specified coolant as soon as possible. Do not use plain w[...]

W ARNING! Never add coolant when the engine is overheated. Do not loosen or remove the pressure cap to cool an overheated engine. Heat causes pressure build up in the cooling system. T o prevent scalding or injury , do not remove the pressure cap while the system is hot or under pressure. CAUTION! Recheck the cooling system to insure total system i[...]

degrees Fahr enheit. This cooling process enables more efficient burning of fuel r esulting in fewer emissions. T o guarantee optimum performance of the system, keep the surfaces of the charge air cooler , condenser and radiator clean and free of debris. Periodically check the hoses leading to and from the char ge air cooler for cracks or loose cla[...]

The brake master cylinder has a translucent plastic reservoir . On the outboard side of the r eservoir , there is a “FULL” dot and an “ADD” dot. The fluid level must be kept within these two dots. Do not add fluid above the full mark because leakage may occur at the cap. W ith disc brakes the fluid level can be expected to fall as the brake[...]

W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture. CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage a[...]

Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system. In the event of leakage or other malfunction, the system must be replaced. Propeller Shaft Universal Joints Cross T ype (No fittings) — Relubrication of this type of universal joint is not requir ed. The seals should be inspected for external leaks or damage.[...]

encountered in some of f-highway types of service, will requir e draining and refilling the axle to avoid damage. Limited-Slip Differentials in vehicles equipped with 10.5”/1 1.5” Axles DO NOT REQUIRE any limited slip oil additive (friction modifiers). T ransfer Case — If Equipped Fluid Level Check This fluid level can be checked by removing [...]

Lubricant Selection for NV -5600 (6-Speed Manual T ransmission) — If Equipped This transmission does not requir e periodic changing. If it becomes necessary to add fluid or change the fluid, be sure to use the same lubricant or equivalent. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. Automatic T ransmi[...]

6. W ipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. a. If the fluid is hot, the r eading should be in the crosshatched ar ea marked “OK”. b. If the fluid is warm, the reading should be between the two holes. If the fluid level indicates low , add sufficient fluid to bring to the pr oper level. Fluid is added[...]

It is important that proper lubricant is used in the transmission. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. A band adjustment and filter change should be made at the time of the oil change. The fluid and filter should be changed and the bands adjusted as specified in the Maintenance Schedule (Sec- ti[...]

• If a bearing assembly is accidentally separated when servicing the brake rotors, it should be r eplaced. Rear Wheel Bearings Clean and repack when brake linings ar e replaced or rotors r esurfaced. Selection Of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owne[...]

Noise Control System Required Maintenance & W arranty For 3500 T wo-Wheel Drive and Four-Wheel Drive mod- els over 10,000 lbs. (4 535 kg) Gross V ehicle W eight Rating. All vehicles built over 10,000 lbs. (4 535 kg) Gross V ehicle W eight Rating and manufactured for sale and use in the United States are r equired to comply with the Federal Gove[...]

or suspected. Proper maintenance of the entir e vehicle will help the effectiveness of the noise contr ol systems. Exhaust System Inspect the entire exhaust system for leaks and damaged parts. Devices such as hangers, clamps, and U-bolts should be tight and in good condition. Damaged compo- nents, burned or blown out mufflers, burned or r usted out[...]

• AIR CLEANER − Removal of the air cleaner . − Removal of the air cleaner filter element from the air cleaner housing. − Removal of the air ducting. • EXHAUST SYSTEM − Removal or rendering inoperative exhaust system components including the muffler or tailpipe. • ENGINE COOLING SYSTEM − Removal or rendering inoperative the fan clutc[...]

Maintenance Log and Service Chart — 24 V alve Cummins T urbo Diesel Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed. MILES 7,500 15,000 22,500 30,000 37,500 45,000 52,500 60,000 KILOMETERS 12 000 24 000 36 000 48 000 60 000 72 000 84 000 96 00[...]

Noise Systems Maintenance Chart and Service Log — Insert Month, Day , Y ear under column mileage closest to the mileage at which service was performed. MILES 67,500 75,000 82,500 90,000 97,500 84,000 105,00 1 12,500 KILOMETERS 108 000 120 000 132 000 144 000 126 000 156 000 168 000 181 000 Exhaust system- inspect Air cleaner assembly-inspect ODOM[...]

Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and r oad surfaces during other seasons, are highly corrosive to the metal in your vehi[...]

• A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose o[...]

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Y our dealer has touch up paint to match the co[...]

Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer . Do not use scrapers or other sharp instru- ments whic[...]

FUSE AND RELA Y CENTER Y our vehicle is equipped with a fuse and relay center located in the engine compartment near the battery . Located on the underside of the cover is a label that identifies each component. 1. Disconnect the battery negative (-) cables fr om the right and left batteries before r emoving the cover . 2. Use specified fuses only [...]

REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Bulb No. Overhead Console Lights ............... T S 212-2 Dome Light ............................ 7679 All of the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not appr oved. LIGHT BULBS — Outside Bulb No. Back-Up .............................. 3057 Center High Mounted Stop Lam[...]

368 MAINT AINING YOUR VEHICLE[...]

2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperatur e sensor between the headlight assembly and the frame. MAINT AINING YOUR VEHICLE 369 7[...]

3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 370 MAINT AINING YOUR VEHICLE[...]

5. T wist connector on turn signal/park light bulb 1 ⁄ 4 turn and remove connector and bulb fr om housing. 6. Remove housing from vehicle with headlight halogen bulb in housing. 7. T wist collar on headlight halogen bulb 1 ⁄ 4 turn and remove headlight bulb fr om the housing. 8. Replace headlight or turn signal bulb. Do not touch the headlight [...]

2. Pull the housing straight out from the body , with a quick motion, to separate the housing from the body . If not pulled straight, locators may be damaged. 3. Push the red lock slide in on the connector and remove the housing from the vehicle. 4. Remove the four (4) screws from the bulb strip in the housing. 372 MAINT AINING YOUR VEHICLE[...]

5. Pull the appropriate bulb straight from the bulb strip. • T op Bulb: Park/T urn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first. Center High-Mounted Stoplight With Cargo Light 1. R[...]

2. Separate the connector holding the housing and wir- ing harness to the body . 3. T urn desired bulb socket 1 ⁄ 4 turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. 3[...]

Cab T op Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1 ⁄ 4 turn and pull it from the light assembly . MAINT AINING YOUR VEHICLE 375 7[...]

3. Pull the bulb straight from it’s socket and replace. T ailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the r ear . 376 MAINT AINING YOUR VEHICLE[...]

2. T urn socket 1 ⁄ 4 turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. MAINT AINING YOUR VEHICLE 377 7[...]

Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly . 2. Pull the entire assembly from the fender . 3. T urn socket 1 ⁄ 4 turn counterclockwise and r emove from assembly to access the bulb. 4. Pull bulb straight out from socket. 5. Reverse procedure for installation of bulbs and hous- ing. Fog Lights 1. Reach [...]

2. Pull bulb straight from the connector . 3. Reverse procedure for installation of bulbs and hous- ing. FLUID CAP ACITIES FLUID CAP ACITIES U.S. Metric Fuel 2500 Shortbed Models 34 gal. 128L 2500 Longbed Models 35 gal. 132L 3500 Shortbed Models 34 gal. 128L 3500 Longbed Models 35 gal. 132L Engine Oil 5.9L Diesel Engine I-6 12.0 qts. 1 1.4L Cooling[...]

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) P/N 501 1764AB or equivalent. Engine Oil For the proper quality and SAE Grade oil for your engine, r efer to the sec- tion 9 Main[...]

Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar t A TF+4, Automatic T ransmission Fluid T ransfer Case Mopar t A TF+4, Automatic T ransmission Fluid Manual T ransmission Fluid NV 4500 Mopar t 75W -85 Synthetic, API grade GL4, Mopar P/N 4874459, Manual T ransmission Fluid NV 5600 Mopar t manual transmission flui[...]

[...]

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ........ 3 8 4 m Maintenance Schedules — 24–V alve Cummins T urbo Diesel .......................... 3 8 4 ▫ Schedule “B” ........................ 3 8 7 ▫ Schedule “A” ........................ 3 9 6 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best ve[...]

• Off-r oad or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% thr ottle). NOTE: Most vehicles are operated under the conditions listed for Schedule 9 B 9 . Second is Schedule “A” . It is for vehicles that are not operated under any of the conditions listed under Sched- ule 9[...]

• Check the fluid levels of coolant reservoir , brake master cylinder , and transmission and transfer case (if equipped), add as needed. • Check Filter Minder™. Replace air cleaner filter element if necessary . • Check all lights and all other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • [...]

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Frequent short trips wher e the engine does not achieve full operating temperature (operating temperatur e de- fined as 190° F (66° C ) coolant temperature). • Extensive engine idling (over 10 minutes per hour of opera[...]

Miles 3,750 7,500 1 1,250 15,000 18,750 (Kilometers) (6 000) (12 000) (18 000) (24 000) (30 000) Change engine oil and engine oil filter . X X Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . X X Inspect water pump weep hole for blockage. X Replace fuel filter element. Clean the water in fuel sensor . X Change rear axl[...]

Miles 22,500 26,250 30,000 33,750 37,500 (Kilometers) (36 000) (42 000) (48 000) (54 000) (60 000) Change engine oil and engine oil filter . X X X Rotate tires. X X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . XX X Inspect drive belt, replace as r equired. X Inspect fan hub. X Inspect damper . X Inspect water pump weep hole for bl[...]

Miles 41,250 45,000 48,750 52,500 56,250 (Kilometers) (66 000) (72 000) (78 000) (84 000) (90 000) Change engine oil and engine oil filter . X X Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only . X X Inspect drive belt, replace as r equired. X Inspect water pump weep hole for blockage. X Replace fuel filter element. Clea[...]

Miles 60,000 63,750 67,500 71,250 75,000 (Kilometers) (96 000) (102 000) (108 000) (1 14 000) (120 000) Change engine oil and engine oil filter . X X X Rotate tires. X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X X Inspect drive belt, replace as r equired. X Inspect fan hub. X Inspect damper . X Inspect water pump weep hole fo[...]

Miles 78,750 82,500 86,250 90,000 93,750 (Kilometers) (126 000) (132 000) (138 000) (144 000) (150 000) Change engine oil and engine oil filter . X X Rotate tires. X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X Inspect drive belt, replace as r equired. X Change rear axle fluid. X Change front axle fluid (4X4). X Check transfer c[...]

Miles 97,500 100,000 101,250 105,000 108,750 112,500 (Kilometers) (156 000) (160 000) (162 000) (168 000) (174 000) (180 000) Change engine oil and engine oil filter . X X X Rotate tires. X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X XX Flush and replace engine coolant. X Inspect drive belt, replace as r equired. X Inspect wate[...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Change engine oil and engine oil filter . X X X Rotate tires. X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X XX Clean engine air filter canister . X Adjust valve lash clearance. X Inspect drive belts, r[...]

Miles 1 16,250 120,000 123,750 127,500 131,250 135,000 (Kilometers) (186 000) (192 000) (198 000) (204 000) (210 000) (216 000) Change front axle fluid (4X4). X X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X X Drain and refill automatic transmission fluid. Replace filter and adjust bands. X Inspection and service sho[...]

Schedule “A” Miles 7,500 15,000 22,500 30,000 37,500 (Kilometers) (12 000) (24 000) (36 000) (48 000) (60 000) [Months] [6] [12] [18] [24] [30] Change engine oil and engine oil filter . X X Rotate tir es. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X XXX Check transfer case fluid level (4X4). X Inspect water pump weep[...]

Miles 45,000 52,500 60,000 67,500 75,000 (Kilometers) (72 000) (84 000) (96 000) (108 000) (120 000) [Months] [36] [42] [48] [54] [60] Change engine oil and engine oil filter . X X X Rotate tires. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X X X X Check transfer case fluid level. X Flush and replace engine coolant at 60 [...]

Miles 82,500 90,000 97,500 100,000 105,000 (Kilometers) (132 000) (144 000) (156 000) (160 000) (168 000) [Months] [66] [72] [78] [84] Change engine oil and engine oil filter . X X Rotate tires. X X X X X Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X X X X Flush and replace engine coolant, if not done at 60 mos. X Check transfer ca[...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [150] Change engine oil and engine oil filter . X X X Rotate tires. X X XXXX Lubricate outer tie rod ends 2500/3500 (4X4) models only . X X XXXX Flush and replace engine coolant, if it[...]

Miles 1 12,500 120,000 127,500 135,000 142,500 150,000 (Kilometers) (181 000) (193 000) (205 000) (217 000) (229 000) (241 000) [Months] [90] [96] [102] [108] [1 14] [150] Inspect front wheel bearings. X X Inspect brake linings. X X Inspect and adjust parking brake if necessary . X X Adjust valve lash clearance. X Inspection and service should also[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 4 0 2 ▫ Prepar e For The Appointment ............ 4 0 2 ▫ Prepar e A List ........................ 4 0 2 ▫ Be Reasonable W ith Requests ............. 4 0 2 m If Y ou Need Assistance ................... 4 0 2 m W arra[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

The manufacturer has empower ed its dealers to make warranty and repair decisions that ensur e you are not inconvenienced. There is no need for you to wait for a decision from the manufactur er . If a special circumstance occurs that requir es information from the manufacturer , we have asked the dealer’s service management to make the contact on[...]

In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T [...]

Contract, and you requir e service after your manufactur- er’s new vehicle limited warranty expires, please r efer to your contract documents, and contact the person listed in those documents. W e appreciate that you have made a major investment when you purchased your new vehicle. Y our dealer has also made a major investment in facilities, tool[...]

406 IF YOU NEED CONSUMER ASSIST ANCE[...]

MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediatel[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Expr ess, and Discover orders ar e ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street addr ess is required when or dering manuals. (No P .O. Boxes). ?[...]

Call T oll Free at 1–800–890–4038 (U.S.) or 1–800–387–1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .daimlerchrysler .com or www .daimlerchrysler .ca/manuals IF YOU NEED CONSUMER ASSIST ANCE 409 9[...]

[...]

INDEX 10[...]

Air Cleaner , Engine ................... 331,358 Air Conditioner Maintenance ............... 3 3 8 Air Conditioning Refrigerant ............. 338,339 Air Conditioning System ................ 187,338 Air Conditioning System, Zone Control ........ 1 9 1 Air Filter .............................. 3 3 1 Air Pressur e, T ires .................... 252,259[...]

Body Mechanism Lubrication ............... 3 4 0 B-Pillar Location ........................ 2 4 7 Brake Fluid ............................ 3 8 1 Brake System ........................ 239,348 Anti-Lock ........................... 2 4 0 Disc Brakes .......................... 3 4 8 Fluid Check .......................... 3 4 8 Hoses ...................[...]

Child Seat ............................ 56,62 Cigar Lighter ........................... 1 2 7 Climate Control ......................... 1 8 5 Clock ................................ 1 5 1 Clutch Linkage Maintenance ................ 3 5 0 Compact Disc Maintenance ................. 1 8 4 Compact Disc Player .................. 158,164 Compact Spare T i[...]

Used Coolant ......................... 3 4 6 Door Ajar ............................. 1 4 5 Door Locks ............................. 1 6 Door Opener , Garage ..................... 1 2 0 Draining Fuel/W ater Separator Filter .......... 3 3 4 Drive Belts ............................ 3 3 1 Dual Rear Wheels ..................... 263,306 Electric Rear W [...]

Exterior Lighting ........................ 1 0 1 F a n .................................. 3 4 7 Filters Engine Oil ..................... 325,328,380 Flashers T urn Signal .......................... 1 0 3 Flat T ire Stowage ..................... 299,309 Fluid, Brake ........................... 3 8 1 Fluid Capacities ......................... 3 7 9 F[...]

Glass Cleaning .......................... 3 6 5 GVWR ............................... 2 6 9 Hands-Free Phone ........................ 7 9 Hazard W arning Flasher ................... 2 9 6 Head Restraints .......................... 9 3 Headlights .......................... 101,367 High Beam ........................... 1 0 4 High Beam/Low Beam Select [...]

Jack Location ........................... 2 9 8 Jack Operation .......................... 3 0 0 Jump Starting .......................... 3 1 0 Key , Replacement ........................ 1 2 Key , Sentry ............................. 1 1 Key-In Reminder ......................... 1 1 Keyless Entry System ...................... 2 2 Keys ..............[...]

Low W asher Fluid ..................... 1 4 9 Passing ............................. 1 0 4 Seat Belt Reminder ..................... 1 4 5 Service .............................. 3 6 7 Side Marker .......................... 3 7 8 T ransfer Case ......................... 2 3 0 T ransmission W arning ................ 150,281 T urn Signal ...............[...]

T railer T owing ...................... 79,279 Modifications/Alterations, V ehicle ............. 7 Mopar Parts ......................... 322,407 Multi-Function Control Lever ............... 1 0 3 New V ehicle Break-In Period ................ 6 7 Noise Control Maintenance .......................... 3 5 7 T ampering Prohibited ................... 3 5[...]

Passing Light ........................... 1 0 4 Pedals, Adjustable ....................... 1 0 8 Phone, Cellular .......................... 7 9 Phone, Hands-Free ....................... 7 9 Pickup Box ............................ 1 3 3 Placard, T ire and Loading Information ......... 2 4 7 Power Distribution Center ..................... 3 6 6 Door [...]

Remote Sound System Controls .............. 1 8 1 Replacement T ires ....................... 2 5 7 Reporting Safety Defects ................... 4 0 7 Restraint, Head .......................... 9 3 Restraints, Child ....................... 55,62 Rotation, T ires .......................... 2 6 1 Safety Checks Inside V ehicle ................. 7 0 Saf[...]

Shifting ............................... 2 1 8 Automatic T ransmission ................. 2 1 8 Manual T ransmission ................. 222,224 T ransfer Case ......................... 2 2 9 T ransfer Case, Shifting into T ransfer Case Neutral (N) .................. 286,288 T ransfer Case, Shifting out of T ransfer Case Neutral (N) ..................[...]

T ire Markings .......................... 2 4 3 T ire Safety Information .................... 2 4 3 T i r e s ............................... 70,251 Air Pressur e .......................... 2 5 1 Alignment ........................... 2 5 8 Chains .............................. 2 5 9 Changing ............................ 2 9 9 Compact Spare ........[...]

Mirrors ........................... 79,279 T i p s ................................ 2 8 0 T railer and T ongue W eight ................ 2 7 8 T railer T owing Guide ..................... 2 7 9 T railer W eight .......................... 2 7 9 T ransfer Case Fluid ............................... 3 8 1 T ransmission Automatic ........................[...]

Wheel Nut T orque .................... 305,308 W ind Buffeting .......................... 3 3 W indow Airbag .......................... 5 3 W indow Fogging ........................ 1 9 6 W indows .............................. 3 1 Power ............................... 3 1 Rear Sliding ........................... 3 2 W indshield Defroster ..........[...]