JVC LST1006-002A manual

Card Printer CX-7000 Series Electronic Manual Thank you for purchasing this product. Please read through this “Electronic Manual” carefully in advance to ensure proper use of the product. Also, to make sure that the product is used safely, please read through the “Safety Precautions” in the “READ ME FIRST” booklet. Please store the manu[...]

Contents Before Use About this Manual ................................................................ 3 Precautions .......................................................................... 3 Disclaimer ............................................................................ 7 Name and Functions of Parts ......................................[...]

About this Manual Contents of this Manual v The copyright of this manual belongs to our company. Reprint and duplicate of this manual in part or full without the prior consent of our company is strictly prohibited. v Product names of other companies described in the manual are the trademarks or registered trademarks of the respective companies. Sym[...]

Warnings . . . Before Use 4[...]

Caution . . Before Use 5[...]

Precautions During Use v Please read through all the following items before using the printer. Printer Installation v When the printer is not in use, it is recommended that you turn off the power, and use a cover that is large enough to cover up the entire printer unit. v Do not place the printer unit in the following locations. Doing so may have a[...]

Disclaimer . Name and Functions of Parts Internal Mechanism Diagram . A Card feeder unit v This is the roller for feeding cards. B Bend remedy unit (optional) v Corrects bending of the card after retransfer. C Retransfer heating roller v Transfers images printed on the retransfer film to the card. D Non-contact IC encoder (optional) v Writes data t[...]

Front . A Sliding knob v Opens/closes the printer door. v Slide it upward, and pull toward you to open the printer door. B Operation buttons v For selecting and confirming information on the operation panel. C Operation panel v Displays the settings, operating status, and error messages. D Card hopper v For loading cards. E Printer door F Power swi[...]

When Printer Door is Open . A Card feed roller shaft v When a card jam occurs, attach a jog dial to turn the card feed roller. B Card turn over unit shaft v When a card jam occurs, attach a jog dial to turn the card turn over unit. C Cleaning unit v Removes dust or dirt attached to the card. D Cleaning roller shaft v When a card jam occurs, attach [...]

Specifications Main Specifications Item Description Recording system Dye sublimation retransfer Paper feed mode Automatic Recording density 300 dpi Reproduction gradation 256 levels each for Y, M and C 2 levels for Resin K Interface USB2.0(Hi-speed/Full Speed) Ethernet(100BASE-TX/10BASE-T) Operating environment conditions Temperature: 15 ° C to 30[...]

Options Options v Bend remedy unit Device for correcting card bend after printing. v Magnetic encoder Device for writing data to a magnetic stripe card. It can only be installed on a double-sided printer. v Contact IC encoder Device for writing data to a contact IC card. v Non-contact IC encoder Device for writing data to a non-contact IC card. Bef[...]

Printing a Card Cautions: v If you see an [Initializing..] or [Preheating..] message on the LCD panel of the printer, this means the printer is not ready yet. Printing cannot be performed until a [Ready] massage appears. v Printing the card on the side with the magnetic stripe may cause printing errors or damage to the card’s functions. If you wa[...]

Operation Panel Name and Functions of Parts . Ready To t al Reset Menu *** A B C A Operation panel v Displays the settings, operating status, and error messages. B Status icon/operation button display v Displays the status icon and function of the operation button. C Operation buttons v For selecting a button function displayed on the operation pan[...]

Operation Panel Operation Display Background color Changes according to the printer’s operating status. v During startup Bright green v Under normal circumstances Sky blue v During initialization using K , during test printing using the operation panel, cleaning, downloading and during security lock setting using the operation panel Light purple [...]

Setting Mode v Settings can be viewed on the printer’s operation panel. v Settings can be changed on the status monitor of the computer. "Setting Using the Operation Panel" ( A page 22) "Sequence of Setting Modes" ( A page 17) "Factory Settings" ( A page 19) Cleaning v For setting during cleaning of the card feed rol[...]

Bend Remedy v Displays the bend remedy mode settings. Settings v Temp Level: -5, -4, -3, -2, -1, 0, Off For setting the bend remedy heating roller temperature. Selecting a larger value increases the temperature. If the printer is not reset after changing the temperature setting, temperature is adjusted after the printing operation starts. v Speed: [...]

Sequence of Setting Modes v Settings can be viewed on the printer’s operation panel. v Settings can be changed on the status monitor of the computer. "Setting mode" ( A page 15) 1 Press I v Enters the setting mode. . 2 Press J v Pressing it each time displays the next setting item. v Pressing G displays the setting item on the next lowe[...]

. . . . . . . Operating the Printer 18[...]

Factory Settings m Media Item Factory Settings Ink Type - Film Type 1000 Card Thickness Standard m Print Item Factory Settings YMC Level 0 Black Level 0 Black Mode Standard UV Level 3 PO Level 0 m Retransfer Item Factory Settings Temp Level 1 Speed (Front) 2 Speed (F-UV) 2 Speed (Back) 2 Speed (B-UV) 2 MG Peel Mode Standard Standby Mode Front Wait [...]

Security Lock v The security lock function can be applied to the printer door and card hopper to prevent opening of the printer door as well as removal of cards. v The lock can be turned on/off using the status monitor on the computer. "Status monitor" ( A page 117) v By registering a security key number on the printer unit, you can turn [...]

Deactivating the Security Lock v When a security lock is turned on, you can deactivate it as follows. 1 Press the operation button (center) for at least three seconds v A [Unlock Sec-Key OK?] message appears. . 2 Press B v A [Key for unlock] message appears. . 3 Enter the registered security key number . v Pressing A each time advances to the next [...]

Setting Using the Operation Panel Initialization v Whenever the power is turned on, cue (initialization) is performed automatically on the ink ribbon and retransfer film. v You can also perform initialization manually using the operation button on the operation panel. 1 Press K v An [Initialize OK?] message appears. . 2 Press B v An [Initializing..[...]

m Initializing printer after feeding by two images A Press J to set to [2'nd Panel, OK?] . B Press B v An [Initializing..] message appears, and the printer is initialized after feeding the ink ribbon and retransfer film by two images. . Test Print v Prints the printer’s built-in test pattern, or the different settings. v The printer unit can[...]

Firmware Update 1 Press I v A [Cleaning] message appears. . 2 Press J to set to [Download] v Pressing it each time displays the next setting item. . 3 Press G v A [Download Ready] message appears, indicating that the printer is ready to download data from the computer. . . 4 Start data download from the computer v A [Downloading..] message appears.[...]

Display Mode Setting v This is used for setting the information to be displayed on the operation panel. Settings v Counter: Displays the counter preset in "Counter setting". v Laminator State: Displays the operating status of the connected laminator. If a laminator is not connected, the counter is displayed. 1 Press I v A [Cleaning] messa[...]

6 Press F v Enters the settings change mode. . 7 Press A and select a setting 8 Press B to confirm the setting v Pressing B confirms the setting and returns you to the previous screen. 9 Press H to exit the setting mode v Pressing it each time displays the setting item on the next higher level. Counter Reset v This is used to reset the free counter[...]

Contrast Setting v For setting the contrast of the operation panel display. Settings v -3, -2, -1, 0, 1, 2, 3 Selecting a larger value increases the contrast. 1 Press I v A [Cleaning] message appears. . 2 Press J to set to [Setting] v Pressing it each time displays the next setting item. . 3 Press G v A [Display] message appears. . 4 Press G v A [M[...]

Buzzer Setting v For setting whether to sound the buzzer when an error occurs or when settings are changed. Settings v On: turns on buzzer sound, Off: turns off buzzer sound 1 Press I v A [Cleaning] message appears. . 2 Press J to set to [Setting] v Pressing it each time displays the next setting item. . 3 Press G v A [Display] message appears. . 4[...]

Transport Mode Setting v When transporting or moving the printer, ensure that the heating roller is fastened to a safe position. Cautions: v Make sure that you set to the transport mode when transporting or moving the printer. Failure to do so will cause the printer to malfunction. 1 Open the printer door . 2 Press and hold down the cassette button[...]

Setting Using the Status Monitor "Status Monitor Settings" ( A page 107) Operating the Printer 30[...]

Cards Cards have Run Out v Replenish the cards. v The card hopper is able to store up to about 100 cards with a thickness of 0.76 mm. Cautions: v Get ready cards that are designated by the authorized dealer. v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Do not touch the printing surface of [...]

Ink Ribbon Ink Ribbon has Run Out v Replace with a new ink ribbon. Cautions: v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Stand the cassette on a flat surface as illustrated in the diagram. Avoid doing so on the floor as dust attached to it may cause printing errors. . v Do not touch the i[...]

6 Press K N B to reset the printer . Memo: v To avoid printing errors, it is recommended that you forward by one or two images after installing the ink ribbon cassette or retransfer film cassette. "Initializing printer when installing the cassette" ( A page 22) Retransfer Film Retransfer Film has Run Out v Replace with a new retransfer fi[...]

3 Install a new retransfer film v Install while referring to the indication on the label of the cassette. A When installing the retransfer film, make sure that at least three black lines are wound onto the take-up side. . B With the retransfer face facing outward, align the unused side of the film with the arrow on the cassette, and unwind it along[...]

Servicing of Parts m Request for routine servicing v In order to prevent printing errors and malfunctions from occurring in advance, please request for routine servicing by the servicing personnel. For details on servicing, please consult our authorized dealers. Cleaning Roller v The function of the cleaning roller is to remove any dirt or dust att[...]

Card Load Roller v Card jams may occur if the card load roller is dirty. Cautions: v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Start work after ensuring that the power has been turned off. v After cleaning is complete, check to ensure that all dismantled parts are restored to their origin[...]

Card Feed Roller/Heating Roller v The color of the printed card may appear faded or dirt may appear conspicuous if the card feed roller or heating roller is dirty. v Perform cleaning after printing about 1,000 cards. Cautions: v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Before cleaning th[...]

9 Press B v A [Cleaning..] message appears. . Cautions: v If the retransfer heating roller is hot, a [HR is too hot!] message will be displayed. Turn off the power, and perform cleaning after the retransfer heating roller has cooled down completely. . 10 Insert the cleaning card (sold separately) within 20 seconds v The roller draws in the card, an[...]

Magnetic Head v If the magnetic head is dirty, errors may occur during writing to or reading of the magnetic stripe card. v Clean the magnetic head after approximately every 1,000 cards. Cautions: v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Before cleaning the magnetic head, make sure tha[...]

9 After the cleaning card is discharged, turn off the power, and install the card hopper . . v To turn on the power again, do so after an interval of at least 10 seconds. Bobbin Holders v If burrs produced by friction with the bobbins are attached to the bobbin holders, they may fall onto the card, ink ribbon, or retransfer film, causing printing e[...]

4 Apply alcohol to a cotton swab (large), and use it to wipe the four bobbin holders (Cotton swab and alcohol: sold separately) . 5 Insert the retransfer film cassette along the guide rail until a “click” sound is heard . . 6 Insert the ink ribbon cassette along the guide rail until a “click” sound is heard, followed by closing the printer [...]

3 Press and hold down the cassette button, and remove the retransfer film cassette (on the left) . 4 Apply alcohol to a cotton swab (large), and use it to wipe the thermal head (Cotton swab and alcohol: sold separately) v Wipe the thermal head with care in the horizontal direction. . 5 Insert the retransfer film cassette along the guide rail until [...]

Servicing Based on Print Output Colors Appear Faded or Dirt is Conspicuous v "Clean the cleaning roller." ( A page 35) v "Clean the fan filter." ( A page 36) v "Clean the card feed roller/heating roller." ( A page 37) v "Clean the bobbin holders." ( A page 40) Card Jam v "Clean the cleaning roller."[...]

When an Error Message is Displayed v Check the error code and error code number displayed on the operation panel. . List of Error Codes v Click on an error code below to jump to the page with the corresponding error descriptions. "44" ( A page 45) "90" ( A page 44) "91" ( A page 44) "92" ( A page 44) "93[...]

Ink Run Out B2 . v Ink ribbon has run out. "Replace with a new one." ( A page 32) Hardware 44 . v A hardware failure has occurred on the printer. Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers. MG Mechanical AB . v An error has occurred in the mechanical component of the [...]

Cards Cards have Run Out v "Replenish the cards." ( A page 31) Card Jam v Error codes are displayed on the operation panel according to the location of the card jam. v Check the error code, and remove the card according to the corresponding procedure. Cautions: v If the card cannot be removed, do not try to do so forcibly. Consult our aut[...]

m If the card cannot be discharged A Turn off the power B Open the printer door, and check the position of the jammed card . C Attach the jog dial to the cleaning roller shaft . . D Turn the cleaning roller shaft in the clockwise direction, while checking the position of the card . E Remove the card after it is discharged from the card load slot Ca[...]

5 Remove the jammed card in the card turn over unit from the card load slot . "If the card cannot be removed" ( A page 48) 6 Install the cleaning unit 7 Attach the jog dial to the card turn over unit shaft, and set the card turn over unit to “Home Pos.” v “Home Pos.” is the position where the slit on the jog dial points to the rig[...]

v Turning the card turn over unit moves the card inside the unit outward. Turn the card turn over unit while turning the cleaning roller shaft so that the card is retained inside the card turn over unit, and set to “Home Pos.”. . Cautions: v Do not turn the card turn over unit forcibly if there is a card inside the unit. Doing so may jam the ca[...]

Error Code Jam(Transfer) 93 v Card jam in the card feed roller. . 1 Press K N B to reset the printer . v The card is discharged from the NG card outlet. . m If the card cannot be discharged A Turn off the power, and detach the card hopper . B Open the printer door, and check the position of the jammed card C Attach the jog dial to the card feed rol[...]

Error Code Jam(Discharge) 94 v Card jam near the card outlet. . 1 Press K N B to reset the printer . v The card is discharged from the card outlet. . m If the card cannot be discharged A Turn off the power, and open the printer door B Pull out the retransfer film cassette, and check the position of the card . C Attach the jog dial to the card feed [...]

Error Code Jam(Retran.) 95 v Card jam near the retransfer heating roller. . 1 Open the printer door v A [Please Remove Jam Card!] or [Please Close Door] message appears. 2 Pull out the retransfer film cassette . Cautions: v The card may be adhered to the retransfer film. Pull out the retransfer film while taking care not to jam it. v If a [Please C[...]

m If the card is inside the printer unit v If the card is not drawn into the card feed roller and is left inside the printer, use the tweezers (supplied) to remove the card. A Turn off the power B Check the position of the card that is left inside the printer . C Pick up the card using the tip of the tweezers (supplied) v Be careful not to drop the[...]

m If the card is caught in the card feed roller to the left of the retransfer heating roller A Turn off the power B Check the position of the card C Attach the jog dial to the card feed roller shaft . . D Turn the card feed roller shaft in the anti-clockwise direction, while checking the position of the card . v The card is discharged from the card[...]

4 Turn the take-up side using your hand until the broken portion can no longer be seen . v Align the yellow side of the unused portion with the arrow indicated on the label of the cassette. . 5 Remove any slack in the ink ribbon . 6 Insert the cassette all the way in along the guide rail until a “click” sound is heard, followed by closing the p[...]

Retransfer Film Retransfer Film has Run Out v "Replace with a new retransfer film." ( A page 33) Retransfer Film is Broken v Repair the retransfer film. Cautions: v If the security lock is on, deactivate it. After work is complete, activate the security lock again. v Stand the cassette on a flat surface as illustrated in the diagram. Avoi[...]

Unable to Fit Retransfer Film Cassette into Printer v With the printer door closed, turn on the power to cancel the transport mode. v While in the transport mode, the retransfer film cassette cannot be installed to the printer with the retransfer film loaded. "Transport Mode Setting" ( A page 29) Unable to Produce Desired Printing Results[...]

Printer not Operating as Desired Card is not Fed into the Printer v Is the card load roller dirty? "Clean the card load roller." ( A page 36) v Is the cleaning roller dirty? "Clean the cleaning roller." ( A page 35) v Is the card thickness correctly adjusted? "Check the adjusted card thickness." ( A page 63) v Are the [...]

Installation and Connection Printer Installation Cautions: v Using the printer in an environment beyond the operating ambient temperature range may result in retransfer or printing errors. Check the “Precautions on installation location” and “Operating environment conditions” specifications. "Precautions on installation location" [...]

Printing Media Installing the Ink Ribbon Cautions: v Stand the cassette on a flat surface as illustrated in the diagram. Avoid doing so on the floor as dust attached to it may cause printing errors. . v Do not touch the inked surface (the side that faces outward when installed) with your hand. Touching it may cause printing errors. Put on the suppl[...]

Installing the Retransfer Film Cautions: v Stand the cassette on a flat surface as illustrated in the diagram. Avoid doing so on the floor as dust attached to it may cause printing errors. . v Do not touch the retransfer face (the side that faces outward when installed) with your hand. Touching it may cause printing errors. Put on the supplied glov[...]

6 Press K N B to reset the printer . Memo: v To avoid printing errors, it is recommended that you forward by one or two images after installing the ink ribbon cassette or retransfer film cassette. "Initializing printer when installing the cassette" ( A page 22) Setting Cards v The card hopper is able to store up to about 100 cards with a [...]

3 Align the orientation of the cards, and set them in the printer m Magnetic stripe cards v Set the card with the magnetic stripe facing upward and toward the printer, or facing downward and toward you. . m ISO contact IC cards v Set the card with the Contact IC terminal facing upward and toward the rear of the printer, or downward and toward the r[...]

Printer and Computer Connection Connecting with a USB Cable Cautions: v While printing is in progress, do not turn off the power of the computer, or switch it to the sleep or standby mode. Doing so may stop the movement of the cards inside the printer. v Plug the USB cable in correctly and firmly. v Do not connect the cable to the USB connectors on[...]

Computer Settings m System Requirements v The printer software runs under the following environments. v Microsoft Windows Vista 32 bit (Service Pack 1) v Microsoft Windows XP 32 bit (Service Pack 2/3) v Microsoft Windows 2000 Professional 32bit (Service Pack 4) v "Software" ( A page 65) v "Install" ( A page 65) v "Uninstall[...]

m Windows Vista v A [AutoPlay] screen appears. . v Clicking [Run SETUP.exe] displays the [User Account Control] screen. v Clicking [Allow] displays the card printer setup screen. 2 Select the [Printer Driver] checkbox on the card printer setup screen A Select the language to use from the [Language] pull-down menu v Selecting [Japanese] switches the[...]

v Enter the shared name when you are sharing a printer. . Memo: v You can also set the shared name after installation is complete. 8 Click [Next] v A port selection screen appears. v Select [CX-7000U Port] under [Create a new port]. . 9 Click [Next] v An install information confirmation screen appears. . 10 Check the installation information, follo[...]

B Select [Install the software automatically (Recommended)], and click [Next] v A [Hardware Installation] screen appears. . C Click [Continue Anyway] v A “Completing the Found New Hardware Wizard” screen appears. . D Click [Finish] v A [Software Installation] screen appears. . E Click [Continue Anyway] m Windows 2000 v A [Digital Signature Not [...]

m Windows 2000 v A [Digital Signature Not Found] screen appears. . A Click [Yes] v A printer installation complete screen appears. . 15 Click [Finish] v Exits the installation program. 16 Open “Printers” in [Control Panel] v Check to ensure that the printer is added. m Windows XP (Example) . m Windows Vista (Example) . m Windows 2000 (Example) [...]

m Windows Vista v A [AutoPlay] screen appears. . v Clicking [Run SETUP.exe] displays the [User Account Control] screen. v Clicking [Allow] displays the card printer setup screen. 2 Select the [Printer Driver] checkbox on the card printer setup screen A Select the language to use from the [Language] pull-down menu v Selecting [Japanese] switches the[...]

10 Click [Next] v A port selection screen appears. v Select [CX-7000N Port] under [Create a new port]. . 11 Click [Next] v An install information confirmation screen appears. . 12 Check the installation information, followed by clicking [Finish] v To change the settings, click [Back]. m Windows XP v A [Software Installation] screen appears. . A Cli[...]

m Windows Vista v A [Windows Security] screen appears. . A Click [Install] part m Windows 2000 v A [Digital Signature Not Found] screen appears. . A Click [Yes] v A printer installation complete screen appears. . 15 Click [Finish] v Exits the installation program. 16 Open “Printers” in [Control Panel] v Check to ensure that the printer is added[...]

Network Sharing of Printer Windows XP/ Windows 2000 Cautions: v Check to ensure that you can access the computer to which the printer is connected. v Check also to ensure that the printer can be shared. 1 Open “Printers” in [Control Panel] v A [Printers and Faxes] screen appears. . 2 Click [Add Printer] under the [File] menu v A “Welcome to t[...]

Cautions: v When the access authority of the computer is not proper, the printer may not be able to perform printing even if installation of the printer driver is completed. Ensure that the access authority is proper according to the instructions of the network administrator. Windows Vista Cautions: v Check to ensure that you can access the compute[...]

Status Monitor Installing the Status Monitor Cautions: v The same status monitor can be used for printers connected via USB and Ethernet. v Make sure that the status monitor is only installed once on a single computer. v To continue using the status monitor after uninstalling the printer driver, update the status monitor accordingly. "Update o[...]

7 Click [OK] v Exits the installation program. v You can now start the status monitor from [Start menu]. Cautions: v The following error may occur when you start executing the status monitor on Windows Vista. . Cause: The status monitor cannot run because the program cannot be identified by Windows Vista. Action: Select “Run as administrator” t[...]

5 Select [Install the software automatically (Recommended)], and click [Next] v A [Hardware Installation] screen appears. . 6 Click [Continue Anyway] v A “Completing the Found New Hardware Wizard” screen appears. . 7 Click [Finish] v Installation of the USB driver is complete. Windows Vista 1 Start up Windows 2 Connect the computer and printer [...]

7 Click [Install this driver software anyway] v An installation complete screen appears. . 8 Click [Close] v Installation of the USB driver is complete. Windows 2000 1 Start up Windows 2 Set the supplied CD-ROM into the computer v The “SETUP.exe” automatic execution program in the CD-ROM is not used. Exit this program. 3 Connect the computer an[...]

Electronic Manual Installing the Electronic Manual 1 Start up Windows, and set the supplied CD-ROM into the computer v A card printer setup screen appears. . Memo: v If the CD-ROM drive of the computer is set to run automatically, the installer will be executed automatically. If the installer is not automatically initiated, double-click “SETUP.ex[...]

Uninstall Cautions: v To uninstall the software, log into the system as an administrative user (Administrators group). v A part of the illustrations in this Electronic Manual may not be displayed depending on the computer’s environment. Skip the procedures in this case. v "Printer Driver" ( A page 80) v "Status Monitor" ( A pa[...]

7 Select the printer to uninstall, and click [Next] v An uninstall information confirmation screen appears. . 8 Check the details, followed by clicking [Finish] v To change a printer, click [Back]. Cautions: v Uninstall the USB printer drivers accordingly for each printer unit number. v An uninstallation complete screen appears. . 9 Click [Finish] [...]

5 Click [Next] v A [Delete the CX-7000 Ethernet printer] screen appears. . 6 Check the details, followed by clicking [Next] v A printer model selection screen appears. . 7 Select the printer to uninstall, and click [Next] v An uninstall information confirmation screen appears. . 8 Check the details, followed by clicking [Finish] v To change a print[...]

Status Monitor Uninstalling the Status Monitor Cautions: v Do not execute “Uninstall” if there are applications that are currently running. v If document printing is currently in progress, wait for all the jobs to complete. 1 Exit the status monitor 2 Select [Uninstall Status Monitor] from [Start menu] . Memo: v If the [Register for start menu][...]

IPSec Setting Procedures . CA.cer PC1.pfx CA.cer PC2.pfx CA.cer Printer01.pfx CA.cer Printer01.pfx Certificate Authentication A Request the “PC Certificate” from the certification authority. B The “PC Certificate” and “Certification Authority Certificate” are issued by the certification authority. Install these on the PC. C Request the [...]

3 Make use of applications such as Windows Notepad to create a preshared key string, and save it as a file with the extension “.key” . v After saving, this file will be downloaded as the “Preshared Key File” when setting “Preshared Key Authentication” using the status monitor. v ASCII characters that can be used for the preshared key of[...]

Memo: v For procedures to set “Certificate Authentication” on the printer, refer to the section of the Status Monitor Settings. "File settings required for certificate authentication" ( A page 116) Certification Authority Certificate File Cautions: v Operate IPSec (IP Security) on Windows by following the instructions of the network a[...]

Printer Driver Settings m "[Setup] Tab" ( A page 87) m "[Print] Tab" ( A page 87) v "[Printing area] Dialog Box" ( A page 89) v "[Color] Dialog Box" ( A page 90) v "[Look up table] Dialog Box" ( A page 90) v "[Dither] Dialog Box" ( A page 91) v "[UV ink] Dialog Box" ( A page 91) [...]

m Using of Resin K ink For specifying the component to print using the Resin K ink. v Extraction Prints the black color component on each page using the Resin K ink. Only text : Prints only the black color text using the Resin K ink. All : Prints all black color components using the Resin K ink. With YMC ink : Prints the background of the specified[...]

[Printing area] Dialog Box Settings related to the printing area using the peel-off ink or areas not to be printed using all YMCKUV inks. . . Directi on of card mov ement H W Y=0 X=0 Abo ut X =87. 5 Abo ut Y=56.0 m Rectangular region Printing area information. m X X coordinate that indicates the start of the area. (Unit: mm). m Y Y coordinate that [...]

[Color] Dialog Box Settings related to color adjustment. . m Brightness Brightness level. m Contrast Contrast level. m Hue Hue level. m Gamma Gamma level. m [Default] button Restores the settings to the default values. [Look up table] Dialog Box Settings related to the look-up table. . m Name Registered name of the look-up table file. You can enter[...]

[Dither] Dialog Box Settings related to dithering. . Cautions: v This setting is enabled only when the [Print mode] item inside the [Print] tab is specified as [2.K] or [5.K+UV], and when the [Page split] is selected for [Using of Resin K ink]. m Image adjustment Image adjustment value. v Dark: Darkens the printed image after dithering. v 0: Defaul[...]

m File information Settings related to the image file to be printed using the UV ink. Memo: v This setting is enabled when [Extraction]-[File] for the front side or back side is specified. m Name Registered name of the image file. You can enter a name up to 30 characters. m File Image file. Click the [Select] button to select a file. "Windows [...]

m [Portrait] Orientation . B C A 1234-5678-90AB 1234-5678-90AB A MAC address printing position when [Upper Right] is selected B MAC address printing position when [Lower Left] is selected C (X=0, Y=0) MAC Address Printing Position Starting X Starting Y Width Height A Upper Right 51.82 mm 64.69 mm 2.88 mm 19.47 mm 612 pixel 764 pixel 34 pixel 230 pi[...]

[Printer settings] Dialog Box Settings related to the printer. Select the checkbox for the setting item to enable, followed by specifying a value. Doing so prints the data using the set values. When the setting is not enabled, data is printed using the preset values of the printer unit. . m YMC ink print level Print density of the YMC ink. Use the [...]

m IC m Non-contact IC encode Allows writing of data to a non-contact IC. m Contact IC encode Allows writing of data to a contact IC. m Turns over the card after IC encoding Turns over the card after writing data to the non-contact/contact IC. m Magnetic m Magnetic encode Allows writing of data to the magnetic stripe. m Turns over the card after MG [...]

Example of Printer Setting Single-sided Printing (Landscape) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: YMC ink + Resin K ink . Setup 96[...]

Single-sided Printing (Portrait) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: Resin K ink . Setup 97[...]

Double-sided Printing (Default) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: YMC ink + Resin K ink . Setup 98[...]

Double-sided Printing (Single-side Lamination) . . m Application software Page 1 v Graphic: colored v Text: colored Page 2 v Graphic: black v Text: black . m Printer Front side v Graphic: YMC ink v Text: YMC ink Back side v Graphic: Resin K ink v Text: Resin K ink . Memo: v If page 2 is set as colored, printing is performed using the Resin K ink af[...]

Single-sided UV Printing . Clicking [UV Ink...] opens the [UV Ink] dialog box. . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: YMC ink + Resin K ink v UV1.bmp: UV ink v MAC address: UV ink . Setup 100[...]

Page Split . . m Application software Page 1 v Graphic: colored v Text: colored Page 2 v Graphic: black v Text: black . m Printer v Graphic: YMC ink + Resin K ink v Text: YMC ink + Resin K ink . Setup 101[...]

Example of Encode Setting Encoding Only (ISO Card) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: none v Text: none m Inline Encoding v Non-contact IC encode data: NIC v Contact IC encode data: IC v ISO track 1 magnetic encode data: ISO . Setup 102[...]

Encoding and Printing (ISO Card) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: YMC ink + Resin K ink m Inline Encoding v Non-contact IC encode data: NIC v ISO track 1 magnetic encode data: ISO . Setup 103[...]

Encoding and Printing (JIS Card) . . m Application software v Graphic: colored v Text: black . m Printer v Graphic: YMC ink v Text: YMC ink + Resin K ink m Inline Encoding v Non-contact IC encode data: NIC v JIS2 magnetic encode data: JIS . Setup 104[...]

Card Turn Over Illustration . . . Tu r ns ove r t he card afte r lo ading Dou ble -sided Logi cal co nfigur ati on of printer Eject Pri nt Mag net ic encode Con tact IC encode Non-contact IC encode Load Tu r ns ov er the card after MG en coding Tu r ns ov er the card after IC encoding Setup 105[...]

Port Monitor Settings v "[Property] Tab" ( A page 106) v "[Version] Tab" ( A page 106) [Property] Tab m USB connection . m Port Name Name of the port. You can enter a name up to 24 characters. m Printer List List of connected printers. The selected printer is used for printing the card. Cautions: The setting is incorrect if the [...]

Status Monitor Settings m What is status monitor? The status monitor is software for displaying the printer status as well as specifying various printer settings. Cautions: v The printer driver needs to be installed on the computer. You can install the printer driver using the CD-ROM supplied with the printer. v Use the status monitor with the powe[...]

Screen Configuration . A Close button Closes the status monitor. B Screen selection tabs Use these to switch to the following screens. v Printer Status Displays the printer’s status. v Printer Setting For displaying and specifying the printer’s print settings. For displaying and specifying the printer’s device settings. v Retransfer For displ[...]

m Printer icons The icon on the left is displayed when the printer is functioning normally. After printing more than 1000 cards since the last cleaning, it changes to the icon display shown on the right. When the right icon appears, perform procedures in "Card Feed Roller/Heating Roller" ( A page 37) under “Maintenance”. . m List of S[...]

[Printer Setting] Tab For specifying the printer settings. Make sure that you take down the set values before making any changes. . m Printer Setting m YMC Ink Print Level For setting the print density of the YMC ink. m Resin K Ink Print Level For setting the print density of the Resin K ink. m UV Ink Print Level For setting the print density of th[...]

[Retransfer] Tab The retransfer settings screen enables you to set the conditions of retransfer to the card. . m Front/Back side settings m Setting procedures v The vertical axis shown in the setting area indicates the retransfer temperature, and the horizontal axis represents the retransfer speed. v Click on the corresponding square to change the [...]

[Bend Remedy] Tab The bend remedy settings screen enables you to set the conditions for the card’s bend remedy. . m Bend Remedy Setting m Setting procedures v The vertical axis in the setting area indicates the bend remedy temperature, and the horizontal axis represents the bend remedy speed. v Click on the corresponding square to change the valu[...]

m Film Type Displays the specification of the loaded retransfer film in the number of images. This is not an indication of the current film level. m [Update] button Applies the selected value to the printer. m [Refresh] button Displays the printer settings on the screen. m Ink ribbon cannot be recognized If the ink ribbon cannot be recognized, the [...]

[Printer Select] Tab This tab is used for selecting a printer and specifying the network settings. . m Current Printer m Selecting a printer Selecting a printer from the pull-down menu switches the display to the current status of the selected printer. m Searching a printer Clicking the [Scan Printer] button displays the search results in the pull-[...]

m Obtain and IP Address Automatically Values such as the IPv4 address can be automatically acquired from the DHCPv4 server. If the DHCPv4 server is not found, settings in the [Use the following IP Address] will be applied. Memo: v For values automatically acquired from the DHCPv4 server, only the IP address is displayed in [Current Address]. v Valu[...]

m File settings required for preshared key authentication A preshared key file is required for preshared key authentication. 1 Select [Preshared Key] for [Download Type], and click [Select...] . 2 Select a preshared key file, and click [Write] . 3 Click the [Close] button on the [IPSec Setting] screen v IPSec setting for the printer is complete aft[...]

[Security Lock] Tab For displaying and setting the security lock status. . m Status Displays the current security lock status. m Setting m [Security Lock] Select [Security Lock], followed by clicking [Update] to activate the security lock. The security lock cannot be activated if a password is not specified. m [Security Unlock] Select [Security Unl[...]

Inline Encoding v "Inline Encoding Format" ( A page 118) v "Character Code List" ( A page 119) Inline Encoding Format v Inline encoding can be performed by enabling the settings in the [Encode] tab of the printer driver settings. "[Encode] Tab" ( A page 94) v Encoding data can be sent to the printer through the printer[...]

Character Code List m ASCII character code list v Below is the list of usable ASCII character codes. Specify the text string to encode using the usable half-width characters for each of the unit codes. . ! " # $ % & ' ( ) * + , - . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ ] ^ _ [...]

List of Error Codes Printer (Error Code:0x01000000-0x01040000) No. Error Code Description Actions (Reference Page No.) 1 0x0102D000 Cards have run out. Replenish the cards. ( A page 31) The card hopper is detached. Install the card hopper. ( A page 63) 2 0x0102D100 The printer door is open. Close the door, and press K N B to reset the printer.( A p[...]

Printer (Error Code:0x01040000-0x02000000) No. Error Code Description Actions (Reference Page No.) 25 0x01044400 A hardware error has occurred. Turn off and on the power again. If the same problem recurs, turn off the power and consult our authorized dealers. 26 0x0104AB00 An error has occurred in the mechanical component of the magnetic encoder. 2[...]

Printer Driver (Error Code:0x02000000-) No. Error Code Description Actions (Reference Page No.) 1 0x02 RRRRRR Printer is not found. Check the printer connection. 2 0x0300274D Printer is not found. Check the printer connection. Printing using a USB-connected printer cannot be performed via Ethernet (LAN) connection. To print via Ethernet (LAN) conne[...]

Frequently Asked Questions v "Printing Settings" ( A page 123) v "UV Ink" ( A page 123) v "Others" ( A page 123) Printing Settings The edge of the image is not printed v Check the printing margin setting in the application software. v About 1 mm from the edge of the image is not printed on the card. Refer to the follow[...]

CX-7000 Card Printer LST1006-002A[...]