InFocus SP8600 manual

[...]

Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r. © Copyright 2010 Disclaimer The information in this document is su[...]

SP8600 User's Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector. Keep this manual for future reference. Symbols Used Warning symbols a re [...]

Preface Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically. ¾ Allow at least 50 cm clearance around th e exhaust ven[...]

SP8600 User's Manual Replacing the Lamp Replacing the lamp can b e hazardous if done in correctly. See Replacing the Proje ction Lamp on page 29 for clear and safe instructi ons for this procedure. Before replacing the lamp: ¾ Unplug the power cord. ¾ Allow the lamp to cool for about one hour. Cleaning the Projector ¾ Unplug the power cord [...]

Preface – v – Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST .........................................................................................................................[...]

SP8600 User's Manual — vi — SPECIFICATIONS ............................................................................................................................................................. 39 S PECIFICATIONS .........................................................................................................................[...]

SP8600 User's Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJECTOR R EMOTE CONTR OL ( BATTERY NOT INCLUDED ) HDMI CABLE P OWER CORD (EU) P OWER CORD (UK) P OWER CORD (US) CD-ROM (T HIS U SER ’ S MANUAL ) Q UICK S TART C ARD W ARRANTY C AR D Safety[...]

SP8600 User's Manual Views of Projector Parts Front-right View 1 34 5 6 7 2 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Height-adj uster butto n Push to release height adjust er 2. Height adjuster Adjust level of projector 12 3. Lens Projection Lens 4. IR receiver Receive IR sign al from rem ote control 6 5. Focus ring Focus the projected image [...]

SP8600 User's Manual Top view—On-screen Display (OSD) buttons and LEDs Source Menu Enter Re-sync 11 10 12 1 2 4 5 6 3 7 8 9 I TEM L ABEL D ESCRIPTIO N S EE PAGE : Green Power On / Standby 1. Power LE D Off Power Off (AC Off) Red Lamp is ready to be powered-on. 2. Lamp LED Lamp is not ready (warm ing up/ shutti ng down/c ooling) (see Flashing[...]

SP8600 User's Manual Rear view 12 3 4 5 6 7 8 9 1 0 11 12 13 14 15 16 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 11 1. AC IN Connect the power cord 2. Connect a USB cable from a computer (USB) 3. COMPONENT Connect a compone nt video enable d device 4. S-VIDEO Connect a S-VIDEO cable from a vi deo device – 4 – 5. COMPOSITE Connect a COMPOSITE c[...]

SP8600 User's Manual Bottom view 51.5 65.0 71.0 90.5 109.0 76.0 2 1 3 4 2 Ceiling Mount M4x8 (Max L=12mm) I TEM L ABEL D ESCRIPTION S EE PAGE : 12 1. Tilt adjustor Rotate adju ster lever to adjust angle po sition. 2. Ceiling support ho les Contact your dealer for information on mounting the projector on a ceiling 3. Height adjustor Adjuster dr[...]

SP8600 User's Manual Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector. If the path be- tween the remote control and the [...]

SP8600 User's Manual – 7 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Up cursor Navigate and c hange settings in the OSD 2. Enter Change settings in the OSD 15 3. Power Turn the projector O n or Off 11 4. Right curs or Navigate and c hange settings in the OSD 15 5. Volume + Increase volume 6. Volume - Decrease volume 14 7. Mute Mute the bui[...]

SP8600 User's Manual – 8 – Remote Control Operating Range The projector receives infrared signals from the remote control. It is not necessa ry to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of abou[...]

SP8600 User's Manual – 9 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) . 2. Insert the battery (not included) with the positive side facing up. 3. Replace the cover. Caution: 1. Only use a 3V lithium batt[...]

SP8600 User's Manual Connecting Input Devices A PC or note book computer and video devices can be connected to the projector at the same time. Video devices include DVD , VCD, and VHS players, as we ll as movie camc orders and digi tal still camera s. Check the user manu al of the connectin g device to confir m it has the appropriate output co[...]

SP8600 User's Manual Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED will be on. 2. Turn on the connected devices. 3. Ensure the POWER LED displays a solid green and not a flashing green. Then press the POWER button to turn on the projector. The projec[...]

SP8600 User's Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it is perpendicular t o the screen. • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle. • E[...]

SP8600 User's Manual Adjusting the Zoom ring, Focus and Keystone – 13 – 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size B . 2. Use the Image-focus control (on the projector only) to sharpen the pro- jected image . A 3. Source Menu Enter Re-sync Use the KEYSTONE buttons (on the projector[...]

SP8600 User's Manual Adjusting the Volume 1. Source Menu Enter Re-sync Press the Volume +/- buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/- . 3. Press the MUTE button to turn off the volume (This feature is available only on the remote). – [...]

SP8600 User's Manual – 15 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control curs or buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The foll[...]

SP8600 User's Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic . 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is selected. 4. Pre[...]

SP8600 User's Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 17 –[...]

SP8600 User's Manual PICTURE>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◄► to change values for settings. Note: Customizing the settings in PICTURE>>Bas[...]

SP8600 User's Manual PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Noise Reduction Press t[...]

SP8600 User's Manual HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to set the Primary Color. Notes: There are six s ets ( R / G/ B/ C/ M/ Y) of colors to be custom ized. Primary Color Hue Press the ◄► buttons to adjust the Hue. Saturation Press the ◄► buttons to[...]

SP8600 User's Manual DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Press the cursor ◄► button to set the Aspect Ratio. (Range: Auto / [...]

SP8600 User's Manual PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected. I TEM D ESCRIPTIO N Press the ENTER/AU TO button on the control panel or the ENTER/AUTO button on the remote co[...]

SP8600 User's Manual SETUP>> Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings. I TEM D ESCRIPTIO N Language Press the cursor ◄► butt[...]

SP8600 User's Manual Menu Settings Press the ENTER button to enter the Menu Settings sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Position Press the ◄► buttons to set the Menu Display timer before the OSD times out. (Range: 5sec/ 10se[...]

SP8600 User's Manual SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu. I TEM D ESCRIPTIO N – 25 – Audio Press the ENTE R bu tton to enter the Audio sub me nu. S[...]

SP8600 User's Manual Audio Press the ENTER button to enter the Audio sub menu. I TEM D ESCRIPTIO N Volume Press the ◄► buttons to adju st the audi o Volum e. Bass Press the ◄► buttons to ad just the audi o Bass. Treble Press the ◄► buttons t o adjust t he audio Tr eble. Mute Press the ◄► buttons to turn on o r off the s peaker.[...]

SP8600 User's Manual HDMI Press the ENTER button to enter the HDMI sub menu. I TEM D ESCRIPTIO N Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Form at HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain. Closed Caption Press the ENTER button to enter the Closed Ca[...]

SP8600 User's Manual STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu . I TEM D ESCRIPTIO N Source Displays the activated input source. Resolution Displays the current resolution of input source. Lamp Hour Displays the number of hours th e lamp has been in use. Firmware Vers ion [...]

SP8600 User's Manual – 29 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this produc t contains a small amount of mercury.[...]

SP8600 User's Manual 3. Remove the lamp compart- ment cover. 4. Remove the three screws from the lamp module. 5. Lift the module handle up. 6. Pull firmly on the module handle to remove the lamp module. – 30 –[...]

SP8600 User's Manual 7. Reverse steps 1 to 6 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be con- nected properly before tightening the screws. – 31 –[...]

SP8600 User's Manual – 32 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow w[...]

SP8600 User's Manual Using the Kensingt on ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable. The security lock corresponds to Kensington’s Micr oSaver Security Syste[...]

SP8600 User's Manual – 34 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose c[...]

SP8600 User's Manual – 35 – LED Error Messages E RROR C ODE M ESSAGES P OWER LED B LINK L AMP LED B LINK T EMP LED B LINK Lamp Ready ON ON OFF Start (AC Power standby) ON OFF OFF Cooling ON flashing OFF Over Temperat ure OFF OFF ON Thermal Break Sensor error 4 blinks 4 blinks OFF Lamp error 5 blinks OFF OFF Lamp End of l amp life detect ed[...]

SP8600 User's Manual – 36 – Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. Lamp Problems Problem: There is no light from the projecto[...]

SP8600 User's Manual – 37 – Audio Problems Problem: There is no sound 1. Adjus t the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced. Problem: The sound is distorted 1. Check the audio cable conne[...]

SP8600 User's Manual – 38 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables. ․ Standard (or “category 1”) HDMI cables have be en tested to perform at speed s of 75Mhz o[...]

SP8600 User's Manual – 39 – S PECIFICATIONS Specifications SP8600 Model Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Weight 3.4 kg (7. 5 lbs) Projection distance 1 meters ~ 10 meters Projection screen size 30" ~ 30 0" Projection lens Manual Focus/ Manual Zoom Zoom ratio 1.2 Vertical keystone correc tion +/- 30 de[...]

SP8600 User's Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table – 40 – 16:9 SCREEN PROJECTION DISTANCE DIAGONAL WIDTH HEIGHT INCH MM MM MM MIN LENGTH (WITH MAX ZOOM) AVERAGE MAX LENGTH VERTICAL OFFSET IN MM (WITH MIN ZOOM) 30 762 664 374 1056 1162 1267 56 40 1016 886 498 1408 1549 1690 75 50 1270 1107 623 1[...]

SP8600 User's Manual – 41 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) NTSC — 15.734 60.0 O — － － PAL/SECAM ?[...]

SP8600 User's Manual – 42 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.5 60.0 — O — O HDTV 1080p 56.3 50.0 — O — O O: Frequency supported —[...]

SP8600 User's Manual Projector Dimensions 326 mm 254 mm 104 mm 98 mm – 43 –[...]

SP8600 User's Manual – 44 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial env[...]