Ford 2011 Escape Hybrid manual

Introduction 4 Instrument Cluster 18 W arning lights and chimes 18 Gauges 23 Message center 25 Entertainment Systems 34 AM/FM stereo with CD/MP3 34 Auxiliary input jack (Line in) 42 USB port 44 Satellite radio information 48 Navigation system 51 SYNC 威 51 Climate Controls 52 Dual automatic temperature control 52 Rear window defroster 56 Lights 57[...]

Seating and Safety Restraints 1 15 Seating 115 Safety restraints 127 Airbags 142 Child restraints 157 Tires, Wheels and Loading 175 T ire information 177 T ire inflation 179 T ire Pressure Monitoring System (TPMS) 193 V ehicle loading 198 T railer towing 205 Recreational towing 210 Driving 21 1 Starting 211 Brakes 216 AdvanceT rac 威 219 T ransmis[...]

Maintenance and Specifications 291 Engine compartment 294 Engine oil 297 Battery 300 Engine Coolant and Motor/Electronics Coolant 302 Fuel information 308 Air filter(s) 320 Part numbers 324 Maintenance product specifications and capacities 325 Engine data 328 Accessories 331 Ford Extended Service Plan 334 Scheduled Maintenance Guide 338 Normal sche[...]

CONGRATULATIONS Congratulations on acquiring your new Ford Hybrid. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the fol[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

new vehicle operation. V ary your speed frequently in order to give the moving parts a chance to break in. Drive your new vehicle at least 1,000 miles (1,600 km) before towing a trailer . For more detailed information about towing a trailer , refer to T railer towing in the T ires, Wheels and Loading chapter . Do not add friction modifier compounds[...]

• Charge level of high voltage battery is low • V ery high or low outside temperature (to provide system cooling/heating) • Engine not warm enough to provide passenger requested cabin temperature Stopping: The gas engine may shut off to conserve fuel as you come to a stop. Restarting the vehicle is not required. Simply step on the accelerator[...]

If the vehicle is left inoperative for over 31 days, it may be necessary to jumpstart the vehicle. For more information, refer to Jump starting (Low voltage [underhood] battery only) in the Roadside Emergencies chapter and also refer to Low and high voltage battery — storage in the Maintenance and Specifications chapter . Engine: The engine speed[...]

achieved with mild to moderate acceleration and deceleration. Moderate braking is particularly important since it allows you to maximize the energy captured by the regenerative braking system. NOTE: Having your engine running is not always an indication of inefficiency – in some cases it is actually more efficient than driving in electric mode. A[...]

Question Answer After I start my car in the morning, why does it take a long time before the engine shuts down? There are several reasons the engine stays on for an extended amount of time when it is first started. One common reason is to ensure that the emissions components are warm enough to minimize tailpipe emissions. As the climate gets cooler[...]

Question Answer What is the fan noise I hear from the rear of my hybrid? The fan noise comes from two fans located inside the high voltage battery . These fans turn on when the battery requires cooling air . The fan speed, and associated noise level, will change according to both the amount of cooling required and the speed of the vehicle to mainta[...]

SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide. Special instructions For your added safety , your vehicle is fitted with sophisticated electr[...]

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly d[...]

limitations regarding 911 Assist and T raffic, directions and Information privacy below). However , parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. T o read data recorded by an EDR, special equipment is required, and access to the vehicle or t[...]

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES Shown in standard measure. Metric similar . W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to mak[...]

W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turn[...]

Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature. Stop safely hazard warning: Indicates hybrid component fault/failure that will cause the vehicle to shutdo[...]

High engine or high motor electronic coolant temperature: Illuminates when the engine coolant or motor electronics coolant temperature is high. The message center displays HIGH ENGINE TEMPERA TURE / HIGH MOTOR TEMPERA TURE when the engine coolant or motor electronics are overheating. Stop the vehicle as soon as safely possible, turn off the engine,[...]

Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. Anti-theft system: Flashes when the SecuriLock 威 passive anti-theft system has been activated. Throttle control/[...]

HEV engine off reminder chime: Sounds for 10 seconds when the PRNDL is in the P (Park) position and the Driver’ s door is ajar (open) while ignition is on. Always turn your ignition key to off and remove key before leaving your vehicle. (The engine may be off when the vehicle is stopped, yet the key is on, and the engine can turn on at any time) [...]

Battery gauge: Provides information about the vehicle’ s energy usage. • ASSIST — Battery provides extra power to boost the vehicle’ s acceleration. • CHARGE — Storing extra energy in the battery when coasting or slowing down. Odometer: Registers the total miles (kilometers) of the vehicle. Refer to Message center in this chapter on how[...]

MESSAGE CENTER Y our vehicle’ s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with an informational message followed by a long indicator chime. The message center display is located in the instrument cluster . Info Press the INFO button repeatedly to cycle thro[...]

A VG MPG (L/100km) A verage fuel economy displays your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing distance traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Y our vehicle was [...]

System check and vehicle feature customization Press the SETUP button repeatedly to cycle the message center through the following features: PRESS RESET FOR ENGLISH When entering the setup menu and a non-English language has been selected, this message will be displayed to change back to English. Press the RESET button to change back to English. RE[...]

Note: T o change oil life 100% value to another value, proceed to Step 3. 3. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET button to change the Oil Life Start V alue. Each release and press will reduce the value by 10%. UNITS Displays the current units English or Metric. Press the RESET button to change from English to M[...]

LANGUAGE = ENGLISH / SP ANISH / FRENCH Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French. W aiting four seconds or pressing the RESET button cycles the message center through each of the language choices. Press and hold the RESET button for two seconds to set the language ch[...]

Note: If the vehicle is still running, it may soon shut down without further warning and should be stopped safely . Contact your authorized dealer as soon as possible. HIGH ENGINE TEMPERA TURE — Displayed when the engine coolant is overheating. Engine coolant temperature warning lamp will illuminate indicating coolant temperature is high. Stop th[...]

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately . Refer to Brake fluid in the Maintenance and Specifications chapter . LOW TIRE PRESSURE — Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating your tires in the T ires, Wheels and Loading ch[...]

VEHICLE NEAR TOP SPEED — Displayed when a MyKey™ is in use and the MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h). Refer to MyKey™ in the Locks and Security chapter for more information. TOP SPEED MYKEY SETTING — Displayed when a MyKey™ is in use and the MyKey speed limit is on and the vehicle speed is 80 m[...]

SP ACE FOUND PULL FOR W ARD (if equipped) — May display when using the active park assist system. See Active park assist in the Driving chapter for more information. SP ACE FOUND STOP (if equipped) — May display when using the active park assist system. See Active park assist in the Driving chapter for more information. PULL FOR W ARD USE CAUTI[...]

AUDIO SYSTEMS AM/FM/single CD/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is the safe operation of t[...]

AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off. T urn the knob to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition is turned back on. AM/FM: Press repeatedly to select AM/FM1/FM2 frequency band. TUNE: T [...]

T o activate the autoset feature: Press MENU repeatedly until AUTO PRESET ON/OFF appears in the display . Use SEEK/TRACK to turn AUTO PRESET to ON, and either wait five seconds for the search to initiate or press OK to immediately initiate the search. If you press another control within those five seconds, the search will not initiate; the 10 stron[...]

/ Play/Pause: Press to play/pause a track when playing a CD. SEEK/TRACK: Press SEEK/TRACK to access the previous/next track. CA T (Category) / FOLD (Folder): In MP3 mode only– Press CA T/FOLD and then press SEEK/TRACK to access the previous/next folder . SCAN: Press for a brief sampling of all tracks on the current disc or MP3 folder . DIRECT : I[...]

SHUFFLE: Press SHUFFLE to turn on and off and begin/stop random play . The system will only shuffle the disc currently playing. Satellite Radio Satellite radio is available only with a valid SIRIUS 威 radio subscription. Check with your authorized dealer for availability . SIRIUS: Press to access satellite radio mode, if equipped. Press repeatedly[...]

MEMOR Y PRESETS (0–9): There are 30 available presets, 10 each for SA T1, SA T2 and SA T3. T o save satellite channels in your memory presets, tune to the desired channel then press and hold a memory preset number (0–9) until sound returns. TEXT : Press and release to display the artist and song title. While in TEXT MODE, press again to scroll [...]

an audible prompt. Press OK while SONG ALERT is in the display and the system will take you to the channel playing the desired song. Y ou can save up to 20 song titles. If you attempt to save more than 20 titles, the display will read REPLACE SONG? Press OK to access the saved titles and press / to cycle through the saved titles. When the song titl[...]

b. CHANGE PIN: Press OK when CHANGE PIN is displayed. The display will read ENTER OLD PIN. Enter your current (old) PIN number and when the system accepts your entry it will display ENTER NEW PIN. Enter your new four -digit PIN and the system will save the new PIN and PIN SA VED will display . c. UNLOCK ALL CHANNELS: Press OK when UNLOCK ALL CHANNE[...]

Extra Features AUX: Press repeatedly to cycle through LINE IN (auxiliary audio mode), and SYNC 威 (if equipped). For location and further information on auxiliary audio mode, refer to Auxiliary input jack later in this chapter . If your vehicle is equipped with SYNC 威 , refer to the SYNC 威 information included with your vehicle for further inf[...]

Y our vehicle is equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity . T o achieve optimal performance, please observe the following in[...]

7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD controls. T roubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ. [...]

Y our vehicle may be equipped with a USB port located on the instrument panel. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature. For further information on this feature, refer to Accessing and using your USB port in the SYNC 威 supplement or Navigation System supplemen[...]

CD/CD player care Do: • Handle discs by their edges only . (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner . • W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are[...]

CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio[...]

Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 d[...]

• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible st[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. Y o ua r ei nal o c a t i o nt h a t is blocking the SIRIUS 威 signal (i.e., tunnel, under an overpass, dense foliage, etc). The system is working properly . When you move into an open area, the signal should r[...]

DUAL AUTOMATIC TEMPERATURE CONTROL 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflow distribution, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature. T urn to increase/decrease the temperature on the driver side[...]

5. Power/ : Press to activate/deactivate the climate control system. When the system is off, outside air is shut out. Press + or – to manually increase/decrease the fan speed. The manual fan speed setting will appear on the left side of the display . Press AUTO to return to full automatic control. 6. Panel: Distributes air through the instrument [...]

11. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed to cool down the interior of the vehicle, may reduce the energy needed to keep the interior of the vehicle cool, and may also help reduce undesired outside odors from reaching the interior of the vehicle. Recirc[...]

• A small amount of air may be felt from the floor vent regardless of the air distribution setting that is selected. During extreme high ambient temperatures when idling stationary for extended periods of time in gear , it is recommended to run the A/C in the MAX A/C position, reduce blower fan speed from the highest setting and put the vehicle?[...]

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The vehicle must be on to operate the rear window defroster . Press R to turn the rear window defroster on. An indicator light on the button will illuminate when active. The rear window defroster turns o[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the head[...]

2. Rotate the headlamp control to the autolamp position. 3. Rotate the headlamp control to the off position. 4. T urn the vehicle on. 5. T urn the vehicle off. 6. T urn the headlamp control to the autolamp position (the headlights should turn on). 7. T urn the headlamp control to the off position when the desired delay time (up to three minutes) ha[...]

Flash-to-pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the low beam headlamps on with a reduced output. T o activate: • the ignition must be in the on position. • the headlamp control must be in the off , parking lamps or autolamp position. • the transmission is not in P [...]

Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. This will ensure that your displays are visible under all lighting conditions. AIMING THE HEADLAMPS The headlamps on your vehicle are p[...]

5. Locate the vertical adjuster on the headlamp, then us ea4m m socket to turn the adjuster either counterclockwise (to adjust up) or clockwise (to adjust down) aligning the upper edge of the light pattern to the horizontal line. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp. 7. Close [...]

The map lamp controls (without moon roof) are located on the dome lamp. Press the button on either side of each map lamp to illuminate the lamps. Press the button again to turn off the lamps. For models equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the button on either side of each map lamp to illuminate[...]

Ambient lighting (if equipped) Illuminates footwells, cupholders, the console bin and the console tray with a choice of several colors. The ambient lighting control switch is located on the floor console. T o activate, press and release the control to cycle through the color choices plus the off state. The lights come on whenever the ignition is in[...]

T ake your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present. Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern[...]

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Reach over the front bolster . 4. Remove the bulb by turning it counterclockwise and then pulling it straight out. 5. Disconnect the electrical connector from the bulb. W ARNING: Handle a halogen headlamp bulb carefully and keep out of child[...]

5. Carefully pull the bulb out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. Replacing front sidemarker bulbs For bulb replacement, see your authorized dealer . Replacing tail/stop/turn/sidemarker/backup lamp bulbs The tail/stop/turn/sidemarker/backup lamp bulbs are located in the sa[...]

Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Depress the lever and carefully pry the license plate lamp assembly (located above the license plate) from the liftgate. 3. Rotate the bulb socket counterclockwise and remove from lamp assembly . 4. Pull bulb straight out of socket and push in the new bul[...]

3. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in reverse order . Replacing fog lamp bulbs (if equipped) 1. Make sure the fog lamp switch is in the off position. 2. From underneath the vehicle, carefully disconnect the electrical connector from the bulb. 3. Remove the bu[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the wipers will swipe thre[...]

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: 2 — Normal speed operation of rear wiper . 1 — Intermittent operation of rear wiper . O (off) — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control [...]

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps. Slide-on-rod feature The visor will slide back and forth on the rod for increased sunlight coverage. Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: T o stow the visor back into the headliner , visor must be retr[...]

Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. T urn ignition to the on position. 3. Start the engine. 4. Press the SETUP control to select the Update Zone function and display the current ZONE XX in the center stack display . 5. Continue to press the RESET control u[...]

2. T o calibrate, press and hold the RESET control for approximately ten seconds until CAL appears. Release the control. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value. It may take up to five circles to complete calibration. 4. The compass is now calibrated. CENTER CONSOLE Y o[...]

The tray and inside bin can be removed to open up space to fit a laptop computer , MP3 players, CDs or handbags. T o remove, open the console lid and pull the bin straight up and out from the console housing. The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage. AUXILIARY POWER POINT (12V) Power outlets[...]

T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is not running, • do not leave battery chargers, video game adapters, computers and other devic[...]

defeat the safety protection design provided by the cap and twist tab. It will also cause the power point to overload due to powering multiple devices that can reach beyond the 150W load limit. The power point can switch to a fault mode when it is overloaded, overheated, or shorted. For overloading and shorting conditions, unplug your device and tu[...]

One-touch down Allows the driver’ s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation. Window lock The window lock feature allows only the driver to operate the pow[...]

Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor . Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a rearview camera system, a video image will display in the mirror or the nav[...]

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Do not clean the housing or g[...]

3. Press and release SET +. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • [...]

Turning of f speed control T o turn off the speed control, press OFF or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS These controls allow you to operate some audio control features. Radio control features VOL + (V olume): Press to increase th[...]

SYNC 威 system hands-free control feature (if equipped) Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command. Press to activate phone mode or answer a phone call. Press and hold to end a call or exit phone mode. Press to scroll through various me[...]

T o open the moon roof: The moon roof is equipped with an automatic, one-touch, opening, closing and venting feature. Press and release the rear portion of the control. T o stop motion at any time during the one-touch operation, press the control a second time. W ARNING: When closing the moon roof, you should verify that it is free of obstructions [...]

The moon roof has a sliding shade that can be opened or closed when the glass panel is shut. T o close the shade, pull it toward the front of the vehicle. Accessory delay: W ith accessory delay , the window switches, audio system, and moon roof (if equipped) may be used for up to 10 minutes after the ignition switch is turned off or until either fr[...]

Read the instructions completely before attempting to program the Car2U 威 system. Because of the steps involved, it may be helpful to have another person assist you in programming the transmitter . Additional Car2U 威 system information can be found on-line at www .learcar2U.com or by calling the toll-free Car2U 威 system help line at 1-866-572[...]

1. Firmly press the two outer Car2U 威 system buttons for 1–2 seconds, then release. 2. Go to the garage to locate the garage door opener motor and its “learn” button. Y ou may need a ladder to reach the unit and you may need to remove the unit’ s cover or light lens to locate the “learn” button. Press the “learn” button, after whi[...]

After successful programming, you will be able to operate your Car2U 威 system by pressing the button you programmed to activate the opener . The indicator light above the selected button will turn on to confirm that the Car2U 威 system is responding to the button command. T o program another rolling code device such as an additional garage door [...]

Switch position 1234567 8 9 1 0 1 1 1 2 Up, on or + LLLLLLL L L L L L Middle, neutral or 0 MMMMMMM MMMMM Down, o f fo r– RRRRRRR R R R R R L=left; M=middle; R=right 3. T o input these positions into the Car2U 威 system, simultaneously press all three Car2U 威 system buttons for a few seconds and then release to put the device into programming m[...]

5. Press and hold the Car2U 威 system button you would like to use to control the garage door . Immediately (within 1 second) release the button once the garage door moves. During this time the selected button indicator light will blink slowly . Do not release the button until you see the garage door move. Most garage doors open quickly . Y ou may[...]

FCC and RSS-210 Industry Canada Compliance The Car2U 威 system complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesire[...]

Do not open the liftgate or liftgate window in a garage or other enclosed area with a low ceiling. If the liftgate window is raised and the liftgate is also opened, both liftgate and window could be damaged against a low ceiling. Do not leave the liftgate or liftgate window open while driving. Doing so could cause serious damage to the liftgate and[...]

W ARNING: Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of a sudden stop or collision. ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel. For proper function of the roof rack system, loads must be placed directly on crossbars affixed to[...]

T o remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross-bar assembly off th[...]

T o reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to press the tongue in the endcaps on both sides of the cross-bar . 3. Slide the cross-bar assemblies over the end cap ton[...]

KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your vehicl[...]

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to the vehicle can be activated as a MyKey™. The key will remain restricted until MyKey™ is cleared. Any remaining keys are referred to as an “administrator key” or admin key . The admin key can be[...]

Create a MyKey™ T o program MyKey™ on one of the keys programmed to the vehicle, insert the key that you want to make a MyKey™ into the ignition. T urn the ignition on. Use the message center buttons to do the following: 1. Press SETUP until PRESS RESET TO CREA TE MYKEY is displayed. 2. Press and release the RESET button. HOLD RESET TO CONFIR[...]

Clear MyKey™ T o reset all MyKeys™ as admin keys do the following: 1. T urn the vehicle on using the admin key . 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRM CLEAR is displayed. 4. Press and hold the RESET button for two seconds until ALL MYKEYS CLEARED is displayed. [...]

3. Follow Steps 1-4 in the Create a MyKey™ section. Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or ADMIN KEYS PROGRAMMED that is displayed in the MyKey™ system status menus will include the remote start system as an additional key in the total count. See the Check MyKey™ system status section. Note: For all vehicles with remote [...]

Condition Potential Causes Cannot clear MyKey™ • Key in the ignition is a MyKey™ • No MyKeys™ are programmed to the vehicle. Refer to Create a MyKey™ section • V ehicle has been started using a remote start system that is programmed as MyKey™. Refer to Using MyKey™ with remote start systems section. Lost the only admin key • Pur[...]

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors T urn the key in the door cylinder to unlock the driver’ s door only . All other doors will remain locked. Locking the doors T urn the key in the door cylinder to lock the driver’ s door only . Auto[...]

Note: The autolock feature can be activated/deactivated independently of the autounlock feature. Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is in the off position, and all vehicle doors, liftgate and liftgate window are closed. Power door unlock/lock procedure Y ou must co[...]

Message center procedure For information on activating/deactivating the autolock feature using the vehicle’ s message center , refer to Message center information in the Instrument Cluster chapter . Autounlock The autounlock feature will unlock all the doors when: • the ignition is in the on position, all the doors are closed, and the vehicle h[...]

1. Place the key in the ignition and turn the ignition to the on position. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition from the on position to the off position. 4. Press the power door unlock control on the door panel three times. 5. T urn the ignition back to the on position. The horn will chirp one [...]

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the childproof door locks are set, but the doors are unlocked. The childproof locks are located on the rear edge of each rear door and must be set separately for each door . Note: Setting the lock for o[...]

The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the power liftgate glass. • activate the personal alarm. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position. The [...]

4 seconds. The turn signal will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two step unlocking. Locking the doors 1. Press and release to lock all the doors. Assuming all vehicle doors and the liftgate are properly closed and the parking lamps will flash once. 2. Press and rele[...]

T o replace the battery: 1. T wist a thin coin in the slot of the IKT near the key ring in order to remove the battery cover . Note: Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 2. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 3. Insert the [...]

The illuminated entry system will turn off the lights if: • the ignition is turned to the on position, or • the integrated keyhead transmitter lock control is pressed, or • the vehicle is locked using the keyless entry keypad (if equipped), or • after 25 seconds of illumination. The lights will not turn off if: • they have been turned on [...]

2. W ithin five seconds press the 1 • 2 on the keypad. The doors will lock and then unlock to confirm that the system is in programming mode. 3. Enter your personal 5–digit code. Each number must be entered within five seconds of each other . 4. Press 1 • 2 on the keypad to assign the Driver 1 setting. The doors will lock and then unlock to c[...]

T o unlock all doors and liftgate, press the 3 • 4 control within five seconds of entering the factory set 5-digit code or your personal code. T o lock all doors and liftgate, press the 7 • 8 and the 9 • 0a tt h e same time. Note: The driver’ s door must be closed. Y ou do not need to enter the keypad code first. T o open the liftgate glass[...]

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster . • When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock 威 system is functioning as a theft deterrent. • When the ignition is in the on position, the indicator will glow for three seconds to [...]

keyless entry transmitter . A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be IKT s with remote entry functionality . If your IKT s or standard SecuriLock 威 coded keys are lost or stolen and you don’t have an extra coded key , you will need to have your vehicle towed to an authorized dealer . [...]

4. After three seconds but within 10 seconds of turning the ignition to the 1 (off) position, insert the second previously coded key into the ignition. 5. T urn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least three seconds, but no more than 10 seconds. 6. T urn the ignition to the[...]

FRONT SEATS W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W ARNING: Before returning the seatback to its original posi[...]

T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that [...]

T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver’ s seat or seatback when t[...]

W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, res[...]

Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater . The seat he[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion. The adjustable head restraints consist of : • a trimme[...]

Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position. W ARNING: The adjustable head restraint is a safety device. Whenever possible it should b[...]

T o reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants o[...]

3. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button. This will ensure that safety belt does not get caught by staying out of the seat back folding path. 4. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. Note: [...]

5. Rotate seatback down into load floor position. Returning the second row seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place and the red seat unlatched indicator on release paddle is not visible. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is loc[...]

W ARNING: Make sure safety belt buckle heads are through elastic holders on seat backs. Safety belt buckles may break if they are trapped underneath the seatback as the seatback is rotated down. W ARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning [...]

T o install the second row cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk o[...]

How does the Personal Safety System™ work? The Personal Safety System can adapt the deployment strategy of your vehicle’ s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM). During a crash, the RCM may activate the safety bel[...]

Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear -facing child seats, this occurs because they are initially sitting very close to the airb[...]

Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’ s body during frontal collisions, and in side collisions and rollovers. This helps increase the effectiveness of the safety belts. In frontal collisions, the safety belt preten[...]

Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: T o reduce the risk of injury , make sure children sit where they can be properly restrained. W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cann[...]

W ARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming[...]

Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow . The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest. Energy Management Feature • This[...]

When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster , is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. Refer to Safety restraints for children or Safety seats for children l[...]

W ARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all safety belts should be checked for proper function. W ARNING: BEL T AND RETRACTOR ASSEM[...]

W ARNING: The driver and front passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in deployment of front airbags, seat-mounted side airbags and Safety Canopy 威 System and safety belt pretensioners. W ARNING: Failure to replace the safety belt as[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position... The safety belt warning light illuminates 1 minute and the warning chime sounds 6 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... Th[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the ve[...]

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during[...]

W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system. Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are deactivated/activated independently [...]

1. T urn the ignition switch to the on position. DO NOT ST ART THE ENGINE. 2. W ait until the safety belt warning light turns off (Approximately 1 minute). • Step 3 must be completed within 30 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, buckle then unbuckle the safety belt three times at a mo[...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; t h e r ei sar i s ko fi n j u r yf r o ma deploying airbag. 4X4 Seating and Safety Restraints 142 201 1 Escape H[...]

W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. W ARNING: The National Highway T raffic Safety Adm[...]

Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. W ARNING: Airbags can kill or injure a child in a child [...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serio[...]

impact sensors, the system wiring, the airbag system readiness light, the airbag backup power and the airbag ignitors). W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is n[...]

The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is off. The indicator lamp is located in the center stack of the instrument panel just above the air vents. Note: The indicator lamp will illuminate for [...]

• If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat. Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small child in child safety seat or booster Lit Disabled Small child with safety belt buckled or unbuckled Lit Disabled Adult Unlit Enabled W ARNING: Even wi[...]

Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. three-ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty seat, or small to medium object with safety belt buckled Lit Disabled If you think that the status of the passenger airbag off indicator lamp is inc[...]

In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat. If ob[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any[...]

How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side air[...]

W ARNING: Several airbag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase th[...]

Safety Canopy 姞 System W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy 威 . Failure to follow these instructions may increase the risk of personal injury in the event of a collision. W ARNING: Do not lean your head on the door . The Safety Canopy[...]

How does the Safety Canopy 姞 System work? The design and development of the Safety Canopy System included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of [...]

The Safety Canopy System is designed to active when the vehicle sustains lateral deceleration sufficient to cause the RCM to initiate safety canopy inflation or when a certain likelihood of a rollover event is detected by the rollover sensor . The safety canopy is mounted to roof side-rail sheet metal, behind the headliner , above the first and sec[...]

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the p[...]

Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to you[...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or tod- dlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Small chil- dren Children who have outgrown o[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lower anchors and top tether anchor) Safety belt only Rear facing [...]

W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age. Follow the child restraint manufacturer’ s instructions and warnings provided for installation and use in conjunction with the ins[...]

training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle. T o locate a child seat fitting station[...]

Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be sea[...]

Perform the following steps when installing the child seat with combination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder b[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

8. Remove remaining slack from the belt. Force the seat down with extra weight, e.g., by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the additional weight of the child is added to the child restraint[...]

LA TCH compatible child safety seats have two rigid or webbing mounted attachments that connect to the two lower anchors at the LA TCH equipped seating positions in your vehicle. This type of attachment method eliminates the need to use safety belts to attach the child seat, however the safety belt can still be used to attach the child seat. For fo[...]

W ARNING: Depending on where you secure a child restraint, and depending on the child restraint design, you may block access to certain safety belt buckle assemblies and/or LA TCH lower anchors, rendering those features potentially unusable. T o avoid risk of injury , occupants should only use seating positions where they are able to be properly re[...]

Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor . T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for in[...]

2. Locate the correct anchor for the selected seating position. There are three tether anchors located on the headliner at the rear of the vehicle. 3. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle. If the tether strap is clipped incorrectly , the child safety seat may not be reta[...]

around four (4) years of age. Consult your child safety seat owner guide for the weight, height, and age limits specific to your child safety seat. Keep your child in the child safety seat if it properly fits the child, remains appropriate for their weight, height and age AND if properly secured to the vehicle. Although the lap/shoulder belt will p[...]

• Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backl[...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

V EHICLE CHARACTERISTICS 4WD system (if equipped) Y our vehicle may be equipped with a four -wheel drive (4WD) system. W ith the 4WD option, power will be delivered to the front wheels and distributed to the rear wheels as needed. This increases traction which may enable you to safely drive over terrain and road conditions that a conventional two-w[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUVs and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile[...]

government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, a[...]

• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a[...]

At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Y ou are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recomm[...]

T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]

the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear . If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety , tires that are damaged or show signs of excessive wear should not be used because they [...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.3[...]

Safety practices Driving habits have a great deal to do with your tire mileage and safety . • Observe posted speed limits • A void fast starts, stops and turns • A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rap[...]

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically . Wheel misalignment in t[...]

• Rear -wheel drive (RWD) vehicles/Four -wheel drive (4WD)/All-wheel drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involve[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA)[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The [...]

When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle. T o restore the full functionality of the tire pressure monitoring system, have th[...]

Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a descrip- tion of how the system functions un- der these conditions, refer to When your temporary s[...]

SNOW TIRES AND CABLES W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death. Add[...]

V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, [...]

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label). Look for “THE COMBINED WEIGHT OF OCCUP ANTS AND CARGO SHOULD NEV[...]

Example only: Tires, Wheels and Loading 200 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus)[...]

Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W [...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . Tires, Wheels and Loading 202 201 1 Escape Hybrid (ehv) Owners G[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.” on your vehicle’ s placard. 2. Determine the combined weight of[...]

to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 [...]

Follow these guidelines to ensure safe towing: • Do not tow a trailer until your vehicle has been driven at least 1,000 miles (1,600 km). • Consult your local motor vehicle laws for towing a trailer . • Refer to the instructions included with towing accessories for the proper installation and adjustment specifications. • Thoroughly prepare [...]

W ARNING: T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury . Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attache[...]

T railer lamps T railer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Do not connect trailer lamps directly to your vehicle’ s tail lamps. This can cause damage to your vehicle’ s electrical system. Contact your authorized dealer or trailer rental agency for pr[...]

T railer towing tips • Practice turning, stopping and backing-up before starting on a trip to get the feel of the vehicle-trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • T o aid in engine/transmission cooling and A/C efficiency during hot weather while stopped in traffic, place t[...]

RECREATIONAL TOWING An example of “recreational towing” is towing your vehicle behind a motorhome. Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. Refer to the Climate Controls chapter for more information. Note: If you tow your vehicle with all four wheels on the ground, follow[...]

STARTING Positions of the ignition 1. Off— locks the gearshift lever and allows key removal. 2. Accessory— allows the electrical accessories such as the radio to operate while the vehicle is not running. 3. On— all electrical circuits operational and warning lights will illuminate. This is the position the key is in when you’re driving. 4. [...]

Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked. Before starting the vehicle: 1. Make sure all vehicle occupants hav[...]

3. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the vehicle 1. T urn the key to 3 (on) without turning the key to 4 (start). If there is difficulty in turning the [...]

Note: If the engine fails to start when it should, which is indicated by the service engine soon light , put the gearshift lever into P (Park), turn the ignition off, then attempt to start the vehicle again. If the vehicle still does not start, it may require refueling, jump starting, resetting of the fuel pump/high voltage shut-off switches or ser[...]

Prior to using the engine block heater , follow these recommendations for proper and safe operation: • For your safety , use an outdoor extension cord that is product certified by Underwriter’ s Laboratory (UL) or Canadian Standards Association (CSA). Use only an extension cord that can be used outdoors, in cold temperatures, and is clearly mar[...]

factory installed block heater system does not have a thermostat; however , maximum temperature is attained after approximately three hours of operation. Block heater operation longer than three hours will not improve system performance and will unnecessarily use additional electricity . Make sure system is unplugged and properly stowed before driv[...]

distance. The ABS will be activated immediately , allowing you to retain steering control during hard braking and on slippery surfaces. However , the ABS does not decrease stopping distance. ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate during start u[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released. W ARNING: If the parking brake is fully [...]

Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL™ (RSC 姞 ) STABILITY ENHANCEMENT SYSTEM The AdvanceT rac 威 with RSC 威 system provides the following stability enhancement features for certain driving [...]

W ARNING: Remember that even advanced technology cannot defy the laws of physics. It’ s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage. Activation of t[...]

When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off. When an event occurs that activates AdvanceT rac 威 with RSC 威 , you may experience the following: • A slight deceleration of the vehicl[...]

or avoiding objects in the roadway . ESC operates by applying brakes to one or more of the wheels individually and, if necessary , reducing engine power if the system detects that the vehicle is about to skid or slide laterally . During electronic stability control events, the stability control light in the instrument cluster will flash. Certain ad[...]

can be restored by pressing the traction control off button again, or by turning off and restarting the engine. If you switch off the traction control, the stability control “OFF” light will illuminate steadily . Pressing the stability control off button again will turn off the stability control “OFF” light. In R (Reverse), ABS and the engi[...]

W ARNING: T railer sway control does not prevent a trailer from swaying, it mitigates the sway from increasing once it has occurred. TSC cannot stop all trailers from swaying. If you are experiencing trailer sway , it is likely that the trailer is improperly loaded for the correct tongue weight or the speed of the vehicle and trailer is too high. P[...]

more effort. Under extreme usage conditions, the steering effort may increase. This occurs to prevent overheating and permanent damage to your steering system. If this should occur , you will neither lose the ability to steer the vehicle manually nor will it cause permanent damage. T ypical steering and driving maneuvers will allow the system to co[...]

W ARNING: Loaded vehicles, with a higher center of gravity , may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slower speeds, avoiding abrupt steering changes and allowing for increased stopping distance, when driving a heavily loaded vehicle. Over -loading or loading the vehic[...]

W ARNING: Do not drive your vehicle until you verify that the brake lamps are working. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the off position and remove the key whenever you leave your vehicle. W ARNING: If the parking brake is fully released, but the brake warning lam[...]

R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle is free to roll; hold the brake pedal down while in this position. Because of the unique nature of the hybrid vehicle, the[...]

REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. W ARNING:[...]

The RSS detects obstacles up to 6 feet (1.8 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound con[...]

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rearview camera system located on the liftgate provides a video image, which appears in the rearview mirror or on the navigation screen (if equipped), of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle. T o use the camera, place the transmission in[...]

Note: The default setting for the camera delay is off. Press the “Settings” button found on the navigation screen (if equipped) to set the camera delay feature to on or off. When towing, the camera will only see what is being towed behind the vehicle; this might not provide adequate coverage as it usually provides in normal operation and some o[...]

• If the image is not clear , then check if there is anything covering the lens such as dirt, mud, ice, snow , etc. If the image is still not clear after cleaning, have your camera inspected by your authorized dealer . ACTIVE PARK ASSIST (AP A) (IF EQUIPPED) Active park assist (AP A) will detect an available parallel parking space and automatical[...]

For best performance, the driver should drive the vehicle as parallel as possible while passing a parking space. If driven too fast (above 18 mph [30 km/h]) for the system to measure parking spaces, the message center will display ACTIVE P ARK REDUCE SPEED. When the system has found a space, the message center will display SP ACE FOUND PULL FORW AR[...]

When you determine the vehicle is back far enough or you hear a solid tone from reverse sensing system, bring the vehicle to a complete stop and move the gearshift to D (Drive). The message center will now display PULL FORW ARD USE CAUTION followed by a chime. When you determine the vehicle is far enough forward or a solid tone from forward sensing[...]

• Exceeding a vehicle speed of 6 mph (10 km/h) during automatic steering • Deactivating the AdvanceT rac 威 system or the system has activated on a slippery or loose surface • ABS activation or failure • Any door (except the driver’ s door) opens • Something touching the steering wheel. If a fault is present in the system, the message [...]

Why doesn’ t APA position the vehicle where I want in the space? • The driver allows the vehicle to roll in the opposite direction of the transmission, such as rolling forward when R (Reverse) gear is selected. • Y ou may be driving in R (Reverse). AP A can only look for a parking space while moving forward. • There may be an irregular curb[...]

Driving with blind spot mirrors Before a lane change, check the main mirror first, then check the blind spot mirror . If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you are going to change lanes. Glance over your shoulder to verify traffic is clear , and carefully change l[...]

Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow , mud and rough terrain and have operating characteristics that are somewhat different from conventional vehicles, both on and off the road. How your vehicle differs from other vehicles T ruck and utility vehicles can differ from some othe[...]

sideways out of control or roll over . Remember , your safety and the safety of others should be your primary concern. W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for corner[...]

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more. Additionally , smooth variations of [...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et[...]

slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer . If you do stall ou[...]

A void sudden braking as well. Although a 4WD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster , because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehicles for stoppi[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the period of five years or 60,000 miles[...]

Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arr[...]

HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Press the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use [...]

The fuel pump shut-off switch is located in the front passenger’ s footwell, behind a flip-up cover . The high voltage shut-off switch is located in the cargo area on the passenger side of the vehicle in the jack compartment, behind the jack access door . The switch is located behind the jack. T o reset the switch(es): 1. T urn the ignition to th[...]

If you see or smell fuel, do not reset the fuel pump shut-off or try to start your vehicle; you could injure yourself or others. Have all the passengers get out of the vehicle and call the local fire department or a towing service. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are[...]

Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuse cover . Press the tabs on the top and bottom of the fuse cover to remove. The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A 110V invert[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 4 30A Moon roof 5 10A Brake-shift i nterlock (BSI), Passenger compartment fuse panel, Keypad illumination 6 20A T urn signals, Stop lamps 7 10A Low beam headlamps (left) 8 10A Low beam headlamps (right) 9 15A Interior lights 10 15A Backlighting 11 10A Four wheel drive 12 7.5A Power mirror switc[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 32 10A Rear video camera module 33 10A Not used (spare) 34 5A Not used (spare) 35 10A Four wheel drive, Electronic power assist steering (EP AS), 110V inverter module, Park aid module, Active park assist module 36 5A Passive anti-theft system (P A TS) transceiver 37 10A Not used (spare) 38 20A [...]

W ARNING: Always disconnect the low voltage (underhood) battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the low voltage (underhood) battery or refilling fluid reservoirs. If the low voltage (underhood) battery has been disconnected[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 6 — Not used 7 15A* Liftgate latch 8 5A* T raction battery control module 9 50A** Brake control module 10 30A** Front wipers 11 — Not used 12 40A** Blower motor 13 — Not used 14 10A* Heater/Coolant pump 15 50A** T raction battery control module (TBCM) 16 40A** Cooling fan 1 17 40A** Cooli[...]

Fuse/Relay Location Fuse Amp Rating Protected Circuits 29 15A* PCM power 30A — Cooling fan 1 relay 30B — Electric vacuum pump mechanical relay 30C — Cooling fan main relay 30D — Cooling fan 2 relay 31A — Reverse lamp relay 31B — Not used 31C — Heater pump relay 31D — Coolant pump relay 31E — Not used 31F — Liftgate latch relay 3[...]

Auxiliary relay box The relay box is located in the engine compartment on the radiator support bracket. Fuse/Relay location Fuse amp rating Description Relay — Electric vacuum pump (solid state) 1 — Not used 2 — Not used 3 — Not used 4 5A* V acuum pump monitor 5 — Not used 6 — Not used * Mini fuses **Cartridge fuse CHANGING THE TIRES If[...]

Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. T o restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. Have a flat serviced by an authorized dealer in order to prevent damage to the TPM[...]

When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • T ow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • [...]

When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • T owing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible. Stopping and securing t[...]

T o remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first. Remove the lug wrench from the jack in order to remove the spare tire from under the vehic[...]

If equipped with a tether , perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether . 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached fastener[...]

W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. W ARNING: If the vehicle slips off the jack, you or someone else could be seriously injured. W ARNING: Do no[...]

Before placing the jack under the vehicle, NOTE the jack locations: • Front View shown from rear of front tire. Position the jack directly below the protruding bolt. Roadside Emergencies 264 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus)[...]

• Rear View shown from forward of rear tire. Position the jack directly below the stud on the rear trailing arm. 3. Position the jack according to the guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Be sure to place the jack away from the rear edge of the rocker to avoid damaging the rear ti[...]

Never use the differentials as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 4. Remove the lug nuts with the lug nut wrench. 5. Replace the flat tire [...]

• guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in[...]

4. Slide the wheel partially under the vehicle and install the retainer through the center of the wheel. 5. T urn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The effort to turn the jack handle increases significantly as the tire contacts the frame. The spare tire carrier will ratchet when the [...]

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger . DO NOT ap[...]

Preparing your vehicle If your low voltage (underhood) battery becomes disconnected or disabled for any reason, the vehicle controller must relearn the engine’ s operating characteristics in order to operate it at maximum efficiency . This relearning process occurs the first time the vehicle is driven after reconnecting the low voltage battery . [...]

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable [...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle’ s [...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not a[...]

Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Emergency towing In case of a roadside emergency with a disabled vehicle ([...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In some states, you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by sta[...]

In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126 Y ou are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies co[...]

for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim f[...]

GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than[...]

If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P .O. Box 21470 Dubai, United Arab Emirates T elephone: +971 4 3326084 F AX: +971 4 3327299 Email: menacac@ford.com www .me.fo[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • [...]

• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Y our authorized dealer has touch-up paint to match your vehicl[...]

• Spray Motorcraft 威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft 威 Engine Shampoo (CXC-66-A). • Cover the highlighted areas to prevent water damage when cleaning the engine. Note: As with all transmissions, be especially careful as water entry into the vents can[...]

vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. T o clean these items, follow these ti[...]

• Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately . Damage may not be covered by your warranty . W ARNING: Do not use chemical solvents or strong [...]

W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. W ARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a colli[...]

For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. • Clean spills as quickly as possible. • T est any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather . • Do not spill coffee, ketchup, mustard, oran[...]

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Eac[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide to find out which parts and services are covered. Use only r[...]

The following are specific locations in the rear cargo area that consist of high voltage components and/or wiring. 1. High voltage connector shield 2. Service disconnect 3. High voltage battery case 1 2 3 Maintenance and Specifications 292 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus)[...]

Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels. W ARNING: T o reduce the ris[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low voltage (underhood) battery 7. Engine air filter assembly 8. Engine oil dipstick 9. W indshield washer fluid reservoir Maintenance and Specificat[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smea[...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be impr[...]

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. T o replace the wiper blade: 1. Grab the wiper arm with one hand close to the arm/blade joint and pull it as far away from the glass as possible. Do not use excessive force because it can[...]

5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within the lower and upper holes/lines, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole/line, engine oil must be added to raise the level withi[...]

T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level dipstick and/or the engine oil filler cap removed. Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark[...]

It is recommended you use the appropriate Motorcraft 威 oil filter or another with equivalent performance for your engine application. LOW VOLTAGE (UNDERHOOD) BATTERY Y our vehicle is equipped with a Motorcraft 威 maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shie[...]

W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medi[...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. Low and high voltage battery – storage Y our vehicle must be started and run for a minimum of 10 minutes once a month in order [...]

Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information . The coolant concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer o[...]

Checking motor/electronics (M/E) coolant The M/E coolant reservoir is located behind the engine coolant reservoir . Refer to the following engine coolant sections for all information, instructions and warnings related to cooling systems. The two systems use the same coolant and operate similarly , with the Motor and Electronics system generally ope[...]

If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty . If the reservoir is low or empty , add engine coolant to the reservoir . Refer to Adding engine coolant in this chapter . Note: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield w[...]

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolan[...]

If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your authorized dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company does NOT recommend [...]

• A coolant concentration of 40% will provide freeze point protection down to -12°F [-24°C]. Decreased engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage. • If available, refer to the chart on the coolant container to ensure the coolant concen[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to th[...]

Choosing the right fuel Use only UNLEADED fuel or UNLEADED fuel blended with a maximum of 10% ethanol. Do not use fuel ethanol (E85), diesel, methanol, leaded fuel or any other fuel. The use of leaded fuel is prohibited by law and could damage your vehicle. Y our vehicle was not designed to use fuel or fuel additives with metallic compounds, includ[...]

performance and emission control system protection for your vehicle. Gasolines that meet the W orld-W ide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the W orld-W ide Fuel Charter . Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality , per the rec[...]

1. Locate the white plastic funnel. It is attached to the inside of the rear passenger side cargo compartment access door . 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your auth[...]

Filling the tank When the fuel gauge indicates empty , there is still a small reserve of fuel in the fuel system. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. The amount of usable fuel[...]

Driving style — good driving and fuel economy habits Since it is able to operate in electric mode and to collect braking energy , your hybrid vehicle may get better fuel economy in city driving than on the highway . This is contrary to conventional vehicles. However , many of the same actions that improve fuel economy in a conventional vehicle wi[...]

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 300 lb [136 kg] of weight carried). • Adding certain accessories to your vehicle (for example; bug deflectors, rollbars/light bars, running boa[...]

smoke or loss of engine power could indicate that the emission control system is not working properly . An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately . W ARNING: Exhaust leaks may result in entry of harmful and potent[...]

indicator should stay off the next time the engine is started. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity . Although some malfunctions detected by th[...]

engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, the above driving cycle will have to be repeated. BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components ar[...]

W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Release the clamps that secure the air filter housing cover . 2. Carefully separate the two halves of the air filter housing. 3. Remo[...]

General • Store all vehicles in a dry , ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to protect against rust and damage. Body • W ash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear -wheel housing and underside of front fend[...]

Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level. Confirm there are no cooling system leaks, and fluid is at the recommended level. Battery • Check and recharge as necessary . Keep connections clean. • If storing your vehicle for more than 30 days without recharging the [...]

• If the battery was removed, clean the battery cable ends and inspect. If you have any concerns or issues, contact your authorized dealer . MOTORCRAFT PART NUMBERS Component 2.5L I4 engine Oil filter FL-910 Spark plugs 1 Engine air filter element F A-1772 Cabin air filter FP-66 Low voltage (underhood) battery BXT -96R 1 For spark plug replacemen[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Brake fluid Between MIN and MAX lines on reservoir Motorcraft 威 High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 Body hinges, latches, door striker plates and rollers, seat tracks[...]

Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine oil 5.3 quarts (5.0L) • Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) • Motorcraft 威 SAE 5W -20 Full Synthetic Motor Oil (US) • Motorcraft 威 SAE 5W -20 Super Premium Motor Oil (Canada) • Motorcraft 威 SAE 5W -20 Synthetic Motor Oi[...]

Item Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification W indshield washer fluid Fill as required Motorcraft 威 Premium W indshield W asher Concentrate (US) Premium Quality W indshield W asher Fluid (Canada) ZC-32-A (US) CXC-37-(A, B, D, and F) (Canada) / WSB-M8B16-A2/- - Fuel tank 15 gallons (56.8L) —— 1 Add the coola[...]

ENGINE DATA Engine 2.5L I4 engine Cubic inches 152 Required fuel 87 octane Firing order 1-3-4-2 Ignition system Coil on plug Spark plug gap 0.049–0.053 inch (1.25–1.35mm) Compression ratio 12.3:1 Engine drivebelt routing HIGH VOLTAGE BATTERY DATA High voltage battery Battery chemistry Nickel metal hydride Nominal voltage 330 volts Battery syste[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSIO[...]

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehic[...]

Lifestyle • Ash cup / smoker’ s package • Roof racks and carriers* • Cross bars • Rear bumper protector* • Navigation* • Cargo net* • SUV camping net* • Cargo organization and management Peace of mind • Keyless entry keypad • W indshield wiper shaker* • Wheel locks • Back up camera* • V ehicle tracking and recovery* • [...]

• Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use. • T o avoid interference with other vehicle functions, such as anti-lock braking systems, amateur radio users who install radios and antennas onto their vehicle should not locate the Amateur Radio Antennas i[...]

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Compo[...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 336 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus)[...]

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) Y ou can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company . Depending on the plan you purchase, Ford ESP provides benefits such as: • Rental reimbursement • Coverage for certain maintenance and w[...]

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it. It is y[...]

Ford strongly recommends the use of genuine Ford replacement parts. Parts other than Ford, Motorcraft 威 or Ford-authorized remanufactured parts that are used for maintenance replacement or for the service of components affecting emission control must be equivalent to genuine Ford Motor Company parts in performance and durability . It is the owner[...]

Factory-trained technicians Ford and Lincoln Mercury service technicians participate in extensive factory-sponsored certification training to help them become experts on the operation of your vehicle. Ask your dealership about the training and certification their technicians have received. Genuine Ford and Motorcraft 姞 replacement parts Ford and [...]

Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help ensure your ve[...]

Be sure to ask your Ford or Lincoln Mercury dealership service advisor or technician about the multi-point vehicle inspection. It’ s a comprehensive way to perform a thorough inspection of your vehicle. It’ s your checklist that gives you immediate feedback on the overall condition of your vehicle. Y ou’ll know what’ s been checked, what’[...]

Scheduled Maintenance Guide 343 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing USA (fus)[...]

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule is presented at specific mileage (kilometer) intervals with exceptions noted. Reset your oil life monitoring system after each engine oil and filter change; refer to the Instrument Cluster chapter . Scheduled Maintenance Guide 344 201 1 Esca[...]

Miles (x 1,000) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Kilometers (x 1,000) 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 Months 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • ••••?[...]

Every 20,000 miles (32,000 km) Replace cabin air filter (if equipped) Every 30,000 miles (48,000 km) Replace climate-controlled seat filter (if equipped) Replace engine air filter Every 100,000 miles (160,000 km) Change engine coolant and motor/electronics coolant 1 Replace spark plugs Inspect accessory drive belt(s) 2 Every 150,000 miles (240,000 [...]

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below , you will need to have some items maintained more frequently . If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance[...]

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently , service as required – Replace cabin air filter (if equipped). – Replace engine air filter . Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) – Change engine oil and replace oil filter . Every 5,000 miles (8,000 km) – Inspect[...]

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-design axles are lubricated for life. These lubricants are not to be checked or changed unless a lea[...]

COOLANT CHANGE RECORD Engine coolant ❑ 6 years or 100,000 miles (160,000 km) - change engine and motor/electronics coolant (whichever comes first). ❑ After initial change - change engine and motor/electronics coolant every 3 years or 50,000 miles (80,000 km). Scheduled Maintenance Guide 355 201 1 Escape Hybrid (ehv) Owners Guide, 1st Printing U[...]

Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H[...]

A Accessory delay .......................... 77 Active Park Assist .....................233 AdvanceT rac .............................. 219 Air cleaner filter ....... 320–321, 324 Air conditioning automatic temperature control system ..........................52 Airbag supplemental restraint system ........................142, 151, 154 and child [...]

Child safety seats ......................162 attaching with tether straps ....................................... 169 in front seat ............................ 163 in rear seat .............................. 163 LA TCH ..................................... 166 recommendations ................... 160 Child safety seats - booster seats .............[...]

filter , specifications ........ 299, 324 recommendations ................... 299 refill capacities ........................ 325 specifications .......................... 325 Event data recording .................. 13 Exhaust fumes .......................... 214 F Fleet MyKey programming ........ 96 Floor mats ................................... 90[...]

J Jack ............................................ 257 positioning ............................... 257 storage ..................................... 257 Jump-starting your vehicle ...... 269 K Keyless entry system autolock ........................... 101, 103 keypad ..................................... 109 locking and unlocking doors ............[...]

Parts (see Motorcraft 威 parts) ........... 324 Passenger Occupant Classification Sensor ................. 129 Power distribution box (see Fuses) ............................... 253 Power door locks ...................... 101 Power mirrors ............................. 78 Power point ................................. 74 Power steering ............[...]

Snowplowing ............................... 12 SOS Post Crash Alert ............... 157 Spark plugs, specifications .....................324, 328 Special notice ambulance conversions ............ 12 utility-type vehicles .................. 12 Specification chart, lubricants ................................... 325 Speed control .....................[...]

W W arning lights (see Lights) ....... 18 W asher fluid .............................. 295 W ater , Driving through ............. 245 W indows power ......................................... 76 rear wiper/washer ..................... 70 W indshield washer fluid and wipers .......................................... 69 checking and adding fluid .....[...]