Smeg LSA13X manual

INSTRUCTION MANUAL GUIDE FOR USING THE DISHWA SH ER AND THE WASHING PROGRAMS[...]

[...]

Contents 1 1. Safety and operating instructions ___________________________ 2 2. Installation and hook-up ___________________________________ 5 3. Description of t he controls _________________________________ 9 4. Operating inst ructions ___________________________________ 21 5. Cleaning and maintenance _______________________________ 34 6. Troubl[...]

Safety instructions 2 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLI ANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULL Y READ ALL THE I NSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED B Y A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REG[...]

Safety instructions 3 OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE MAINS POWER CORD AFTER UNPLU GGING IT FROM THE WALL OUTLE T, AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN (LOCKS, DOORS, ETC.). THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIREC TIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT ([...]

Safety instructions 4 LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MA Y CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK. NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP OVER IT. KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO C[...]

Installation instructions 5 2. Inst allation and hook-up Remove the polystyrene bask et retainers. Position the appliance in the desired place of installation. The back or sides of the dish washer may be plac ed up agai nst walls or oth er furniture units. If the dishwasher is installed near a heat s ource, fit the special insulating panel to preve[...]

Installation instructions 6 CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied with the dishwasher. Take care to screw the hose firmly into place with your h ands and then co mplete by tightening about ¼ of a turn with pliers . In dishwasher s equipped with the A CQU[...]

Installation instructions 7 2.2 Electrical connection and precautions CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FORCE. THE PLU[...]

Installation instructions 8 FOR GREAT BRITAIN ONLY: THIS APPLIANCE MUST BE E ARTHED. Fuse replacemen t If the mains lead of this appl iance is fitted with a BS 1363 A 13amp fused pl ug, to change a fuse in this type of plug use an A.S . T. A. approved fuse to BS 136 2 type and proceed as follo ws: 1. Remove the fuse cover A and fuse B . 2. Fit repl[...]

User instructions 9 3. Description of the controls 3.1 Upper panel All the dishwasher controls are gr ou ped on the upper panel. S witch-on, programming, switch-off etc. procedur es are onl y possible when the door is open. 1 ON/OFF BUTTON Pressing this button energises the appl iance. 2 SELECTED PROGRAM INDICATOR LIGHTS Illumination of this light [...]

User instructions 10 8 ENERSAVE OPTION + EXTRA OPTION BUTTON (see “EXTRA OPTIONS” section) Press the button to enable/disable the option. 9 ENERSAVE OPTION LIGHT Illuminates to indicate that the function is activated. 10 HALF LOAD BUTTON Press this button to activate the half load wash option. 11 HALF LOAD LIGHT Illuminates to indicate that the[...]

User instructions 11 PROGRAMS TABLE The manual c ontai ns the pro grams tab le for sev eral mode ls. T o find the table for your d ishwasher, co mpare the pr ogram symb ols at the top of the table with th ose on your con trol panel. SETTING THE WASHING PROGRAM A ND SWITCHING ON After identifying the most suitable pr ogr am with the aid of the progr[...]

User instructions 12 PROGRAMS TABLE PROGRAMM E, NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTES (1) WATER LITRES POWER KWh (1) 1 SOAK Pans and dishes awaiting completion of the load. Cold prewash 15’ *** 3,5 0,02 2 LIGHT Delicate dishes with normal dirt. Wash at 45°C Cold ri nse Rinse at 70°C Dry 65&a[...]

User instructions 13 QUICK TIME PROGRAMS (see relevant section for explanation of functio ning modes) PROGRAMME NUMBER E SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTI (1) WAT ER LITRES POWER KWh (1) 6 RAPID 27’ + Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27'*** 6,5 0,70 [...]

User instructions 14 PROGRAMS TABLE PROGRAMME NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTES (1) WATER LITRES POWER KWh (1) 1 SOAK Pans and dishes awaiting completion of the load Cold prewash 15'*** 3,5 0,02 2 GLASS Glass, china and mixed dishes with light dirt. Wash at 45°C Cold ri nse Rinse at 70[...]

User instructions 15 QUICK TIME PROGRAMS (see relevant section for explanation of functio ning modes) PROGRAMME NUMBER E SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTI (1) WAT ER LITRES POWER KWh (1) 6 RAPID 27’ + Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27'*** 6,5 0,70 [...]

User instructions 16 NOTES AND REFERENCES Only run the soak program wi th half loads. Options cannot be used with the soak progra m. * Standard programme under EN 50242 . If present, the EN ERSAVE op tion must be enabl ed . ** See inform ation sheet provided *** IEC/DIN reference programme. If present, the ENERSAVE option must be enabled . **** Ref[...]

User instructions 17 3.2 Washing programs Before starting a washing program make sure that: • The water supply tap is open. • The correct amount of detergent has been added to the dispenser . • The baskets have been correctly lo aded. • The spray arms are abl e to rotate freely and without obstruction. • The dishwasher door is secur ely c[...]

User instructions 18 SPREAD HALF LOA D Suitable when there ar e not many di shes t o be washed, it saves energ y and reduces the progr am duration. Place dishes in both baskets then load the detergent dispens er than less than the normal amount for a full load. EXTRA OPTIONS - “Flexi Ta bs” BUTTON Press buttons 6 + 8 ( QUICK TIME PROGRAMS butto[...]

User instructions 19 CANCELLING THE CURRENT PROGRAM • To cancel the currently sele c ted program, open the door and hold down the PROGRAM SELECTION (3) button for a few seconds until the indicator lights for programs 4 and 5 illuminate simultaneously (the word "end" is displ ayed on the window). • Close the door. • After approximate[...]

User instructions 20 If the door has to be opened while w ashing is in pr ogress, the pr ogram will be interrupted. The relativ e light will keep flashi ng and a beeper wil l signal that the cycle has not been completed. You must wait about 1 minute before closing the door to rest art the program. When the door i s closed the program will continue [...]

User instructions 21 4. Operating instructions Once the dishwasher h as been correctly installed, pr epare for use as follows: • Adjust the water softening system; • Add the regenerating salt; • Add the rinse aid and deter gent. 4.1 Using the water softening system The amount of scale contain ed in the water (water hardness inde x) can cause [...]

User instructions 22 • Do not use tabl e salt as it contains insoluble substanc es which, over time, may damage the water softening system. • When necessary, refill the r egenerating salt contain er before starting the washing progra m . In this way, the exce ss saline solution will be immediately remove d by the water; the prolonged presence o[...]

User instructions 23 WATER HARDNESS TABLE WATER HARDNE SS SETTING German degrees (°dH ) French Degrees (° dF) 0 - 4 0 - 7 All lights off (no salt) 5 - 15 8 - 25 One light on 16 - 23 26 - 40 Two lights o n 24 - 31 41 - 60 Three lights on 32 - 47 61 - 80 Four ligh ts on 48 - 58 81 - 10 0 Five lights on Contact your local water board for information[...]

User instructions 24 ADDING THE RINSE AID The rinse aid he lps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatic all y added to the water during the final rinse c ycle, from the container situated on the inner side of the door. To add rinse aid: • Open the door. • Rotate the container cap anticlock[...]

User instructions 25 ADDING THE DETERGENT To open the detergent dispenser cap, l ightly press the button P . Add the detergent and clos e the cap carefully . During the washing cycle, the disp enser will be opened automatically. • When a program wi th hot prewas h is selected (see program table ), extra detergent must be placed in the cavity G/H [...]

User instructions 26 Flexi Tabs If you wish to use detergents w hich already contain sa lt and rinse aid, check whether your dishwasher is fitted w ith the " Flexi Tabs option button " on the " Controls description " pag e and then refer to the section which explains how to use this funct ion. If the button is not provided, we r[...]

User instructions 27 WARNING! • Make sure that the dishes are secu rely in pla ce so that they cannot tip over or obstruct the rotati on of the spray arms during the washing cycle. • Do not place very small obj ects in the baskets as these c ould fall and obstruct the spray arms or the wash pump. • Containers such as cups, bowls, glasses and [...]

User instructions 28 4.4 Using the baskets The dishwasher has a capacit y of 13 place-settings , includi ng serving dishes. LOWER BASKET The lower basket receives the full force o f the lower spray arm, and should therefore be use d for the “t oughest” items with a heavier degree of soiling. All types and combinations of loads are permitted, pr[...]

User instructions 29 LOADING THE LOWER BA SKET Carefully load flat plates, soup plates, dessert a nd serving dis hes, positioning them vertically. Pots, pans and their covers m ust be loaded upside down. When l oading soup plat es and dessert bo wls, be sure to leave a gap bet ween them. Loading examples: Examples of loading for inte nsive dirt :[...]

User instructions 30 CUTLERY BASKET The basket has remo vable top gri ds into which items of cutlery should be inserted to keep them properl y spaced and all ow water to pass between them effectivel y. The top grids and central li d are in the bag of accessories . T he central lid functions as a lid only. The top grids can be detached and used sepa[...]

User instructions 31 UPPER BASKET It is recommended to load the upper bask et with small- or medi um-sized items such as glass es, small plates, tea or coffee cups, shallo w bowls and light objec ts made from heat resistant plastic. If the upper basket is used in the lowermost pos ition, it can also be loaded with ser ving dishes, provided they are[...]

User instructions 32 Depending on the mode ls, the basket may be equipped with some or all of the following accessories: - Supports for cups or long ob jects (ladles, spoons…), on the left; can be tipped to the vertical position when not in use. - Long-stemmed glass holder, on t he left; to use, simply lift and fix onto the hooks provided. - Cutl[...]

User instructions 33 ADJUSTING THE UPPER BA SKET The height of the top b asket can be adjust ed to allo w large dishes or pans to be placed in the bottom basket. The adjustment procedure ma y be type A or B , depending on the dishwasher model purchased. V ersion A : pull-out wi th adjustment in two positions. • Pull out both the basket guides. ?[...]

User instructions 34 5. Cleaning and maintenance Before carrying out any work, a lways unplug the appliance from the electrical supply or switch off the a ll-pole dis connection devic e. 5.1 General warnings and recommendations Avoid the use of acidic or abrasi ve detergents. Clean the outer surfaces and door-linin g of the dishwasher regularly usi[...]

User instructions 35 CLEANING THE FILTER UNIT • It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip th e tabs, turn them anticlockwise and lift upwards; • push the centre filter D from the undersid e to remove it from the micro-filter: • separate the two parts which make up th[...]

User instructions 36 BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE: • Check that there are no deposits of sludge or rust inside t he water pipe: if there are, allow the water to run from the water supply tap f or a few minutes. • Plug the power cord back into the socket. • Reconnect the water intake h ose and open the tap again . TROU[...]

User instructions 37 If the dishes fail to dry or remain dull, check that: • there is rinse aid inside the sp ecial container; • the rinse aid dispenser setting is correct; • the detergent used is of good qu ality and has not lost its effectiveness (for example, throu gh incorre ct storage, with the box left open). If the dishes show signs of[...]

User instructions 38 6. T roubleshooting The dishwasher is abl e to indicate a series of malfunctions by illuminating a numb er of lights simultaneo usly (see key b elow); “E” or “Err” (d epending on the m odel) also appear s on the display i n the event of a malfunction. FAU LT DESCRIPTI ON E1 Acquastop failure The anti-flooding system has[...]

User instructions 39 FAU LT DESCRIPTI ON E7 Turbine flow-regulator malfunction (for the relevant models only) The appliance i s not able to "m easure" the amount of water loaded accurately. Interrupt the program and switch off the dish washer. Switch the dishwasher back on, program it again and start the washing cycle. If the probl em per[...]

User instructions 40 TECHNICA L DATA Width 597 ÷ 599 mm Depth measured flush with the outer edge of the control panel 550 mm H e i g h t (depending on models) from 820 mm to 890 mm from 860 mm to 930 mm Capacity 13 Standard place settings Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) Electrical characteristics See rating[...]

c :QUOTE CRITICHE DI CONTROLLO :QUOTE CRITICHE DI CONTROLLO LE AREE O QUOTE MODIFICATE SONO EVIDENZIATE LE AREE O QUOTE MODIFICATE SONO EVIDENZIATE DA SPLINE TRATTEGGIATE DA SPLINE TRATTEGGIATE LE QUOTE O TOLL.MODIF.PER AGGIOR.DEL DIS.AL LE QUOTE O TOLL.MODIF.PER AGGIOR.DEL DIS.AL PEZZO, SONO PRECEDUTE DA "#" PEZZO, SONO PRECEDUTE DA &quo[...]