Advantech TPC-1261H manuel d'utilisation

TPC-1261H GX3 LX800 T ouch Panel Computer with 12.1" SVGA TFT LCD User Manual[...]

TPC-1261H User Manual ii Copyright The documentati on and the software included with this product are copy- righted 2004 by Advantech Co., Ltd. All rights are reserved. Advan tech Co., Ltd. reserves the right to make improvements in the products described in this ma nual at any time without notice. No part of this man - ual may be reproduced, copie[...]

iii Product W a rranty (1 yea r) Advantech warrants to you, the original purchas er , that each of its prod- ucts will b e free from defects in ma t erials and workman ship for one year from the date of purchase. This warranty does not app ly to any product s which have been repaired or altered by persons other than repai r personnel authorized by [...]

TPC-1261H User Manual iv CE This product has passed the CE test for environmen tal specifications when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kin d of cable is available from Advantech. Please contact y our local supplier for ordering information. FCC Class A This equipment has been tested and f[...]

v Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does n ot accord with the table, please contact y our dealer immediately . • 1 x TPC-1261H-A1 • 8 x Panel mounting clampers • 8 x Panel mounting screws • 1 x 3-Pin power connector • 1 x TPC x86 Series support CD ?[...]

TPC-1261H User Manual vi 13. Never open the equi pment. For safety reasons, the equipment should be opened onl y by qualified service personnel. 14. If one of th e follow ing situation s arises, get the equipment checked by service personnel: a. The power co rd or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has be[...]

vii Table of Contents Contents Chapter 1 General Information ....................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ......... .................... .................... ........... ........ 3 1.2.1 System Kernel ..... ......... ...... ......... .....[...]

TPC-1261H User Manual viii Figure 4.14:Update Driver - 1 .......... ...... ......... ......... .... 25 Figure 4.15:Update Driver - 2 .......... ...... ......... ......... .... 25 Figure 4.16:Update Driver - 3 .......... ...... ......... ......... .... 26 Figure 4.17:Slave Bridge In stal la tion Complete ...... .... 26 Figure 4.18:PCI-1602 Device Ma[...]

ix Table of Contents C.2.2 IOCTL _WDT_DISABLE : .. ......... ......... ....... ......... ...... 60 C.2.3 IOCTL_WDT_STRO BE: ....... ...... ......... ......... ....... ...... 60 C.2.4 IOCTL_WDT_GETTIM EOUT: ... ......... ......... ......... .... 61 C.2.5 IOCTL_WDT_SETT IMEOUT: . ......... ......... ......... ...... 61 C.2.6 IOCTL_WDT_REBOOT: .......[...]

TPC-1261H User Manual x Figure F.2: Install Wizard - 1 ........ ......... ....... ......... ...... 84 Figure F.3: Install Wizard - 2 ......... ......... ....... ......... ...... 85 Figure F.4: Install Wizard - 3 ......... ......... ....... ......... ...... 85 F.2 Uninstall the Driver .............. .................... ........... ............ 86 F[...]

2 CHAPTER 1 General Information This chapter gi ves background infor- mation on TPC-12 61H.. Sections include: • Introduct ion • Specifications • I/O Ports Arrang ement • Panel Mounting • Exploded Diagrams • Dimensions & Cutout[...]

TPC-1261H User Manual 2 Chapter 1 General Information 1.1 Introduction The TPC-1261H touch pan el computer is a state-of-the-art HMI (Human Machine Interface). This operator in terface with a 12.1” display is an x86-based platform with th ese key features: • Fanless By using a low-power processor , the system does not have to rely on fans, whic[...]

3 Chapter 1 1.2 S pecifications 1.2.1 System Kernel • CPU: GeodeLin k Control Processor LX 800 500MHz • BIOS: A ward 512KB fl ash memory • South Bridge: GeodeLink Control Processor CS5535 • VGA: GeodeLink Control Pro cessor LX800 500MHz • Ethernet: Realtek R TL8100 BL; IEEE 802.3u protocol compatible • Wa t c h d o g T i m e r : W 83627[...]

TPC-1261H User Manual 4 Environment • Operating T emperature: 0 ~ 50° C (32 ~ 122° F) • S torage T emperatur e: -20 ~ 60° C (-4 ~ 140° F) • Humidity: 40° C @ 10~95% relative humid ity (non-condensing) • V ibration: 1 grms (5~500H z) 1.3 LCD Specifications • Display T ype: TFT color LCD • Size (diagonal): 12.1” • Maximum Resolut[...]

5 Chapter 1 1.5 Powe r • Input V oltage: 18 - 32V DC (the fuse will become an open circu it if the input level exceeds 33 V DC ) • Ty p i c a l : 24V DC @2.5Amp 1.6 I/O Port s Arrangement The arrangement of the I/O ports is shown in Figu re 1.1. Figure 1.1: I/O Port Arrangement 1.7 Panel Mounting 1. There is an adhesive waterproof gasket on the[...]

TPC-1261H User Manual 6 Figure 1.2: Panel Mounting 1.8 Dimensions and Cutout • W eig ht: 4.1 kg (without HDD) • Dimensions: 31 1 x 237 x 58 m m (W x H x D) • Cutout: 302 x 228 mm (suggested)[...]

7 Chapter 1 Figure 1.3: Dimensions[...]

TPC-1261H User Manual 8[...]

2 CHAPTER 2 System Setup This chapter provides a brief explana- tion for operating TPC-12 61H.[...]

TPC-1261H User Manual 10 Chapter 2 System Setup Y ou can easily get TPC-1261H start ed by follow ing the b elow steps. • Step 1: Unpack the TPC-1261H p ackage. Che ck the packing list at the beginning of this manual to make sure all items hav e been inclu ded. Figure 2.1: Unpack the Package[...]

11 Chapter 2 • S tep 2: Install a CompactFlash card containi ng W ind ows CE, embed- ded W indows XP or another operating system . Figure 2.2: Install CompactFlash Memory Card • S tep 3: Connect the po wer connector to the 24 V DC powe r lines. The power lines can either be of some power adapter or in-house power source. Figure 2.3: Power Conne[...]

TPC-1261H User Manual 12 • Step 4: Plug the power lines into the system power receptor . • Step 5: Push the power button to power on the system (figure 2.4). • S tep 6: Calibrate the touchscreen (click "P M" in the botto m corner) . Figure 2. 5: T ouchscr een Icon Figure 2.6: T ouchscreen Calibratio n Note: We are using Wind ows XP [...]

2 CHAPTER 3 System Engine[...]

TPC-1261H User Manual 14 Chapter 3 System Engine T able 3.1: Mainboard Connectors & Jumper Settings Label Fun ction Descripti on CN2 LCD POWER LCD INVERTER Connector CN3 CF Comp actFlash sock et CN4 IDE Internal IDE 44pin(2mm) connector CN5 ETHERNET RJ45 LAN PORT CN6 LPT Printer Port CN7 COM1 Serial port:COM2 RS232 CN8 COM2 Serial port:COM1 RS2[...]

15 Chapter 3 Figure 3.1: Main Bo ard Connectors - 1 Figure 3.2: Main Bo ard Connectors - 2[...]

TPC-1261H User Manual 16[...]

2 CHAPTER 4 Sof tware Configuration Sections include: • VGA D river In stallation • Advantech COM Installation • Entertainmen t Encryption/ Decryption Driver Installation[...]

TPC-1261H User Manual 18 Chapter 4 Sof tware Configuration A support CD-ROM for TPC-1261H is available and along with t he product. There are related utilities and drivers of TPC-1261H for W indows XP . Please insert the support CD-ROM into your CD-ROM driver and inst all the VGA graphics driver , Advantech com driver , T ouchscreen driver and WDM [...]

19 Chapter 4 Figure 4.2: Upda te Driver Step 3: Then follow the update wizard processures. Figure 4.3: Update W izard-1[...]

TPC-1261H User Manual 20 Figure 4. 4: Updat e W izard-2 Figure 4.5: Update W izard-3[...]

21 Chapter 4 Figure 4. 6: Updat e W izard-4 Figure 4.7: Update W izard-5[...]

TPC-1261H User Manual 22 Figure 4. 8: Updat e W izard-6 Step 4: After you successfully upda te the driver , you can see the VGA successfully installed from the de vice manager . Figure 4.9: Driver Installation Complete[...]

23 Chapter 4 4.2 Advantech CO M Driver Inst all T wo com ports name d COM3 and COM4 on TPC-1261H are Advantech Special com port. Please follow the steps below to install th e driver . Step 1: Insert the CD-ROM into your CD-ROM drive. Go to the direc- tory: …TPC-1261HD riverCom Port Driver and th en excute PCI_ICOM.exe Figure 4.10: PCI_ICOM Set[...]

TPC-1261H User Manual 24 Figure 4.12: PCI ICOM Installation - 2 Step 3: Then, go to “Device Manager” to update the driver . Click “?PCI Serial Port” and then select “Driver” T ab to update driver as shown in Figure 4.9 Figure 4.13: Device Manager Screen[...]

25 Chapter 4 Figure 4.14: Update Driver - 1 Step 4: Follow the h ardware upd ate wizard as the figures below . Figure 4.15: Update Driver - 2[...]

TPC-1261H User Manual 26 Figure 4.16: Update Driver - 3 Step 5: Complete the PCI-1602 Se ries Slave Bridge installation. Figure 4.17: Slave Bridge Installation Complete[...]

27 Chapter 4 Step 6: Then, go to “Device Manager”. Y ou can find “Advantech PCI- 1602 Series Slave Br idge” is on the list. Figure 4.18: PCI-1602 Device Manager Step 7: And then click “? PCI Seri al Po rt” to update the driver .[...]

TPC-1261H User Manual 28 Figure 4.19: PCI Seri al port Device Manager Figure 4.20: Update Driver - 1[...]

29 Chapter 4 Step 8: Follow the h ardware upd ate wizard as the figures below . Figure 4.21: Update Driver - 2 Figure 4.22: Update Driver - 3[...]

TPC-1261H User Manual 30 Step 9: Complete the Advantech PCI-1602 Series Master Bridge installa- tion. Figure 4.23: PCI-1602 Master Installation St ep 10: Then, follow the wizard the install the software for Advantech PCI serial ports as the below . Figure 4.24: PCI Serial Port Installation - 1[...]

31 Chapter 4 Figure 4.25: PCI Serial Port Inst allation - 2 Figure 4.26: PCI Serial Port Installation - 3[...]

TPC-1261H User Manual 32 Figure 4.27: PCI Serial Port Inst allation - 4 Figure 4.28: PCI Serial Port Installation - 5[...]

33 Chapter 4 Figure 4.29: PCI Serial Port Installation - 6 Figure 4.30: PCI Serial Port Installation - 7[...]

TPC-1261H User Manual 34 Step 11: After the steps are done, the software for the com3 and com4 is successfully installed. Go to “D evice Manager” and find the list as below . Figure 4.31: Installation Complete 4.3 Entert ainment Encryption/Decryption Driver Step 1: Insert the CD-ROM and go to “Device Manager”. Click “Enter- tainment Encry[...]

35 Chapter 4 St ep 2: Follo wing the instal l shie ld wizard to finish the setup. Figure 4.33: Inst all W izard - 1 Figure 4.34: Inst all Wi zard - 2[...]

TPC-1261H User Manual 36 Figure 4.35: Inst all Wi zard - 3 Step 4: The driver is successfully installed. Y ou can check via “Device Manager” as the below . Figure 4.36: Driver Installation Complete[...]

2 CHAPTER 5 F e a t u r e s i n Windows XP Embedded Sections include: • EWF • HORM • Advantech Utilities[...]

TPC-1261H User Manual 38 Chapter 5 Features in Windows XP Embedded TPC-1261H supports t he embedded W in dows platform . This section out- lines the import ant featur es (EWF and HORM), that are provided in W in- dows XP embedded. 5.1 EWF EWF stands for Enhanced W rite Filter . It provides an upper filter in the storage device driver stack that red[...]

39 Chapter 5 5.2 HORM HORM stands for Hibe rnate Once Resume Many . In HORM environ- ment, a singl e hibernatio n file is used to boot the system repeat edly . T o set a HORM environment, pleas e follow the steps below . Please make sure EWF is disabled. Y ou can run OSUnLock to disable EWF . Enable hibernat ion support: Run ‘power options’ in [...]

TPC-1261H User Manual 40 5.3.1 V ersion Information Start menu-> All Programs -> Advantech This states the current XPE runtime informat ion including hardware plat- form, version, bu ild number , release date, XPE QFEs installed in compo- nent database and XP Pro Patches you installed manually . 5.3.2 OSLock and OSUnLock The two utilities ass[...]

41 Chapter 5[...]

TPC-1261H User Manual 42[...]

2 APPENDIX A Serial Port Settings[...]

TPC-1261H User Manual 44 Appendix A Serial Port Settings A.1 COM1/ COM2/ COM3 Connector Definition Pin Signal 1N D C D 2N R X 3N T X 4N D T R 5G N D 6N D S R 7N R T S 8N C T S 9N R I Note: COM1 and COM2 only supp ort half-duplex (Maximum baud rate: 1 15.2Kbps) 6 5 9 1[...]

45 Appendix A A.2 COM4 Setting The serial por t COM4 on the TPC-1570 H is adjustable. It can be set to RS-23 2, RS-422 or RS-485 . This po rt is desig ned with auto data f low control capability. In other word , the TPC -1570H can automatically detect the data flow direction at this port when the two wired R S-485 communication is activated. COM4 M[...]

TPC-1261H User Manual 46 PIN RS-232 RS-422 RS-485 1 NDCD TX- D- 2N R X T X + D + 3N T X R X + 4 NDTR RX- 5 GND GND GN D 6 NDSR 7N R T S 8N C T S 9N R I[...]

2 APPENDIX B W atchdog T imer Programming[...]

TPC-1261H User Manual 48 Appendix B W atchdog Ti mer Programming B.1 Overview The TPC-1261H watchdo g timer can be used to monito r system software operation and take correc tive action if the software fai ls to function after the programme d period. This section describes the operation of the watchdog timer , and how to program it. The watchdog ti[...]

49 Chapter B B.2 W atchdog T imer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. Y ou must first assign the address of register by writing addr ess value into address port 2E(hex), then write/read data to/from the assi gned register through data port 2F (hex). F[...]

TPC-1261H User Manual 50 T able B.1: W at chdog T imer Registers Address of register (2E) Attribute Descrip tion Read/Write V alue (2F) and description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer . 30 (h ex) write Write 01 (hex) to ena[...]

51 Chapter B B.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;---- --------- ------ --------- ------ -------- ------- ------ ---- Mov dx,2eh ; Unlock W8362 7HF Mov al,87h Out dx,al Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Mov al,07h ; Select registers of watchdog tim er Out dx,[...]

TPC-1261H User Manual 52 Out dx,al Inc dx Mov al,10 Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; l ock W83627HF Mov al,0aah Out dx,al 2. Enable watchdog timer and se t 5 minu tes as timeout interval ;---- --------- ------ --------- ------ -------- ------- ------ ---- Mov dx,2eh ; unlock W83627H Mov al,87h [...]

53 Chapter B Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; Set timeout interval as 5 minutes and start counting Mov al,0f6h Out dx,al Inc dx Mov al,5 Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; l ock W83627HF Mov al,0aah Out dx,[...]

TPC-1261H User Manual 54 Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; l ock W83627HF Mov [...]

55 Chapter B Dec dx ; Enable the function of watchdo g timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; Enable watchdog timer to be strobed reset by keyb oard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al ;---- --------- ------ --------- ------ -------- [...]

TPC-1261H User Manual 56 ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; Enable the function of watchdo g timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;---- --------- ------ --------- ------ -------- ------- ------ ---- Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;W rite 1 to bit 5 of F7 registe[...]

2 APPENDIX C W atchdog T imer Programming on WinCE[...]

TPC-1261H User Manual 58 Appendix C W atchdog T imer Program- ming on WinCE There is a built-in watchdog time r in W indows CE 4.2 for TPC-126 1H. Y ou can access it through the WIN32 API. TPC-1261H provides a WDT driver to allow users to enable/d isable the watchdog timer . The driver name is “WDT1:”. Programmers m ust open this driver before [...]

59 Appendix C C.1.1 Parameters • hDevice [in] Handle to the device that is to perform the operation. Call th e Cre- ateFile functio n to obtain a device handle. • dwIoCo ntrolCode [in] Specifies the contro l code for the operation. Th is value identifies the specific operation to be performed and the type of device on which the operation is to [...]

TPC-1261H User Manual 60 C.2 How to Use the Control Code There are 6 control codes for the op eration codes in the WDT driver . C.2.1 IOCTL _WDT_ENABLE: Enables the watchdog ti mer of your application. By default, if the watch - dog timer is enabled, the WDT driver will auto matically trigger it self after the specified period and your application [...]

61 Appendix C C.2.4 IOCTL_WDT_GET TIMEOUT : Gets the W atchdog time setting. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD points to y our watchdog time setting. The W at chdog time setting is just a number . 0 means 2 seconds, 1 means 5 seconds, 2 means 10 seconds, 3 means 15 seconds, 4 means 30 seconds, 5 means 45 seconds and [...]

TPC-1261H User Manual 62 C.3 Examples #define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_U NKNOWN,ID, METHOD_BUFFERED, FILE_ANY_AC CESS) #define IOCTL_WDT_ENABLE WDT_CODE (0x900) #define IOCTL_WDT_DI SABLE WDT_ CODE(0x901) #define IOCTL_WDT_ST ROBE WDT_CODE(0x902) #define IOCTL_WDT_GET_ TIMEOUT WDT_CODE(0x903) #define IOCTL_WDT_SE T_TI MEOUT WDT_CO DE(0x904[...]

63 Appendix C // Set the W atchdog Timer as 10 seconds. Number 2 m eans 10 seconds. DeviceIoControl(m_h WDT , IOCTL_WDT_SET_TIMEOUT , &nIndex, sizeof(nIndex), NULL, 0, &dwT em p, NULL); // Enable the W atchdog timer DeviceIoControl(m_hWDT , IOCTL_ WDT_ENABLE, NULL, 0, NULL, 0, &dwT emp, NULL); While (1 ) { // do your job here. Sleep(800[...]

TPC-1261H User Manual 64[...]

2 APPENDIX D Accessory Kit Assembly Procedure This appendix sh ows how to connect to a CD-ROM via the CompactFlash slot.:[...]

TPC-1261H User Manual 66 Appendix D Accessory Kit Assembly Procedure D.1 Comp actFlash to IDE T ransfer Kit Please follow this assembly procedur e to use the CompactFlash slot to connect with a CD-ROM drive. 1. Connect the IDE cable to the adapter board. Figure D.1: Adapter Board an d IDE Cable Figure D.2: Connecting the Adapter Board[...]

67 Appendix D 2. Insert the adapter board into th e CompactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.5: Inserted Ad apter Board Note Pin 1 is marke d red[...]

TPC-1261H User Manual 68 Connect the CD-ROM to the adapter board via the IDE cable a n d then connect the exte rnal power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.7: Plugging in the CD-RO M Drive[...]

2 APPENDIX E HDD Kit Assembly[...]

TPC-1261H User Manual 70 Appendix E HDD Kit Assembly TPC-1261H provides two way to assemble the HDD into the system . The ruggized HDD kit is to resist against the high vibration. E.1 Ruggedized HDD Kit Please follow the assembly procedure to install the HDD into the system. 1. Remove th e default HDD cover from the system. The required parts are s[...]

71 Appendix E Figure E.2: Required Parts[...]

TPC-1261H User Manual 72 2. Place the base bracket on the r ear case and carefully pull out the FPC cable thro ugh the hole of the bracket . Figure E.3: Opening the T op 3. Fasten the base on the rear case of the sys t em by 5 screws. Figure E.4: Fastening the bracket[...]

73 Appendix E 4. Carefully connect the FPC cable to the HDD and then put the HDD insultor on the HDD. Figure E.5: Connectting the FPC with the HDD Figure E.6: Placing the HDD insulator on the HDD[...]

TPC-1261H User Manual 74 5. Fasten the HDD holder with the HDD and HDD insulator . Please turn over the HDD holder and fas t en them with 4 screws. Figure E.7: Reverse si de of the HDD holder Figure E.8: Fastening the HDD holder[...]

75 Appendix E 6. Mount th e HDD cushio ns with the H DD holder . Figure E.9: Mounting the cushions - 1 Figure E.10: Mounting the cushions - 2[...]

TPC-1261H User Manual 76 7. Place the HDD holder on the rear cover of the system and then fas- ten the holder with th e system by four screws. Then, the assembly of high vibration resistance HDD module is done. Figure E.1 1: Placing the HDD holder - 1 Figure E.12 : Plac ing the H DD holder - 2[...]

77 Appendix E Figure E.13: Fasten ing the HDD holder E.2 Internal HDD Kit Assembly Please follow the steps to assemble the internal HDD kit. 1. Remove the default HDD cover fro m the system. Figure E.14: Removing the HDD cover[...]

TPC-1261H User Manual 78 2. There are four rubber screw casings , and four screws. Places the screws into their casings Figure E.15 : Placin g a sc rew into its rubber casing 3. Mount the rubber HDD cushions on th e HDD cover . Figure E.16: Mounting the rubber casings[...]

79 Appendix E 4. Connect the FPC cable to the HDD Figure E.17: Connecting the FPC cable 5. Put the HDD into the hole of the rear case. Figure E.18: Inserting t he HDD[...]

TPC-1261H User Manual 80 6. Lay the HD D insulator in righ t direction. Figure E.19: Laying in the HDD insulator 7. Place the default HDD cover on the sys tem. Figure E.20: Placing the cover back into p osition[...]

81 Appendix E 8. Fasten the default HDD cover with the system. Figure E.21: Re-fastening the cover - 1 Figure E.22: Re-fastening the cover - 2[...]

TPC-1261H User Manual 82 9. Place the bracket of PCI/104 on the slot and fasten it into place. Figure E.23: Fastening the PCI/104 bracket - 1 Figure E.24: Fastening the PCI/104 bracket - 2[...]

2 APPENDIX F T ouchscreen Inst allation & Configuration This appendix demonstrates how to install the PenMo unt touchscreen and set the configuration on TPC-126 1H. This section uses Wi ndows XP as an example.[...]

TPC-1261H User Manual 84 Appendix F T ouchscreen Inst allation & Configuration F .1 Driver Inst allation Please insert the x86 TPC series suppor t CD and go to the driver folder: (TPC-1261HDriverUSB t ouchscreen). Click setup.exe Figure F .1: Setup. exe The screen displays the in stallation wizard for the PenMount USB so ft- ware. Click “Ne[...]

85 Appendix F Figure F .3: Install W izard - 2 Figure F .4: Install W izard - 3[...]

TPC-1261H User Manual 86 F .2 Uninst all the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Prog rams. Figure F .5: Uninstall -1 Select PenMount USB. Click Remo ve button. Then, select “Y es” to remove the PenMountUSB dri ver and reboot the system .. Figure F .6: Uninstall -2[...]

87 Appendix F F .3 T ouchscreen Calibration The “PM”, th e icon of th e PenMount Control Panel, is in the menu b ar after the touchscreen installation. Pl ease click the icon “PM” to call Pen- Mount Control Pane l. It contains six functions: Calibrate, Draw , Opti on, and About. About shows the driver version. Calib rate T wo ways to calibr[...]

TPC-1261H User Manual 88 Figure F .8: S tandard Calibration -2 Figure F .9: S tandard Calibration -3[...]

89 Appendix F Advanced Calibration is for the aged touchscreens by using 4, 9, 16 or 25 points to calibrate touch panel. Figure F .10: Advanced Calibratio n -1 Note T ouch the red squares in sequ ence. The cali- bration is completed af ter the fif th touch red point is calibrated. Pr ess “ESC” to skip.[...]

TPC-1261H User Manual 90 Figure F .1 1: Advanced Calibration -2 Figure F .12: Plot Calibratio n Data[...]

91 Appendix F Draw This is to test the touchscreen operatio n. Its display shows touch loca- tion. Figure F .13: Draw Click “menu” and then click “clear screen” to clear the drawing. Note Plot Calibratio n Data en abled provides the blue lines to show linearity before calibr ation and black lines to show lin earity af ter calibratio n when [...]

TPC-1261H User Manual 92 Figure F .14: Clear Screen Option This option is to set t he operation m ode and beep sounds if the beep sound is enabled. The operation mode, stream mod e and point mode, is to enable/ disable the mouse’ s ability to drag on-screen icons. Stream mode let the mouse functions as normal and dragging on -screen. Point mode i[...]

93 Appendix F Figure F .15: Opti on[...]

TPC-1261H User Manual 94[...]

2 APPENDIX G Fuse S pecifications[...]

TPC-1261H User Manual 96 Appendix G Fuse S pecifications G .1 Fuse Specifications Ratin g: 250 V AC , 5 A Size: 5 x 20 mm G .2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse co ver back into position. Figure G .1: Fuse Replacement Note For your protection, the fuse is set to bre[...]