Ford 2007 E-150 manual

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 16 Entertainment Systems 19 AM/FM stereo 19 AM/FM stereo with single CD 21 AM/FM stereo with in-dash six CD 25 Climate Controls 31 Heater only 31 Manual heating and air conditioning 32 Lights 34 Headlamps 34 T urn signal control 38 Bulb replacement 39 Driver Controls 44 W ind[...]

Tires, Wheels and Loading 102 T ire information 104 T ire inflation 106 V ehicle loading 122 T railer towing 128 Recreational towing 139 Driving 140 Starting 140 Brakes 143 T raction Control™/AdvanceT rac 威 145 T ransmission operation 151 Roadside Emergencies 163 Getting roadside assistance 163 Hazard flasher switch 165 Fuel pump shut-off switc[...]

Maintenance and Specifications 207 Engine compartment 209 Engine oil 211 Battery 214 Engine coolant 216 Fuel information 222 Air filter(s) 237 Part numbers 239 Maintenance product specifications and capacities 241 Engine data 247 Accessories 251 Index 253 All rights reserved. Reproduction by any means, electronic or mechanical including photocopyin[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

Fuel pump shut-off switch: In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). T o reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter . SAFETY AND ENVIRONMENT PROTECTI[...]

SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide. Service Data Recording Service data recorders in your vehicle are capable of collecting and s[...]

V ehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’ s W arranty Guide for more information. Some vehicles are equipped with Powertrain Control Systems that can detect[...]

Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete V ehicle Manual, Ford T ruck Body Builder’ s Layout Book and the Qualified V ehicle Modifiers (QVM) Guidelines a[...]

Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfuncti[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Electronic throttle control: Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opp[...]

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by your authorized dealer . Normal braking is still functional unless the brake warning light also is illuminated. Airbag readiness: If this light fails to illuminate when ignition is turned to ON, [...]

AdvanceT rac 威 (if equipped): Flashes (two times per second) when the AdvanceT rac 威 with RSC system is active. If the light remains on, or ⬙ SERVICE RSC NOW ⬙ is displayed in the odometer display with a chime, have the system serviced immediately by your authorized dealer . (Flashes one time every two seconds when AdvanceT rac 威 with RSC[...]

Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster , check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turne[...]

Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine a[...]

T achometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Battery voltage gauge: Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s ele[...]

AUDIO SYSTEMS AM/FM stereo (if equipped) 1. Seek: Press / to find the next listenable station down/up the frequency band. 2. T une: Press / to manually adjust the radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: T o set a station: Select frequency band AM/FM1/FM2; tune to a station, press [...]

5. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 6. T one: Press TONE until the desired level — Bass, T reble, Fade appears on the display . T urn the volume control to raise/lower the levels, or to move the audio sound from the right to left or the front to back (if equipped). 7. CLK (Clock): T o set the hour , [...]

Satellite Compatible AM/FM Stereo In-Dash Single CD/MP3 Radio (if equipped) 1. SEEK: Press and release SEEK / for previous/next strong station or track. 2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display , its corresp[...]

3. AUX: This function is not operational. 4. MUTE: Press to MUTE playing media; press again to return to playing media. 5. EJ: Press to eject a CD. 6. Bass: Press BASS; then press SEL / to decrease/increase the bass output. T reble: Press TREB; then press SEL / to decrease/increase the treble output. 7. Select: Use with Bass, T reble, Balance, Fade[...]

Folder/T rack mode: In MP3 mode, press MENU until MODE appears in the display . Use SEL to toggle between FOLDER (only tracks within selected folder are accessible) or TRACK (all tracks on disc are accessible) MODE. 10. REPEA T : Repeats the current CD/MP3 track when active (ON). Press to show repeat status. Press again to toggle status. 11. SHUFFL[...]

19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. CD: Press to enter CD mode. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD player[...]

Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3 Radio (if equipped) 1. SEEK: Press and release SEEK / for previous/next strong station or track. 2. TEXT : The filename (Fi), song title (So), artist text (Ar) or album text (AL) may be viewed while playing an MP3 selection. When MP3 selection text is shown on the message display , its co[...]

3. AUX: Press to toggle between the current playing media and DVD (if equipped). 4. MUTE: Press to MUTE playing media; press again to return to playing media 5. EJ: Press to eject a CD. Press EJ and a memory preset to eject a specific disc. Press and hold to eject all loaded discs. 6. Bass: Press BASS; then press SEL / to decrease/increase the bass[...]

AM/FM1/FM2. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use SEL to manually increase ( ) or decrease ( ) the hours/[...]

18. Memory presets: T o set a station: Select frequency , tune to a station, press and hold a preset button until sound returns. 19. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 20. Load: Press to load a CD. Press LOAD and a memory preset to load to a specific disc slot. Press and hold to load up to six discs. 21.[...]

For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www .siriusradio.com 24. CD slot: Insert a CD, label side up. Accessory delay W ith accessory delay , the window switches, moon roof (if equipped) and audio system may be used for up to ten minutes after the ignition [...]

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Dirty , warped or damaged CDs, irregular shaped CDs, CDs with a scratch protection film attached, and CDs with ho[...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. VENT : Distributes[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each con[...]

T o aid in side window defogging/demisting in cold weather: 1. Select MIX. 2. Set the temperature control to maintain comfort. 3. Set the fan speed to HI. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR FAN SPEED ADJUSTMENT (IF EQUIPPED) The rear fan controls adjust the[...]

HEADLAMP CONTROL • The first position turns on the parking, tail, license plate and side marker lamps. • The outer position turns on the headlamps. Battery saver The battery saver can be set to turn off the courtesy lamps within 2 or 10 minutes if a door is left open and the key is not in the ignition. Demand (manually switched on) interior lam[...]

Daytime running lamps (DRL) (if equipped) T urns the headlamps on with a reduced output. T o activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or parking lamp position. Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activat[...]

P ANEL DIMMER CONTROL T o adjust the brightness of the instrument panel, rotate the dimmer control clockwise/counterclockwise when the headlamp control is in the parking lamp or low-beam position. T o turn on the interior lamps, rotate the dimmer control fully counterclockwise past the detent. The dome lamp will not illuminate if the control switch[...]

3. T urn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it. 5. • Aerodynamic: Locate the verti[...]

8. • Aerodynamic: Locate the horizontal adjuster (1) for each headlamp. T urn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment. • Sealed beam: Locate the horizontal adjuster (2) for each headlamp. T urn it clockwise or counterclockwise,[...]

Third row courtesy/reading/cargo lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully counterclockwise or when any door is opened. W ith the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control. Front and rear courtesy/reading lamps The[...]

Function Number of bulbs T rade number Headlamps (sealed beam) 2 H5054 Headlamps (aerodynamic) 2 9007 Park lamp and turn signal (front) 2 4157K or 3157K Back-up lamps 2 3156K or 3156 License plate lamp 1 168 Stop/tail/turn/side marker lamp 2 3457K or 3357K High-mount brakelamp 2 912 Cargo lamp 1 211-2 Dome lamp (standard) 1 912 Map/reading lamp 2 2[...]

4. Remove the bulb retaining ring by rotating it counterclockwise, and slide the ring off the plastic base. 5. Pull the bulb straight out. Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next tim[...]

3. Remove the four headlamp bulb retaining screws and the retaining ring. 4. Remove the headlamp. 5. Disconnect the electrical connector from the bulb and remove the bulb. T o install the new bulb, follow the removal procedures in reverse order . Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the OFF position[...]

Replacing license plate lamp bulbs 1. T urn the headlamp switch to OFF and then remove the two screws and the license plate lamp assembly from the rear door . 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb. T o install the new bulb, follow the removal procedures in rev[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

TILT STEERING WHEEL T o adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. ILLUMI[...]

Storage compartment (if equipped) Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 1. Place VELCRO 威 hook on[...]

Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the SELECT control on the overhead console. The temperature can be displayed in Centigrade or Fahrenheit by pressing the SELECT control. If th[...]

3. Press and hold the SELECT control until V AR appears in the display , then release. The display should show the current zone number . 4. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated. Compass calibration adjustment Perform this adjustment in an [...]

T o prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand wh[...]

POWER SIDE VIEW MIRRORS (IF EQUIPPED) T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to disable the adjust function. Spotter mirror (if equipped) Note: New spotter mirrors may be stiff, requiring several [...]

The telescoping feature (if equipped) allows the mirror to extend approximately 3.15 inches (80 mm). This feature is especially useful to the driver when towing a trailer . SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does [...]

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL cont[...]

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control [...]

KEYS The key operates all locks on your vehicle. Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Y our keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized deal[...]

Deactivating/activating autolock feature Y our vehicle comes with the autolock feature disabled; there are two methods to enable/disable this feature: • Through your authorized dealer , or • by using a power door unlock/lock procedure. Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is in the 1 (LOC[...]

Back cargo door lock (if equipped) The passenger side rear cargo door has a power door lock control mounted on the inside of the door . When this lock is pressed, all doors will lock/unlock. REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following[...]

If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. T wo step door unlocking 1. Press and release to unlock the driver’ s door . Note: The interior lamps will illuminate if the control on the overhead lamp is not set t[...]

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do n[...]

How to reprogram your remote entry transmitters Y ou must have all remote entry transmitters (maximum of four) available before beginning this procedure. If all remote entry transmitters are not present during programming procedure, the ones missing during programming will no longer operate the vehicle. Note: Ensure the brake pedal is not depressed[...]

The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in[...]

Pull lever up to adjust seatback. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or co[...]

Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. REAR SEATS Rear captains chair adjust — passenger side only Pull the lever forward to adjust the seat forward or backward. 2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Seating and Safety Restraints 62[...]

Quick release captains chair (7 passenger configuration second row only) T o remove the seat: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward. Stow the tongue end of the detachable anchor . 2. Pull the seat latch handle, then pull the seat toward the [...]

T o install the seat: Check to see that the seat and seatback is latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion. Ensure that the seat is latched to the vehicle floor by pushing/pulling on the seat. If not latched, the seat may c[...]

Rear bench seat T o remove the seats: 1. Disengage the lap/shoulder belt from the seat by inserting a key or small screwdriver into the slot in the detachable anchor and lifting upward (2nd row passenger side only). Stow the tongue end of the detachable anchor (2nd row only). 2. Pull the LH/RH seat latch handles (located under the seat) rearward to[...]

4. W ith assistance, remove the seat assembly . • T o remove the 3rd, 4th, and 5th row seats (if equipped), repeat Steps 2 through 4. T o install the seat: Ensure that the seat is latched to the vehicle floor by pushing/pulling on the seat. If not latched, the seat may cause injury during a sudden stop. 1. Position the seat in the vehicle. 2. Ali[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. D[...]

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle. The front outboard and r[...]

This mode should be used any time a child safety seat (except a booster) is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter . How[...]

After any vehicle collision, the safety belt systems at all outboard seating positions (except the driver position, which does not have this feature) must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly . In addition, all safety belts should be checked for prope[...]

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Lap belts Adjusting the center lap belt The lap belt does not adjust automatically . The lap belt should fit [...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The safet[...]

If... Then... The driver’ s safety belt is buckled before the ignition switch is turned to the ON position... The BeltMinder 威 feature will not activate. The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur eve[...]

Reasons given... Consider ... “The people I’m with don’t wear belts” Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed[...]

While the design allows you to deactivate your BeltMinder 威 ,t h i s system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the BeltMinder 威 system activated for yourself and others who may use the vehicle. T o reduce the risk of injury , do not deactivate/activate the BeltMinder 威[...]

the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sur[...]

Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even [...]

Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. See your authorized dealer . Modifying[...]

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the airbag sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong wit[...]

• a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental airbag electrical system wiring (including the impact sensors), the system wiring, the airbag system readiness light, the airbag back up power and the airbag[...]

Passenger airbag ON/OFF switch (if equipped) Note : The passenger airbag ON/OFF switch is on vehicles with no rear seats and a gross vehicle weight rating (GVWR) greater than 8500. See V ehicle loading – with and without a trailer in the T ires, Wheels, and loading chapter . An airbag ON/OFF switch has been installed in this vehicle. Before drivi[...]

In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. An infant in a rear -facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned [...]

If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly . If a child in a rear facing infant seat must be transported in front, the passenger airbag must be turned OFF . This is because the back of the infant seat is too close to the inflating airbag an[...]

• the child has a medical condition which, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’ s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger airbag to pose[...]

• the child has a medical condition that, according to the child’ s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’ s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the ai[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Ford recommends using child safety seats equipped with LA TCH attachments, attached to LA TCH anc[...]

neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. Do not leave children, unreliable adults, or pets unattended in your vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around [...]

T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’ s head (top of ear level) [...]

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably cl[...]

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the sa[...]

tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter . Carefully follow all of the manufacturer’ s instructi[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the[...]

Attaching safety seats with tether straps Children should be placed in the rear in an appropriate child safety seat that is properly secured to the vehicle. When using forward-facing child safety seats in vehicles with only two seating positions so the forward-facing child safety seat cannot be placed in the rear of the vehicle, move the passenger [...]

Front passenger seating position The tether can be attached directly to the rear of the front seat. 1. Position the child safety seat on the front right-hand passenger seat. 2. Adjust the front right-hand passenger seat full forward. 3. Route the child safety seat tether strap over the back of the front right-hand passenger seat as shown. 2007 Econ[...]

4. Clip the tether strap hook to the seat pedestal to the location shown. 5. Adjust the front right hand passenger seat to the full rearward position. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 7. T ighten the child safety seat tether strap according to the manufactur[...]

Second row bucket seats (Chateau Quads) The tether strap can be attached directly to the tether bracket under the back edge of the seat cushion. 1. Position the child safety seat on the second row left hand or right hand bucket seat. 2. Route the child safety tether strap over the back of the left hand or right hand second row bucket seat. 3. Clip [...]

Second, Third and Fourth row three passenger bench seats The tether strap can be attached directly to the tether bracket provided under the back edge of the seat cushion. 1. For second row 3–Passenger bench seat, place the child safety seat on the left hand outboard position, the center position, or the right hand outboard position as desired. Fo[...]

For additional important safety information on the proper use of safety belts, child seats and infant seats, please read the entire Seating and Safety Restraints chapter in this Owner’ s Guide . Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats have two rigid or[...]

• Eight passenger wagon • T welve passenger wagon • Fifteen passenger wagon represents LA TCH anchors. represents tether strap anchors. Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. 2007 E[...]

The lower anchors for child seat installation are located at the rear section of the seat between the cushion and seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. Attach LA TCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigi[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

VEHICLE CHARACTERISTICS How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. • Shorter – to give i[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are [...]

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate [...]

Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an [...]

Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may res[...]

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve [...]

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. T ire service, including adjusting tire pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safet[...]

Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Al[...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]

Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect[...]

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved[...]

• DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. W e do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair . After tire rotation, inflation pressures must be adjusted for the tires new position[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same [...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label). Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEV[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2007 E[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driv[...]

to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 [...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-150 Regular/R V V an (8520 GVWR) 4.6L 3.73 11500 (5216) 6000 (2722) 60 (5.52) 4.6L 4.10 12000 (5443) 6500 (2948) 60 (5.52) E-150 V an (Crew) (8520 GVWR) 4.6L[...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-150 Regular W agon (8–passenger) (8600 GVWR) 5.4L 3.55 12000 (5443) 6100 (2767) 60 (5.52) 5.4L 3.73 13000 (5897) 7100 (3221) 60 (5.52) E-250 Regular/R V V [...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-250 Extended/R V V an (9000 GVWR) 5.4L 3.73 13000 (5896) 7400 (3357) 60 (5.52) E-250 Extended V an (Crew) (9000 GVWR) 5.4L 3.73 13000 (5896) 7200 (3266) 60 ([...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 5.4L 4.10 13000 (5897) 7300 (3311) 60 (5.52) 6.8L 3.73 15000 (6804) 9100 (4128) 60 (5.52) 6.8L 4.10 18500 (8391) 10000 (4536) 60 (5.52) E-350 Extended V an (Cr[...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Cutaway (138” wheelbase, dual rear wheel) (10000 GVWR) 5.4L 4.10 13000 (5897) 7900 (3583) 60 (5.52) 6.8L 4.10 18500 (8391) 10000 (4536) 60 (5.52) E-350[...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 5.4L 4.10 13000 (5897) 8800 (3992) 8800 (3992) E-350 Stripped Chassis (158” wheelbase, single rear wheel) (9600 GVWR) 5.4L 3.73 13000 (5897) 8700 (3946) 60 ([...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) E-350 Stripped Chassis (176” wheelbase, dual rear wheel) (10000 GVWR) 5.4L 4.10 13000 (5897) 8400 (3810) 60 (5.52) 6.8L 4.10 18500 (8391) 10000 (4536) 60 (5.[...]

GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR - lb. (kg) Maximum Loaded T railer W eight - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) Maximum trailer weight for all cutaway (E-350 and E-450) vehicles must be calculated by subtracting the weight of the vehicle (including incomplete vehicle wei[...]

Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety ch[...]

• Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. • Anticipate stops and brake gradually . When descending long, steep downhill grades, always use a lower gear to provide engine braking to save wear on brakes. Use Dr[...]

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water . When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper . • [...]

STARTING Positions of the ignition 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel. This position also allows the automa[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding a[...]

• Make sure the parking brake is set. • Make sure the gearshift is in P (Park). • T urn the key to 4 (ON) without turning the key to 5 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. T urn the key t[...]

Note: If the engine does not start within five seconds on the first try , turn the key to 3 (OFF), wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. Guarding against exhaust fumes Car[...]

Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the A[...]

Parking brake T o set the parking brake (1), press the parking brake pedal down until the pedal stops. T o release, pull the lever (2). Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. The parki[...]

over -spinning. When the brakes have cooled down, the system will again function normally . Anti-lock braking is not affected by this condition and will function normally during the cool-down period. The AdvanceT rac 威 with RSC system enhances your vehicle’ s stability during maneuvers that require all available tire traction, like in wet/snowy[...]

vehicle is traveling in R (Reverse). In R (Reverse), ABS and the traction enhancement feature will continue to function. The AdvanceT rac 威 with RSC button allows the driver to control the availability of the AdvanceT rac 威 with RSC system. AdvanceT rac 威 with RSC system status is indicated by a warning indicator light with a “sliding car?[...]

• A slight deceleration of the vehicle • Steering feedback • The AdvanceT rac 威 with RSC indicator light will flash • If your foot is on the brake pedal, you will feel a vibration in the pedal. All these conditions are normal during AdvanceT rac 威 with RSC operation. Do not alter or modify your vehicle’ s suspension, steering or tires[...]

If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull. T RACTION-LOK AXLE (IF EQUIPPED) This axle provide[...]

Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over loading or loading the vehicle improper[...]

and/or personal injury . Use all available road surface to return the vehicle to a safe direction of travel. • In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements. V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles [...]

Do not drive your vehicle until you verify that the brakelamps are working. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the bra[...]

T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Re[...]

• T o return to O/D (Overdrive), press the transmission control switch. The O/D OFF lamp will not be illuminated. • O/D (Overdrive) is automatically returned each time the key is turned off. 2 (Second) This position allows for second gear only . • Provides engine braking. • Use to start-up on slippery roads. • T o return to (Overdrive), m[...]

Understanding the shift positions of the 5–speed automatic transmission (if equipped - 5.4L and 6.8L gasoline engines only) This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type [...]

N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with T ow/Haul OFF D (Overdrive) with T ow/Haul OFF is the normal driving position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through g[...]

3 (Third) T ransmission starts and operates in third gear only . Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearsh[...]

• Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a compl[...]

Used for improved traction on slippery roads. Selecting 3 (Third) provides additional engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • The transmission will not downshift in[...]

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. T o h[...]

The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]

V EHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to the engine or transmission to operate utility equipment. Examples include wheel-lift for tow trucks, tools for construction, and cranes. PTO applications draw auxiliary horsepower from the powertrain, often while the vehicle is stationary[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty perio[...]

Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick refer[...]

HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it whe[...]

Except for commercial stripped chassis vehicles, this switch is located in the front passenger’ s footwell, by the kick panel. 2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 166[...]

On commercial stripped chassis vehicles, this switch is located on a bracket above the brake pedal. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition ON. 5. W ait a few seconds and return the key to OFF . 6. Mak[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A 4–Wheel Anti–lock Brake System (4W ABS) module 2 10A Remote Keyless Entry (RKE), O/D cancel, IVD module 3 15A T rip computer , Radio, Overhead console 4 15A Courtesy lamps 5 30A Power lock switches, Power locks without RKE 6 10A[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 15A Radio capacitor(s), Ignition coil, Powertrain Control Module (PCM) diode, PCM power relay 9 5A W iper control module 10 20A Main light switch, Park lamps, License lamp (external lamps), Multi-function switch (flash-to-pass), BSM 11 15A Multi-function switch (haza[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 27 5A Radio 28 — Not used 29 — Not used 30 15A Headlamps (high beam indicator) 31 10A Right headlamp (low beam) 32 20A Power point #1 (instrument panel) 33 10A Start relay 34 — Not used 35 — Not used 36 5A Instrument illumination 37 — Not used 38 — Not used[...]

T o reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter . The high-current fuses are coded as follows. Fuse/Relay Location[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 8 40A** T railer battery charge relay 9 50A** Modified vehicle power 10 30A** Electric brake controller 11 60A** 4-Wheel Anti-lock Brake System (4W ABS) 40A** AdvanceT rac 威 with RSC 12 60A** I/P fuses 29, 34, 35, 40 and 41 13 20A** Fuel pump relay 14 50A** Auxiliary blower re[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 26 20A* T railer tow turn signals 27 10A* PCM keep alive, Canister vent (gasoline engine only) 28 — Not used A — Fuel pump relay B — Horn relay C — T railer back-up lamps relay D — T railer running lamps relay E — T railer battery charge relay F — IDM relay (diesel[...]

The relays are coded as follows: Relay location Description 1 Interior lamps 2 Open 3 Open 4 Battery saver Engine compartment relay module The engine compartment relay module is located in one of two places depending on which type of engine your vehicle is equipped with: • Gasoline engine: driver side of the engine compartment above the brake mas[...]

• hold the steering wheel firmly . • slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is [...]

• Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessar[...]

Full-size Matching Spare Tire/Wheel Information This spare tire/wheel will match the road tire/wheel. When driving with the full size matching spare tire/wheel, do not exceed 70 mph (113 km/h). It is intended for temporary use only . This means if you need to use it, you should replace it as soon as possible. Stopping and securing your vehicle 1. P[...]

3. Remove the jack handle from the right side compartment and insert the tip of the jack handle through the access hole and into the tube. 4. T urn the jack handle counterclockwise until the cable is slack and the tire can be slid from under the vehicle. 5. Remove the retainer from the spare tire. T o stow the cable retainer with the spare removed,[...]

5. Block the wheel that is diagonally opposite the tire you are changing. On E-450 vehicles, the parking brake is on the transmission. Therefore, the vehicle will not be prevented from moving when a rear wheel is lifted, even if the parking brake is applied. Be sure to block both directions of the wheel that is diagonally opposite to the wheel that[...]

7. Use the tapered end of the lug nut wrench to unscrew wheel ornaments attached by retaining screws. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. 8. Loosen the wheel nut by pulling up on the handle of the lug nut wrench about one-half turn (counterclockwise). Do not remove the wh[...]

Rear axle jacking points - All models except E-350 Dual Rear Wheel (DR W) and E-450: Rear axle jacking points - E-350 Dual Rear Wheel (DR W) and E-450: Front axle jacking points: Place the jack under the pin on the front surface of the front axle. Do not place the jack under or on the steering linkage. • Raise the jack until the wheel is complete[...]

If your vehicle has single rear wheels, thread the lug nuts on the studs with the beveled face toward the wheel. If your vehicle has dual rear wheels, thread the two element swiveling lug nuts on the studs with the flange facing toward the wheel. 3. Use the lug nut wrench to screw the lug nut snugly against the wheel. 4. Lower the vehicle by turnin[...]

3. T urn the jack handle clockwise until the tire is raised to its stowed position underneath the vehicle. The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness. T ighten to the best of your ability , to the point where the ratchet/slip occurs, if pos[...]

On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or b[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning proce[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 187[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the bat[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing pr[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca Away from home–motorhome service If you own a motorhome built on a Ford Chassis and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could [...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator NHTSA 400 Seventh Street, SW W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING SAFETY [...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

W AXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product. • Do[...]

• Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergent. • T o remove tar and grease, use Motorcraft Bug and T ar Remover (ZC-42), available from your authorized dealer . ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer[...]

• If tar or grease spots are present, use Motorcraft Bug and T ar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle[...]

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted sur[...]

• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber , vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear , protective coating. Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leat[...]

Motorcraft Premium Liquid W ax (ZC-53-A) Motorcraft Premium W indshield W asher Concentrate (ZC-32–A) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft T ire Clean and Shine (ZC-28) Motorcraft T riple Clean (U.S. only) (ZC-13) Motorcraft Ultra-Clear Spray Glas[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide/Owner Information Guide to find out which parts and services[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood and secure it with the prop rod. HOOD 2007 Econoline (eco) Owners Guide (post-2002-fmt) [...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Engine compartment component locations Refer to the 6.0 Liter Power Stroke Direct Injection T urbo Diesel Owner’ s Guide Supplement for diesel engine component locations. 1. W indshield washer fluid reservoir 2. Engine oil filler cap 3. Automatic transmission fluid dipstick 4. Air filter assembly 5[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

Poor wiper quality can be improved by cleaning the wiper blades and the windshield, refer to Windows and wiper blades in the Cleaning chapter . T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge o[...]

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil level[...]

5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until three clicks are heard or until the cap is fully seated. T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed. Engine oil and filter recommendations Look for this certific[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Als[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling a[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]

remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the ca[...]

Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Maintenance product specifications and capacities in this chapter . Fill y[...]

What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain. How fail-safe cooling works If the engine begins to ove[...]

Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to an authorized dealer . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to an authorized dealer as soon as possible. FUEL FILTER For fuel filter replacement, see[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally , adding one gallon of fuel is enough to restart the engine. If the vehicle is [...]

• Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same[...]

• Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy . • Slow down gradually . • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h[...]

• Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Close windo[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate tha[...]

3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter . 4. Driving through deep water – the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving [...]

vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30 second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine.[...]

4. T urn the engine off. For E-450 and E-550 vehicles with the Hydro-Boost Brake System, do not press the brake pedal after the engine has been turned off. Pressing the brake pedal after the engine has been turned off will give a false power steering fluid level reading. 5. Recheck the fluid level on the dipstick. Do not add fluid if the level is b[...]

temperature (approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temp[...]

The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating [...]

Automatic transmission fluid filter (if equipped) The T orqshift automatic transmission is equipped with a serviceable external fluid filter mounted on the driver’ s side of the transmission as shown in the illustration. T orqshift transmissions which do not have the externally mounted filter will have the transmission fluid filter located inside[...]

Changing the air filter element 1. Disconnect the fresh air inlet tube from the radiator support. 2. Open the clamp that secures the two halves of the air filter housing together . 3. Carefully separate the two halves of the air filter housing. 4. Remove the air filter element from the housing. 5. Install a new air filter element. Be careful not to[...]

MOTORCRAFT PART NUMBERS Component 1 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Air filter element F A-1632 F A-1632 F A-1632 Battery- standard / (auxiliary) BXT -65-650 / (BXT -65-750) BXT -65-650 / (BXT -65-750) BXT -65-650 / (BXT -65-750) Fuel filter FG-872 FG-872 FG-872 Oil filter FL-820-S FL-820-S FL-820-S PCV valve 2 Spark plugs 3 T orqshif[...]

Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used. 4 Also available with 6.0L Diesel engine/T orqShift transmission. Externally–mounted filter eleme[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1 or PM-1-C / ESA-M6C25-A or WSS-M6C62-A Door weatherstrips — Silicone Spray Lubricant XL-6 / ESR-M13P4-A Hinges, latches,[...]

Item Capacity Ford part name Ford part number / Ford specification Engine coolant 4.6L engine 23.8 quarts (22.6L) Motorcraft Premium Gold Engine Coolant with bittering agent (yellow-colored) 1 VC-7-B / WSS-M97B51-A1 Engine coolant 4.6L engine with aux rear heat 26.0 quarts (24.6L) Engine coolant 5.4L engine 28.8 quarts (27.2L) Engine coolant 5.4L e[...]

Item Capacity Ford part name Ford part number / Ford specification Engine oil-gasoline engine 6.0 quarts (5.7L) Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) 2 XO-5W20-QSP (US) CXO-5W20- LSP12 (Canada) / WSS-M2C930-A with API Certification Mark Engine oil-diesel engine Refer to t[...]

Item Capacity Ford part name Ford part number / Ford specification Dana Limited Slip Axle fluid M60 (M248) E250/E350 5.9 pints (2.8L) 5,7 SAE 90 Hypoid Gear Oil XY–90–GL / ESW -M2C105-E Dana Limited Slip Axle fluid M70FF (M267FF) E-350 6.6 pints (3.1L) 7 Dana Limited Slip Axle fluid M70HD (M273HD) E-450 8.3 pints (3.9L) 7 Dana conventional axle[...]

Item Capacity Ford part name Ford part number / Ford specification W indshield washer fluid 4.2 quarts (4.0L) Motorcraft Premium W indshield W asher Concentrate ZC-32-A / WSB-M8B16-A2 Fuel tank–all regular and extended length vans and wagons 35.0 gallons (132.4L) —— Fuel tank–138 inch wheelbase (except E-Super Duty) 37.0 gallons (140.0L) Fu[...]

4 Automatic transmissions that require MERCON 威 V should only use MERCON 威 V fluid or fluid that is specified dual usage MERCON 威 / MERCON 威 V . Refer to scheduled maintenance information to determine the correct service interval. Use of any fluid other than the recommended fluid may cause transmission damage. Automatic transmissions that r[...]

ENGINE DATA Engine * 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Cubic inches 281 330 415 Required fuel 87 octane 87 octane 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Ignition system C o i lo np l u g C o i lo np l u g C o i lo np l u g Spark plug gap 0.052–0.056 inch (1.32–1.42mm) 0.052–0.056 inch (1.32–1[...]

• 4.6L V8 and 5.4L V8 Engines with A/C • 6.8L V10 Engine V EHICLE IDENTIFICATION NUMBER Complete Ford built vehicles The vehicle identification number is attached to your vehicle in the following places: • The top of the instrument panel on the driver’ s side. 2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Speci[...]

• On the certification label. This label is required by the National Highway T raffic Safety Administration and is made of special material. If it is tampered with, it will be destroyed or a destruction pattern will appear . The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake sys[...]

T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents. Description Code Five-speed automatic T orqShift-diesel engine with overdrive cancel B Four -speed automatic overdrive (4R75E) Q Five[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Peace of mind Mobile-Ease 娂 hands-free communication system Remote start V ehicle security systems Not all accessories are available for all models. For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your ve[...]

A Accessory delay .......................... 49 AdvanceT rac .............................. 145 Air cleaner filter ............... 237–239 Airbag supplemental restraint system .................................... 76–77 and child safety seats .............. 78 description ................................ 77 disposal .............................[...]

wheels ...................................... 201 wiper blades ............................ 203 Climate control (see Air conditioning or Heating) ...... 31–33 Clock adjust 6-CD in dash .......................22, 27 AM/FM ....................................... 20 Compass, electronic ....................47 calibration .............................[...]

Fluid capacities ......................... 241 Four -Wheel Drive vehicles preparing to drive your vehicle ..................................... 149 Fuel ............................................ 222 calculating fuel economy ....... 227 cap ........................................... 224 capacity ................................... 241 choosing t[...]

headlamps, flash to pass .......... 35 instrument panel, dimming ..... 36 interior lamps ........................... 38 replacing bulbs ......................... 40 Lane change indicator (see T urn signal) ........................ 38 Lights, warning and indicator .... 12 anti-lock brakes (ABS) .......... 144 Load limits ............................[...]

Seat belts (see Safety restraints) ............... 66 Seats ............................................ 60 child safety seats ...................... 90 front seats ................................. 60 Servicing your vehicle .............. 207 Setting the clock AM/FM stereo ...........................20 AM/FM/In-dash 6 CD .......... 22, 27 Spare ti[...]

258[...]

259[...]

260[...]

261[...]

262[...]

263[...]

264[...]