Eclipse - Fujitsu Ten cd5425 manual

OWNER'S MANUAL We appreciate your purchase of this receiver. Please read through this manual for correct operation. We suggest that after reading it you keep this manual in a safe place for future reference. ESN E5 High-Power "Full-Face" CD Receiver with MP3 Decoder CD5425[...]

2 For your safet y in using th e CD5425 W arnings and caution signs, illustrated bel ow , are posted throughout this manual as well as on the CD5425. They show safe and correct ways to handle the product so as to prevent personal injury to you, others and to avoid property damage. Before reading through the manual, take time to read through and lea[...]

3 Wa r n i n g ● Before drilling holes in a vehicle fo r inst allation, you must confirm the locations of pipes, t anks, electrical wiring, and other vehicle systems and compone nt s to ensure t hat there will be no interfer ence or contact. In additio n, you must also apply rus t prevention and leak prevention me asures at the drilling area. Oth[...]

4 Wa r n i n g ● Some equipment uses batteries. Never inst all equipment where young children can get access to batteries. If a battery is swallowe d, seek medi cal attention imm ediately . ● When ve hicle is moving , never take you r eyes off th e road to make adjustment s to the equipment. Y ou must p ay attention t o the road to avoid accide[...]

5 Cau tio n ● Wiring and inst alling this equipment require s expertise and experience. Professional inst allation is recommended. Consult with your dealer or a professional inst a ller . Incorrect wiring may damage the equipment or interfer e with safe vehicle operation. ● Use only the ac cessory parts as specified. Using o ther part s may cau[...]

6 Cau tio n ● A void hot surfaces when wiri ng equipment. High temperatures may damage wiring, causing short s, arcing and fires. ● When changing the inst allation location for this equipment, please consult the dealer where you bought it for safety reasons . Expertise is neces sary for r emoval and installation. ● Keep volume to a reasonable[...]

7 Cau tio n ● Do not short, disasse mble or heat the batteries, or place them in fire or water . Fire and injuries may result from battery rupt ure and leakage. ● Store the remote control in a place away from direct sunlight , high temperatures, and high moisture le vels. The case may change shape, an d the batt eries may r upture and leak. ●[...]

8 Table of Conten ts Operating pre cautions ............... ............. .................... ................... ...... 12 Notes on operation ............................................... .................................... ..................... 12 About compact discs . .................. ...................................... ................[...]

9 Other s ........ .... ...... ...... ..... ...... ...... ...... ..... ...... ...... .... ....... ...... ...... ..... ...... ...... .... ....... ...... .. 49 Adjustment of the front panel angle .............................. ...................................... .... 49 How to operate the CD player .......... ................... ............. ....[...]

10 How to operate the AR EA SHOT function (U.S.A. only) ............. ...... 70 About the AREA SHOT ................................................................................................. 70 To us e the A REA SHOT f unction .......... .... ...... ....... .... ...... ....... ...... .... ...... ....... .... .... 70 Reading the AREA S HOT da[...]

11 Switching between displays when receiving HD Radio............. .................................... 93 HD Radio rece ption setting s ....... ...... ..... ...... ...... ....... .... ...... ...... ..... ...... ...... ...... ..... ...... .. 93 How to oper ate the tune r with an op tional SI RIUS satell ite radio t uner connecte d (U.S.A . only) ..[...]

12 Operating pr ecautions Operating precautio ns <Y our CD5425 will perform well over a l ong period of time through correct handlin g and care.> Notes on oper ation ● For your safety , play only at volume levels that al low outside sounds to be heard. ● We recommend using with this player a disc with the logo shown to the left. ● Y ou [...]

13 Operat ing precautions About comp act discs ● The signal recorded on a compact disc is read by a laser beam, so nothing touches the disc surface. A scratch on the recorded surface or a badly warped disc may cause deteriorated sound quality or intermittent playback. Observe the following precautions to ensure high quality sound performance: ●[...]

14 Operating pr ecautions ● Y ou may notice that some brand new discs are rough around the center hole or outside edge. Remove the rough edges with the s ide of a ballpoint pen, etc. Rough edges may prevent proper loading in the deck. Flakes from the rough edges may also stick to the recorded surface and interfere with playback. ● Do not use ac[...]

15 Operat ing precautions ● Do not use a CD with glue or rem nants of adhesive tape or labels . They may cause the CD to get stuck inside or damage the dec k. ● When removing the ejected disc, pull it straight out along the slot. Pressing downward in the process may scratch the recorded surface of the disc. ● S pecially-shaped CDs, like heart[...]

16 Names of control s and parts Names of co ntrols and p art s Front view *: Double function butto n ➞ "MUTE" & "AREA SHOT" funct ions Never pl ace an object or rest your han ds or the like on the front pane l. [CD ] but ton Opens/closes front panel and eject s CD. [AUDIO CONTROL] but ton Adjusts volume and performs other [...]

17 ESN security ope rating pro cedure ESN security ope rating pro cedure About ESN This deck incorporates ESN (ECLIPS E Security Network). The ESN is a security system whic h disables all deck functions when the power is restored if the deck is stolen from the vehicle. Once the ESN is activated , removing power to the deck or vehicle will activate [...]

18 ESN security oper ating procedure How to operate the ES N (Key CD) securi ty How to program the Key CD Check t hat the un it is in st andby . Press and hold butto n [6], then the [F UNC] button, and hol d both fo r more tha n one second . A [SEC] message appears, in two seconds it will change to [DISC]. Pres s the [C D ] bu tton. The front panel[...]

19 ESN security ope rating pro cedure How to canc el the Key CD Check t hat the un it is in st andby . Press and hold butto n [6], then the [F UNC] button, and hol d both fo r more tha n one second . A [SEC] message appears, then in two seconds it will change to [DISC]. Pres s the [C D ] bu tton. The front panel opens; The CD5425 is now ready to yo[...]

20 ESN security oper ating procedure How to ch ange the Key C D First , cance l the exi sting Key CD. Refer to "How to cancel the key CD". Next, program a new Key CD. Refer to "How to program the Key CD". How to resume normal operation (ESN security lock out) If power is disconnected while ESN security is activ e (a Key CD was p[...]

21 ESN security ope rating pro cedure What happens if an inco rrect CD is ins erted? Af ter the 5th incorr ect at tempt, the di splay r eads [HEL P] for f ive seco nds. After the [HELP] mes sage will appear for five seconds, serial number will appear . Press the [C D ] butto n to clo se the fron t panel. Press button [6 ], then the [ FUNC] butt on,[...]

22 ESN security oper ating procedure How to turn the securi ty indicator on/off Once ESN s ecurity is ac tivated, the indic ator flashes whenever th e vehicle's igni tion switch is turned of f, warning potential thieves that the unit is protected. However , if d o not want this visible deterrent, i t may be turned off. With the un it in sta nd[...]

23 ESN security ope rating pro cedure How to read the Elect ronic Serial Num ber Check t hat the un it is in st andby . Press and hold button [4], then the [FUNC] butto n, and hold b oth for m ore than one secon d. [ESN] appears on the display , followed by an eight-digit number; this number is your elec tronic serial number (ESN). Y ou may us e th[...]

24 Basic operation Basic operatio n This section cov ers basic operating procedures. For additional det ails, please refer to the sections on specific functions . T urning the power on a nd off When the power is turned on, the state used when the power was turned off suc h as CD and tuner playback is restored. When th e vehicle has no AC C position[...]

25 Basic operatio n Listening to CD Pres s the [C D ] bu tton. The front panel opens. Inser t a CD int o the di sc slot, l abel sid e up. The CD will immediately start playing. When a CD is a lready loade d, pres s the [DIS C] button to swit ch to the CD mode. [DISC ] button [CD ] button CD5425.book 25 ページ ２００４年 １２月１１日?[...]

26 Basic operation Listening to the tuner Press the [FM AM] bu tton. This will turn the tuner on. Press the [FM AM ] button for le ss than on e second to switch to th e de sired FM or AM ba nds. Radio bands will switc h from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. T u rn the [SE L] button to the l ef t or ri ght to tu n[...]

27 Basic operation Adjusting audio volum e T u rn the [AUD IO CONTROL] b utton to the left or right. T urn to the right: Inc reases the volume. T urn to the left: Decreases the volume. Pre ss th e [MU TE ] but ton fo r le ss th an on e sec on d to c ut the vol ume or restore i t instantly . Do not adjust the volume or other cont rols while driving [...]

28 Basic operation Switching audio contr ol modes V arious audio control modes may be fine-tuned using this procedure. Press the [AUD IO CONTROL] bu tton for less than on e second to s elect the i tem t o be adjust ed. Modes will switc h in the order shown below each tim e the button is pressed. *1 : NON-F ADER output does not reflect BASS, MIDDLE,[...]

29 Basic operatio n MID (MIDDLE) Mode Adjusts mi ddle level. Mid mode can be adjusted for each source (CDP/CDC, FM and AM). T urn the [AUDIO CONTROL] button to the left or right. T urn to the right: Emphasizes medium sounds. T urn to the left: Softens medium sounds. TREB (TREBLE) Mode Adjusts treble l evel. T reble mode can be adjus ted for each so[...]

30 Basic operation SVC (Source V olume Control) Mode Y ou can set different volume levels for each audio mode. The volume for the initial FM mode (default value: 40) is us ed as a reference for storing the differences in volume that have been set for each audio mode. When SVC is set, the volume level can change as shown in the example settings in t[...]

31 Basic operatio n T urn the [AUDIO CONTROL] button to the left or right. T urn to the right: Increases the SVC setting value. T urn to the left: Decreases the SVC setting value. The volume dif ference can be set within a range of -10 to +20. LOUD Mode The loudness control may be turned on to emphasize low and high frequencies at low volume levels[...]

32 Basic operation Recording user prese t s for the equalizer The adjustment values for BAS S, MIDDLE and TREBLE settings made in the audio control mode c an be stored. The stored adjustment values can be called by changing the equalizer mode. For detai l, see "Changing the equalizer mode" on page 32. Press th e [AUDIO CONTROL] bu tton fo[...]

33 Basic operatio n How to operate the So und Adjustment Mod e About Sound Adjustment Mode The system has several features that allow you to adjust the acoustic characteristics i nside the cabin. In the Sound Adjustment Mode, th e following characteristics can be adjusted. Crossover The frequenc y band that is stored by audio m edia such a s CDs is[...]

34 Basic operation ● The crossover function is a filter that allocates specified frequency bands. ● A high-pass filter (HPF) is a filter that cut s out frequencies that are lower than the specified frequenc y (bass range) and allows higher frequencies (treble range) to pass through. ● A low-pass fi lter (LPF) is a filter that cuts out frequen[...]

35 Basic operatio n Making changes with Sound Adjustment Mode Press the [SOUND] bu tton for more than one second. The mode will change to sound adjustment mode . T u rn the [SE L] button to selec t a settin g item. When the button is turned, the setting item changes in the followin g order and selected item is highlighted. Press the [SEL ] butto n.[...]

36 Basic operation Disabling the Cross Over (F , R) function Front and rear speaker HPF (High Pass Filter) can be turned ON/ OFF . T u rn the [SE L] button to select ON or OFF . Press the [SEL ] butto n. The selected settings will t ake effect. Press the [RTN] button . At this time, other adjustments can also be made in sound adjustment mode. Press[...]

37 Basic operatio n Disabling the Cross Over (NF) fun ction Woofer (non-fader output) LPF (Low Pass Filter) can be turned ON/ OFF . T u rn the [SE L] button to select ON or OFF . Press the [SEL ] butto n. The selected settings will t ake effect. Press the [RTN] button . At this time, other adjustments can also be made in sound adjustment mode. Pres[...]

38 Basic operation Non-fad er phase s election (NO N-F Phase) The merging of sound between the front and rear speakers and the woofer can be improved by selecting the phas e. Switch the phas e to a phase which lets the speakers combine without any disharmony . T u rn the [SEL] b utton to select NO RMAL or REVER SE. NORMAL: Normal phas e REVERSE: Re[...]

39 Basic operatio n Making changes with Display Adjustme nt Mode This function allows adjustment of display contrast. Press the [D ISP] butto n for les s than one s econd. The display adjustment mode is activated. [DISP ] button CD5425.book 39 ページ ２００４年 １２月１１日　土曜 日　午後５時９分[...]

40 Basic operation Contrast adjustme nt Adjust the display contrast to the bes t level in accordance with th e angle of viewing. Press the [SEL ] butto n. Enters contrast adjustment mode. T urn the [S EL] but ton to ad just co ntrast . When the button is turned, the contrast level changes in the following order . Press the [SEL ] butto n. The selec[...]

41 Basic operatio n Making changes with Function Mode A variety of settings can be changed. Press the [FUNC] bu tton for l ess than one secon d. The function mode is activated. T u rn the [SEL ] butto n in eithe r directio n to disp lay setti ng ite ms for se lecti on. When the button is turned, the setting item changes in the followin g order . *1[...]

42 Basic operation Disabling the guide tone feature (for button operation) The receiver is set at the factory to emit a beep tone in response to button operation. The guide t one feature may be disabled in th e following procedure: T u rn the [SE L] button to select GU IDE TONE. Press the [SEL ] butto n. The Guide T one Mode will be switched ON/OFF[...]

43 Basic operatio n Clock display on/off Switches the clock display to ON/OFF . T u rn the [SE L] button to select C LOCK DISP . Press the [SEL ] butto n. The clock display ON/OFF mode is activated. T u rn the [SE L] button to select ON or OFF . Press the [SEL ] butto n. The selected settings will t ake effect. Press the [RTN] button . At this time[...]

44 Basic operation Setting the time This receiver uses the 12-hour display notation. T u rn the [SE L] button to select C LOCK ADJ. Press the [SEL ] butto n. The clock adjustment mode is activated. Pres s the [SE L] button t o displa y the ite m to be sele cted fo r adju stment. Hours or minutes will be switched each time the button is pressed. T u[...]

45 Basic operatio n Setting the steering switch function (U .S.A. only) The vehicle’s factory loaded steering switch becomes inoperabl e when the CD5425 is inst alled. The ECLIPSE website (E-iSER V) provides software that enables steering switch operation even wit h the install ation of the deck. Import this software into your CD5425. Depending o[...]

46 Basic operation Reading steering switch d at a The steering switch dat a that has been downloa d from E-iSERV (website) to a CD-R can be loaded into the deck and saved there. Press the [FUNC] bu tton for l ess than one secon d. The function mode is activated. T u rn the [SE L] button to select STEER S W . Press the [SEL ] butto n. [INSER T DISC][...]

47 Basic operatio n Press the [RTN] button . At this time, other adjustment s can also be made in function mode. Press the [FUNC] or [RTN] but ton to exit function mode. During S tep , the function mode can also be cancelled by pressing the [FUNC] button. ● The deck can only import file from CD-Rs that have been written in ro ot di rect ories . ?[...]

48 Basic operation Compatibility with various switches Displays the comp atibility of the system’s m odes and the steering switch . *1 : Switch names chan ge dependin g on vehicle make and model. *2 : If a SIRIUS satellite r adio tuner ( purchased sep a rately) is con nected, categories can be switched when in the satellite mode. Switc h name *1 [...]

49 Basic operatio n Others Adjustment of the front p anel angle Display angle can be adjus ted. Push an d hold the [TIL T ] button with the display comple tely close d. While pushing the [TIL T] button, the display will gradually open. When t he disp lay has opened to the d esire d ang le, releas e the [TI L T ] button. Pressing the [TIL T] button [...]

50 How to operate the CD player How to op erate the CD player First press the [DISC] button for les s than one second to switch to the di sc mode. It is assumed here that a CD has already been loaded into the unit. Listening to CDs Pres s the [DISC] bu tton for less than one s econd to switch to the CD pla yer mode. This start s CD play . If an ext[...]

51 How to oper ate the CD player Advancing to the next track or returning to the beginning of t he track being played T u rn the [SE L] button to th e left or right. T urn to the right: Advances to the next track. T urn to the left: Returns to the beginning of the track b eing played. (Repeat turning for previous tracks.) Fast Forward/Rewind Fast f[...]

52 How to operate the CD player Repeating the same t rack (REPEA T) Press th e [5 RPT] button to repe at the trac k being played . T o cancel, press the [5 RPT] button again. Playing tracks in ra ndom order (RANDO M) Press the [6 RAND] button to play the tra cks in random order . T o cancel, press the [6 RAND] button again. ● Duri ng ra ndom pl a[...]

53 How to oper ate the CD player Ejecting the disc Pres s the [C D ] bu tton. The front panel opens and the dis c is ejected. Remove t he disc and pres s the [CD ] bu tton. The front panel closes. If lef t alone for 15 seconds af ter the disc ejection, the front p anel closes af ter the BEEP sound. ● Do n ot dri ve with the fr ont pan el open. Th[...]

54 How to operate the CD player Displaying CD TEXT Only the built-in CD player support s CD TEXT . It can not be displayed wit h the optional CD changer . If the CD came with a logo shown below , it is recorded with a disc title and track titl es. These information will be displayed during playback. Pres s the [DISP] butto n for more than on e seco[...]

55 How to operat e the MP3 player How to op erate the MP3 player About MP 3 What is M P3? MP3 (MPEG Audio Layer III) is a standard format for audio compression technology . By using MP3, a file can be compressed to one-tenth the size of the original. This deck has limit ations on MP3 file st andards and recorded media and formats that can be used. [...]

56 How to operate the MP3 player Media Media capable of play ing MP 3 includes CD-R and CD-RW discs. Compared to CD-ROM media commonly used for music discs, CD- R and CD-RW discs are fragile in high temperature/high humi dity environments and one section of the CD-R and CD-RW may become incap able of playback. Fingerprints or scratches on the disc [...]

57 How to operat e the MP3 player File names Only files with the MP 3 file extension ".mp3" can be rec ognized as MP3 and played. Be sure to save MP3 files with the ".mp3" fi le extension. The "MP " letters of the file extension will be recognized w hether entered as u ppercase lette rs or lowercas e letters. Multi-se [...]

58 How to operate the MP3 player Listening to M P3 file Pres s the [DISC] bu tton for less than one s econd to switch to the CD pla yer mode. This start s MP3 file play . If an external CD changer is connected, each additional press of the [DISC] button will switch modes from CD changer 1 ➔ CD changer 2 ➔ CD player . A changer or player with no[...]

59 How to operat e the MP3 player Advancing to the next track (file) or retu rning to the beginning of t he track (file) being playe d T u rn the [SE L] button to th e left or right. T urn to the right: Advances to the next track (file). T urn to the left: Returns to the beginning of the track (file) being played. Repeat turning for previous tracks[...]

60 How to operate the MP3 player Playing the beginning of files (SCAN) Press the [4 SCAN] button. Press the button briefly to play just the first 10 seconds of each song for all the files in the same lay er of the folder being played. Pressing the button until [FOLD SCAN] is dis played will play just the first 10 seconds of the first song in each f[...]

61 How to operat e the MP3 player Playing files in rand om order (RANDOM) Press the [6 RAND] button. Press the button briefly to randoml y play the files in the same layer as the folder being played. Pressing the button until [ALL RAND] is dis played will randomly play the files in all the folders. T o cancel, press the [6 RAND] button again. Displ[...]

62 How to operate the tuner How to op erate the tuner First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting sta tions in memory . The receiver will accept up to 24 st ations in memory: 6 in AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting) T uni ng to a station Press the [FM AM ][...]

63 How to operate the tuner Entering stations into memory automatically (The automatic prese t mode: ASM) Press the [FM AM ] button for le ss than on e second to switch to th e de sired FM or AM ba nds. Radio bands will switc h from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button is pressed. Press th e [SEL] but ton for more than two se co[...]

64 How to operate the tuner Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. Press the [FM AM ] button for le ss than on e second to switch betwee n FM and A M. T u rn the [S EL] butto n to the right or left to tune to the st atio n to be en tered in memor y . Selec t any button[...]

65 How to operate the tuner Preset station scan This function enables reception of all the st ations in the preset buttons for five seconds each. Press the [SEL ] button for less than two seconds . [P SCAN] will appear on the display , and stations stored under preset buttons [1] through [6] will be played for five seconds each. T o stop th e prese[...]

66 How to operate the tuner Changing the receptio n sensitivity for a utomatic scanning The deck let s you select the reception sensitivity to be us ed for automatic scanning of st ations. The two sensitivity modes available for this deck are AUT O mode and DX mode. Check t hat the de ck is in st andby mod e. Press and h old butto n [1], th en the [...]

67 How to operate the tuner Changing the radio ba nd location The location for the radio bands used between th e North American regio n and the Asia/A ustralia/Latin region can be switched. The default setting is USA (North America). Check t hat the de ck is in st andby mod e. Press and h old butto n [3], th en the [F M AM] b utton, and hold b oth [...]

68 How to operate the tuner FM reception charact eristics In general, FM has much better tonal quality than AM. However , FM and FM stereo reception encounter several characteristic problems not enc ountered with AM. FM is more difficult to receiv e than AM in a moving vehicle. The following are explanatory notes on what to ex pect from FM receptio[...]

69 How to operate the tuner Reception area of FM broadc ast s A home receiver can catch weak FM stereo s ignals through the use of a tall, directional or ultra-sensitiv e antenna. In a moving vehicle, the area for good reception is lim ited because of varying conditions encountered while driving, including the types and height s of broadcast antenn[...]

70 How to operate the AREA SHOT function (U.S.A. only) How to operate th e AREA SHOT function (U.S.A. only) About the AREA SHOT With the AREA SHOT function, road information such as the direction of travel and the street names of turn intersections can be downloaded from the ECLIPSE website (E-iSERV ), imported into the CD5425, and shown on the dis[...]

71 How to operate the AREA SHOT function (U.S .A. only) Reading the AREA SHO T dat a The Area Shot data that has been downloaded from E-iSER V (web s ite) to a CD-R can be loaded into the deck and saved there. Press the [FUNC] bu tton for l ess than one secon d. The function mode is activated. T u rn the [SE L] button to select A REA SHOT . Press t[...]

72 How to operate the AREA SHOT function (U.S.A. only) Press the [SEL ] butto n. The selected file will be saved. While the files are being read [READING ...] will appear . When re ading has finished, [COMP LETED] will appear on the display and then it will return to the disp lay for selecting the func tion mode. ● The deck can only import file f[...]

73 How to operate the AREA SHOT function (U.S .A. only) Changing the AREA SH OT mode Press the [MU TE] button for more than o ne seco nd. The AREA SHOT mode is acti vated. Information such as intersection street names and the direction of turns are displayed in text and with arrows. Pressing and holding the [MUTE] button a second ti me, closes the [...]

74 How to operate the AREA SHOT function (U.S.A. only) Using the AREA SHOT mode By manually switching between guidanc e points, both previous and next guidance point s can be confirmed during guidance. Intersec tion street names and the direction of turns are shown on the di splay in text and with arrows. Switching between guida nce point s After p[...]

75 How to operate the AREA SHOT function (U.S .A. only) Display A rrows Arrows for indicating turn directions are displayed as foll ows. Depending on driving conditions, arrows indicate the foll owing: Diagon ally forward right Diagon ally left re ar Right Left Diagon ally rear right Diagon ally for ward left Expres sway Interse ction Tr a ff i c m[...]

76 How to use an op tional remote contr ol How to use an optional remote control Precaution s in use of the remote con trol ● Be careful when handling the remote control, especially because it is small and light. Dropping or striking i t hard may damage it, wear out the battery or cause a malfunction. ● Keep the remote control free of moisture,[...]

77 How to use an optional remote control T urn ing the power on/o ff When the power is turned on, the state used when the power was turned off such as CD and tuner play ing is restored. Press the [PWR ] butto n. The power turns on or off each time the button is pressed . Adjusting the audio vo lume Pres s the [ ] or [ ] button. [ ] button:Increases[...]

78 How to use an op tional remote contr ol Switching playback modes Press the [MOD E] button . Press the button to switch modes in the following sequence: How to play the tuner Select the tuner mode first. Selecting the FM/AM band Press the [BAND] or [TU] bu tton. Each p res s wil l sw itc h tu ner mo des f rom FM1 ➔ FM2 ➔ FM3 ➔ AM. Mode s ca[...]

79 How to use an optional remote control Selecting a st ation (ma nually or automatically) A short press of the button wil l allow manual st ation tuning. Pressing for more than one second will start automatic tuni ng. Press the [ T UNE•SEE K ] butto n. [ ] button: T unes to higher frequency stations. [ ] button: T unes to lower frequency station[...]

80 How to use an op tional remote contr ol Advancing to the next track or returni ng to the beginning of the track being played Press the [ TRACK ] button. [ ] button: Advances to the next track. [ ] button: Returns to the beginning of the track b eing played. (Press repeatedly to move to previous tracks.) Skipping to the next or prev ious disc Pre[...]

81 How to use an optional remote control How to play MP3 Switching disc modes Press the [D ISC] butto n. The disc mode is activated. Press the [BAND] or [DISC] bu tton. When one or two CD changers are connected, press the [BAND] or [DISC] button to change modes from CD player ➔ CD changer 1 ➔ CD changer 2. The indicator will skip a changer or p[...]

82 How to use an op tional remote contr ol Replacing the battery Use two AAA size batteries. Remove t he back cover of the remot e contro l unit by gentl y pres sing and sl iding it in the di rect ion indica ted by th e arr ow . Inst all the t wo batt eries provi ded into the c omp artm ent as il lustrat ed insi de the co mp artm ent. Return the ba[...]

83 How to use an optional remote control ● Be extremely careful not to swallow the battery . ● The ba tter y lif e is ap proxim atel y one y ear . If t he remo te con trol unit does not operat e cor rect ly o r if the bu tto n lamp get s di m, repl ace th e bat teri es. ● Be su re to orie nt t he bat ter ies c orrec tly so tha t the posi tive[...]

84 How to operate the receiver wi th an optional C D changer connected How to op erate the receiver with an optional CD ch anger connect ed This section covers the operation of an optional CD changer that is connected to the receiv er . T o switch from another mode, press the [DISC] button for less than one second. Listening to a CD Press the [DI S[...]

85 How to opera te the receiver w ith an optional CD changer connecte d Playing the beginning of tracks (SCAN) Press the [4 SCAN] button. Pressing the button for less than one second causes the changer to move up to the next track and play it for 10 seconds, then move up to the next track and play it for 10 seconds, and so on, on one CD, until the [...]

86 How to operate the receiver wi th an optional C D changer connected Playing tracks in ra ndom order (RANDO M) Press the [6 RAND] button. Pressing on the button for less than one sec ond causes the changer to play the tracks on the c urrently playing CD in random order , until the button is pressed again. Hold the button until the [ALL RAND] di s[...]

87 How to opera te the receiver w ith an optional CD changer connecte d Specifying a CD to play A CD of your choice is directly select able out of the loaded discs. Press the [SEL ] butto n for less than on e secon d. Press a bu tton from [1] to [6]. T o s elect a CD from nos. 7 to 12, pres s the desired button considerably longer . B u t t o n s 1[...]

88 How to operate the tuner wit h an optional HD R adio tuner con nected (U.S.A . only) How to op erate the tun er with an op tional HD Rad io tuner c onnected (U.S.A. on ly) About HD Radio If the optional HD Radio (High Definiti on Radio) tuner unit is c onnected, terrestrial digital broadcast s can be received. When terrestrial digital broa dcast[...]

89 How to opera te the tuner wi th an optional HD Radio tuner connected (U.S.A . only) First, press the [FM AM] button to start tuner operation. There are automatic and manual methods for setting sta tions in memory . The receiver will accept up to 24 st ations in memory: 6 in AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting) T uni n[...]

90 How to operate the tuner wit h an optional HD R adio tuner con nected (U.S.A . only) Entering stations into memory automatically (The automatic prese t mode: ASM) Press the [FM AM ] button for le ss than on e second to switch to th e de sired FM or AM ba nds. Radio bands will switc h from FM1 ➔ FM2 ➔ FM3 ➔ AM in order each time the button [...]

91 How to opera te the tuner wi th an optional HD Radio tuner connected (U.S.A . only) Manually setting stations into memory This section covers the setting of stations in memory under the numbered buttons. Press the [FM AM ] button for le ss than on e second to switch betwee n FM and A M. T u rn the [S EL] butto n to the right or left to tune to t[...]

92 How to operate the tuner wit h an optional HD R adio tuner con nected (U.S.A . only) Preset station scan This function enables reception of all the st ations in the preset buttons for five seconds each. Press the [SEL ] button for less than two seconds . [P SCAN] will appear on the display , and stations stored under preset buttons [1] through [[...]

93 How to opera te the tuner wi th an optional HD Radio tuner connected (U.S.A . only) Switching between di splays when rec eiving HD Radio During digital reception, the name of the station being received and other information can be display ed. Pres s the [DISP] butto n for more than on e second . Each time the button is pressed the display item c[...]

94 How to operate the tuner wit h an optional HD R adio tuner con nected (U.S.A . only) T u rn the [SE L] button to selec t AUTO or OFF . In the [AUT O] setting, the selecti on is switched between digital an d analog reception autom atically . In areas where digital reception is not possible, reception is automatically switched to analog to avoid l[...]

95 How to operate th e tuner with an opt ional SIRIUS satellite radio tuner connected (U.S.A. only) How to operate the tuner with an optional SIRIUS satelli te radio tuner connect ed (U.S.A. onl y) About SIRIUS satellite radio If the optional SIRIUS satellite radio tuner unit is connected, satellite radio broadcast can be received. With SIRIUS sate[...]

96 How to operate the tuner with an o ptional SIRIUS satellite radio tuner connected ( U.S.A. only) The receiver will accept up to 24 st ations in memory . Selecting the radio m ode Press the [FM AM] bu tton for m ore than one sec ond. The mode switches between satellite radio mode and FM/AM radio mode each time the button is pressed. Selecting a c[...]

97 How to operate th e tuner with an opt ional SIRIUS satellite radio tuner connected (U.S.A. only) Category selection The ch annel can be sel ected f rom a mong c ateg ori es such as POP and ROCK. Consult the SIRIUS website for detai ls of categories. Press the [ ] or [ ] button fo r more th an one second. Categories will switch in order shown bel[...]

98 How to operate the tuner with an o ptional SIRIUS satellite radio tuner connected ( U.S.A. only) Manually setting chan nels into memory This section covers the setting of c hannels in memory under the numbered buttons. T u rn the [S EL] butto n to the right or left to tune to the channe l to be ent ered in memory . Selec t any button, from [1] t[...]

99 How to operate th e tuner with an opt ional SIRIUS satellite radio tuner connected (U.S.A. only) Preset channel sca n This function enables reception of all the channels in the preset buttons for five seconds each. Press the [SEL ] button for less than two seconds . [P SCAN] will appear at the display , and channels stored under preset buttons [[...]

100 Others Others Connecting po rt able au dio players (to the AUX jack) Use a commonly availabl e accessory cord. With a jack for AUX cord (sold separately ), portable audio pl ayers and other external input s can be connected to the system. T u rn on the portable au dio play er and start it s pla y functio n. Switch to AUX mod e by pres sing the [...]

101 Others Changing auxiliary input sensitivity The sensitivity of the auxi liary mode can be changed. Press the [FUNC] bu tton for l ess than one secon d. THe function mode is activated. T u rn the [SE L] button to sel ect AUX S ensitivity . The selected item is highlighted. Press the [SEL ] butto n. The AUX sensitivity mode is activ ated. T urn t[...]

102 Others User Registration Key display User R egistration Key is your CD 5425's unique ID. In order to use the ECLIPSE websi te ( E-iSERV), a 16-digi t User Regist rat ion Key is necessa ry . Check t hat the de ck is in st andby mod e. Pres s the [DISP] butto n for more than on e second . The first 8 digit s of your User Registration Key wil[...]

103 If you have a questi on: If you hav e a question: First check the items mentioned below before attempting to troubleshoot problems. If a prob lem occur s, for ins tance when t he unit do es not res pond to any but ton pres ses, or the d isplay d oesn't w ork corr ectly , p ress th e [RESET] button using a paper clip or similar item. Pressi[...]

104 If you have a questi on: Displayed information (for troubleshootin g) The information li sted in the chart below is di splayed to show the st atus of the CD, AREA S HOT function, CD changer and SIRIUS satellite radi o tunner . Refer to the chart for the appropriate action. Information Contents Explanation and remedial action to take INFO 2 NO D[...]

105 If you have a questi on: Mode Probl em Causes Remedial action to t ake Refer to page Common to all Dead or weak sound Is the volume control up sufficiently? Turn up the volume control. 27 Is the muting function i n effect (MUTE)? Cancel the muting (MUTE) function. 27 Is the fader or balance control set far to one side? Readjust the fader and ba[...]

106 If you have a questi on: Mode Problem Causes Remedial action to take Refer to pa ge CD The d isc ca nnot be in sert ed. The disc is ejected as soon as it is inserted. Or , th e disc cannot be eject ed. The disc cannot be changed. Is an extra label or seal applied to the disc? Do not apply labels or seals to the disc. 13 Are there rough edges, d[...]

107 Specifications Specifications <GENERAL> <FM TUNER> <AM TUNER> <CD SECTION> Power Suppl y 14.4V DC (1 1-16V) Current Drain 3A Dimensions (W x H x D) In-Das h Unit 7" x 2" x 6-1/8 " (178 x 50 x 155mm) Mass (weig ht) Approx. 1.4kg Usage te mperat ure range -20°C to + 65°C (-4°F to +149°F ) S torage tempe [...]

108 Specifications <AUDIO AMPLIFIER> Power Output 14W x 4 (20Hz~20 kHz, 1 % THD, 4 Ω , Vcc=14.4V) Max. 50W x 4 Output Level/Im pedance 5V/55 Ω line-out i mpedance T o ne Ac tion Bass: ±12dB at 80H z Middle : ±12dB at 630Hz T reble : ±12dB at 10kHz Loudness +10dB a t 100Hz/+6. 5dB at 10k Hz CD5425.book 108 ページ ２００４年 １?[...]

109 Before installation Before inst allatio n Components Inst allation angle In order to maint ain proper functioning, i nstall the unit within an angle of 3 0 degrees from horizont al (standard). If this is not done, sound skippi ng or ejection of the CD may occur . ● Note ● Be sure to disconnect the vehicle battery's negative terminal be[...]

110 Mounting instr uction Mountin g instruction Mounting the main unit –If inst alling the main unit by the mounting s leeve– Inser t the mo untin g sleev e into the o pening i n the vehi cle dash board or c onsol e box. Use a scr ewdrive r or the l ike to be nd the t abs in the mount ing sleeve t o secur e the mount ing sl eeve. Att ach the si[...]

111 Mounting instructio n Mount the stu d bol t to the main u nit. Insert t he main un it into the mounti ng sl eeve unti l it locks in place. Fasten the re ar of the ma in uni t using eith er meth od [A ] or [B]. Some automobiles m ay be equipped to secure the bac k of the main unit using the stud bolt and suppli ed rubber support. Select method [[...]

112 Mounting instr uction –If inst alling the main unit by the side bracket s of the vehicle– Remove t he pocke t s and any ot her acces sorie s from t he cente r cluster to make room fo r the ma in unit . Remove th e mounti ng side br acket s for the poc ket. Attach the si de b rackets to the m ain un it. Install the m ain un it in the vehicle[...]

113 Mounting instructio n Names of lead wires and destinations (refer to Page 1 15) ● Caution ● Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. ● Note ● T o prev ent unconnected leads from shorting out, insulate them by wrapping their tips with electrical t ape. Similarly , insulate the ends[...]

114 Mounting instr uction System CD5425 CD5425 CD5425 HDR105 HD RADIO TUNER CD CHANGER CD5425 21010 CD5425 MP3 PLA YER, MD PLA YER, etc. EXTERNAL PRODUCT Note: Adjust th e extern al amp lifier’s input lev el. CD5425.book 114 ページ ２００４年 １２月１１日　土曜 日　午後５時９分[...]

115 Mounting instruction 1) CD54 25 Recei ver , use d alone Caution Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. NON-F ADER 10 FRONT 8 7 REAR 9 TO BA TTERY+12V (Permanent supply) TO POWER ANTENNA RELA Y (supply) TO HEAD LIGHT SWITCH (supply) TO TURN-ON LEAD OF EACH UNIT (supply) Red Y ellow Blue [...]

116 Mounting i nstruction 2) CD5425 + CH3083 + CH3083 + Power Amplif ier Caution Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. Note 1. The switch on the back side of CD changer (A) must be set the "L" position. 2. The switch on the back side of CD changer (B) must be set the "H"[...]

117 Mounting instruction 3) CD5425 + H DR105 + CH3083 + Power Ampli fier Caution Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. TO POWER ANTENNA RELA Y (supply) TO HEAD LIGHT SWITCH (supply) TO TURN ON LEAD OF EACH UNIT (supply) TO ACC (Power supply) 1 TO BA TTERY+12V (Permanent supply) TO BA TTERY[...]

118 Mounting i nstruction 4) CD5425 + CH3083 + 21010 + Power Amplifi er Caution Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. TO POWER ANTENNA RELA Y (supply) TO ACC (Power Supply) 1 TO BA TTERY+12V (Permanent supply) 2 TO GROUND Brown Brown/Black Purple/Black ( - ) Black Purple (+) Green/Black ( [...]

119 Mounting instruction 5) CD5425 + E XTERNAL PR ODUCT (MP3 PLA Y ER, MD PLA YE R, etc) Caution Never connect the power supply to the speaker leads, otherwise it causes damage to the main unit. TO BA TTERY+12V (Permanent supply) 2 TO POWER ANTENNA RELA Y (Supply) TO HEAD LIGHT SWITCH (Supply) TO TURN ON LEAD OF EACH UNIT (Supply) TO ACC (Power sup[...]

120 How to contact customer service How to cont act custom er service Should the product require s ervice, please cont act your nearest Eclipse dealer . <U.S.A/CANADA> DIVISION OF FUJITSU TEN CORP . OF AMERICA 19600 SOUTH VERMONT A VENUE, TORRANCE, CA 90502 Phone: (310) 327-2151 <AUSTRALIA> FUJI TSU TEN ( AUS TRALI A) P TY L TD. ECLIPSE[...]

121 How to contact custome r service <KOREA> T ranspectra Co., Ltd. 1 15- 16 nonhyun dong kangnam ku Seoul, Korea. Phone: 02-540-4595 Fax: 02-2-540-4666 HYUNDAI AUTONET Co., L TD. 1st FL. Namhyoung Bldg, 746-23 Y eoksam-Dong, Kangnam-Ku, Seoul, Korea 135-080 Phone: 02-508-6001 Fax: 02-2-508-6067 <T A IW AN> Sentrek T aiwan, L TD. 1, 9F [...]

•••••••••••••••••••••••••••••••••••••••••••••••••••• Memo 122 CD5425.book 122 ページ ２００４年 １２月１１日　土曜 日　午後５時９分[...]

123 IMPOR T ANT RECORD YOUR “KEY CD” HERE… ST ORE YOUR “KEY CD” ALONG WITH YOUR OWNER’S MANUAL TAKE THIS OUT. CD5425.book 123 ページ ２００４年 １２月１１日　土曜 日　午後５時９分[...]

www .eclipse-web.com FUJITSU TEN LIMITED Contact:FUJITSU TEN CORP. OF AMERICA 19600 So. Vermont Avenue, Torrance, CA 90502 Call:800-233-ECLIPSE "ECLIPSE" is a registered trademark of FUJITSU TEN LIMITED in 48 countries including the U.S. and Japan. 090001-14700700 0412 (F.O) CUSTOMER NOTICE Please retain this booklet and write in the seri[...]