NEC MultiSync P750 manual

U ser’ s M a n u a l NEC Professional Series[...]

FCC Information 1. Use the attached specified shielded cables with the JC-1744UMA color monitor so as not to interfere with radio and television reception. (1) Shielded power supply cable. (2) Shielded MultiCable connection system. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has bee[...]

Brightness/Contrast Controls 10 Size and Position Controls 10 Color Control/AccuColor ® Control System 10-11 Geometry Controls 11 Tools 1 11-12 Tools 2 12 Information 12 Specifications 13-14 Recommended Use 15-16 Troubleshooting/Support 17-19 Troubleshooting Chart 17-18 FastFacts ™ Information 19 Technical Support 19 The BBS 19 Electronic Channe[...]

Is the computer a Macintosh II or LC computer? Contents of Package Congratulations on your purchase of the MultiSync ® P 750 ™ color monitor! The following lists all of the items included with your MultiSync monitor package: 1. MultiSync P 750 (JC-1744UMA) monitor with tilt/swivel base 2. Power cord 3. MultiCable ™ connection system 4. User’[...]

3 Is the monitor a MultiSync ® P 750 ™ monitor? If necessary, use the OSM ™ controls to adjust the image to personal preference. Is the image correct? Yes No The installation of your MultiSync P 750 monitor is finished. Enjoy your monitor! See the Troubleshooting section Is the BNC Input being used? Set the BNC/D- SUB switch to the out positio[...]

4 Quick Star t need to use the VID-14 cable adapter in conjunction with the appropriate MultiSync cable adapter when connecting a MultiSync monitor. To attach the MultiSync P 750 monitor to your system, follow these instructions: 1. Turn off the power to your computer and MultiSync monitor. 2. If necessary, install the display card. For more inform[...]

5 Quick Star t 4. Make sure the BNC/D-SUB Switch on the front of the monitor is set to the D-SUB (in) position. For the PC: Connect the 15-pin mini D-SUB (the smaller connector) end of the MultiCable ™ connection system to the connector of the display card in your system. Connect the 15-pin D-SUB (the larger connector) end of the MultiCable conne[...]

6 Introduction Congratulations on your purchase of NEC’s MultiSync ® P 750 ™ color monitor! The MultiSync P 750 monitor delivers superior image quality for all your demanding application needs. The MultiSync P 750 monitor delivers the power you need for today’s high-end applications. The MultiSync P 750 monitor features the latest advancemen[...]

7 Introduction Plug and Play Plug and P lay is the new Microsoft ® solution with Windows ® 95 to provid e automatic peripheral connections without confusing and time-consuming setup. When used with a Plug and Play system and display card, the MultiSync ® P 750 ™ monitor automati- cally tells the system its identification and capabilities. The [...]

8 Introduction Increased refresh rates at all resolutions provide a flicker-free image which is easier on your eyes and extends your viewing time. Depending on the system used, a wide range of graphics standards, including VESA standards, is supported by the MultiSync ® P 750 ™ monitor for PC & Mac including: 640 x 480: 60 to 160 Hz vertical[...]

Controls Control Panel OSM ™ control buttons on the front of the monitor function as follows: Main Menu Sub-Menu EXIT Exits the OSM controls. Exits to the OSM controls main menu. CONTROL Moves the highlighted Moves the highlighted area / area up/down to select up/down to select one of the one of the controls. controls. CONTROL Moves highlighted M[...]

Main Menu Size and Position Controls Left/Right: Moves the image horizontally (left or right). Down/Up: Moves the image vertically (up or down). Narrow/Wide: Increases or decreases the horizontal size of the image. Short/Tall: Increases or decreases the vertical size of the image. Color Control/AccuColor ® Control System Color presets 1 through 5 [...]

decrease the adjustment or selects the color setting (1 through 5). Reset: Resets the current color setting to the factory setting. NEC’s AccuColor ® control system allows you to change your on- screen colors by adjusting the monitor’s red, green and blue color guns individually. You can also access five industry standard color temperature set[...]

in the lock out mode, a screen will appear indicating that OSM ™ controls are locked out. To activate the OSM Lock Out function, press PROCEED , then and hold down simultaneously. To de- activate the OSM Lock Out, press PROCEED , then and hold down simultaneously. IPM ™ System Off Mode: Enable: The IPM System works normally and all stages of en[...]

Specifications Monitor Specifications MultiSync ® P 750 ™ Monitor Notes Picture Tube Diagonal: 17.0 inch 90 ° deflection, 0.25 mask pitch, medium short persistence Viewable Image Size: 15.6 inch phosphor, CromaClear ™ CRT, multi-layered, anti-static screen Radius: 1210 mm coating, semi-tint screen and OptiClear ® screen surface Input Signal [...]

Monitor Specifications MultiSync ® P 750 ™ Monitor Notes Active Display Area (Factory Setting) 306 x 230 mm Dependent upon signal timing used, and does not 12.0 x 9.1 inches include border area. Active Display Area (Full Scan) 316 x 237 mm Dependent upon signal timing used, and does not 12.4 x 9.3 inches include border area. Power Supply AC 100 [...]

Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC ® P 750 ™ COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to danger- ous shock hazards or other risks. Refer all servicing to qualified [...]

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often. • Position the monitor at a 90 ° angle to windows and other light sources to minimize glare and reflections. Adj[...]

Troubleshooting Chart Problem Check These Items No picture • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • The signal cable should be completely connected to the display card/computer. • Check the connector for bent or pushed-in pins. Image is scrolling or [...]

Problem Check These Items Picture bounces or a waving pattern • Move electrical devices that may be causing electrical interference away from the monitor. is present in the picture • See inside cover of this manual for FCC information. Edges of the display image are • Use the OSM ™ Geometry Controls to straighten the edges. not square • I[...]

FastFacts ™ Information FastFacts information is an easy-to-use, automated facsimile service that provides you with information whenever you need it, 24 hours a day, seven days a week. You can call FastFacts information with your touchtone telephone, order a catalog listing the available documents or order the document you need. Within minutes, y[...]

Limited Warranty NEC Technologies, Inc. (hereinafter NECTECH) warrants this Product to be free from defects in material and workmanship and agrees to repair or replace any part of the enclosed unit which proves defective under these terms and conditions. How Long is the Warranty Parts and labor are warranted for three (3) years from the date of the[...]

2. Costs of initial technical adjustments (setup), including adjust- ment of user controls. 3. Payment of shipping and related charges incurred in returning the Product for warranty repair. How You Can Get Warranty Service You have the option of returning this Product to a NECTECH authorized service center or directly to a NECTECH factory for repai[...]

AccuColor ® Control System 10, 11 Advanced Digital Control ™ System 8 ANSI/HFS 16 BBS 19 (Remote Bulletin Board System) BNC 3. 4. 5 Brightness Control 10, 17 Contrast Control 10, 17 C ROMA C LEAR ™ CRT 6, 13 Degauss Control 10, 17, 18 Dimensions 14 Display Area 14 Display Mode 12 Dot Pitch (see Mask Pitch) 6, 13 DPMS 7 Dynamic Beam Focus 6 Ele[...]

More Information More reference information regarding your MultiSync ® monitor is available on NEC’s automated facsimile service, FastFacts ™ information, by dialing (800) 366-0476. Document Information Description Number MultiSync ® Detailed MultiSync P 750 P 750 ™ monitor monitor information 174401 Glossary Definitions of terms related to[...]

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufac- turing, reproduction, use and sales rig[...]

Notes[...]

Part No. 78131312 Printed in U.S.A. MultiSync is a registered trademark of NEC Technologies, Inc. NEC Technologies, Inc. 1250 North Arlington Heights Road Itasca, IL 60143-1248 NEC Professional Series Printed on Recycled Paper[...]